Search Documents

Commodities statistics and otter information are available through the following t et systems: Internet Access: To acccess the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, enviromental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

By R. V. Higgins

This report presents the results of a study of water injection in the HX sub-pool fault block V-B, in the Upper Terminal zone, Wilmington field, California, and is based on data obtained to May 1957. An earlier report3/ describes the results of gas injection in part of the field. The principal purpose of the pilot flood was to determine whether a sand having a permeability of 1,200 millidarcys and containing oil having a viscosity of 17 centipoises could be waterflooded effectively. The results of a preliminary study by engineers of the Long Beach Harbor Department of oil recoveries from areas where encroaching edgewater was active and the results of an independent study by a consultant retained by the Long Beach Harbor Department were favorable to a trial waterflood. After these preliminary studies, a detailed petroleum-engineering exam-ination was made of the technical details. As a result, a peripheral flood was started in June 1953. The peripheral flood was deemed desirable because the producing wells are bottomed a short distance from the edgewater. The HX subpool was selected for the pilot test because it is an isolated section of the Upper Terminal zone and is separated from the adjoining pools by faults on the east and west and by edgewater on the north, south, and west. Several petroleum-engineering methods were applied to evaluate the performance of the waterflood, and all showed that injecting water stimulated oil production.

Jan 1, 1958

By E. C. Pattee

A mobile spectroscopic laboratory was completed by the Bureau of Mines in 195 to provide a rapid, inexpensive means of field testing samples for beryl¬lium and other associated metals of possible commercial importance. Spectro-copes have been used in laboratories for many years in various types of research and routine analyses, but this spectroscope is probably the first mobile unit. The laboratory provides for spectroscopic, radioactivity, fluorescent, and limited chemical tests of samples. The unit has been a valuable reconnaissance tool. It has been used to search for beryllium, cesium, columbium, tantalum, rubidium, and lithium in Idaho, Washington, and Montana. Several very low grade deposits of these elements were found, and occurrences of other important elements were identified; however, none are of economic importance. The spectroscope permits the detection of elements by analysis of visible light produced when elements in a small powdered sample are volatilized in an electric arc., A total of 70 elements can be detected; 29 can be detected at or below 0.01 percent, Electric power for the arc is supplied by a gasoline motor-driven generator, Equipment is housed in an aluminum van, mounted on a 4-wheel-drive vehicle for easy maneuverability on mountain roads, A trailer with crushing, pulverizing, and splitting equipment permits the reduction of samples to a small representative pulp.

Jan 1, 1963

By R. Blickensderfer

Several thin film absorber stacks with spectrally selective characteristics were developed by the Bureau of Mines. The stacks consisted of a silicon thick film or a zirconium compound thin film on a reflective thin film of silver. The zirconium absorber films, with the general formula ZrCxOyNz, were prepared by reactively sputtering zirconium or zirconium carbide in argon with small amounts of oxygen, nitrogen, or both, or by oxidizing zirconium films in air. A few similar types of films were prepared from titanium. The short-wave absorptance over the solar spectrum, a(s), and thermal emittance at 600 K, e(600 K), of the solar absorber stacks were calculated from room-temperature reflectance data. The values of a(s) ranged from 0.47 to 0.93, e(600 K) from 0.49 to 0.034, and the ratio a(s)/e(600 K) from 1.7 to 34. The specimen with the best combination of properties, a ZrNx-Ag stack, had a solar absorptance a(s) of 0.85 and a ratio, a(s)/e(600 K), of 24. The effect of film thickness and composition on spectral selectivity was determined. An emissometer for measuring normal total emittance up to 800 K and a method for determining a (s), e(T) (hemispherical), and a(s)/e(T) using simulated solar radiation are described. A calorimetric method for measuring a(s) and e(T) (hemispherical) at elevated temperature is also described. Measurements made on several specimens agreed favorably with calculated values.

