Search Documents

By Philip Thompson

A part of the Bureau of Mines mission is to help improve the Nation's mineral posture by providing the technology for utilizing low-grade ores. In this regard, laboratory testing by the Bureau of Mines has shown that the removal of insoluble slimes using selective flocculation and flotation is a viable method for treating low-grade potash ores that have a high content of water-insoluble impurities. Results indicated that over 82 percent of the insoluble slimes could be removed from sylvinite ore containing 5 percent water insolubles and 13 percent K20 by using nonionic or cationic polyacrylamide flocculants and cationic, anionic, and/or nonionic collectors. Subsequent potash flotation recovered 87 percent of the potash in rougher concentrates containing 57 percent K2O. Sizing and cleaner flotation of the rougher concentrates upgraded the products to 60 percent K2O. Filtration of the water-leached insoluble-slimes flotation concentrates on a bed consisting of leached insoluble-slimes concentrate mixed with potash flotation tailings recovered 80 percent of the brine. Filtration rates using the mixed bed were nine times faster than filtration rates obtained when the insoluble-slimes flotation concentrates were filtered separately.

Jan 1, 1979

By Michael Gibbons

A method of monitoring roof stability in underground mines by detecting the changes in resistivity of roof material was tested. The device built by the USBM was tested over a 16 month period at the White Pine Copper Mine in White Pine, Michigan. Three falls of ground were monitored by means of as many as 11 sensors. Data indicate a correlation between changes in resistivity and impending structural failure. Problems were encountered with the high roof electrode impedance in the winter and spring due to the drying out of the roof material. Difficulties also developed in obtaining a permanent bond between the roof rock, the conductive epoxy and the electrode plate. Some data were lost due to timer and fuse problems within the unit. These were eventually rectified.

Jan 1, 1979

By Loren R. Anderson

This is an Appendix of Volume I. It contains the results of the electric cone penetrometer soundings from the first phase of the testing program.

Jan 1, 1982

By Nicholas Kyriazi

A joint effort by the U.S. Bureau of Mines (USBM) and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CPR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fourth phase of testing from 1989 to 1993. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except units with manufacturing defects. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. In addition, some apparatus collected for this study had not been returned to the manufacturer in a recall effort for correction of a manufacturing defect. In both cases, the apparatus would have presented problems in emergency use. Recommendations include improved training in inspection procedures and better enforcement of recall notices.

Jan 1, 2010

By B. W. Jong

As part of the Bureau of Mines program to develop substitutes for critical and strategic materials for metallurgical applications, the Tuscaloosa Research Center has evaluated the effect of additives and starting materials on the sintering and strength properties of sialon (silicon-aluminum-oxynitride) compositions fabricated by conventional pressing and sintering techniques. Sintering and MOR (modulus of rupture) data were developed for sialon compositions produced from three components, Si3N4, A1203, and AIN. When doped with Y203 to aid in sintering, the highest MOR values were obtained with compositions containing between 20 and 30 mole-pet (A1203 + AIN). The effect of the crystalline phase of the Si3N4 and Al203 used in the three-component system on MOR also was investigated. Alpha-Si3N4 and ?-A1203 were found to be the best starting materials. A sialon composed of 67.4 mole-pct a-Si3N4 plus 32.6 mole-pct (?-AI203 + AIN), doped with 5 wt pct Y203, had MOR values at 25°, 1,200°, and 1,400° C of 40,300, 40,300, and 31,100 psi, respectively. Samples of this composition doped with Gd203, MgO, Zr02, and ZrSi04 also were evaluated. The ZrSi04-doped sialon had higher MOR values than Gd203-, MgO-, and Zr02-doped materials but lower MOR values than the Y203-doped sialon. The MOR values of ZrSi04-doped sialons were 25,000 and 25,900 psi, respectively, at 25° and 1,400° C.

Jan 1, 1981

By N. A. Gokcen

In this Bureau of Mines report, appropriate equations correlating the activity of water with the activities of electrolytes in binary and multicomponent solutions have been derived for computer calculation. It was found that the half-integer power series are far superior to the integer power series, for both types of series having the same number of terms. The pro-posed method of calculation is capable of accurately yielding the activities of all components from the measurements of the activity of a single component at various concentrations. This method replaces the cumbersome and objection-able method of graphical integration of the Gibbs-Duhem equation. Two novel methods are proposed for determination of activities of electrolyte solutions important in hydrometallurgy; (1) Water vapor pressure measurement by differential pressure transducers having an accuracy of 0.001 pet, and (2) transpiration method with an inert gas bubbled through concentrated solutions followed by the analysis of the evaporated and redissolved electrolytes with specific ion electrodes having a sensitivity of ±10-10 molal. The first method is suitable for nonvolatile electrolytes, and the second, for volatile electrolytes such as hydrogen halides, HN03, H2S03, etc. The existing methods of estimation of ionic activities have been surveyed, and the best method has been selected, discussed, and summarized.

