Search Documents

By Donald H. Koch

The project investigated the impacts of coal and mineral storage piles on both ground and surface water quality. The study consisted of two major tacks, Task 1 had two phases. The first phase was field investigations in which ten cons and mineral stockpile sites (5 coal, 5 mineral: phosphate, lead, copper, iron, uranium) across the country were visited to determine the actual impart of coal and mineral stockpiles on writer quality. The second phase of Task I was a series of leaching experiments in which drainage from the ten coals and minerals was controlled and monitored to survey the extent to which storage piles release toxic ions to ground and surface waters. Task IT was n review of pollution abatement techniques with three generic treatment examples applied to lead-zinc ore, eastern coal, and uranium ore stockpile leachate. Major conclusions drawn from the completion of Tasks I and II include: water quality impacts are site specific, there is n high correlation between sulfide content of u material and its solution potential, and the selection of the best treatment alternative for n specific coal or mineral storage area must be based on site-specific criteria, pilot studies on representative leachate samples, and sound engineering design.

Jan 1, 1982

By N. Fragen, H. H. Stroch

"INTRODUCTION A previous paper by H. H. Storch 4 described. three processes for the production of potassium sulphate from polyhalite (K2S01.MgSO1.2CaS04.2H2o), Since these processes depended upon calcination of polyhalite followed by leaching with water at 100°C., the fundamental reactions occurring in these steps were discussed in detail. This paper, which describes processes producing syngenite (K2S04.CaSO4.H2O) and potassium sulphate and gives data concerning the production of by-product magnesia, presents the results of work performed at the Non metallic Minerals Experiment Station of the U. S. Bureau of Mines, maintained at New Brunswick, N. J., in cooperation with Rutgers University.A study of the solubility relationships of the system 5 Ca++ -Mg++ -K+-SO4 = H20 at 25ºC. shows that syngenite is stable in the presence of a concentrated MgSO4 solution, the K2SO : equilibrium concentration being comparatively low (2.6 per cent), The processes described below, which involve the conversion of calcined polyhalite to syngenite, are based on the 25°C. equilibria. It has further been found that syngenite can be decomposed by water at 100ºC, yielding a 9 to 10 per cent K250 solution, the solid phase being potassium calcium pentasulphate (K2SO, 3CaSO.H2O, hereafter referred to as ""pentasulphate""). This latter compound is unstable in the presence of water at 25°C., its decomposition resulting in a solution containing about 3 per cent of K2SO4 and a solid phase consisting of gypsum. This behaviour of syngenite with water at 100°C. and of pentasulphate with water at 25ºC. constitutes the basis of processes for the production of K2SO4 by way of the conversion of calcined polyhalite to syngenite,Syngenite is a product which may be used as a fertilizer per se. As produced in the process to be described, it contains about 50 per cent of K2SO1, and will readily give up its potash content on treatment with water, although the limiting concentration at ordinary temperatures is approximately 3 per cent. This definite but limited solubility should make this product more desirable as a fertilizer then the more concentrated forms of potash salts which have higher solubilities and hence involve the danger or plant injury due to a high local concentration of potash."

Sep 1, 1931

By William E. Young

There are many large rhodonite-bearing veins containing manganese in the Eureka-Animas Forks area of the San Juan Mountains in Colorado. The Sunnyside vein is the largest known vein in the area. As observed on the surface, the vein is mineralized over 8,000 feet and attains a maximum width of 200 feet. The average width of the vein and its branches and ramifications is 58 feet in the area that was mapped in detail. The weighted-average analysis of surface and underground samples from the northeastern extension of the Sunnyside vein is 8 percent manganese. Most other known veins in the area have a similar manganese content. The Hidden Treasure vein lies southeast of the Sunnyside-No Name-Mastadon vein. The weighted average of the analyses of surface and underground samples from this vein is 13 percent manganese. Exposures of the Scotia-Silver Chord vein are visible over a strike length of 4,000 feet on Treasure Mountain. Diamond-drill holes show that the vein contains 10 percent or more manganese to a depth of 400 feet. The vein has an average width of 28 feet. The Independence vein is exposed on the surface for a distance of 600 feet and has an average width of 6 feet. Three cut samples taken across the vein had an average content of 20.7 percent manganese. Sampling of the outcrops of eight veins in the Placer Gulch area also indicates manganese. Numerous other veins cropping out in the surrounding area are similar to the outcrop of the Sunnyside vein system mineralogically and are worth investigating.