Jan 1, 1976

By Carl Rampacek

The conversion of dilute sulfur dioxide gas into sulfuric acid by autoxidation in mechanical cells of the flotation or gas absorber types was investigated. Bench-scale tests were made with sulfur dioxide-air mixtures to determine the influence of several factors on autoxidation of sulfur dioxide, using iron and manganese salts as catalysts. The laboratory investigation subsequently was extended to pilot plant acid-making tests, using a modified turbomixer gas absorber having a 12-inch-diameter impeller. Sulfur dioxide gas was produced for the tests by roasting pyrite in a fluidized-bed reactor. In the better tests, made with manganese sulfate as the catalyst, the equivalent of 1,000 pounds of anhydrous H2SO4 was produced per 24 hours as a 10-percent solution; power consumption was 0.2 kwhr per pound of equivalent anhydrous acid synthesized. The batch and continuous tests demonstrated the technical feasibility of producing dilute sulfuric acid by autoxidation of sulfur dioxide gas in mechanical cells when converting pyrite roaster or waste smelter gases.

Jan 1, 1963

By Elton L. Litchfield

The Bureau of Mines determined minimum energies for direct initiation of expanding gaseous detonation waves in acetylene-oxygen mixtures. Composition limit ranges for the initiation of detonation with fixed energies have been compared to data in the literature. Assuming that the stored electrical energy is completely converted to thermal energy, the agreement between the energy of primary explosive initiators and the energy of electrical discharge initiators was good. Minimum energies for initiation of detonation in the most sensitive composition (40 percent C20 plus 60 percent 0 2) were: 0.64 joule at an initial pressure of 1/4 atmosphere, 5.0X10-2 joule at 1/2 atmos¬phere, and 3.7X10-3 joule at I atmosphere. Fuel concentrations in mixtures initiated to detonation by 4.9X102 joules ranged from 10 to 65 percent C2H2 at 1/4 atmosphere, 10 to 67 percent C2H2 at 1/2 atmosphere, and 9 to 68 percent C2H2 at 1 atmosphere.

Jan 1, 1967

By Constantine C. Popoff

During 1946 several limestone deposits near Fortson, Snohomish County, Wash., were examined by the Bureau of Mines. These examinations were part of a long-range investigative program of regional mineral supplies required by the anticipated industrial development of the Pacific Northwest. The .study outlined in the following paper was specifically undertaken to disclose new sources of high-purity limestone and to appraise, their economic aspects. The deposits examined -namely the Galbraith, Climax, and Hi, Hi -are somewhat similar in physical features and geologic environment. They are lenticular and belong to the same formation of metamorphosed sediments that underlies the prominent Whitehorse Ridge.

Jan 1, 1949

By E. Wittenau

This paper describing the concentrator practice of the Copper Queen Branch of the Phelps Dodge Corporation at Bisbee, Ariz., is one of a series of papers on milling methods and costs being prepared by the United States Bureau of Mines. The Copper Queen Concentrator treats 4,000 tons of copper ore daily by preferential flotation, whereby the copper sulphides are floated and considerable iron pyrite is depressed. During 1929 the heads to the concentrator averaged 2.15 per pent of copper, the recovery was 91.32 per cent of the total copper, and the concentrates produced contained 12.92 per cent of copper.

Jan 1, 1931

By J. Howard Bird

The purpose of this publication is to discuss grounding mediums and the phases of grounding related to corrosion and cathodic protection. The material presented is believed to contribute to a better understanding of this subject. It also indicates more effective methods of reducing corrosion damage to metal structures and equipment in the mining industry by cathodic protection. The authors do not intend to discuss technical aspects but rather to explain the general principles of this method of inhibiting corrosion. The relationship between soil resistivity, protective grounding, and corrosion is presented. Corrosion causes the annual loss of billions of dollars; which can be greatly reduced. Losses in the mineral industry can be excessive owing to the extensive use of direct-current power, the presence of considerable dampness, and the frequent, indiscriminate use of dissimilar metals.

Jan 1, 1958

By W. H. Ode

An investigation of standard methods for determining ash in low-rank* coals showed that generally 60 to 95 percent of the total sulfur in the coal is retained in the ash as SO3. This large sulfur retention causes a positive error in the determined mount of ash of as much as 6 percentage points for the coals examined, although it usually is 2 to 3 percentage points for lignites and about 1 for subbituminous coals. Unless the sulfur content is low or unless a correction is made for the SO3 retained, the fixed carbon and oxygen have an equivalent negative error when determined by difference; also other inaccurate analytical values occur when the data are calculated on an ash- free bas is. No simple modification of the ashing procedure was found that would reduce the sulfur retention to a point where its effect on the ash determination would not be significant, Therefore, for accurate analytical work on law-rank coals, the SO3 should be deducted from the determined ash to obtain a "corrected" ash value.

