Search Documents

By T. Estelle Gardner

Heat-capacity measurements were made over the range 8° to 350° K on beryllium sulfate dihydrate and beryllium sulfate tetrahydrate using an adiabatic calorimeter. No anomalies were noted in the curve for either compound. Smooth values of heat capacity, entropy, enthalpy function, and free-energy function were calculated from the heat-capacity data at 10° K intervals and at 273.15° and 298.15° K. The entropy values calculated at 298.15° K were 39.01 ± 0.12 entropy units (eu) for the dihydrate and 55.68 ± 0.17 eu for the tetrahydrate.

Jan 1, 1967

By Fred D. Wright

A compressor and utility station, which is believed to be one of the largest mobile units of this type ever constructed, was placed in operation at the Bureau of Mines experimental oil-shale mine near Rifle, Colo., during. 1949. This mobile unit mounts two 770-cubic-feet-per-minute air compressors, a 2,500-gallon water tank, and a 200-cubic-foot air receiver. The mobile base of the unit is a 30-ton trailer 30-feet long and 12-feet wide. Prior to the construction of this unit, compressed air was supplied to underground workings through pipe lines connecting with a stationary compressor plant on the surface. The power consumed in supplying compressed air to underground drilling crews was 0.531 kw.-hr. per ton of shale broken. Use of the mobile unit has cut this figure to 0.421 kw.-hr. per ton of shale broken and, more important, has eliminated the cost of installing and maintaining underground air and water lines.

Jan 1, 1950

By S. H. Ash

The United States Bureau of Mines has published relatively little on the flooding and unwatering of coal and metal mines. Bulletin 229, Fifty-Nine Coal-Mine Fires, published in 1927, contains several instances of the flooding of mines or sections thereof to extinguish fires but does not describe their unwatering. Report of Investigations 2649, Explosion Hazards Incidental to Unwatering Coal Mines, published in 1924, warned against the possibility of gas accumulations in flooded mines and indicated the precautions to be taken. Report of Investigations 2255, An Unusual Hazard in Reopening Long-Flooded Timbered Metal Mines, published in 1921, told of methane being pocketed and the danger thereof. The flooding of mines originates in many ways. At some mines flooding followed reopening after what was thought to be permanent abandonment; also, explosions have caused some mines to be flooded. Extinguishing fires, accidental encountering of underground streams or flooded old workings, and caves of strata admitting water from underground workings, water-bearing strata, or surface accumulations have also flooded all or parts of mines. Unfortunately, un watering often necessitates much study and causes apprehension largely because experiences in similar situations are not generally known, as few descriptions of successful or unsuccessful methods are available. The job has sometimes been contracted for outside the local management involved and has become a matter of record for the contractor only. As the cost-plus contract system often employed in the past is now known to be expensive, careful managements elect to handle the problem themselves, in line with the general policy of cutting expense where possible. This report describes specific in-stances of successful unwatering by operators.

Jan 1, 1933

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By T. H. Davis

Twelve laboratories from the Western United States and Canada participated in radon progeny intercomparison measurements at the U.S. Bureau of Mines radon calibration facility in March 1987. The participants intercom pared grab-sampling and automated equipment methods at high and low concentrations of radon progeny and condensation nuclei (CN). The objective of this intercomparison was to determine if the measurement procedures and equipment of the North American facilities are equivalent. The sampling results showed good agreement among all participants. The standard deviation for the working level measurements was less than 3.5% for 1.70 working level (WL) and less than 8.8% for 0.21 WL. This relatively good agreement was achieved by using alpha standards calibrated by National Bureau of Standards (NBS) and by closely checking and monitoring airflows.

Jan 1, 1989

By John F. Wiggert

The first signal system used in the Homestake mine between the cagemen and hoisting engineers was a mechanical one. It consisted of small cables or jointed steel rods hung in the cage compartments and counterbalanced with weights or springs. These cables or rod strings were connected to the mechanically operated gongs at the engineers' positions by means of bell cranks and steel wires. At the various stations the bell lines were also fitted with bell cranks and connected levers, so that the cagemen could operate the bells from the stations when they were handling rock or other material and not riding on the cages. Such a system was inherited from the days before extensive electrical development. It served quite well for shallow shafts, but for depths of a thousand feet or more it was very slow and cumbersome. It required consider-able muscular effort to operate it quickly, because of the inertis of its great weight and also because of frictional resistance. The maintenance cost was quite high because of the many wearing parts.

