Search Documents

By R. L. Lincoln

The effects of adding from 1 to 50 atomic percent (a/o) to vanadium were investigated by the Bureau of Mines. Properties studied included as-cast and annealed hardness, microstructure, fabricability at room temperature and elevated temperature, tensile strength, electrical resistivity, and oxidation resistance at 625° and 800° 2. Additions of small amounts of hafnium resulted in lessened as-cast hardness, decreased electrical resistivity, impaired roll- ability, increased oxidation resistance, and greater tensile strength. Larger amount of hafnium caused greater as-cast hardness, increased electrical resistivity, further impaired rollability, continued increase in oxidation resistance, and lessened tensile strength. INTRODUCTION The purpose of this study was to determine the effect of hafnium additions on the properties of vanadium and to learn if this binary alloy had any special or unusual properties. This investigation is a part of a larger research project in which new and expanded uses of vanadium are being sought. Domes tic vanadium is found frequently in combination with uranium, and because of the demand for uranium as a nuclear fuel, there now exists a surplus of vanadium-bearing minerals and vanadium pentoxide as a byproduct of uranium production. Primary principles of conservation demand that greater use be made of this readily available surplus; finding suitable metals to alloy with vanadium to enhance its properties is one way to increase its utilization. This report is the result of an investigation of the effects on the properties of vanadium when hafnium is added in amounts from 1 to 50 a/o.

Jan 1, 1962

By F. A. Penning

A number of highly instrumented free fall tests were performed on an arrestment system for a man cage in a vertical shaft. Tests were conducted in the U.S. Bureau of Mines free fall test tower at the Colorado School of Mines. A single tooth safety dog was used to stop on 4x6-in. Keruing (Phillipine mahogany) wet and dry wood guides. The safety dog had a penetration depth of 1 in., an adjustable width from 1-1/2 to 2-1/4 in., and a tooth angle of 80 deg. Twenty-seven free fall tests were performed covering a range in weights from 3-1/2 to 10-1/2 tons, hoisting velocities from 850 to 1350 feet per minute. Average g loads were measured from a low of 0.6 to a high of 3.4. The electronic instrumentation included piezoelectric and seismic mass accelerometers, strain gages on structural and mechanical elements, load cells in the guides, and distance measuring. Computer analysis was used to correlate with experimental measurements used to calculate stress. A statistical analysis gave no indication that the velocity or area affected the wood crushing stress. The instrumentation revealed a chatter occurring during the stop as shown by the accelerometers, strain gages, and load cells. Additional work is required to analyze this newly discovered phenomenon. The chatter imposes loads much higher than the average g load.

Jan 1, 1980

By Kenneth Eilerts

[Efficient and econonic production of ?etroleum requiros knowledge of the propertios of rescrvoir fluids a:$. their characterintics of flow throayh porous forclntions. The cllanga in propertie s and flow characteri s- tics of fluids when their corosition is altercd cs a rnsult of reservoir- pressure decliae is of 'mecial i~ortenct? ir, planning wall-spaAng pro.yama and production schedules. Rct~ntion of the ~eatent poscible quantity of dissolved gac in the rescrvoir liquid gnneml'y is recognized cs ess~ntisl to mxim ultimzte recoverj of oil fro3 the underground reecrvoir. Ilo:rever, pro6uction mothodn tending to mintain gis in solution in the oil and re- sulting in the optimm ocolo~ic recgvery of oil not only vary from field to fiold but also my have to be changed from time to time in a given field as it is being depleted of its recoveraklo oil. Const vestly there is need tc investigztc tY.e propertiec of resa:-voir f kids corresponding to successivc stages of reservoir depleJ&ion with the view of obtnining infomation oacential to efficient prcriuctian practices.]

Jan 1, 1939

By Jon G. Bredeson

A survey of electromagnetic noise reports was performed and a summary of the results are given. Industrial concerns were surveyed for techniques to minimize the effects of electromagnetic noise and are presented. The common types of communication links used in mines today are presented. A mathematical development was presented which determines the probability of bit errors versus distance for various types of communication links designed for in mine use. The probability of undetected errors for the protocols of the communication links is given together with burst error detection.

