Search Documents

By B. J. Arnold, F. F. Aplan

"The captive bubble and sessile drop contact angle techniques have been used to evaluate the hydrophobicity of petrographically identified coal macerals. The magnitude of the contact angle on vitrinite is shown to be a function of coal rank ( %C, %0 and % vitrinite reflectance), increasing with increasing rank to a maximum for low volatile bituminous rank coals then decreasing for anthracite. The least data scatter is found when vitrinite reflectance is used as a rank parameter. Contact angles measured or estimated for other discrete macerals, indicate a variation in hydrophobicity based on coal type. These data correlate well with known flotation results. Coal is a heterogeneous mixture of plant remains and associated minerals that have undergone chemical and physical changes by biological and geological processes. These plant remains form coal macerals, discrete organic entities in the coal which have characteristic chemical and physical properties. As the differing chemical nature of each maceral will affect its behaviour in processes such as carbonization the separation of macerals during coal preparation may provide an important asset in coal utilization.Separation of some of the macerals based on specific gravity has been achieved in the laboratory, and by Sun and Cohen , in a study of two Pennsylvania bituminous coal preparation plants. It was indicated that the lighter exinites report almost exclusively to the clean coal while the denser inertinites are concentrated in the higher gravity fractions. The Longwy-Burstlein process6 took advantage of the difference in hardness or friability of the macerals by using impact breakage followed by screening to remove the more friable vitrain,clarain and fusain. The remaining durain, often high in spore content, was then recrushed. The re-mixed fractions produced the optimum size for obtaining the best coke strength for a particular coal.Separation or concentration of rnacerals by froth flotation largely depends on differences in the hydrophobicity of the macerals. Sun and Cohen 5 . indicated an order of decreasing floatability as exinite, vitrinite and inertinite, while a Russian study (as cited by Brown 7 ) showed that vitrains floated more readily than the duller types. More recently, Hirt and Aplan8 showed that 'pseudovitrinite' floats somewhat faster than does vitrinite while fusinite floats very slowly. Olson and A plan found that vitrinite floated easily while substantial quantities of the non-floated coal contained fusinitic material. Burdon noted that vitrinite is more floatable than semifusinite, and Sarker et a/. 11 have shown that vitrinite is selectively concentrated by froth flotation and oil agglomeration. Sun indicated that flotation, based on his calculated floatability index, should decrease in the order clarain, vitrain, fusain and durain; while Horsley and Smith 13 indicated the decrease to be: vitrain, clarain, durain and fusain. These differences can be attributed to the specific coals used in each study and to the individual macerals composing each coal type within a given coal."

Jan 1, 1989

By A. J. Kauffman

The alluvial deposits of the Pacific Northwest have been investigated and worked with varying degrees of intensity since about the middle of the 19th century. Earlier efforts, of course, were centered about the placer-gold content of the deposits; later, the Oregon beach sands were exploited for their chrome content, and, still more recently, deposits in Idaho were worked for their content of monazite, a rare-earth mineral which also contains significant quantities of thorium. The composition of alluvial deposits seems to depend mainly upon the nature of the source rock from which the detrital material was derived and upon the resistance of the individual mineral grains to the agencies of weathering and transportation. The processes of crushing and concentration used in ore dressing are applied in a leisurely but nonetheless effective manner when exposed rock masses are eroded by natural forces. Weathering effects a continuous disintegration and chemical decomposition, wherein resistant minerals are set free as individual grains and new minerals are formed. Erosion carries these detrital products down the slopes into natural waterways, where a mechanical separation of heavy particles from light is accomplished by the running water. The accumulation of such resistant, heavy particles through the ages has resulted in formation of the black-sand deposits. In addition to the associated gangue minerals, heavy sand deposits in the Pacific Northwest may contain the following constituents of possible economic value: Gold, platinum, chromite, ilmenite, magnetite, garnet, zircon, monazite, columbite-tantalite, and radioactive blacks.