Jan 1, 1937

By M. J. Ferrante

Relative enthalpies of high-purity disodium hexatitanate (Na2Ti6013) were measured at the Bureau of Mines to provide new thermodynamic data needed to advance the technology of materials. Measurements from 298.15 to 1,478 K were made by drop calorimetry with a copper block. Tabulated values are listed for the standard relative enthalpy, heat capacity, en-tropy, and Gibbs energy function between 298.15 and 1,500 K. Enthalpy data are also given in equation form and are combined with thermodynamic data from the literature to derive values of standard enthalpies of formation, Gibbs energies of formation, and logarithms of the equilibrium constants of formation. Similar calculations were made for the reaction of Na20 with Ti02.

Jan 1, 1986

By H. R. Batchelder

Much information on oxygen production and the manufacture of synthetic liquid fuels has been published during the past several years. From time to tine the investment and operating cost of oxygen plants of various sizes has been estimated. Surveys have been made so that the various processes by which oxygen is produced commercially might be compared. The gas-making processes in which oxygen is employed, which wore used in Germany during the war, have been described in T.O.M. reels, and this information has been published. Descriptions of pilot-scale or proposed commercial plants for the production of synthesis gas or hydrogen and their conversion to synthetic liquid fuels also have been published. In general, each of these publications has dealt with a particular phase of the over-all problem. The present paper will discuss the relationship between these phases: The factors that affect oxygen manufacture and costs, the methods for the use of oxygen and for the production of synthetic liquid fuels, and, to some extent, the economic factors that must be considered.

Jan 1, 1951

By Lloyd A. Morley

This report abstracts project work performed under USBM Grant GO155003 during the period 4 November 1975 to 3 November 1976. The research was funded, as a continuance of previous support from USBM Grants GO133077 and G0155003, to gain further knowledge in mine electrical system safety. Five reports have been separately produced, all under the grant title, "Coal Mine Electrical System Evaluation," and are as follows: 1. Volume I - Continuous Monitoring, 2. Volume II - Transient Analysis, 3. Volume III - Shielded Cables, 4. Volume IV - Computer Modeling, and 5. Volume V - Battery and Battery-charging Safety. Abstracts of these comprise the balance of this document with one exception. The task ?d-c offsett currents," does not fall under the scope of the other report volumes and, further, the material to be presented does not justify a separate report. Hence, this subject concludes the Executive Summary.

Jan 1, 1977

By E. L. Litchfield

Descriptions are given of the techniques and apparatus used by the Bureau of Mines for determinations of flat plate ignition quenching distance and minimum spark ignition energy. The descriptions include discussions of reaction vessel materials, shapes, and sizes and discussions of electrode configurations. Spherical, hemispherical, or flat plate electrodes are recommended. The preferred metal in electrodes and electrode supports is stainless steel; the flat plate electrodes incorporate flanges of low electrical conductivity which are most frequently formed from glass. Various aspects of the electrical energy supply system are discussed and suitable arrangements of components are indicated. The concept of a thermal relaxation time is introduced as a basis for the choice of a minimum interspark time during the testing of a gas mixture. The following indicate the varied conditions under which these tech were utilized: Mixture pressures between 10 mm Hg and 45 psig, initial temperatures between -78° and +198° C, and gaseous mixtures representing wide ranges of cL.. D reactivity and corrosiveness. Minimum ignition energies were determined which varied from about 10-7 joule to nearly 103 joule.

Jan 1, 1967

By Seth C. Schaefer

The Bureau of Mines investigated the standard Gibbs energies of forma-tion AGfo, for NiCr204 (nickel chromite) and CoCr204 (cobalt chromite). High temperature galvanic cells employing stabilized ZrOz (zirconia) as the solid electrolyte were used to measure the open-circuit potentials for the cell reactions ?