Jan 1, 1981

By Walter Kawa

Coals of various rank were reacted by the Bureau of Nines in plasma jets generated from argon and argon-hydrogen mixtures containing up to 33 volume-percent hydrogen. Average plasma temperatures ranged from about 3,400° to 12,000° C. Products were a solid residue and a gas containing hydrogen, methane, acetylene, diacetylene, and oxides of carbon. The highest yield of acetylene obtained with argon plasmas was 15 percent by weight of moisture- and ash-free coal. The data indicated that acetylene yields of 40 percent or higher can be obtained from the reaction of coal in argon-hydrogen plasmas, although results from these experiments could not be correlated with operating variables because of low recoveries plasma contained sufficient energy to heat the coal to temperatures as high 9,000 or 10,000° C, but complete devolatilization did not occur in any experiment.

Jan 1, 1966

By Benjamin C. Pollard

The location and production potential of a large block of strippable reserves in North Dakota were determined by using published data as a base and adding new drill hole data or other data contributed by companies that presently own or lease coal lands. Only beds exceeding 5 feet in thickness, under less than 120 feet of overburden, and in large blocks of 5 million tons or more were included in the estimates. All such reserves are in the Fort Union Formation of western North Dakota and are lignite in rank. Sixteen large blocks of reserves evaluated in this study are estimated to contain a total of 4.1 billion tons of strippable lignite.

Jan 1, 1972

Numerical models play a significant role in the design of safe underground mining excavations and support systems. Advances in the capabilities of numerical modeling software, together with ever increasing computational speeds, have made it possible to investigate the very nature of the large-scale rock mass and its response to mining excavations. The improved understanding of the rock response obtained from modeling enhances our designs, resulting in greater stability and safety of the mining excavations. To help advance the state of the art in this field, the National Institute for Occupational Safety and Health organized the International Workshop on Numerical Modeling for Underground Mine Excavation Design. The workshop was held in Asheville, NC, on June 28, 2009, in association with the 43rd U.S. Rock Mechanics Symposium. The proceedings include 10 papers from leading rock mechanics and numerical modeling experts in the United States, Canada, Australia, and Germany. The papers address a wide range of issues, including various numerical modeling approaches, rock mass modeling, and applications in coal and metal mines.

Jun 1, 2009

By Charles G. Patmon

This paper describing the methods of dredging and treatment of gold-bearing gravels at the Lancha Plana Gold Dredging Co.'s dredge is one of a series of similar papers being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The dredge is located near the Mokelumne River, 12 miles west of San Adreas, Calif.; it is accessible by an improved dirt road from Jackson, which is about 20 miles distant.

Jan 1, 1932

By L. B. Pankratz

Heat contents, measured above 298.15° K, and derived entropy increments are presented in tabular and equation form for the two crystalline forms of zinc sulfide (sphalerite and wurtzite) and for four solid solutions of iron and zinc sulfides having the compositions Zno.,,6Fe0.302S, Zno.750Fe0.250S, Zno.650Fe0.3505, and Zno.498Feo.502S.

Jan 1, 1965

By Robert H. Ridgway

This circular outlines salient facts regarding the sulphur industry of the United States and the world. It is founded chiefly upon published information available in the literature of the subject. The Bureau of Mines has in its files additional, more detailed data upon many of the topics presented very briefly here, and will endeavor to assist the mineral industries and the public by giving further information in response to individual inquiries. It will welcome comments, criticisms, and contributions of data that may assist in making later editions of this circular more accurate, or in developing more fully the bureau's mineral files pertaining to sulphur. Throughout this paper sulphur is used to designate crude sulphur or brimstone, not sulphur produced from pyrites or' smelter gases.