Jan 1, 1966

By H. Tomlinson

"INTR0DUCTIONThis publication is a third of a series devoted to falls of roof and coal in coal mines of the Western States. It gives the results of examinations of the mines of the Rock Springs coal District of Sweetwater County, Wyo., which represent the principal coal beds therein and approximately 75 percent of total production of the State.A study was made of safety conditions at all the producing mines of the district and suggestions were offered the operators regarding methods and practices which would, in the opinion of the writer, provide additional safeguards to prevent accidents from falls of roof and coal.In presenting the subject, consideration must be given to such features as character of the coal beds, depth of cover. methods of mining, timbering practice, roof testing and supervision, and for comparative purposes to certain statistical matter bearing upon relation of accidents to their causes, tonnage produced, men employed, days worked, and lost days due to accidents during the 3—year period covered by this study.ACKNOWLEDGMENTSThe writer acknowledges the cooperation of the officials of the various coal companies, without whose assistance this work could not have been completed.F0UR REPRESENTATIVE COAL OPERATIONSThis report relates to four representative coal operations in the Rook Springs district of Sweetwater County, Wyo., which are referred to as mines A, B, C, and D. This group employs yearly an average of 993 men, representing 37 percent of the men in coal mines of the county, and has an average annual production of 1,484,373 tons, representing approximately 44 percent of the coal produced in the county. Figure 1 is a map of the Rook Springs coal district."

May 1, 1933

By G. S. Rice, H. O. Howarth, Greenwald. H. P.

"Electricity as a means of transmitting power was introduced in coal mines of the United States about 1891 for both haulage and coal cutting, only a few years after electrical haulage was first installed on street cars. At first, the hazards of electrical ignition ere not appreciated and the general use of open lights and black blasting powder made the possibility of electrical ignition of fire damp seem small by comparison.5 The possibility of igniting coal dust directly by electric sparks or arcs had not been considered.In the nine years prior to 1900, the progress of introducing electricity underground was slow, except that it was used for lighting shaft bottoms. Electricity had to contend with the more general use of compressed air for coal-cutting machines and, in mainline haulage, with the use of mule-teams and endless and tail-rope systems. During this period, great improvements were made in electrical apparatus, in surface installations as well as in mines. By 1900, therefore, the technique of applying electricity in mines had so far developed that it rapidly drove out the use of compressed air in coal mines because of the comparative ease of its installation and the marked economic advantages of its use over that of compressed air in practically all kinds of mining machines except percussion. rock drills.At this time, however, little thought was given to the hazard of indiscriminate use of electricity causing explosions and fires, and the possibility of electricity causing direct ignition of coal dust had not been considered. On December6, 1907, however, the Monongah, West Va. mine explosion occurred. This was the greatest mine disaster this country has over had, 361 men being killed. Although: there was much diversity of opinion, as to the origin of the explosion, many well-informed engineers concluded that the cause was ignition of coal dust do to wreckage of a runaway trip in a rope haulage entrance slope. This slope also served as a ventilating and it extended from the level of the coal bed to the surface. The runaway trip tore down electric cables and stirred up a cloud of dust when it was wrecked at the bottom of the slope. The dust was probably ignited by the electric arcing that occurred when the wires were knocked down. (Another but less probable source of ignition was the open flames of miners lamps.) From the foot of the slops the explosion appeared to have travelled into the mine, spreading as it went. If this ignition of coal dust was the origin of the explosion, it occurred on pure intake air entering directly from the surface."

Oct 1, 1930

By C. W. Elder

"INTRODUCTION This report describes a method of horizontal drilling in an oil-producing formation underlying a 400-acre, approximately square plot of land in the Franklin Heavy oil field in Sugar Creek Township, Venango County, Pa. The method, which was developed on two previous projects in Ohio, 3/ consists of sinking a shaft to the bottom of a shallow oil sand and drilling holes in a general horizontal plane outward from the chamber in a pattern similar to that of the spokes of a wheel. The project was undertaken by the Venango Development Corporation in an attempt to find an efficient method of recovering oil from partly depleted sand formations.The Venango Development Corporation is composed of the following oil-producing and oil-refining companies and individuals: South Penn Oil Co., Forest Oil Corporation, Kendall Refining Co., Minard Run Oil Co., Quaker State Oil Refining Co., The Pennzoil Co., Alliance Oil Corpo¬ration, United Refining Co., Franklin Creek Refining Corporation, Canfield Oil Co., Pennsylvania Refining Co., Page Oil Co., Freedom Oil Co., D. W. and D. S. Grant, and J. P. Herrick, C. M. Davison and N. V. V. Franchot. Engineering features of the project were supervised by a committee off three engineers A. J. Saxe, chairman, W. M. Shoemaker, and C. N. Pfohl, who supervised the excavation of the shaft and the drilling of the first two holes by alternately spending a week at a. time at the project. The drilling method was under patent license from Leo Ranney, who served as technical advisor to the Venango Development Corporation; in addition, he furnished the design for the shaft and work chamber."