Jan 1, 1979

By Robert L. Anderson

A shaft or slope bottom is that portion of a mine that is contiguous to the bottom of the main hoisting shaft or slope. It includes the terminal tracks for loaded-and empty-car storage, locomotive run-arounds, locomotive shops, charging stalls, supply rooms, pump rooms, waiting rooms, and offices for dispatcher, weighmen, and foremen. This paper will deal principally with the arrangement of tracks and the handling of cars on the bottom, but includes other data that may be affected, directly or indirectly, by the bottom lay-out. All of the mines discussed are being operated in comparatively level coal seams.

Jan 1, 1937

By W. M. Deaton

The Keyes Helium Plant of the Federal Bureau of Mines was constructed under an expedited schedule, to supply the urgent and growing demand for helium in atomic energy, missiles, aerology, space exploration, shielded-arc welding, and low-temperature research. Construction began in December 1958 and ended in August 1959. The plant, near Keyes, Okla., processes 2 percent helium-bearing natural gas from the Keyes gasfield. In 1960 the plant produced and shipped 263 million cubic feet of helium (equivalent to an annual rate of 290 million cubic feet). Production cost was $9.11 a thousand cubic feet of helium. A low-temperature process involving two steps is used; the first separates a crude-helium product from the natural gas at about -250° F. and 225 pounds per square inch gage (p.s.i.g.); and the second purifies the crude helium to a high-purity product (Grade-A helium, 99.995 percent helium) at about -320° F. and 2,750 p.s.i.g.

Jan 1, 1961

By L. R. Burdick, R. Wiggers, J. F. Berkley

"INTRODUCTION On February 23, 1944, Solid Fuels Administrator Harold L. Ickes stated that the existing fuel shortage made it necessary to utilize a great surplus of freshly mined anthracite ranging in size from Barley (No. 3 Buckwheat) downward through the smaller sizes. As a part of the program to increase the use of such coal, field trials of mixtures of bituminous slack coal and anthracite Barley were made on industrial-size stokers at many fuel-burning plants. The following covers the test information it was possible to accu-mulate during the work of initiating the use of these mixtures at the plants.SUMMARY AND CONCLUSIONSField tests of various mixtures of bituminous slack coal and anthracite Barley on industrial-type stokers show that the use of such mixtures is very practicable and that it is possible to change and usually to adjust to an improved condition the characteristics of a fuel bed of eastern bituminous slack coal by the addition of proper amounts of anthracite. The improved uniformity of the fuel bed of single-retort stokers makes possible less manual attention to the bed. Air flow through the fuel bed is affected.Smoke is decreased. In general, the fly ash and also the unburned combustible in the fly ash and refuse are increased. Clinkering in the fuel bed is generally lessened. The peak-load carrying capacity of the stoker is definitely affected, usually adversely for the higher percentages of anthracite."

May 1, 1946

By John W. Cole

The Butte district has been the principal producer of metallurgical-grade manganese in the United States since World War I. Manganese dioxide nodules are produced from rhodochrosite ore by concentrating the rhodochrosite and roasting the concentrate in rotary "cement-type" kilns. The Anaconda Copper Mining Co. is the only producer at present. Under the stimulus of a purchasing program administered by Metals Reserve Company during World War II, however, several independently owned or operated mines (including the Norwich) produced manganese carbonate ore. These mines were examined in Juno 1949 by John W. Taber, mining engineer, Bureau of Mines. A core-drilling program to develop ore in the Norwich mine was recommended and approved. drilling was completed early in 1950. This report gives factual data obtained.

Jan 1, 1951

By Wesley Holmes

Concentrating, nodulizing, and smelting studies were conducted at the Albany Metallurgy Research Center of the Bureau of Mines to determine whether (1) western iron ores of the type found in the Carter Greek deposit near Dillon, Mont., could be utilized; (2) concentrates of acceptable grade with good iron recovery could be attained by wet-magnetic beneficiation; (3) nodulized concentrates could be smelted with reductants readily available in Montana; (4) iron concentrates could be smelted without prior agglomeration; and (5) high-purity iron could be produced directly from high-grade concentrates, Three small samples and two tonnage samples from the Carter Creek deposit were uniform in chemical composition, and their iron content averaged about 31 percent. They were found to be banded gneisses, and magnetite was the principal iron-bearing mineral.

