Search Documents

By Laurel A. Powers

The Bureau of Mines process for recovering Ni and Co from low-grade domestic laterites uses a reduction roast followed by an ammonia, ammo-nium sulfate leach. This investigation examined the waste streams of the process for their potential environmental impact and focused on the laterite residue produced. The U.S. Environmental Protection Agency's extraction procedure (EP) toxicity tests and column leaching showed that leachable metal concentrations would be low enough so that the residue would not be considered a hazardous waste under present definitions. Under nonacid leaching conditions, about the same amount of metal was extracted from laterites as from their residues, and the leachates were similar to water samples from an undisturbed laterite deposit. Washing tests on the laterite residue showed that ammonia and ammonium sulfate concentrations were reduced according to equilibrium stage calculations, resulting in residues that would be acceptable for revegetation. With water washing only, the residue would not be considered a hazardous waste even though significant amounts of Ni and Co were absorbed from entrained leach solution onto the residue. Washing first with fresh leach solution and then with water prevented this absorption and thus improved the overall metal recovery.

Jan 1, 1983

By Frank E. Williams

Nuclear detonation data were accumulated, studied, and evaluated by the Bureau of Mines to visualize how nuclear explosives might be used in a shale?-oil industry, The evaluation shows that the Green River Formation at the semi-isolated locale of Piceance Creek Basin, in northwestern Colorado; is thick and widespread enough to warrant consideration of nuclear mining in lieu of conventional methods, Because cost data for nuclear explosions are limited; cost comparisons are made largely by assumptions. Also described are the history of the shale-oil industry, the geology and size of oil-shale resources; and conventional mining methods and processing technology.

Jan 1, 1969

By E. A. Loria

High-quality sheet of electrowon molybdenum was attained by a sequence of procedure on pressed and arc-melted crystalline powders. The procedures included high-temperature, high-vacuum sintering treatments and the use of metal deoxidizers instead of carbon to improve the mechanical properties of the molybdenum sheet. Rolled sheet 60 mils thick was evaluated by tensile and bend tests, hardness measurements, microstructures, and recrystallization treatments. After stress relieving, yield strength ranged from 85,000 to 110,500 psi (0.2- percent offset) and ultimate strength ranged from 87,200 to 117,250 psi with 4.5- to 25-percent elongation observed for arc-melted sheet, and 5.0- to 23- percent elongation observed for powder metallurgy sheet. In room temperature bend tests the sheet yielded plastically, indicating that the ductile-brittle transition point was below room temperature. The diamond pyramid hardness (DPH) of the molybdenum sheet changed from 214 to 293 DPH for the stress-relieved condition to 177 to 185 DPH for the fully recrystallized condition. The brittleness of recrystallized molybdenum, reported by other investigators as characteristic of sheet prepared from commercial-grade hydrogen-reduced powders, was not in evidence. Recrystallized tensile specimens pulled at room temperature had an average elongation of 31 percent.

Jan 1, 1966

By W. T. Wertman

A research program to aid development of better petroleum-recovery technology is in progress at the Appalachian Experiment Station, Bureau of Mines, Morgantown, W. Va. The work is part of the overall effort of the Federal Bureau of Mines to effect true conservation of the Nation's natural resources. Knowledge of the magnitude of the interstitial water content of oil-bearing formations is important to petroleum-reservoir engineers because of the influence of water on fluid flow during oil production and because of the significance of water volume in oil-reserve evaluation. Such information on Appalachian oil-bearing formations is needed to aid in planning secondary oil-recovery projects. Generally, the interstitial water content of oil sands can be estimated by one or more of the following methods: Analysis of cores obtained with oil-base drilling fluid, electric logging, restored-state or capillary-pressure tests, centrifuge tests, evaporation tests, or mercury-injection tests.