Jan 1, 1956

By George W. Healy

The direct retorting of zinc sulfide concentrates in the presence of lime and carbon was examined on a laboratory scale with ten-gram charges of loose mix or fifteen-gram ones of pellets. A slow stream of nitrogen swept through the furnace tube over the boat of reactants, carrying with it the zinc vapor, which condensed on a rolled-up steel sheet near the exit, permitting weight of zinc produced to be obtained after completion of a run. Variables explored were percent of theoretical reagents, temperature, and time. During the runs gas samples were analysed periodically, and the content of CO2, CO and nitrogen were obtained. The quantities of the carbon gases could be calculated because the nitogen flow rate was measured. The gases were also examined for sulfur species, but neither COS nor SO2 could be detected at maximum sensitivity. Zinc recovery increased with excess carbon and lime and with temperature. It ranged from 77% at a ten percent deficiency to 90% at a ten percent excess at 1100°C. Going to 1200°C and theoretical reagents gave 93% recovery. Increasing time from 200 minutes to 300 minutes increased zinc yield by up to 10%. Results from sphalerite and a commercial concentrate from AMAX gave generally similar results. The reaction rate of zinc sulfide as sphalerite and of calcined sphalerite indicated that the latter reacted almost twice as fast, and recovery of zinc was five percent higher. Though the retorting step using sulfide, lime, and carbon proved to be non-polluting, it was feared that on storage the calcium sulfide in the residues would decompose, giving off noxious gases. Consequently the stabilization of the residues by oxidation was essayed. Because of the presence of unreacted zinc sulfide, the first product of oxidation was S02. Reaction of CaS to CaSO4 was incomplete, going from 20% at 800°C to 90% at 1200°C. Thus the non-polluting nature of the process as a whole is in doubt, and its economics are likely to be unfavorable compared to the traditional way of calcining the concentrates, followed by retorting of the oxide with carbon.

Jan 1, 1982

By G. W. Grove, O. V. SIMPSON

During the years 1945, 1946 , 1947 , and up to July 1, 1948, only one death was caused by mine fires in bituminous - coal mines of the United States . The one fatality occurred in an Illinois mine in December 1945, and , therefore, there had been a period of 2-1/2 years in which no deaths occurred as the result of mine fires . Moreover, 1946 was the first year since 1930 in which no deaths occurred from mine fires . This record is markedly better than that of 1944 , when 89 fatalities and great property damage were caused by mine fires in bituminous - coal mines and 16 additional men were killed by an explosion that occurred while they were attempting to seal a mine fire .

Apr 1, 1949

By Irving Hartmann, John Nagy, Donald Mitchell

"SUMMARY AND CONCLUSIONThe test data indicate that water infusion of the Pittsburgh coal seam does not reduce the amount of fine dust produced during mining operations to the extent reported elsewhere. Wide variations in the amounts of dust collected in the air current were noted in duplicate samples and repetitive tests. Changes in depth and location of the infusion holes and amount of water injected and addition of a wetting agent to the water had little effect on the amount of dust liberated.Water was forced readily into the coal. Some water flowed out along the cleats, but an appreciable amount remained in the seam. Little or no water pene¬trated the coal seam above the upper infusion holes.The average dust concentration (with and without infusion) in the return air, 40 feet outby the working face, was 25 million particles per cubic foot during undercutting, 20 million during drilling, 75 million during shot firing, and 20 million during hand loading. At the working face the average concentration was 3 to 6 times higher. The concentrations were measured at an airflow of 1,600 cubic feet per minute (c.f.m.) at the face.On the basis of this short investigation, no final conclusions can be made on the effectiveness of water infusion in reducing the amount of fine dust liberated during mining in the Pittsburgh coal seam. However, the data indicate that dust reduction resulting from infusion would be small.INTRODUCTIONThe production of fine coal dust is an inherent part of nearly every phase of mining. The use of large, high-speed continuous-mining machines and other mechanical equipment has increased dust production. In addition, in coal seams that have been subjected to high pressures for a long period, and particularly in dry and friable seams, some very fine dust is in the seam before mining. Much effort has been devoted to allaying and collecting at its source the fine coal dust released during mining. One of the comparatively recent techniques that has been developed for this purpose is infusion of water or other liquids into the coal seam. This method consists of injecting water under pressure into a coal seam to neutralize the fine dust released during mining. The water generally is introduced through bore holes in the face before undercutting."