Jan 1, 1930

By M. J. Spendlove

A progress report is presented on a research program in which an attempt was made to develop a practical sulfide-volatilization process for recovering tin from low-grade Bolivian ores. Shaft-furnace designs and operating techniques were studied in a series of experiments in which the objective was to sulfidize cassiterite to stannous sulfide, remove the stannous sulfide by volatilization, reconvert the stannous sulfide to stannous oxide, and collect the resulting fume. A shaft furnace was developed and operated in a final test in which many of the previous difficulties were surmounted. Since the supporting funds were exhausted at this point, the project was discontinued; recommendations for further improvements in furnace design and operation were made on the basis of interpretation of experimental results obtained in shaft-furnace experiments and other related studies.

Jan 1, 1955

By John C. Machisak

INJURY DATA and experience at coal mines in the United States for 1957 are presented in this bulletin under the following general sections: (A) General injury experience: Tables 1-6: Current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity. (B) Selected injury experience: Tables 7-36: Current data on causes of injuries, distribution of injuries by part of body injured, days of disability, extent of hand and machine loading, experience by employ¬ment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines. (C) Injury experience, by States: Tables 37-41: Data on injuries, injury rates, employment, causes of injuries, and severity rates. (D) Major disasters: Table 42: Data on major disasters from 1948 to 1957. A major disaster is defined as a single accident in which, or as a result of which, five persons or more are killed instantly or die at any time thereafter. (E) Historical coal-mine-fatality experience: Tables 43-47: Data on fatalities and their causes at bituminous-coal, lignite, and anthracite mines from the earliest records through 1957.

Jan 1, 1960

By L. Kaufman

Fifteen boride composites were synthesized by hot pressing and evaluated by physical and incendivity testing as non-sparking tool materials. The incendivity tests, conducted at the U. S. Bureau of Mines, Albany Research Center, compared the boride compo-sites with standard cobalt-bonded tungsten carbide material used for coal cutter bits. Two titanium diboride composites and two zirconium diboride composites out-performed cobalt-bonded tungsten carbide in wear resistance and reduced tendency to cause ignitions. However, three of these candidates exhibited undesirable chipping. The remaining candidate, a TiB2-(Ni, Cu) composite, did not chip, nor did it cause ignitions at levels where cobalt-bonded tungsten carbide tools caused ignitions in the incendivity tests. Thus, this material appears to be a logical candidate for further development.

Jan 1, 1973

By G. S. Scott

The Bureau of Mines is engaged in research to assess the hazards associated with the handling, storage, and use of combustible gases, vapors, and. liquids encountered in mines and in industry. As a part of this general pro-gram, numerous limits of flammability and ignition temperatures are being investigated for a wide variety of combustible materials, and methods are being developed to minimize the explosion hazards of these combustibles. The Bureau receives numerous requests for information on the explosion hazards of specified combustible mixtures under various conditions of use. This information circular has been prepared to assist those who may have similar requests. Destined primarily for the layman with a limited technical knowledge of the subject, it considers rather briefly the numerous factors that enter into the general problem of gaseous explosions and their prevention.

Jan 1, 1951

By Charles F. Jackson

Waste filling has been employed for many years for supporting the walls of stopes and preventing failure and subsidence of the surrounding and overlying rock formations, and its effectiveness for this purpose has long been recognized. It is used for permanent support in ground where timbering (including square-setting) is inadequate for more than temporarily supporting the walls of the excavations. It should be rioted, however, that effective as a good, solid fill may be in resisting heavy side pressure and direct weight, its usefulness for supporting large areas of back and preventing breaking and movement of the overlying rocks is limited. Even the strongest and most uniform rocks will break if the unsupported span becomes too great; and since filling cannot be packed tightly against a horizontal back there is always a possibility of the back breaking and consequent subsidence if the maximum self-supporting span is exceeded. Planes of separation, such as bedding and fault planes, slips, and joints, are common in all rock masses; these may occur above the stoping area where their presence cannot be ascertained by observation. If too much reliance is placed upon filling for the support of a large horizontal area of back (as contrasted to support of vertical or steeply inclined walls) large masses of rock may break along a. plane of weakness, compress the fill, and leave an open space into which caving of the overlying rocks may continue until the space is filled. In this paper the term "waste filling" includes any filling material other than ore - waste mine rock, rock from surface quarries or opencuts, sand and gravel, mill sands, or slags from smelting operations.