Jan 1, 1959

By Raghoottma S. Pandurangi, Mohindar S. Seehra

"The interaction of amorphous 1ilica particles with several hydrogen bonding agents (H2O, C2H5OH, C7H2NO) was investigated by monitoring the changes in the bulk and surface IR vibrational modes of silica using photoacoustic spectroscopy. It is argued that the intensity of the silanol band at 3747 cm-1 provides (an inverse) quantitative measure of the interaction or surface groups, along with the shift in the broad hydroxyl band, the interaction following the order C7H2NO > C2H5OH > H2O. Index Headings: Silica; Surface vibrational modes; Photoacoustic spectroscopy; Hydrogen bonding agents.INTRODUCTIONThe use of m spectroscopy to study the adsorption on solid surfaces is well documented in the literature.1 2 For example, hydroxylation of a clean silica surface results in the formation of the free silanol group Si-OH, with a sharp IR band near 3747 cm-1• Further hydroxylation produces a broad band near 3500 cm-1, which is believed to result from various hydrogen-bonded silanol bands leading to a multilayered surface structure of few nm.3-5 Earlier studies had indicated a relationship between the surface silanol band and various chemical activities of silica such as cytotoxicity, 7- 9 catalysis, 10-12 and others.13 Recent studies from our group14-in which the intensity of the silanol band and cytotoxicity of silica, heat-treated at various temperatures up to 1095°C, were investigated have provided a strong correlation between cytotoxicity and intensity of the silanol band.Coating of silica by PVPNO (polyvinyl-2-pyridine N-oxide with the empirical formula C7H8NO), a strong hydrogen bonding agent, is known to reduce the cytotoxicity of silica, presumably by chemically blocking the silanol groups from phospholipids.15 This interaction of the hydrogen bonding agents with the silica can be studied by m spectroscopy, and Knozinger16 and Rouxlet and Semples11 have used transmission m spectroscopy to study the effect of various chemicals on the surface IR modes of silica. However, one of the major disadvantages of transmission IR spectroscopy is that the sample preparation (grinding and mixing with KBr and pelletizing) usually distorts the surface modes (see, e.g., Ref. 14) and there is always a doubt about the effect of the sample preparation on the measured properties. In recent years, photoacoustic (PA) spectroscopy has become the technique of choice for studying the IR spectra of samples in their natural state, since no sample preparation is necessary.18•19 Moreover, according to a recent paper, 20 the relative intensity of the surface modes in PA spectroscopy of silica particles is much higher than that in transmission FT-IR spectroscopy. Consequently PA spectroscopy is ideal for studying the surface chemistry. In this work, we have used PA spectroscopy to investigate the interaction of three hydrogen bonding agents (C7H8NO, C2H50H, and H20) with the silica surface by monitoring changes in the surface m modes. Our results show that the surface IR modes get perturbed to a larger extent than the bulk IR modes in interaction with the hydrogen bonding agents. Moreover, whereas in the earlier studies, the shift of the broad silanol band near 3500 cm-1 was used as a measure of the interaction with hydrogen bonding agents,16•17 here we show that the relative decrease in the intensity of the sharp silanol band near 3747 cm-1 also serves as a quantitative parameter for the relative surface coverage and surface modification. Details of this work are given below."

Jan 1, 1990

By Young W. A.

The Eagle Silver mine is in the Rush Valley mining district, Tooele County, Utah, and is now operated by the Hampton Mining Co. The property, originally referred to as the Argent, is reported to have been one of the first discoveries in the district. The early operators mined ore to a depth of 850 feet, at which point the property was abandoned because of excessive water. During 1905 the Honerine tunnel was driven into the area approximately 1,800 feet below the collar of the Argent shaft. This tunnel served to drain the levels above and operations were resumed. Ore deposits in the Eagle Silver mine occur in the Galena King lime-stone, a 20-to 60-foot member of interbedded quartzite and limestone in the Oquirrh formation of Pennsylvanian age. This member has been faulted along the bedding, forming the Galena King gouge. Mineralization commonly occurs in or near this gouge area in a brecciated, highly altered, pipelike zone. The known ore shoots occur in association with the breccia pipe, commonly adjacent to cross faulting and porphyry intrusions. In general, two ore shoots have been mined on the upper levels of the mine, one lying to the east and the other to the west of the breccia zone. The Bureau of Mines diamond-drilling program was begun during the latter part of 1948 and completed early in 1949. Nine holes were drilled, aggregating 852.8 feet. Sludge and core samples from mineralized sections were analyzed in the Salt Lake City laboratories. A total of 87 sludge, 71 core, and 11 chip samples was submitted for analysis.

