Search Documents

A study was conducted by the Bureau of Mines to evaluate natural gas as an automotive fuel and to provide guidelines for optimum engine adjustments for low exhaust emissions. The study was conducted using a single-cylinder engine, a multicylinder engine, and a total of eight vehicles. Results from single-cylinder engine tests showed that the light-load, lean-limit misfire region for natural gas begins at an air-fuel ratio between 150 and 160 pct of stoichiometric. Changes in ignition timing significantly influenced emissions of nitrogen oxides and hydrocarbons, but had little effect on carbon monoxide emission. Low emissions can be achieved with current-design engines by adjustment of engine parameters, but only with heavy penalty to engine performance. Emissions from vehicles fueled with natural gas are virtually unaffected by ambient temperature change within the range 20° to 100° F. The organic emissions from engines fueled with natural gas were estimated to be 22 to 25 pct as reactive as the emissions produced using gasoline. Levels of exhaust emissions from vehicles fueled with natural gas were unchanged over 10,000 miles of normal driving.

Jan 1, 1973

By G. L. Oldright

This paper is the twelfth of a series on smelting in the lead blast furnace and the fifth dealing with blast-furnace gases. It was noted in Report of Investigations 2957 that the gases evolved from the top of the lead blast furnace at Tooele were similar in composition to those from the top of an iron blast furnace. It was noted in Report of Investigations 3095 that at Kellogg, where a smaller percentage of coke on charge and shorter stock column were employed, the gases evolved were much less reducing. At times there was a considerable amount of oxygen in the top gases at the second plant. More SO2 was also evolved from sulphides in the charge. Then operations were conducted as at Kellogg, the gases were alternately reducing and oxidizing. This paper deals with the gases evolved in smelting a charge containing more zinc than at either of the other two plants with about the same amount of coke as was used at Kellogg,: To compare other factors influencing the composition of the gases, it may be noted that at Tooele the approximate height of the charge column was 15 feet, at Kellogg 9 feet and at Trail 13 feet. The furnaces have about the -same cross-sectional area- tog. The furnaces at Tooele are about 6 inches wider at the tuyeres, being 54 inches wide against 48 for the other two plants. At Tooele and Kellogg the furnaces are fed at the top from bottom-dump cars. At Trail the charges are dumped from Decauville cars (bottom cars which dump when tilted), which run on tracks placed on both sides of the blast furnaces. The hoods through which the waste gases are conducted are directly above the shafts of the furnaces. The flues for removing the effluent gases lead off from under the charge floor at Tooele and Kellogg. (Charging and distribution of the feed in the furnace covered later in a rate paper of series.)

Jan 1, 1934

By Manuel Gomez

This report presents experimental work conducted on a number of coals found within the boundaries of the Missouri River Basin, which were, to an extent, a selection of coals typical of that region. In the min, the laboratory work falls into three general classifications: (1) Laboratory distillation assay of coal to establish yields on carbonization; (2) chemical analyses of the coal samples before drying or carbonization; and (3) chemical analyses of the products of carbonization. It will be seen in the following discussion that these data derived from the small-scale laboratory apparatus are useful in predicting yields from pilot plants or industrial units. Coal is produced in about 48 general areas or mining fields in the Western States, of which approximately 18 fall within the limits of the Missouri Basin.3/ Beginning with the Northern Colorado field, through the Central and Western Wyoming fields, the coal is principally bituminous and subbituminous rank. The western Montana coals are also of these ranks. Progressing northeast from central Wyoming the coal decreases in rank, as shown by the subbituminous C coals of the Gillette field in northern Wyoming and the lignites of eastern Montana and North Dakota.

Jan 1, 1953

By John A. Breslin

Size distributions and concentrations of particulates emitted from diesel engine exhausts were measured with cascade impactors. Samples were taken from the exhaust of two types of engines using three types of fuel and operating under five different engine speed and load conditions. The measured mass median diameters of the diesel particulates were typically about 0.3 um. There was no significant difference in mass median diameter between engines or fuels and only a slight dependence on operating mode. Concentration measurements ranged from 14.2 to 250.9 mg/cu m, and calculated mass outputs, from 52 to 3,443 mg/min. Significant differences in mass output were found between engines, fuels, and especially between different operating modes. The quantity of clean dilution air that would be required to reduce the particulate mass concentration below the 2.0 mg/cu m respirable dust standard for coal mines was greater than the dilution air required to meet the standards for noxious gases for both engines tested.