Jul 1, 1957

By James A. Whelan

The Bureau of Mines sponsored research studies of variables in rotary drilling, done in the Department of Mineral Engineering, University of Minnesota. By studying carefully controlled drilling with good instrumentation, it was hoped to obtain a better understanding of rock failure during drilling and of the stresses in drill bits during drilling. Experimental procedures and equipment are described. From these studies it was concluded that 1. Thrust requirements, other things being equal, are proportional to the total length of cutting edge in the bit. 2. Data from penetrating a wedge into rock under thrust only are not directly applicable to rotary drilling. 3, In rotary drilling the initial wear on a bit greatly decreases penetration rate under any given set of conditions; however, after initial wear the effect of wear on penetration rate is reduced. 4. An increase in rotary speed increases the overall penetration rate but decreases the penetration per revolution. 5. An increase in thrust increases the overall penetration rate and the penetration per revolution. 6, Torque on a drill bit is proportional to both penetration rate and bit diameter. 7. For small-diameter holes full-hole drilling will save both drilling time and energy compared with pilot drilling followed by reaming; for large-diameter holes pilot drilling-reaming is advantageous in both respects,

Jan 1, 1962

By McHenry Mosier

This paper constitutes the third progress report on a national survey of the use of detachable bits in metal mines. It presents comparative costs of drilling with conventional and detachable bits and describes the operating practice in rock drilling and the reconditioning of drill steel and bits at 10 mines not discussed in previous reports.3/ ACKNOWLEDGMENTS This report has been prepared with the assistance and cooperation of the officials and staff members at the mines visited. Costs and other data at individual mines were developed and furnished by the operators.

Jan 1, 1937

By R. D. Brown

This Bureau of Mines report describes a new methodology for identifying and sorting scrap metals using two modern portable instruments: a thermoelectric sorter and a hand-held emission spectroscope. The method, tested on a 27-sample stainless steel and superalloy array, makes it possible to group and/or identify a typical mixture of high-value metal scrap in two or three steps, whereas as many as seven or eight steps are needed to perform the same separations using chemical spot tests. A portable fluorescent X-ray analyzer identified 19 of the 27 alloys in the sample array by name or type; these alloys are included in the microprocessor memory. The remaining alloys were identified by using the analyzer in its elemental analysis mode and comparing the results wit.h alloy specification chemistry.

Jan 1, 1984

By C. V. Jude

This U. S. Bureau of Mines (USBM) report presents results of stress analyses and field observations to investigate the effects of elevated trench drifts on the structural stability of rock mass zones surrounding a production draw drift in a mine utilizing a mechanized load-haul-dump (LHD) trench undercut panel caving system. A two-dimensional boundary-element mine stress model was developed to predict the locations and extent of damaged rock mass zones surrounding draw drifts where adjacent, parallel trench drifts are either elevated or not elevated above the LHD production draw drift level. A Mohr-Coulomb shear-failure criterion was obtained directly from in situ borehole shear test data. Hock-Brown shear-failure parameter values were computed from borehole-shear and triaxial test data. A procedure is described to estimate these parameters when a rock mass rating (RMR) value and triaxial data on intact samples exist, and no borehole shear test data exist Results indicate that trench drifts, elevated to the level equal to the height of the LHD production draw drift, would not minimize material damage nor significantly enhance the stability of rib and crown pillar zones surrounding production draw drifts in the mechanized LHD trench undercut caving panel investigated at this mine.

Jan 1, 2010

By H. F. Yancey

Although a general relationship exists between the two criteria used to measure sharpness of separation -error area and probable error -they sometimes give quite different appraisals of a particular washing operation. Error area takes into account how the entire raw coal was treated, whereas probable error reflects only how the material of intermediate density was separated, ignoring completely the recovery of clean coal and the rejection of heavy impurity. Error area is thus more reliable for general use. In heavy-medium cleaning, sharpness of separation decreases with increase in separating density, but ordinarily the change is not great enough to affect the yield and ash content of washed coal measurably. Therefore, distribution curves for heavy-medium units can be transposed from one separating density to another, at least in the range of separating densities ordinarily used in the United States.