Jan 1, 1950

By J. A. Eisele

The Bureau of Mines is investigating the recovery of alumina from domestic nonbauxitic resources, including anorthosite. The United States has large reserves of anorthosite, but its aluminum content is less than 50 pct soluble in acid, unless a source of fluoride is added to the acid. A flowsheet that includes leaching with HCl and fluoride followed by crystallization of AlC13.6H20 from the pregnant liquor by HCl gas injection was designed. Approximately 90 pct of the aluminum values were recovered from the anorthosite when a ratio of 0.14 mole of fluorine per mole of aluminum was used. Sodium chloride is cocrystallized with the A1C13.6H20 but is removed by water washing of the Al203 product. A material balance is given based on results of laboratory studies of the unit operations.

Jan 1, 1983

By G. E. McElroy

This report discusses the construction and use of an all-pressure psy- chrometric chart in which the requirements of simplicity of appearance and absolute accuracy have been waived, to a certain extent, to provide for the rapid determination of psychrometric data and for the rapid solution of air- conditioning problems of major interest to the mining industry. Many mines in which air-conditioning problems are important are situated at elevations far above sea level and embrace great differences in elevation - in excess of 8,000 feet in certain mines → throughout their airflow circuits. Under these conditions, the effects of variations in the pressure of the at- mosphere upon the physical properties of the mixture of air and water vapor of which it is composed are considerable and should be taken into account in the solution of problems. The simple types of psychrometric charts in common use, such as the Carrier, Bulkeley, Hill, and Goff (American Society of Heat- ing and Ventilating Engineers Guide), are not generally suitable, in that they are drawn for a single barometric pressure 29,92 inches mercury.

Dec 1, 1947

By John C. Edwards

The Bureau of Mines developed a mathematical model to predict the oxygen requirements for a miner evacuating a mine. The model accounts for variations in the miner's escape speed with mine airway height, and for the empirically determined expressions for the weight-specific oxygen uptake rate for upright walking, stooped walking (duck-walking), and crawling. A Fortran computer program that is user oriented was prepared based upon the model's constitutive equations. Specific instructions for utilizing the program, as well as applications to miner evacuation from a mine, are presented.

Jan 1, 1986

By V. H. Gottschalk

Among the procedures developed by the Germans for providing the tonnage of iron powder needed to make rotating bands for artillery shells is the use of a ceramic tunnel kiln, not only for finishing the reduction of centrifugal powders but also for making so-called "brickyard sponge iron," which, after crushing and grinding, seems to yield a product suitable for powder-metallur- gical purposes. The final report issued jointly by the German Powder-Metallurgical Society (DPG) and the Chemical-Metallurgical Branch of the Research Depart- ment of the Metallgesellschaft, Inc. (ZFC of MG) gives the available details of this procedure, which may be regarded as a further development of the process in commercial use since 1911 at a ceramic plant in Hoeganaes, Sweden. The Bureau of Mines' wartime development of the Hoeganaes process also cul- minated in the adaptation of ceramic tunnel kilns for carrying out the solid- carbon reduction of iron ores, and comparison with the German technique should further advance the art. This information circular is issued as a supplement to Bureau of Mines reports of investigations Nos. 3819,2 3822, 3841,2 and 4271, on brick- yard sponge iron and is based on four German reports entitled "Making Iron. Powder in the Tunnel Kiln," translated from FIAT microfilm reel H-46, frames 9190-9209, 9280-9299, 9339-9357, and 9377-9384 (PB L 70042), which represent the four original research reports, Nos. 2005, 2008, 2010, and 2012, respec- tively, of the Metallgesellschaft, Inc.

Aug 1, 1948

By M. J. Ferrante

Enthalpy and entropy increments above 298.15° K were determined for cop-per sulfate between 298° and 1,000° K and for copper oxysulfate between 2980 and 1,146° K by the method of copper-block drop calorimetry. Enthalpies, entropies, and heat capacities are tabulated for both compounds. In addition, free-energy functions are tabulated for the sulfate. Equations representing the enthalpies are given for each compound.

Jan 1, 1972

By Robert H. Peters

This report presents findings from a Bureau of Mines study on barriers that may prevent miners from correcting and avoiding groundfall hazards. Such barriers stem from four basic types of problems: (1) inability to recognize groundfall hazards, (2) inability to correct groundfall hazards, (3) lack of motivation to search for groundfall hazards, and (4) lack of motivation to correct groundfall hazards. Data are presented that summarize the views of miners, section supervisors, and mine inspectors about the contribution of these barriers to groundfall accidents and what they think should be done to reduce the frequency of injuries sustained by falls of roof and rib. The report also includes a summary of miners' responses concerning their recent experiences with groundfall accidents, along with industrywide statistics on accidents and injuries caused by ground falls in underground coal mines.