Jan 1, 1935

Any communication system requires at least three elements in order to function: a transmitting device, a receiving device, and a transmission line or propagation medium. Even the device children use, tin cans connected with string, consists or these three elements. One speaks into one can (transmitter), which vibrates at the same frequencies as the voice. The string (transmission path) picks up the vibrations of the can and carries them along its entire length. The other can (receiver) detects the vibration and reproduces the original sounds to a lesser extent depending on distance, tightness of string, type of string, etc. All communication systems depend on these three elements: transmitter, transmission path, and receiver. Communication systems can be divided into three fundamental categories: wired phone systems, radio systems, and carrier current systems. Sections 2.2, 2.3, and 2.4, respectively, describe these systems and explain the basic principles of how each works. Hybrid systems are those systems that use various combinations of the three basic communication methods. Hybrid systems are described in section 2.5. There are some other methods of signaling (stench warning, bell signaling, etc.) that can be used in underground mines to transmit or convey information. These systems, although they cannot be considered true communication systems since they do not provide voice or even two-way communication, are briefly described in section 2.6. 2.2 Wired Phone Systems Wired phone systems are all those that depend on a wire connection between phones with the wire carrying the voice signals. Figure 2-1 is a diagram of two typical wired phone systems.The top panel shows a simple single pair party line system. In this system each phone is connected to a common pair of wires, and a person speaking into one phone will be heard at all the other phones on the line. The bottom panel shows a multipair private line phone system. In this type of system, each phone is connected by its own individual pair of wires to a central switch or telephone exchange. To establish a call between two phones in this system, the lines between the two phones must be connected (switched together) within the telephone exchange. In early exchanges, the connections were made manually by an operator. These exchanges are called Private Branch Exchanges (PBX's). Today, equipment within the exchange can automatically connect each phone to any other phone in the system. These exchanges are called Private Automatic Branch Exchanges (PABX's). There are many different types of automatic exchanges. Some utilize switches to physically make each connection according to the number dialed. Other, more advanced exchanges are completely solid state and may even be computer controlled. [ ]

Jan 1, 1984

By Wm. O. Vanderburg

This report on the mining and milling of tungsten ores is the second part of a general study of the domestic tungsten industry. The first part, comprising general information on tungsten, has been printed as Bureau of Mines Information Circular 6821. The purpose of these papers is to increase efficiency in the mining, preparation, and utilization of the tungsten resources of the United States. The tungsten industry forms so small a part of the vast mining and metallurgical operations of the illation that private metallurgists have not had enough inducement to give special attention to the recovery of tungsten minerals from the ores, and many of the small companies are financially unable to undertake research work. A study of the milling of tungsten ores reveals that further improvement is possible, especially in the treatment of slimes. Recent experimental work by the Bureau shows that the flotation process is applicable to certain tungsten ores. The future of the tungsten industry it the United States depends to a great extent on utilization of the low-grade deposits of the contact-metamorphic type.

Jan 1, 1935

By C. P. Bowie, George L. Gates

"INTRODUCTION Experience in drilling oil and gas wells has shown that the voidance of blow-outs, twist-offs, fishing jobs, loss of circulation, and heaving and caving of shale formations into the drill hole depends largely on how well the drilling-mud fluid serves its purpose. A possible method for the control of the drilling fluids may be seen from a study of the relation between the particle-size distribution and some of the important drilling-fluid properties, such as the ability to build quickly a relatively impervious mud sheath on the wall of the hole in the porous formations penetrated by the bit during drilling operations. In a wartime economy, which urgently requires conservation of steel, proper functioning of the drilling fluid is particularly important because, as Parks 4/ has stated, intelligent use of good drilling fluids makes possible drilling of wells for thousands of feet in open holes without the necessity of setting protective strings of casing to control the movement of salt water, gas, and troublesome formations into the borehole; consequently, especially in deep wells, of proper drilling fluids materially reduces the need for casing and lowers the cost of drilling and completing the wells."