Jan 1, 1962

By John K. Alley, Robert C. Johnson

The primary objective of the research was to grow aluminum borate whiskers or fibers and to determine their properties . Molten salt bath and vapor deposition methods were used for synthesis . Whiskers exceeding 25 mm in length were grown . The best results were obtained by vapor deposition and most of the data presented were determined on whiskers produced by this method of synthesis . Three different aluminum borate compositions ( 4.8A1203 B₂03 , 3.8A1203 B203 , and 2.5A120, B203 ) were identified by X- ray and chemical analyses . The aluminum borates 4.8A1203 B20, X- ray diffraction pattern was indexed . Optical data were obtained on the three aluminum borates . In addition the following whisker properties and growth factors were determined : ideal atmospheric dewpoint for vapor deposition method , near 65 ° F ; temperature range of whisker formation , 1,000 ° to 1,400 ° C for the molten bath method of synthesis , > 1,000 ° to < 1,400 ° C for the vapor deposition method ; whisker growth rates by the vapor deposition method , maximum 12 mm per hour ; raw material vaporization , 50 to 60 percent of the fluoride lost in 1 hour ; tensile strength , maximum obtained 174,162 psi ; melting points , ranged from 1,675 ° to 1,795 ° C.

Jan 1, 1965

By Walter Kawa

The hydrogenation of phenyl ether, benzyl ether, and phenyl sulfide in the presence of iron catalysts was studied by the Bureau of Mines to gain a better understanding of the role of iron catalysts in the hydrogenation of coal. The carbon-oxygen and carbon-sulfur bonds in these compounds may be similar to some of the carbon-oxygen and carbon-sulfur bonds in coal which react during the early stages of liquefaction by hydrogenation. Experiments were made in batch autoclaves for 4 hours; hydrogen was at a pressure of about 540 atmospheres. In the hydrogenation of phenyl ether at 400° C, metallic iron catalyzed both hydrogenolysis (splitting-hydrogenation) and nuclear hydrogenation (addition of hydrogen to aromatic rings) reactions, Products were principally benzene and cyclohexane. The activity of metallic iron was decreased by adding carbon monoxide or a reactive sulfur-containing organic compound. Ferrous sulfide catalyzed the conversion of phenyl ether to benzene, phenol, and small amounts of cyclohexane. Hydrogenolysis of benzyl ether was catalyzed by metallic iron and to a lesser extent, by ferrous sulfide at 250° C. No nuclear hydrogenation was observed with either catalyst. Conversion of phenyl sulfide to benzene was nearly quantitative in experiments made at 250° C with equimolar quantities of phenyl sulfide and metallic iron or iron as ferric oxide. Conversions of metallic iron and ferric oxide to ferrous sulfide were nearly stoichiometric. No reaction of phenyl sulfide occurred in the presence of ferric oxide and water, and very little occurred in the presence of metallic iron and water. Ferrous sulfide also catalyzed the hydrogenolysis of phenyl sulfide to benzene, but conversion was lower than in experiments with metallic iron or ferric oxide. The activity of ferrous sulfide was increased by adding water and decreased by adding hydrogen sulfide. The results of this study suggest that ferrous sulfide is an active form of iron when iron is used as a catalyst for the hydrogenation of coal.

Jan 1, 1963

By T. Whitrnoyer, J. Sneckenberger

"The acOustic impedances of seven rat lungs were measured at frequencies between 100 and 6400 Hz. Rats were divided into two groups: a silica exposed group (N=3) and a control group (N=4). The silica exposed group was injected intratracheally with silica solution. Three of the control group were intratracheallyinjected with saline. Between four and six weeks after theinjections, all lungs were excised and degassed. Lungs were,suspended in a pressure Chamber, with the trachea canula attached to the end Of a tapered impedance tube. The lungs were subjected to transpulmonary pressures between -30 cm H2O and 6 cm H2O to simulate deflation and inflation. With transpulmonary pressure being held constant, the impedance tube was excited with random noise. A dual channel analyzer calculated H12(f), the transfer function between the two microphones. This function was used to calculate the lung's impedance at that pressure. The impedance magnitude spectra of both groups typically had peaks at 2000,3500, and 5500 Hz. Statistically significant differences. (90%confidence level or greater) between the two groups occur at the 3500 Hz peak at transpulmonary pressures of 20, 8, 6, 4, and 2 cm of H2O. This fact seems to confirm that this method can detect. lung disease. Further research will indicate whether this method will be able to detect the onset Of coal worker's pneumoconiosis.INTRODUCTIONOne of the first studies of impedance Of the human lung were conducted by DuBois et al.[2] using the forced OscillatiOn technique. This technique, however, was limited to frequencies below 30 Hz. Further studies by Van Den Berg [6] revealed thatthe lung reflected higher frequency sounds (100-10,000 Hz), instead Of behaving as an anechoic termination. This discovery has lead to several studies of the acoustical properties of both human and animal lungs at high frequencies [3,4,5]."