Sep 1, 1944

By L. F. Heising

This report is a general summary of pertinent data on the manufacture and use of synthetic ammonia products. It provides a condensed summary of the potentialities of a synthetic ammonia industry in North Dakota for Federal, State, and private organizations that may be interested in helping to develop an integrates synthetic ammonia and fertilizer industry. The report contains discussions of: (1) Materials used in the manufacture of nitrogenous fertilizers, nitric acid, and urea; (2) National production, imports, exports, and consumption; (3) the ammonia industry, location, capacity of plants; (4) processes used in manufacturing synthetic ammonia, nitric acid, and urea; (5) other potential industries; and (6) analyses of manufaturing and plant cosh;. Additional information on industrial compounds from ammonia and plant nutrients removed by crops is given in Appendixes 1 and 2. Synthetic ammonia is one of the primary ingredients in fertilizers. Resources required in synthetic ammonia manufacture are available in North Dakota. Hydrogen is available from the petroleum and natural gas resources, particularly in the Williston Basin, and from the large lignite resources in the State. Hydrogen can be produced from lignite by a gasification process developed by the Bureau of Mines at Grand Forks, N. Dak.

Jan 1, 1954

By L. A. Neumeier

The Bureau of Mines evaluated the properties of zinc alloys containing 25 to 40 wt pet Al and 0 to 0.7 pet Mg. Microstructures, hardness, and tensile properties were evaluated for material as extruded at 285° C, solution treated at 300° to 400° C, and subsequently aged at 100° to 200° C. The alloys without magnesium are characterized by low hardness and strength with high tensile elongation and reduction in area. It was verified that magnesium effectively retards the Zn-Al eutectoid transformation below 275° C and markedly increases hardness and strength with decreases in ductility. Solution treating at 350° C results in large grain sizes and gross embrittlement. Subsequent aging of the Zn-Al-Mg alloys at 200° C restores ductility substantially and stabilizes the structures, but strengths are considerably reduced. Combined strength and ductility properties are better for the as-extruded condition than for any heat-treated condition. There is usually little advantage in overall tensile properties from increasing magnesium above 0.1 pct.

Jan 1, 1971

By G. N. Schrauzer

Work has been carried out in the development and testing of carbon monoxide (CO) detection devices which use silica-gel impregnated with metal salts. If carbon monoxide is present, the ?detection gel? (the treated silica-gel) changes from a yellow to a blue-green or blue color. The detection gel "regenerates", i.e., returns to its original yellow color, within 4-24 hours after removal from air containing CO. The detection gel exhibits a threshold of CO response which can be adjusted over a wide range of CO concentrations, typically from 50-500 ppm in air. The preparation of detection gel using salts of palladium, molybdenum and copper is described. Also reported are the results of testing the detection gel&apos;s response to carbon monoxide under varying conditions of temperature and humidity and in the presence of some potentially interfering gases. Low levels of hydrogen sulfide (~ 5 ppm)1 nitrogen dioxide (< 7 ppm), and acetylene (> 200 ppm) were found to affect the detection gel. Temperature and humidity were also found to affect the detection gel&apos;s response. Increasing temperature shortens the gel?s response time while increasing the humidity delays the gel?s response and alters the threshold of the gel. A brief discussion of the further research and development necessary to stabilize the detection gel?s desirable characteristics is included. Descriptions of testing equipment and procedures are covered in detail.

Jan 1, 1978

By M. E. Hawkins

This Bureau of Mines report provides information on all of the 329 proved salt domes in the Gulf Coastal States and offshore area of the United States. It includes specific data related to location, depth to the cap rock and to the salt, storage facilities for LPG, and production of salt, sulfur, petroleum, and rock related to or associated with the dome structure in the subject area. Also included is a brief history of the salt, sulfur, and petroleum industries as related to the salt domes. Gulf Coast salt domes were the scene of the first discovery of a large deposit of rock salt in North America, the birthplace of the Frasch sulfur industry, and the location of the first large oil gushers that ushered in the modern liquid fuel age.