Jan 1, 1986

By J. P. Powell

Systematic waterflooding was first tried in Washington County, Okla., in 1937, when a 40-acre project was begun in secs. 24, 29, 32, and 33, T. 27 N., R. 13 E., jointly by the Keener Oil Co. and the Phillips Petroleum Co. The property later was sold to Lee Morrison. A second project was begun in 1941 in sec. 14, T. 6 N., R. 12 E., by the Oklahoma Oil Corp. Both projects were abandoned by the end of 1942. A third project was begun in 1945 and the fourth in 1948, but 1949 actually was the beginning of intensive waterflooding development in Washington County. The results of previous waterflooding projects are described in Bureau of Mines Reports of Investigations.2 3 4/ Oil production in the county followed a similar trend, dropping to a low of 990,000 barrels in 1945, then steadily increasing until 1956, when more than 4 mil-lion barrels of oil was produced. Most of the increase in oil production is directly attributable to water injection.

Jan 1, 1957

By V. A. Marple, K. L. Rubow, B. A. Olson

"A virtual impactor personal aerosol sampler (VIPAS) bas been developed for use in diesel-equipped mines to collect size-separated samples or diesel exhaust and mine dust particles in the respirable size range. This sampler consists or three stages: a 10-mm cyclone, a 0.8- µm cutpoint virtual impactor and two filter cassettes. The large non-respirable particles are removed in a 10-mm cyclone. The respirable particles from the cyclone pass through a 0.8- µm cutpoint virtual impactor with the particles larger than and smaller than 0.8 JI.ID (mine dust and diesel exhaust particles, respectively) collected on two 37-mm filter cassettes. The sampling How rate is 2 L/min so as to be compatible with the standard respirable dust sampler and personal sampling pumps. INTRODUCTIONThe mining industry has been increasing its use of diesel-powered equipment in underground mines, especially in coal mines. With this increased usage has come an increased concern regarding the health effects associated with inhaling diesel exhaust particles since they are in the respirable particulate size range. A Mine Safety and Health Administration (MSHA) advisory committee directed MSHA to develop a sampling protocol for diesel exhaust particles to assess worker exposure (MSHA, 1988). In addition, the National Institute for Occupational Safety and Health (NIOSH) has recommended that ""whole diesel exhaust be regarded as a potential occupational carcinogen as defined in the Cancer Policy of Occupational Safety and Health Administration"" (NIOSH, 1988).Past work, with cascade impactors in both the laboratory and in underground coal mine studies, has shown that the diesel exhaust particles are primarily in the less than 0.8 µm aerodynamic diameter size range whereas the coal dust particles are primarily greater than 0.8 µm (Marple et al., 1986; Cantrell, 1987; Rubow and Marple, 1988; Rubow et al., 1990a, b; Cantrell and Rubow, 1991). This work has been jointly performed by the University of Minnesota and Bureau of Mines researchers over the last 8 years. Typical particle size distributions for a diesel-equipped coal mine and an all electric coal mine are shown in Figure l. Note that the particles in the < 0.8-µ.m mode are the diesel exhaust particles (seen only in diesel-powered mines) and the particles in the > 0.8-µ.m mode are coal particles (seen in both the electric-powered and diesel-powered coal mines). Chemical mass balance analysis was also performed on these two size fractions to determine the degree of particle cross-contamination in the two modes. This analysis showed less than 10% cross-contamination, i.e., in coal mines Jess than 10% of the diesel exhaust particulate was collected in the coarse fraction and Jess than 10% of the mine dust was collected in the fine fraction (Cantrell, 1987; Rubow et al., 1990a)."