Jan 1, 1955

By C. G. Maier

The present trend of chemicometallurgical research toward widespread and inclusive use of thermodynamic methods requires the inclusion of available data of this sort in any comprehensive metallurgical report . Such data for manganese are far from adequate for the full utilization of these methods . Even if our knowledge of these properties is weak , the collection of available figures is nevertheless well worth while , especially if their utilization in an approximate way may show inherent possibilities of application . No less important is the necessity for discovering the vital gaps in the existing information , to serve as a basis for further pertinent study . The utility of the thermodynamic methods of Lewis and Randall ( 234 ) 3 has become increasingly evident to metallurgists . It is true that at present no better approach to the general , fundamental problems of chemical metallurgy is available than close adherence to these methods . The effort is here made to collect and correlate , as far as possible , significant quantitative thermodynamic data on manganese and its metallurgically important compounds . There are considered here only the intrinsic properties of pure materials . The order maintained as far as possible will be as follows :

May 1, 1934

By M. L. Glenn

The Bureau of Mines is conducting research on substitutes for chromium-containing alloys in order to conserve imported critical and strategic materials. Part of this research concentrates on finding low-chromium substitutes for heat-resisting stainless steels for the temperature range 600° to 800° C. Ferritic alloys are emphasized that have oxidation resistance provided by chromium contents as low as 10 pct and stress rupture strength provided by the precipitation of the chi(X)-phase intermetallic compound, (Fe36Cr12 (Mo, Ti)10). Initially, research was concentrated on selecting an alloy composition having a minimum chromium content with strengthening provided by the X-phase. An Fe-(10-12 pct)Cr-6 pct Mo-(1.5-2.0 pct)Ti alloy was selected. After the alloy selection, the tensile, stress rupture, and oxidation properties were determined. Stress rupture properties were found to be similar to those of 304 stainless steel. However, the alloys possessed brittleness during both stress rupture and tensile testing, possibly as a result of too high a content of molybdenum and titanium. Higher than expected oxidation rates were found that may be caused by the high molybdenum content.

Jan 1, 1984

By S. M. Shelton, J. B. Zadea, M. M. Fine, T. L. Johnston

"INTRODUCTION The Mayfield manganese property is about 25 miles south of Van Horn, in Jeff Davis County, Tex. The ore deposit is developed by a large open-cut and a small stope.An 8-ton sample was received for testing; it was taker at random from material on the mine dumps and consisted of a mixture of manganese oxides, barite, and siliceous gangue minerals. The manganese occurred largely as hard, massive, crystalline psilomelane, with a small amount of pyrolusite. The gangue minerals consisted of intermixed iron-stained sand stone, quartzite, chalcedony, calcite, quartz, and barite. Chemical analysis showed 8.9 percent manganese, 3.3 percent iron, 38.4 percent silica, 6.6 percent calcium carbonate, 7.1 percent barium, 3.1 percent alumina, 0.09 percent phosphorus 0.01 tungstic oxide, and less than 0.05 percentAnalysis of selected clean pieces of manganese minerals, free of gangue, showed 48.1 percent manganese end 13.4 percent barium, of which only 0.2 percent was present as barium sulfate. This indicated a limit in concentration. Barium was also present in the gangue as a separate mineral, barite (BaSO4), which has approximately the same specific gravity as the manganese oxide."

Apr 1, 1942

By E. H. Crabtree

This paper, describing the milling practices at the White Bird concentrator, Picher, Okla., is one of a series on milling practices being published by the Bureau of Mines. The concentrator of the White Bird mine, Canam Metals Corporation, is located in almost the geographical center of the present Picher mining cam' in the Tri-State district, one-half mile east of the town of Picher, 1 mile south of the Kansas State line, and about 18 miles west of the Missouri State line.

Jan 1, 1930

By P. C. Good

The Bureau of Mines conducted a laboratory investigation of a sinter-leach method to recover aluminum and fluorine from waste carbon potlining residues from secondary cryolite recovery operations in aluminum reduction plants. After removal of carbon by burning, the residue was sintered at 900° to 1,100° C with silica and N2CO3, then crushed and leached with dilute NaOH solution, dilute Na2C03 solution, water, or water containing residual Na2O which remained in the sinter after reaction and decomposition of Na2CO3. Over 90 percent of the contained aluminum and up to 87 percent of the contained fluorine were extracted from this waste product in the form of a mixed alkaline solution. Treatment of the alkaline solution with CO2 yielded a white precipitate containing 89 percent of the original aluminum and 61 percent of the original fluorine as a mixture of synthetic cryolite and alumina, together with a variable excess of soda.