Jan 1, 1988

By J. M. Gomes

The Bureau of Mines, as part of an effort to maximize minerals and metals recovery from domestic resources, has investigated the feasibility of recovering heavy minerals as byproducts from sand and gravel, placer gold, and industrial mineral operations in northern California. Sand samples from about 50 locations were treated by gravity separation to yield heavy-mineral concentrates (black sands). Mineral compositions of the concentrates were determined by chemical analysis and mineralogical examination. Individual zircon, ilmenite, magnetite, platinum-group metals, thoria, and silica products were prepared from heavy-mineral concentrates by selective separation using low-and high-intensity magnetic, high-tension, and flotation equipment.

Jan 1, 1979

By W. C. Holliman

This report on the characteristics of commercial aviation gasolines is one of a series of such reports. It presents compilations of&apos; inspection data furnished on their products by 15 manufacturers of commercial grades of aviation gasoline and special data obtained in Bureau of Mines laboratories on 68 samples of these gasolines. Data are presented for 18 samples of grade 80, 20 of grade 91/98, 21 of grade100/130, and 9 of grade 115/145 aviation fuels. The gasolines are designated January 1948 production, although some of the samples actually were produced at a later date.

Jan 1, 1948

By Robert E. Barieau

This report gives the principles of the method used by the Helium Research Center of the Bureau of Mines when solving nonlinear-regression problems and contains the mathematical equations necessary to accomplish the following objectives: the evaluation of the parameters in such a way that the sum of the weighted squares of the residuals of an experimental observable is a true minimum, regardless of the functional relationship between the variables and these parameters; and the evaluation of all variances and covariances of the parameters by means of the usual approximation of the law for the propagation of errors.

Jan 1, 1967

By N. Greninger

The Bureau of Mines examined the possibility of a seasonal variation of respirable dust concentration in U.S. coal mines. The first step was to review company and MSHA-inspector dust samples that had been collected during the past several years in 14 selected mines for compliance purposes. Results indicated severe scatter in data; most standard deviations of the dust concentrations measured in winter and summer months were comparable in magnitude with the mean values of dust concentrations for the seasons. Therefore, a detailed statistical analysis was conducted. At the 90% confidence level, the company samples of three mines had winter means 0.15 to 0.54 mg/m3 higher than the summer means; six mines had negligible seasonal variations; and five mines had winter means that ranged from higher to lower than the summer means. Inspector data, however, were too sparse for analysis. In view of both the low frequency of occurrence of a seasonal effect and its wide scatter in several of the mines, the study was ended with the conclusion that seasonal varia-tion in respirable dust levels, in general, is an insignificant factor.

Jan 1, 1986

By L. B. Pankratz, R. Barany, W. W. Weller

Experimental determinations were made of the heats of formation at 298.15 ° K of cuprous ferrite and cupric ferrite ; the heat capacity of cuprous ferrite was measured over the temperature range from 50 ° to 298 ° K and the entropy at 298.15 ° K was evaluated ; the heat contents of cuprous ferrite and cupric ferrite above 298.15 ° K were measured to 1,500 ° K and 1,100 ° K , respectively . These thermodynamic values were combined with other pertinent data to obtain heat and free energy of formation values at high temperatures . The stability of the two ferrites with respect to their constituent oxides is discussed . Thermodynamic values are included for the decomposition of cupric ferrite to form cuprous ferrite , magnetite , and oxygen .

Jan 1, 1964

By Franklin D. Cooper

This Bureau of Mines study reviews current and proposed methods of extracting copper from sub-mill-grade ore by leaching. The amount of copper produced by hydrometallurgy has increased dramatically in recent years and will probably be about 200,000 tons per year by 1970.

Jan 1, 1968