Dec 1, 1996

By Paul W. Johnson, Ralph C. Kirby, Frank A. Peters

A series of economic evaluations of processes for producing metallurgicalgrade alumina from low- grade aluminous materials is being conducted by the Bureau of Mines to determine the relative processing costs . The two processes considered in this evaluation are concerned with the recovery of alumina from clay through the formation of ammonium alum . In the first process , dehydrated clay is leached with ammonium bisulfate solution ; in the second process , clay is baked with ammonium sulfate and then leached with water containing a small quantity of sulfuric acid . After the alumina is dissolved by either of these methods , the iron is reduced to the ferrous state to avoid crystallization of ferric sulfate with the alum . The recovery of pure alum requires two crystallization steps . The alum crystals are then redissolved and precipitated with ammonia to produce alumina hydrate , which is calcined to a - alumina . These evaluations are based on published work , and the proposed plants are designed for a capacity of 1,000 tons of alumina per day . The estimated operating cost per ton of alumina for the bisulfate leaching process is $ 117.06 , and for the sulfate baking process , $ 109.26 . Using a Marshall and Stevens chemical equipment index basis of 240.0 , the estimated fixed capital costs , in the same order , are $ 158 million and $ 146 million . Under current economic conditions , these two processes are not competitive with the Bayer process for the production of alumina from bauxite . Since small improvements will not reduce costs sufficiently to approach competitive costs , future research work with these processes should be confined to areas likely to result in major cost reductions .

Jan 1, 1965

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1954 was made under a co-operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 101 samples of aviation gasoline. Data also are given for 30 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers I 1954 production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 19 manufacturers of aviation gasolines and of 15 producers of aviation jet fuels are represented.

Jan 1, 1955

By J. E. Schiller

The Bureau of Mines has investigated the surface charge of amphibole asbestos fibers and nonasbestiform cleavage fragments, as part of the Bureau&apos;s fundamental studies to provide new knowledge on the physical and chemical properties of the amphibole minerals. Microelectrophoresis was used to measure the electrophoretic mobilities, in water, of particles from six asbesti-from amphiboles and seven nonasbestiform amphiboles over the pH range of 5 through 9. The particles generally ranged in size from 2 to 5 µm wide by 10 to 30 µm long. The isoelectric point was determined for four of the minerals, and values were found to be between pH 3.5 and pH 5. The minerals studied had zeta potentials that generally ranged from -25 to -so mv in neutral solution. Attachment of colloidal positively charged AgI was also studied as a means of determining surface charge. Scanning electron microscopy of amphibole particles that had been in contact with aqueous AgI showed equal attachment of AgI to asbestos fibers and to cleavage fragments; the extent of AgI coating was the same for both. The electrophoretic mobilities of asbestos fibers were essentially the same as those of elongated cleavage fragments of the same aspect ratio (particle length divided by width). Blocky particles from both asbestiform and nonasbestiform specimens had lower mobilities.

Jan 1, 1980

By F. C. Houghten, R. R. Sayers, C. P. Yalaglou

"Introduction.Atmospheric conditions relative to high temperature and humidity are of great importance in mining, as well as in such allied fields as railroad and vehicular tunnels. An extended investigation into the effect of these factors on men has been in progress for some time, both in the field under actual working conditions, and at the Pittsburgh experiment station of the bureau in cooperation with the American Society of Heating and Ventilating Engineers and the U. S. Public Health Service.For several years one of the writers (Dr. Sayers) and L. Harrington, supervising mining engineer of the bureau, have been studying the effects of hot humid atmosphere in metal mines on the comfort and efficiency of the workers. Some of the reactions experienced in still and in moving saturated mine air at temperatures of 90 to 100°F., with men at rest are presented in a recent paper.****The present paper is based on experiments made under carefully controlled conditions to determine the relative feeling of warmth experienced by men in atmospheres of various degrees of temperature and humidity. The work was conducted by the research laboratory of the American society of Heating and Ventilating Engineers, at the Pittsburgh experiment station of the Bureau of Mines, in special physchrometric chambers built for this purpose. It was carried on under the direction of F. Paul Anderson, director of the laboratory, Dr. R. R. Sayers and A. C. Fieldner of the Bureau of Mines. The results given in this paper are for still air only. Investigations of the effects of moving air are being continued, and will be reported later."