Jan 1, 1962

By N. H. Coates

A small, special-purpose centrifugal compressor was developed to circulate 60 pounds per hour of helium at 1,000° F and 250 psig because standard, commercial units were not available. Performance characteristics of this compressor were determined at helium flows of 2,000 to 18,000 std cu ft per hour, pressures of 100 to 250 psig, and temperatures of 100° to 1,000° F. This range is 2 to 90 actual cu ft per minute. Several graphs show the adiabatic head developed by the compressor over this wide flow range at various combinations of temperature and pressure. A compressor performance map relates pressure ratio to mass flow, temperature, pressure, and speed. This map can be used to accurately predict compressor performance factors within the range of operating conditions covered by the experiments.

Jan 1, 1963

By John Paul Gries

During World. War II, when the curtailment of imports led to an unprecedented demand for domestic mica, beryl, spodumene, and other pegmatite minerals, the Bureau of Mines and the Geological Survey entered upon a program designed to expedite mining of these minerals from the Black Hills area of South Dakota. The program involved napping, sampling, and drilling of many pegmatite dikes in the southern portion of the Black Hills and beneficiation conducted in the field and in the Bureau of Mines laboratories at Rapid City, S. Dak., Rolla, Mo., Salt Lake City, Utah, and College Park, Md. This report describes the occurrence and sampling of the Beecher No. 2 pegmatite, which was investigated as part of the general pegmatite study in South Dakota. Investigation of the Beecher No. 2 pegmatite was started on November 20, 1943, and terminated in the spring of 1944. During this period, the Bureau of Mines took a series of trench samples across the pegmatite at the surface for grain-count studies and chemical analyses. The Geological Survey mapped the geology of the deposit after it was exposed by trenching and stripping.

Jan 1, 1950

By Robert K. Koch

The reactions of alumina and alumina monohydrate with wet hydrogen fluoride gas were studied by the Federal Bureau of Mines to determine the feasibility of producing commercial-grade aluminum fluoride from offgases generated by pyrohydrolysis of siliceous fluorspars. The test results showed than an aluminum fluoride reactor operating at maximum efficiency could retain 96 percent of the fluorine contained in off-gases generated by pyrohydrolysis of siliceous fluorspar. The requirements are a reactor temperature of 200° C. and a reactor entrance gas containing 5 mole-percent hydrogen fluoride. Partial pressure equilibrium constants were determined for the reaction of alumina monohydrate and wet hydrogen fluoride gas from 200° to 350° C. and for the reaction of alumina and wet hydrogen fluoride gas from 350° to 700° C. Both reactions are reversible, and they proceed in directions that are dependent upon the temperature and the relative HF:H2O concentration. Logarithms of the equilibrium constants were used to plot the reaction isobars; these can be used to calculate the theoretical maximum efficiency of a reactor processing wet hydrogen fluoride gas between 200° and 700° C. The theoretical maximum efficiency decreases with increasing temperature.

Jan 1, 1961

By J. Tomlinson

Shuttle car trailing cable splices were tested for resistance to failure upon being subjected to repeated bending, abrasion, and tensile shocks using a new testing method that closely simulates shuttle car induced stress. The results show that under normal stresses, splices can be made to withstand the equivalent of three months of operational use. Restoring the tensile strength to the conductors is found to be as critical as restoring flexibility. Splices in which the conductors are of slightly unequal length did not present as serious a workmanship problem as previously thought since test results show that the conductors tend to equalize when longer cables, in contrast to short cables employed in previous testing methods, were used. Dynamic recordings of cable tensile stresses are presented for a shuttle car and the new simulated testing method. Two simple but effective methods for removing insulation using a knife and a pair of pliers are described. None of the designs tested for a sacrificial splice covering were satisfactory.