May 1, 1942

By S. L. Weber, V. Castranova, D. E. Banks, J. K. H. Ma, Y. Rojanasakul, J. Y. C. Ma, M. Bhat

"The mechanism of bleomycin-induced pulmonary fibrosis is not ye: clear. Recent studies have shown that alveolar macrophages (AM) can be stimulated by bleomycin in vitro releasing inflammatory cytokines, suggesting that the interaction of bleomycin with AM is an important step in the drug-induced fibrotic process. Bleomycin is known to bind DNA and generate oxygen radicals through complexation with Fe2+ and oxygen. To provide,more insight into the cellular oxidative property of bleomycin, v.s have developed a fluoromicroscopic method using 2',7'-dichlorofluorescin diacetate (DCFHDA) as an oxidative fluorescence probe to study the deomycin-induced intracellular oxidation in rat AM and the inhibition of the oxida¬tion by taurine, a compound known to inhibit the bleomycin-induced fibrosis. Bleomycin at 5 to 20 ug/ml has a moderate stimulatory effect (1.87- to 2.66-fold) on the secretion of superoxide anion. A high concentration of bleomycin (20 ug/ml), however, inhibits cell response to zymosan-induced secretion of superoxide anion. At 4 ug/ml, bleomycin has no effect on cell membrane integrity or morphology but results in a significant increase in intracellular oxidation. This oxidative process is Fe2-,-dependent and is accompanied by an increase in intracellular calcium (35 nM). Both the intracellular oxidation and calcium rise induced by internalized bleomycin are inhibited by pretreatment of cells with varying concentrations of taurine (25, 125, and 187.5 uM). The inhibitory effect on intracellular oxidation .vas found to be 36, 57, and 60%, respectively. These results demonstrate a stimulation-inhibition relationship between bleomycin and taurine on re cellular oxidation at a subcytotoxic dose of bleomycin, suggesting that the oxidative effect of the intracellular bleomycin-Fe2 complex is important in the initiation of the fibrotic process. — Environ Health Perspect 102 (Suppl10):91-96 (1994) IntroductionThe pulmonary system is most susceptible to oxygen radical-induced diseases due to its constant exposure to the highest oxygen tension, and the potential encounters with oxidant gases such as ozone, nitrogen oxides, and toxic doses of dust particles. The lung is also a well-perfused organ and thereby vulnerable to the effect of circulating xenobiotics such as paraquat, and, bleomycin, which is known to cause pulmonary injuries (1). Alveolar macrophages (AM), which act as a means of defense by phagocytizing inhaled dust particles and microorganisms while increasing production of reactive oxidative species, have been shown to play an important role in mechanisms leading to oxidative lung injury and fibrosis (2-4)."

Dec 1, 1995

By A. B. Hooker, L. C. IlsLey

"The last previous Bureau of Mines publication relative to details of permissible electric mine lamps is Bulletin 332, which describes 16 lamps approved prior to May 1930. Some of the lamps have become obsolete through the development of improved models which, with several new types, make it desirable to supplement the Bureau's published data relative to permissible electric mine lamps.In the following descriptions, lamps approved since May 1930 and prior to July 1, 1935, are placed in the three following groups: (1) Electric cap lamps, (2) electric hand lamps, and (3) lamps for miscellaneous applications,ELECTRIC CAP LAMPS APPROVED UNDER SCHEDULE 6B1. Edison model J lamp, approval no. 24. - The features that distinguish this lamp from earlier models of Edison electric cap lamps are:(a) The battery consists of two F-2 cells of square cross section and about 1-1/4 inches higher than M-14 cells in the model H lamp, making the battery narrower and higher than any of the earlier models of Edison cap lamps.(b) The cells are insulated from each other and the Monel-metal casing by enclosure in vulcanized-rubber baglike enclosures. Both cell terminals are insulated from the cell jar.(c) The battery is equipped with rubber-tube Bunsen-valve-type gas vents.(d) The battery casing is secured by a new-type magnetic lock.(e.) The battery and cover terminal clips have been redesigned to give a wiping contact."

Jun 1, 1936