Jan 1, 1924

By W. P. Diamond

The Bureau of Mines has been involved in the drilling of vertical, horizontal, and directional coalbed gas drainage boreholes for mine safety since 1964. In that time, boreholes have been drilled in most of the major coal regions of the United States under a wide variety of geologic conditions. Many of the geologic conditions that occur in the coal measures are detrimental to gas drainage; others may be beneficial. Analytical techniques to determine the gas content of coal samples and evaluate regional trends of gas distribution have been developed. Drilling techniques that maximize the acquisition of coalbed gas data and geologic information have been determined. Although some of the geologic factors influencing the placement and potential success of coalbed gas drainage boreholes have been reported in papers on individual projects, a complete, systematic compilation has not previously been available. The objective of this paper is to pro- vide information on specific geologic factors that should be considered prior to, during, and after the drilling of coalbed gas drainage bore-holes. Many of the commonsense considerations that have been learned through many years of Bureau of Mines experience, but have generally not been reported formally, are included for those who may be considering coalbed gas drainage drilling for the first time, or who have not had the opportunity to encounter a substantial number of geologic situations.

Jan 1, 1982

"In sum, significant benefits to mine worker health have resulted and should continue to result from the synergistic scientific, engineering, and medical research in respirable dust. As always, an important objective is the rapid dissemination of the results of this research to industry. Video tapes and the Technology News series published by the United States Bureau of Mines (USBM) have been a very effective means of technology transfer. Individual no-cost subscriptions to the Technological News series are available from the Bureau of Mines, Branch of Technology Transfer, 2401 E St., N.W. Washington, DC, 20241.Two respirable dust conferences have been jointly sponsored by the Center, USBM, NIOSH, and MSHA. The proceedings from these conferences are titled:1. Coal Mine Dust Conference held in Morgantown, West Virginia on October 8-10, 1984 and2. Respirable Dust in the Mineral Industries: Health Effects, Characterization and Control held in University Park, Pa. on October 14-16, 1986.Copies of the proceedings from the first conference are available from the National Technical Information Service (NTIS):National Technical Information Service5285 Port Royal RoadSpringfield, VA 22161NTIS # PB86-169380Telephone Number: (703)487-4650Copies of the second conference proceedings, ISBN: 0-936712-76-7 (publication #3010), are available from ACGIH by writing toWilliam D. KelleyExecutive Director, A.C.G.I.H.6500 Glenway Avenue, Building D-FCincinnati, Ohio 45211Telephone Number: (513)661-7881During the period 1984-1987 more than sixty-four (64) papers and publications have been produced by the Center researchers. These publications have appeared in scientific journals and have been presented at national and international symposiums and meetings. A list of these papers, organized by topical headings, has been included in this publication.The generic center maintains a reference center that serves as a clearinghouse for technical information for the generic area and supplies reports on generic center accomplishments."

Nov 1, 1988

By Frank D. Lamb

"INTRODUCTION The use of beryllium and its alloys has come into prominence in the last 15 years and increased considerably during the war. In contrast to other light metals, such as aluminum and magnesium, beryllium is relatively hard, has a high melting point (1,285° C.), and other properties that make it resemble steel in many respects. It has a specific gravity of 1.85, is only slightly heavier than magnesium (specific gravity 1.74), and is appreciably lighter than aluminum (specific gravity 2.7). Its lack of ductility prevents its use as a structural material, but this difficulty may be overcome in the future by the use of various alloy forms. The only important commercial alloy in which beryllium is used today is with copper. The addition of small percentages (1/2 to 2 percent) of beryllium to copper imparts properties to the alloy that make it desirable for use in springs carrying electrical current, particularly at high temperature. Many other uses of berylliam are known, and new uses are being found constantly that make the metal of increasing interest.Possibly the main factor preventing the use of more beryllium is the lack of a large source of beryllium ore. Many beryllium minerals are found as minor constituents of natural deposits, some of the more common ones being beryl (Be3Al2(Si03)6), chrysoheryl (Be A1204), helvite (3(Mn, Fe) Be Si04. MnS), and phenacite (Be2Si04). Of the known beryllium minerals, beryl is by far the most common and has been found distributed rather widely throughout the world. It usually occurs associated with granitic rocks and is commonly found as a constituent of granitic pegmatite."

Mar 1, 1947