Jan 1, 1979

By Robert L. Virta

The Bureau of Mines examined a fibrous talc sample from the Gouverneur talc district in New York by transmission electron microscopy (TEM) and polarized light microscopy to determine the mineralogical relationship of the fibrous talc to the amphiboles present in the sample. Two am-phiboles, anthophyllite and tremolite, were present in the sample. Tremolite occurred as a separate mineral phase, which was blocky in habit. Only a few composite tremolite-talc grains were observed. An-thophyllite, however, was present only in the fibrous talc grains. Mi-crodiffraction study of the fibrous talc grains containing anthophyllite showed that the anthophyllite was intermixed with the talc on a fine scale and that there was a crystallographic relationship between the talc and anthophyllite lattices in the fibrous talc grains. A mechanism similar to the process that forms biopyriboles could explain the structural defects, the fibrous habit of the talc, and the structural relationship between the talc and anthophyllite in the fibrous talc grains. Because of these characteristics, phase contrast microscopy and a provisional TEM technique for monitoring asbestos exposure would not distinguish between fibrous talc and fibrous amphiboles. TEM techniques employing electron diffraction and energy-dispersive X-ray analysis are recommended to positively identify the fibrous phases for regulatory purposes.

Jan 1, 1985

By R. E. Campbell

Uranium metal of improved purity was prepared by electrorefining commercial magnesium-reduced uranium in a molten sodium chloride-uranium trichloride electrolyte. The best operating conditions for the preparation of refined metal were established as follows: an electrolyte containing 8.7 to 13.3 weight-percent uranium; initial cathode current densities from 300 to 1,500 amp/sq ft; and a molten salt temperature of 860° C. Ingots produced from electrorefined uranium crystals prepared with these operating conditions were substantially free of metallic impurities. The only impurities in the refined and consolidated metal were present in low or undetectable amounts.

Jan 1, 1965

By L. J. Froisland

An integrated process for recovering metal from nonmagnetic auto-shredder reject scrap was investigated by the Federal Bureau of Mines. The methods used were air classification, water elutriation, screening, magnetic separation, handpicking, and heavy-media separation. Metal recoveries in this process were projected at 39 percent copper and copper alloys, 53 percent aluminum, 96 percent iron, and 98 percent zinc die cast. An economic evaluation of the conceptual process indicated that a facility designed to reclaim the reject scrap from 200 shredded automobiles daily could be profitable. Total investment in this plant was estimated at $321,000; the discounted rate of return before taxes was 53 percent.

Jan 1, 1975

By Richard F. Hewlett

Computing average grade and tonnage either for an entire ore deposit or for individual blocks of ore is a continuing problem in mining. As part of a research program, investigating application of statistical techniques to mine sampling, Bureau of Mines engineers at the Denver Mining Research Center have made extensive use of an electronic digital computer for developing mine sampling theory, simulation of ore deposits, and analysis of mine sample and assay data. This report is one of a series describing use of the digital computer for rapid solution of computing problems in the mining industry.3 4 Development of a computer program to compute ore reserves by the commonly used triangular method was necessary so that results could be made available for analysis within hours.

Jan 1, 1963

By John Dixon

This paper is one of a series on milling methods and costs being published by the Bureau of Mines. Acknowledgment is made to J. B. Tyrrell, managing director, and Wm. Sixt, manager of the Kirkland Lake Gold Mines, for permission to publish this article. The Kirkland Lake Geld Mining Co.'s mill is located on Government Road at the west end of the productive part of the Kirkland Lake mining area, 1 mile west of the village of Kirkland Lake. The crushing plant is connected to the shaft house of No. 2 shaft, which is now the only operating shaft.

Jan 1, 1931

By D. Montagna

This Bureau of Mines report describes a salt-free, fluxless method for reclaiming metallic aluminum from aluminum dross. The dross is smelted under argon, nitrogen, or carbon dioxide, instead of a salt flux, in an externally heated pot furnace. Aluminum recovery, using argon, is equal to recoveries reported from commercial smelters that process dross in rotary-type furnaces This salt-free method could offer a reduction in air pollution, lower energy requirements by elimination of salts, and the production of up to 60 percent less solid waste for disposal than the salt method.

Jan 1, 1978