Jan 1, 1987

By H. B. Salisbury

As a part of a research program designed to help minimize national requirements for new mineral commodities by maximizing recovery of metals from domestic secondary resources, the Bureau of Mines investigated the development of economic methods for recovering copper and associated metals from complex electronic scrap. Three types were selected for research: (1) multiple-pin plugs and connectors, (2) obsolete aircraft radio assemblies, and (3) the magnetic fraction of shredded electronic scrap furnished by the Bureau's Avondale Research Center. The plugs and connectors, after incineration to remove plastic components and melting, yielded a brittle ingot, as did the internal portion of the radio assemblies. The brittle ingots were ground to minus 35-mesh for processing, and the magnetic material was used in the as-received condition. A process using pretreated or raw scrap as a copper precipitant in various concentrations of acidulated copper sulfate solution was developed as a means of effecting an initial separation and upgrading in the form of high-grade cement copper containing all or most of the precious metals.

Jan 1, 1981

By D. A. Stanley

The Bureau of Mines is investigating a method of dewatering flocculated fine-particle waste that involves treating the waste with a high molecular-weight polymer such as polyethylene oxide (PED) followed by dewatering on a static screen and/or in a trommel. Dilution of the polymer solution used for dewatering and use of the ion-exchanged form of the montmorillonite clay were found to be major factors determining the amount of polymer required to dewater clay-containing slurries. The amount of polymer, A, required to dewater ion-exchanged montmorillonite can be described by the equation, An = kC + b where n, k, and b are empirical constants and C is the concentration of the polymer solution used for dewatering. Clays that require large amounts of polymer for dewatering also dewater to a lower solids content. The concentration of the polymer solution is important because it affects the radius of the polymer coil in solution and hence its ease of transfer to a bridging configuration by shear. The constant, n, a function of the charge to hydrated radius of the exchange ion, relates to the strength of the bond between the polymer and the surface of the clay through a water bridge. The constant k is related to the hydrated radi-us for sodium or to the unhydrated radius for the other exchange ions.

Jan 1, 1986

By R. G. Dressler

The Federal Bureau of Mines designed, constructed, and operated a demonstration plant at Louisiana, Mo., to produce gasoline, liquid fuels, and organic compounds from coal by a modified Fischer-Tropsch gas-synthesis process. Satisfactory equipment was developed to produce and purify synthesis gas and convert it into the desired products. Coal or coke was gasified with oxygen and steam to make a gas consisting essentially of carbon monoxide, hydrogen, and carbon dioxide. Dust in the raw gas was removed by cyclone separation, water scrubbing, and electrostatic precipitation. Carbon dioxide, hydrogen sulfide, and organic sulfur were removed with diethanolamine, iron oxide, and activated carbon. The gas was passed over iron catalyst and was converted into synthetic liquids, which were then separated and fractionated into gasoline, diesel oil, other liquid fuels, and oxygenated organic compounds. A 39-day continuous run demonstrated the feasibility of the process. Addition of 3 milliliters of tetraethylead per gallon of upgraded (or finished) gasoline gave a product with an octane rating up to 90 by the research method. After a caustic wash, the diesel oil was of a superior quality; its cetane number was 60 or above.

Jan 1, 1961

By F. B. Petermann

Two-stage electric smelting tests, using small submerged arc furnaces, were made on high-iron manganiferous materials from the Pioche District, Nev., and the Cuyuna Range, Minn. The object was to reduce sufficient iron in the first stage to give a slag with a favorable Mn to Fe ratio for smelting to ferromanganese in the second stage. The nodulized flotation concentrate from the Pioche District contained 29.2 percent Mn and had a Mn to Fe ratio of 2.3:l. When smelted with coke and silica or alumina as flux, more than 90 percent of the manganese was recovered in slags with Mn to Fe ratios of 10: :24:1. The Pioche slag was smelted to ferromanganese using coke and lime- stone or dolomite as flux. The ferromanganese was high in silicon but other- wise met specifications. Recovery of manganese to ferromanganese in this step was 73 to 78 percent. Overall recovery of manganese was about 70 percent. The sintered flotation concentrate from the Cuyuna Range material contained 12.9 percent Mn and had a Mn to Fe ratio of 0.3:1. When smelted with limestone as flux, about 83 percent of the manganese was recovered in a slag with a Mn to Fe ratio of about 6:1. The Cuyuna slag was smelted to ferromanganese with coke and limestone for flux. Recovery in this step was 61 percent of the manganese in a high silicon ferromanganese. Overall recovery of manganese was about 50 percent.