Jan 1, 1976

By Gary A. Kingston

Domestic nickel resources are costed to develop a contingency supply curve of U.S. nickel availability at various costs. It is estimated that 4.3 billion pounds of nickel is potentially recoverable from 698 million tons of ore at prices ranging up to $6.36 per pound of nickel. Over 95 percent of the total is estimated to be available at a price of less than $4.00 per pound.

Jan 1, 1970

By R. S. Fowkes

The Bureau of Mines constructed a fully automated pilot plant facility to study the hydraulic transportation of solids through a lock hopper feeder system. An equation for the energy requirements to transport coarse solids hydraulically proved applicable to this system. Optimum velocities were obtained for limestone, mine refuse, and bituminous coal. The experimental data, calculations, and graphs show the effect of velocity, specific gravity, and solids concentration on head loss and power requirements. Other data were obtained and evaluated to determine the effect of particle size on head loss. Results also are given for (a) tests using friction reducing polymers; (b) tests using seven test sections of steel alloy pipe to determine their wear characteristics; (c) tests to determine spatial segregation of moving particles; and (d) tests to determine the effect of shape, size, and specific gravity on particle velocity in a horizontal pipeline. The lock hopper feeder system was found practical for continuous hydraulic transportation of the material types and size ranges tested.

Jan 1, 1969

By Dougherty. E. Y., S. W. Zoldok, John W. Cole

"INTRODUCTION During its wartime program of exploration for minerals essential to the national economy, the Bureau of Mines was instructed to investigate sources of raw materials used in the manufacture of iron and steel. As a part of this investigation, some work was done on the iron deposits on the Neutral and Aztec claims on Buckhorn Mountain Canogan County, Washington, which was designed chiefly to indicate the nature and behavior of the ore deposits below the surface exposures. Diamond drilling was started in June and completed in July 1945. Preliminary laboratory tests on iron, ore from Buckhorn Mountain were completed during the fall and winter of 1945. This report presents the data obtained from the investigation.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final re¬port. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Apr 1, 1947

By Charles Will Wright

The purpose of this paper is to present briefly certain preliminary results of the study of mining methods by the United States Bureau of Mines; to show the relative importance of each method in terms of tonnages mined and man-hours consumed; to give to the mining engineers and particularly to the young student of mining a better understanding of the principal mining methods; and to indicate changes now in progress and to present suggestions for improvements in the art of mining. Questions of mine development and details of underground practice such as drilling and blasting, loading, hauling, hoisting, ventilating, pay systems and mine management are omitted, as these have been or will be discussed in other bureau publications.

Jan 1, 1931

By C. J. Cohen, L. A. Dahners

"SUMMARYA method has been developed for surveying, drill holes without lowering into the hole any surveying equipment other than an etch tube. The orientation of the rods at the collar of the hole is maintained as the etch tube is lowered. The attitude of the etch ellipse in depth with respect to the rod orientation at the collar can then be observed. This relationship permits the bearing of the hole in depth to he calculated. The rod orientation is maintained during the lowering by means of a pair of alinement clamps. One clamp is fastened to the top of each rod as the rod is coupled and is removed when the alinement has been transferred to the other clamp at the top of the next succeeding rod. A particular advantage of this survey technique is that surveys can be readily made in magnetic country rock.PRINCIPLE OF THE TECHNIQUEAn axial lamina of the column of drill roes is the lamina in which one fiber would be the centerline of the rods. In the new survey technique, the rods are fed into the hole in such a manner that the axial lamina of each successive rod maintains its position at the collar of the hole. In depth, as the rods bend in following the drill hole, the axial laminae also bend. The lamina that was originally vertical will, in general, be tilted away from the vertical. The trace of this lamina is marked on the glass etch tube before the tube is lowered in the hole. The axial lamina that becomes vertical at the survey station is recognized as that axial lamina which contains the long axis of the etch ellipse. The angle between the lamina originally vertical and the lamina vertical at the survey station is thus measurable. When the vertical axial lamina at one survey station has been determined by the etch ellipse at that station, angle R between this lamina and the vertical axial lamina at the next survey station becomes measurable also. By moans of angle R, and dip angles D1 and D2 at the two stations, the change in bearing (z) of the drill hole between the two stations can be calculated."