Jan 1, 1966

By M. E. Hawkins

This Bureau of Mines report provides information on all of the 329 proved salt domes in the Gulf Coastal States and offshore area of the United States. It includes specific data related to location, depth to the cap rock and to the salt, storage facilities for LPG, and production of salt, sulfur, petroleum, and rock related to or associated with the dome structure in the subject area. Also included is a brief history of the salt, sulfur, and petroleum industries as related to the salt domes. Gulf Coast salt domes were the scene of the first discovery of a large deposit of rock salt in North America, the birthplace of the Frasch sulfur industry, and the location of the first large oil gushers that ushered in the modern liquid fuel age.

Jan 1, 1966

This report presents the results of a study of Kennecott Copper Corporation?s Chino leaching dump at Santa Rita, N. Mex. The stability studies described herein were performed on only one cross section of the leach dump, utilizing data obtained from drilling, sampling, and testing, which was limited in nature. The first part of the report contains a discussion of site geology and seismicity, pertinent information on the waste material disposal system and leaching method, a discussion of the waste embankment characteristics, a summary of the engineering analyses, and a bibliography. The second part (appendices) contains basic geologic and engineering data supporting the discussions in the first part.

Jan 1, 1974

By John Nagy, Hylton R. Brown, Irving Hartman

"INTRODUCTION The tests described in this publication were planned to provide information on the explosibility of metal-powder dust clouds. This subject has become increasingly important because of the large quantity and variety of metallic powders now used for military and industrial purposes. To provide the increased amounts of metallic powders needed in the manufacture of munitions and to supply the demand created by the rapid growth of powder metallurgy, existing metal-powder plants have been enlarged, production schedules accelerated, and new plants erected. In some cases new methods of producing metal powders have been developed. This increased production and the development of new manufacturing methods have caused an increase in the number of metal-powder fires and explosions, with accompanying heavy loss of life and property. These have emphasized the need for information on methods of providing protection against hazards inherent in the production and handling of powdered metals. This paper gives results of laboratory inflammability and explosibility tests made to April 1, 1943, and is a progress report. Many descriptive details have been omitted purposely; they will supplied in a later publication, expected to be a Bureau of Mines bulletin."

Oct 1, 1943

By Steven W. Schmauch

The U.S. Bureau of Hines conducted e mineral resource survey of approximately 232,000 acres in part of the Humboldt National Forest, Nevada, during 1989. About 7S percent of the study area was covered with mining claims. About 1,800 samples were collected end analyzed for 16 elements. Geologic structure, including thrust faults, is the most important factor in the localization of mineral deposits in the study area. The Independence mine (formerly Jerritt Canyon), Big Springs, and Wood Gulch are the most well known active properties, all developed on large, low-grade, disseminated gold deposits. These deposits have produced almost 3 million ounces of gold and are known to contain more than 8 million ounces of gold. At least 10 barite deposits in the south end of the range have had significant past production and contain 0.2 million tons of resources. Numerous precious and base metal targets have been identified and in some cases quantified during this study.

Jan 1, 1992

Determine the advantages and operational limitations of water-let-assisted cutting used with mining equipment. Approach The Bureau of Mines con-ducted a research study to evaluate water-Jet-assisted cutting both in the laboratory and in underground mines. Earlier research on water-jet-assist was limited to laboratory studies where bit speeds and penetration depths were very low and large cutting force reductions were reported. For the past years, research by the Bureau of Mines and others has been concerned with the application of water-jet-assisted cutting under more realistic mining conditions. Study Results Water-jet-assisted cutting employs a mechanical cut-ting bit combined with a moderate to high-pressure water jet directed just in front of the bit tip to assist in the cutting process. Recent Bureau findings show that the addition of the water jet to the cutting bit can improve cutting in harder materials, significantly reduce respirable dust and bit wear, and increase product size. Some of these findings are presented as follows.

