Search Documents

By R. S. Rosso

A program to investigate the effects of hardened washers on the uniformity of roof bolt tension and the resulting ground control in an underground mine was carried out. The complete roof bolt installation and roof bolt loads, mine convergence, and bed separation were monitored for a period of five months. The results show no evidence to support or refute the theory that mechanical roof bolts offer better support when they are installed with a high uniformity of tension. Also shown is the fact that if the bolts are installed with a maximum deviation from the mean torque of ±15% the addition of hardened washers significantly improved the uniformity of the installed tensions in the roof bolts.

Jan 1, 1977

By D. F. Hambley

This manual contains a step-by-step procedure for the design of ore passes for open pit mines. The manual is comprehensive and deals with all aspects including location, design, construction and operating considerations. In the construction section, all applicable raising and shaft sinking methods are considered and cost estimates and advance rates provided for each. The design process is divided into several sections - rock flow requirements, support design, dump point design and draw point design. Use of this manual provides open pit planning engineers with a means of designing and assessing the feasibility of ore passes for their operations.

Jan 1, 1983

By Peter G. Kovalchik, Rudy J. Matetic, Susan B. Bealko, Adam K. Smith

Overexposure to noise remains a widespread and serious health hazard in the U.S. service providing and goods producing industries. Excessive noise can lead to poor verbal communication and reduce the ability to recognize warning signals. These dangerous work conditions can also cause stress and fatigue. Occupational hearing loss is a permanent illness, with no recovery currently possible. Method: National Institute for Occupational Safety and Health (NIOSH) has recognized Noise Induced Hearing Loss (NIHL) as one of the ten leading work related diseases and injuries in the United States, and has emphasized its importance as one of the critical areas expressed in the National Occupational Research Agenda. Results: One of the most serious noise problems in the goods producing industries is the operation of continuous mining machines during underground coal mining. In order to minimize occupational hearing loss, noise hazards are “designed out” early in the design process. NIOSH is leading a national initiative called Prevention through Design (PTD) to promote this concept. This paper describes the quiet by design approach of a noise control that reduced noise exposures of continuous mining machine operators by 3dB(A) using the four functional areas of PTD, namely Practice, Policy, Research, and Education.

Objective: To help prevent squeezes, collapses, and other pillar failures through better pillar design, thereby enhancing safety for underground mine workers.

Jul 1, 1997

By Michael J. Friedel

As part of an investigation aimed at mitigating the hazards caused by abandoned mine openings, the Bureau of Mines conducted a series of electromagnetic surveys in the Galena, KS, area of the Tri-State mining district. The application of monostatic ground-penetrating radar (OPR) and inductive electromagnetic methods for detecting and delineating hazardous mine openings and attendant features was demonstrated to be feasible for shallow mine workings (i.e., less than 35 ft) occurring below flat-lying areas. Accurate determinations of depth to a mine roof appeared to be limited to roughly 20 ft using the GPR method. Features such as mine voids, fractures, and zones of subsidence were located beneath the Mainstreet (State Highway 26) site using the GPR system. Both the GPR and inductive electromagnetic techniques satisfactorily located mine openings and pillars at the Hell's Half Acre site. Geophysical interpretations were supported by exploratory drilling and mine maps.

Jan 1, 1990

By Robert J. Hundhausen

The Young America lead-silver-zinc mine in Stevens County, Wash., was investigated by the Bureau of Mines during parts of 1946, 1947, and 1948. Results of the investigation are described herein. The mine is 1/4 mile northeast of Bossburg, Wash., the nearest railway station. An excellent paved highway (No. 22) connects Bossburg with Colville, Wash., 23 miles to the south. The property was located in October 1885. It is credited with a production of 2,178 tons of shipping ore since 1901. The shipping ore averaged 7 percent lead, 7.7 percent zinc, and 16.1 ounces silver per ton. The property is under lease and option to Walter E. Morris and Perry Leighton of Colville, Wash. The deposit crops out on a steep limestone bluff overlooking the Columbia River. The country rock is a highly metamorphosed, brecciated, marbleized limestone (Northport formation).

Jan 1, 1949

By N. E. Hanna

Originally developed for use in coal mines where on-shift blasting with explosives was prohibited, compressed-air blasting has been used for the past 15 years as a substitute for fixed explosives. With the current commercially available compressed-air systems -Airdox and Armstrong -coal is dislodged by a high-pressure discharge of air from a pressurized shell placed in the coal borehole. In the original systems stationary compressors were mounted on the surface or in the underground ventilated areas. These proved so successful that a mobile compressor unit was developed for use at the working face. Because of the possibility that such a unit might operate in a gassy atmosphere, the Bureau of Mines has investigated the hazards associated with operation under conditions where firedamp could accumulate in explosive concentrations. ACKNOWLEDGMENTS Grateful acknowledgment is made of cooperation of C. E. Carter, H. R. Hiller, R. E. Kennedy, H. Kohn, H. D. Metzinger, J. Mahoney, J. Nickovich, G. So Scott and I. Spolan in the experimental work.