Jan 1, 1963

By J. D. Ramsdell

The purpose of this investigation was to determine the effects of the impurities, oxygen, nitrogen, carbon, and iron (in low percentages) on the mechanical properties of electrolytic titanium. The strength and hardness of binary Ti-O, Ti-N, and Ti-C alloys are linear functions of alloy content in the composition range investigated. Compared to oxygen and carbon, nitro-gen is the most effective strengthener and hardener, followed by oxygen, then carbon. When the carbon concentration is above 0.10 percent, carbides are present, and strength and hardness are relatively unchanged. For equivalent hardness levels, Ti-Fe alloys are stronger than binary titanium alloys containing oxygen, nitrogen, or carbon. However, the strengthening is related to the presence of transformed beta in the structure.

Jan 1, 1960

By William J. Campbell

One of the principal objectives of the Bureau of Mines program for developing super refractory materials is to obtain fundamental data on the physical properties of refractory oxides. This particular investigation obtained accurate thermal expansion coefficients for alpha alumina and evaluated, critically, those coefficients with other published values. High-temperature X-ray diffractometer measurements, by the Bureau, showed that alpha alumina expands anisotropically with expansion parallel to the c axis approximately 10 percent greater than parallel to the a axis. Thermal expansion characteristics of four different alumina samples were determined up to 1,200° C.; the results are presented in both tabular and graphical form. The combined random and systematic errors in the measurements are considered less than 3 percent above 500° C, and approximately 2 percent at 1,000° C. No differences in expansion were observed between the samples or between the heating or cooling cycles.

Jan 1, 1961

Reduce well construction and operation costs associated with in situ leach mining while increasing mineral recovery. Approach To accommodate the size of centrifugal pumps presently in use, in situ leaching production wells are typically drilled to 6 inches in diameter, while monitor wells are drilled to measure 4 inches in diameter. However, in order to reduce the cost of drilling these larger diameter wells and to increase recovery, the Bureau has developed jet pumps which have smaller diameters than centrifugal pumps of the same capacity. This allows both production and monitor wells to be drilled smaller. Bureau estimates indicate that the cost of drilling a 3-inch-diameter production well at in situ leaching operations would be about 35 percent less than the cost of a 6-inch well. Similarly, the cost of drilling a 2-inch-diameter monitor well would be about 26 percent less than the cost of a 4-inch well. Such significant savings in the cost of drilling these wells would effect a substantial reduction in total capital cost. Use of the new jet pumps can also increase the percentage of recovery because less costly wells allow closer well spacings, improving the distribution of the leach solution. How the System Works After the borehole is cased, the new small-diameter jet pump, along with piping and accessories, is installed and connected to a centrifugal pumping unit on the surface. High-pressure water from the surface pump is forced through a nozzle into the venturi of the jet type pump injector. This jet action lifts the leach and mineral-bearing solution to the surface.

Jan 1, 1984

By Martin Hertzberg

A comprehensive study of the flammability behavior of air-dispersed coal dust was made using an 8-liter Bureau of Mines system which included the following: (1) An optical probe to continuously monitor the dust concentration; (2) measurements of ignition energy requirements; (3) the use of several narrow size distributions ranging from 3 to 65 µm in average diameter; (4) measurements of the extent of flame propagation based on pressure attained at constant volume, residual O2 content after combustion, and flame and dust surface temperatures. The measured lean limit for near-horizontal propagation of Pittsburgh coal dust was about 135 mg/l (milligrams per liter), virtually independent of particle size. Required ignition energies were hundreds of joules and measured limit flame temperatures were 1,450 to 1,600° K. Data on inerting? requirements with KHC03, rock dust, and NaC1 gave approximately the same results as full-scale explosion tests. The good agreement suggests that the cause of earlier discrepancies between small-scale laboratory data and full-scale mine experiments may not have been the difference in size, but were rather a problem of proper care in isolating and controlling the significant experimental variables and in consistently defining the extent of flame propagation at the limits.

Jan 1, 1979