Jan 1, 1987

By N. M. Safaya

Moderate to acute deficiency of plant available phosphorus is very common in western coal mine spoils and topsoils. Although some of the spoils are known to contain seemingly adequate amounts of total phosphorus, the plant available phosphorus is so low that it constitutes a serious plant growth limiting factor in the mined lands. For the revegetation of these spoils, the use of species, varieties and ecotypes exhibiting greater efficiency for P uptake and utilization, or conversely, lesser susceptibility to P deficiency would be highly desirable. To identify such plants, quick and adequate methods of screening germplasm should he available. In the present growth chamber study several plant species were screened using continuous flow culture and spoil culture systems to provide information on their relative susceptibility. In flow cultures, P was maintained at 0.25, 2.5, and 25 moles; while in spoil cultures it was applied at 0, 25, and 75µg/g to a P-deficient spoil. Phosphorus deficiency symptoms appeared in alfalfa cultivars, birdsfoot trefoil, emerald crownvetch and yellow sweetclover within 7-10 days upon transfer of their seedlings to U.25 or 2.5 µM P solutions. Burning bush and Russian thistle, found abundantly as pioneering species on mine spoils, showed no deficiency symptoms; their shoot dry matter yield in the 0.25µM P treatment was 24% and 36%, respectively of their maximum yield obtained with 25 µM P. However, the percent increase in the dry matter yield of legumes with 0.25 µM P ranged from 7-13% over their maximum yield. With the increase in solution P concentration, the root dry weight ratio in the legumes increased from an average of 0.22 to 0.43, while in the weeds from 0.14 to 0.30. The low susceptibility of Russian thistle to P deficiency was also demonstrated in the spoil culture experiment. Legumes showed greater response to P-fertilization on the spoil than did the two weeds. With increasing concentrations of P in the solution, the root weight ratio of all the species decreased. At 25 µM P, weeds invested only 14% of their total dry matter yield in the root fraction, where as legumes and grasses invested as much as 24% and 33% respectively. Weedy species averaged higher P concentrations than the legumes and grasses. The mean P concentrations of alfalfa cultivars were the lowest among legumes. In general, P concentrations increased with the increase in P supply. In the flow culture system, P supply increased the Ca levels of legumes. The mean Mn concentrations were highest in the weedy species. The increases in P supply decreased Zn levels in all of the species. File effects of P fertilization on the tissue concentrations of Mn and Zn in spoil culture were similar to that of flow culture system. From this preliminary study, it may be concluded that the continuous flow culture system is efficient in rapid screening of a large number of species under controlled conditions for their efficiency in adapting to mineral stresses.

Jan 1, 1982

By S. J. Rodgers

This report presents guidelines on methods of dust control in conventional coal mining operations. The normal mining cycle and equipment used in a room and pillar conventional section are described. Main ventilation, section ventilation and face ventilation are discussed in detail. Proper installation of line brattice, maintenance of proper air flows at the face and split ventilation are stressed. The effects of maintaining the end of the line brattice near the face are described. The advantages and disadvantages of blowing and exhausting face ventilation are presented. The use of water sprays on cutter bars and loading machines is described. The design of a nonclogging water spray system developed under a Bureau of Mines contract is presented. Other methods of reducing dust exposure are discussed and include alternative procedures for shot firing and administrative controls.

Jan 1, 1983

By Charles D. Wood

"Selected Topics,? in reviewing the control of emissions from diesel engine powered equipment used in underground mining, explores these fields of interest: hydrogen as fuel; lubricating oil as a source of particulates; applicability of stationary source scrubbers; worldwide diesel exhaust scrubbers; instrumentation technology for measurement of N02; control of emissions through application of sensors and microprocessors; use of fuel additives; technology transfer of marine diesel practice; technology required to use 4-stroke, aftercooled, turbocharged, direct injection engines; oxidation and reduction catalysts for diesel engine exhausts. "Selected Topics? makes recommendations for research and provides a bibliography and lists of references.

Jan 1, 1979

By N. R. Dixon

This report summarizes all work performed under U.S. Bureau of Mines Contract No. J0395028, "Noise Control of Rubber-Tired Front-End Loaders Used in Surface Mining. " Two loaders, a Caterpillar 988 and an International H-400B, were chosen for this program, and the noise sources and acoustic paths that contribute to the operator&apos;s noise exposure were identified. Retrofit noise control treatments were designed and installed on these loaders, and noise reductions of more than 10 dBA at the operator position were achieved on both machines. The retrofit packages are low cost and have been field tested in two mines for more than two years. The results of the program were communicated to the mining industry through a series of noise control workshops and a field manual. The workshops were given in nine states across the U.S. and more than 440 manuals were distributed An audio/visual slide presentation was also developed which the program.

Jan 1, 1983

By Terry S. Cory

This report covers magnetic field strength measurements vs range and frequency In low-medium coal mines. Both quasi-conductor-free and conductor-proximity areas were Investigated. The program covered 5 mines, 4 seams, 6 measurement sets, and 3 geographic areas, The results have been summarized In terms of maximum communication range expected per seam and noise condition. Scatter gain Is further explored as a simple measure of energy coupled to conductors.

Jan 1, 1978