Jan 1, 1969

By D. W. Frommer

Mineral dressing research was conducted by the Federal Bureau of Mines under a cooperative agreement with the St. Joseph Lead Co., on three samples of iron ore from the Pea Ridge deposit in central Missouri. The objective was to provide information on how to upgrade these submarginal ores and produce marketable concentrates. Samples were prepared from drill-hole cores of similar composition and character to produce (1) a medium-grade mixed hematite and magnetite, (2) a high-grade mixed hematite and magnetite, and (3) a high-grade magnetite. In all three ores phosphorus and sulfur constituted objectionable impurities; excessive amounts of silica were also present in the medium-grade ore.

Jan 1, 1960

By Richard N. Appling

This compilation presents information obtained through investigation of manganese deposits and a reconnaissance of potential manganese-bearing areas of southwestern Oregon and Del Norte County, Calif., from October 1952 to September 1955. The report includes maps, assays, and preliminary examination data on 39 manganese deposits distributed throughout Curry, Coos, Douglas, Josephine, and Jackson Counties, Oreg., and 1 deposit in Del Norte County, Calif. On the basis of mineral content the deposits can be divided into three groups: 1 Manganese silicate deposits, manganese oxide deposits, and manganiferous iron de-posits. Generally the oxides occur along the coast in the Curry-Coos County area, the manganiferous iron deposits are in the Josephine-Douglas area, and the manganese silicates are found in both the Josephine-Douglas and Jackson County areas. The deposits are characteristically irregular in form and usually small. Most silicate and manganiferous iron deposits are in metasediments of Triassic (?) age; oxide deposits are in sediments varying in age from Jurassic to Eocene.

Jan 1, 1957

By S. C. Termes

To help develop the basis for new fine-particle separation methods, the Bureau of Mines has investigated the use of cross-linked starches containing four chelating groups--carboxylate, iminodiacetate, dietha-nolamine, and xanthate--as flocculants for selected metal oxide and hydroxide mineral fines. It was found that those starches capable of interacting with the mineral surface by a chemisorpti,on mechanism (as indicated by zeta potential measurements) produced the highest recover-ies and'grades of the metal oxide or hydroxide when flocculated from a binary mixture with quartz. The effects of pH, dispersing agent, stirring rate, stirring time, and starch dosage on selective flocculation were studied for binary mixtures of hematite and chromite with quartz. Floc strength becomes important in achieving maximum recoveries by mechanical postflocculation separations.

Jan 1, 1985

By Wm. O. Vanderburg

This paper describing the milling methods at the Hughesville concentrator of the St. Joseph Lead Co., Hughesville, Mont., is one of a series of similar papers being prepared by the U. S. Bureau of Mines on practices at the various mills in the United States. The writer expresses his thanks for the courtesies extended by the officials of the company while visiting the property and acknowledges the assistance and helpful suggestions given by R. H. Willcomb, general manager, and Carl Martin, mill superintendent, of the Hughesville Division f the St. Joseph Lead Co.; and E. D. Gardner, supervising engineer, U. S. Bureau f Mines, Southwest Experiment Station, Tucson, Ariz., in gathering and compiling the data herein presented.

Jan 1, 1931

By V. E. Edlund

Pyrometallurgical studies by the Bureau of Mines demonstrated the feasibllity of sintering and smelting a low-grade flotation concentrate made by pilot-plant processing 10-percent manganese ore from the Maggie Canyon deposit, Mohave County, Ariz. Under optimum conditions 85 percent of the manganese in a flotation concentrate that assayed 36 percent manganese was recovered as standard ferromanganese. A blend of this flotation concentrate with high-grade dithionate pilot plant precipitate was similarly processed with a recovery of 90 percent of the manganese. Thorough mixing and pelletizing of the charge before treatment on the sinter hearth was necessary to produce a well agglomerated product by single pass sintering. Although satisfactory sinter was produced from a variety of material combinations, best results were obtained on a charge that contained 80 percent flotation concentrate and 20 percent return sinter fines. This combination was mixed with 6 percent coke, based on weight of concentrate; and 12 percent moisture. Sintering such a charge yielded a well agglomerated product containing over 80 percent coarse material, The results of standard crushing tests showed that the product was physically comparable to iron ore sinters and manganese nodules.

Jan 1, 1962