Aug 1, 1944

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making; and (3) to upgrade marginal coals through effective preparation. This is the second7j of a series of reports giving the results of studies by counties under part (1) of the investigation. This report covers Indiana County, Pa., which comprises parts of the Smicksburg, Punxsutawney, Elders Ridge, Indiana, Barnesboro, Latrobe, New Florence, and Johnstown Quadrangles. (See fig. 1.) A base map for each bed in each Quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1950

By Scott W. Hazen, George W. Gladfelter

This report presents the results of an initial investigation into some problems resulting from the use of assays representing unequal sample interval lengths and the use of the weighted average grade of ore in evaluating bedded mineral deposits . A mathematical proof and examples are given to show that the unweighted and weighted assay averages are equivalent when there is no correlation between assay value and sample interval length but that these averages are different when there is correlation between assay value and sample interval length . The amount of this difference between estimates is a function of the degree of correlation . One set of sample and assay data , based on 11 stratigraphic sections of the Phosphoria formation in Idaho , indicates that the relationship between the amount of difference between estimates and the correlation factor is approximately linear . If this correlation relationship can be established , within acceptable limits of precision , as a consistent attribute of deposits , the estimate of weighted average grade of ore could be predicted directly from the unweighted estimate of grade of ore by using the relationship as a prediction factor . Randomness tests on the sample and assay data from the Phosphoria formation , using the mean - square - successive - difference method , indicate that correlation between assay value and sample interval length ( each sample interval length represents an individual bed or stratum of the formation ) , apparently has little effect on the independence between successive assays , between successive sample interval lengths , and between the products of assays and sample interval lengths . Therefore , these data can be analyzed statistically as long as the original sample sections have been selected at random for sampling .

Jan 1, 1964

By H. F. Weaver

The 19th National First-Aid and Mine Rescue Contest was held in the Civic Center, Charleston, w. Va., on October 2, 3, and 4, 1961. The meet was sponsored by the Bureau of Mines and the Joseph A. Holmes Safety Association, in cooperation with State mine inspection agencies, management and labor of the mineral extractive industries, and other groups interested in safety. The Arrangements Committee, as authorized by the General Committee, made the necessary arrangements for conducting the 1961 contest. Members of the Arrangements Committee were: George Trevorrow (chairman), Bituminous Coal Operators' Association; James B. Benson, Southern Coal Producers' Association; Charles Ferguson, United Mine Workers of America; Harry Gandy, Jr., National Coal Association; and James Westfield, Bureau of Mines.

Jan 1, 1962

By J. W. Miller

Depletion of coals most suitable for metallurgical fuel has nude necessary a general survey of coking-coal reserves in the United States. These investigations were begun in 1948 at the joint request of the Munitions Board, Department of Defense, and a number of coal companies. This report, which is one of a series, by counties, describes the preparation characteristics of the coals of Letcher County, Icy. From these data it is possible to determine: (a) Which coals either as mined or after beneficiation by conventional preparation are suitable under present standards for producing metallurgical coke, (b) which coals require special and more intensive treatment in preparation than is now practiced, and, (c) which coals cannot be upgraded by known commercial preparation methods to metallurgical fuel standards now accepted.

Jan 1, 1955

By J. B. Clemmer

Fluorspar is one of the most important nonmetallic minerals and is used extensively in the metallurgical, ceramic, cement, and chemical industries. The steel industry consumes most of it, but as the Mineral is the chief source of fluorine, it is becoming increasingly valuable to the chemical industry in the production of fluorine compounds. The development of nontoxic organic fluorides for use as refrigerants in mechanical refrigeration and air-conditioning units illustrates the increasing use of fluorspar in the chemical industry. Most domestic flurospar comes from deposits in the Illinois-Kentucky district, which centers around Rosiclare, Ill. About a dozen companies operate in the district, which comprises parts of Pope and Hardin Counties in southern Illinois and Crittenden, Livingston, and Caldrell Counties in western Kentucky. According to the latest available statistics, this district supplied 165,960 short tons of fluorspar in 1937, compared with the total domestic production of 151,230 tons. Imports totaled 37,063 tons.

Jan 1, 1939

By G. L. Oldright

The data presented in this paper were collected et the smelter of the Consolidated Mining A Smelting Co. of Canada, Limited, Trail (Tadanac), British Columbia, through the courtesy of S. G. Blaylock, vice president and general manager; James Buchanan, smelter superintendent, George Murray, assistant smelter superintendent; and the staff members listed in Paper XI, Report of Investigations 3243. INTRODUCTION This paper is the twelfth of a series on smelting in the lead blast furnace and the fifth4 dealing with blast-furnace gases.

Jan 1, 1934

By Richard O. Kneisley

An empirical method, based on U. S. Bureau of Mines field studies in several Western U.S. coal mines, is presented for sizing gate road yield pillars. Discriminant analysis was used to generate functions separating successful from unsuccessful case studies. These functions relate the pillar width-height and extraction ratios and a pillar development factor to the Coal Mine Roof Rating System (CMRR), and are assumed to establish three criteria that other entry systems, under similar conditions, must satisfy. A program, Pillar Sizer, from user-provided inputs, generates a range of pillar sizes that meets the proposed criteria. Although the analysis is based on a sample consisting primarily of two-entry systems, the derived expressions generate pillar sizes closely agreeing with observed, two-entry and three-entry in situ pillars. It is concluded that the proposed approach should assist mine operators estimate entry system yield pillar dimensions.

Jan 1, 2010

By G. S. Scott, G. W. Jones

"INTRODUCTION An important phase of the accident-preventing program of the Bureau Mines is the determination of the explosion hazards of various combustible gases, vapors, and liquids encountered in mining and allied industries and the development of methods of eliminating or mitigating them.Recently, isobutane has become a commercially important raw material in the production of aviation gasoline by the alkylation process. 4/ in which isoparaffins are combined with olefins to give higher molecular weight compounds of branched-chain structure.Because of the anticipated commercial importance of isobutane in industry, it has been deemed necessary to study and determine its general explosion haz¬ards. This report gives its limits of inflammability, minimum ignition temper¬atures, and the amounts of nitrogen and carbon dioxide required to render isobutane-air mixtures noninflammable."

Jun 1, 1947

By P. M. Brown

The Bureau of Mines is investigating a dewatering technique for coal-clay waste that uses a flocculant, polyethylene oxide (PEO). This flocculant forms strong stable flocs that can be dewatered on a static screen. A field test unit (FTU) using this technique was operated at approximately 400 gal/min, using a waste stream from the flotation circuit of a coal preparation plant. Consolidated coal-clay material con-taining 55 to 60 pct solids was produced when the flotation circuit slurries of 2.7 to 8 pct solids were treated with 0.1 to 0.3 Ib PEO per ton of solids. The FTU was also operated at 64.5 and 87.5 gal/min using a portion of the underflow slurry from the preparation plant's thickener. Consolidated coal-clay material containing 55 to 60 pct solids was produced when the thickener underflow slurries of 19 to 24 pct solids were treated with 0.08 to 0.2 Ib PEO per ton of solids. PED-treated materials continued to dewater when placed in a pit.

Jan 1, 1983

By Christopher D. Risbrudt

In this comprehensive study of the use of wood products in coal mining, a sample of over 220 mines provided data by questionnaire. Wood use per ton of underground coal was found to vary substantially by mining process and region. In the Eastern Coal region, 1.6 board feet of wood was used per ton of coal, wel above the 0.6 board feet usage per ton in the West. The kind of timber used varied also by Region. Hardwood use is about 40 times greater than softwood in the Eastern Region. There, hardwoods are plentiful, relatively cheap and strong. In the West where softwood forests predominate, softwoods were 2-1/2 times more common in mine wood use than hardwoods. Nearly 80 percent of the wood used in underground coal mines is used in cross bars and props. Nearly 54 million cubic feet of wood products were used in coal mining in the sample year 1979; about twice as much going to underground mines as surface mines. Wood requirements for mining were projected to 2030 for a range of three oil price scenarios. Much greater wood use will be required for greater coal output.

Jan 1, 1982

By Gary E. Sherman

To aid the U.S. Army Corps of Engineers In their Resource Development Navigation Study, the U.S. Bureau of Mines (Bureau) examined the potential for mineral development near ten Alaska port sites. This report presents the results for the first three sites: Bethel, Kivalina (Red Dog), and Omalik Lagoon. The mineral deposits near Bethel are primarily gold and mercury; the nearest deposit being 55 mites away. Because of the expense of constructing and maintaining a road over the poorly drained lowlands, the potential of Bethel as a port site in the near-term is considered to be low. The Kivalina site currently serves the Red Dog mine and has the potential to handle material for similar deposits in the area. Results from a lead-zinc mine model indicate that potential for additional mine development exists in the area. Coal is the major deposit type found near the Omalik Lagoon site. Due to environmental constraints, development of a large-scale mine producing coal for export is considered unlikely. A small-scale coal mine model was used to examine the feasibility of producing coal for regional use. This alternative may be feasible but would require conversion of heating/generating equipment in the area.

Jan 1, 2011