Jan 1, 1956

By S. K. Ash

In arriving at economic losses in coal mining due to accidents, a statistician is confronted with many difficulties on account of the lack of information relative to nonfatal accidents. For comparative purposes the ex¬ perience of those countries, States, or companies that keep complete records can be drawn upon and an extimate can be arrived at whereby one State can be compared with another, or one mine compared with another in the same district. Such a comparison for the United States has been compiled by the United States Bureau of Mines. It will be observed in Table 1 that the cost per ton for accidents in the State of Washington for the year 1927 is higher than for any other State, with the exception of Georgia and North Carolina, with a small combined tonnage of 130,089 tons. (The figures for coal production in Table 1 are taken from Bulletin 319, 1930, of the United States Bureau of Mines.) The reasons why the cost of accidents in Washington might be higher than the average are on account of physical conditions such as steep pitches, faults, igneous intrusions, highly explosive coal-dust, extremely friable coals, presence of gravel and water, very gassy coal beds, rugged topographic conditions, inherently bad roof and floor, thick beds, and heavy cover. The nature of the coal beds requires the use of preparation machinery. The mines are often deep, and topographic conditions are such that long and fast haul¬ age becomes necessary. All of these factors not only tend to cause high cost of production, which is manifested largely in a. lower than average daily pro¬ duction, per man, but..they.also affect to some degree a tendency toward a higher than average cost for accidents.

Nov 1, 1931

By A. Aly Selim

This report describes the feasibility of predicting percussive drilling rates by equations derived from statistical regression analysis. The least squares statistical method was used and the analysis was performed both by direct and by stepwise linear regression analysis. The predicted penetration rate is a function of the drill power and the physical properties of the rocks penetrated. The results show promise that the technique may be of value in providing a mathematical model by which percussive drill manufacturers and users can predict the performance of a given drill. Experimental work involved two mining type percussive drills. Penetration data for these drills were determined from nine rocks drilled in the laboratory. Drill work rates (power) were determined in a separate series of experiments. Rock physical properties were measured from diamond-drill core samples taken from the same blocks used for percussive drilling.

Jan 1, 1970

By J. F. McCoy

As mining develops into deeper and hotter regions, the safety and health of miners require that the workspace be cooled. Toward this end, this program has successfully developed a high performance, low maintenance spray cooler of 5000 cfm nominal capacity. Further, a series of four 25,000 cfm, nominal capacity, spray coolers has been built and mine tested with satisfactory results. The smaller coolers have been patented and become commercialized with 50 units currently in service. The concept has been developed independently overseas with an unknown number of units in operation.

Jan 1, 1984

By M. M. Fine

This Bureau of Mines report describes the theory, experimental procedures, and the results obtained to date in the development of the Bureau's process for magnetically roasting iron ores using scrap iron as a means of reduction. Since magnetic separation is an operational step common to magnetic taconite plants, the preliminary research studies emphasized only the novel magnetic roasting step. The studies included the use of automobile scrap, ferrous reductants such as borings and turnings, and prereduced pellets. Technical feasibility of the process was demonstrated both on a bench- and pilot-scale. Quality magnetic concentrates with recoveries of over 90 percent were obtained from a direct shipping ore containing 59.5 percent Fe and from fine grained semitaconites with about 30 percent Fe.

Jan 1, 1966

By J. M. Mutmansky, C. Lee

"This paper outlines some of the work associated with a research study into the relationship between the characteristics of coal mine dust and the incidence of coal workers' pneumoconiosis (CWP). The project involves study of the chemical, mineralogical, and morphological characteristics of the dust. Early stages of the study have dealt primarily with the size analysis and elemental composition of airborne dust in continuous miner sections. This paper outlines the procedures and findings of the elemental analysis portion of the study.Most of the previous elemental analyses of coal were made available in the quest for information on the combustibility of coal dust or on causal agents and prevalence of CWP. However, no extensive studies have been performed to date, primarily due to the limitations of the analytical methods. A review of the analytical methods for elemental characterization of coal and coal dust particles is presented. TI1e comparisons are made based on the sample mass required, the sample preparation required, the destructivity of the test, and the capability of providing an easy multi-element analysis. The reasons for selecting the proton-induced x-ray emission spectroscopy (PIXE) method are outlined.The PIXE method was applied to both the airborne coal mine dust and channel samples collected from seven continuous miner sections in six different mines. Channel samples of the coal, roof and floor were collected and analyzed. Airborne dust sampling was performed using multi-stage cascade impactors and permissible 2.0 I/min pumps. Sampler locations were fixed in the sections with respect to the continuous miner and roof bolter or with respect to the intake and return airways. Sampling times varied from 45 minutes to 6 hours, depending on the dust concentration.The statistical analysis of the resulting elemental data is presented. Of particular importance are the analyses of the variation of elemental composition with size and the variation in elemental composition over the working section. One interesting finding is outlined showing the multivariate statistical analysis of the trace elements and its implications in the identification of the dust sources. The paper concludes with an analysis of the ramifications of the elemental data to related medical studies."

Mar 1, 1989

By H. C. Fowler

The social economy, or public interest, and national defense require wise development and efficient use of the oil and gas resources of the United States. In this development and use, and in the prevention of economic and physical waste of oil and gas, the objectives of the petroleum and natural-gas industries, the Government (Federal, State, and local), and the public are the same. Differences of viewpoint generally have originated in the failure of one of the triad to have a clear or complete understanding of the motives behind the activities of the other component groups or full knowledge of what each is trying to accomplish. The Unites States Bureau of Mines through its petroleum and natural-gas division makes technologic and scientific investigations pertaining to recovery,3 preparation, refining, and use of oil and natural gas with the view of reducing waste, increasing safety and efficiency and aiding economic development.

Jan 1, 1933

By H. P. Hermance

Preliminary examinations of the Parker and Webb deposits were made by E. E. Maillott, Bureau of Mines engineer in July 1942. The chemical and spectrographic analyses included in this report wore made at the Eastern Experiment Station of the Bureau of Mines at College Park, Md., under the general supervision successively of S. M. Shelton and of Paul M. Tyler, formerly regional engineer, Eastern Region. Beneficiation tests were conducted under the supervision of Frank D. Lamb. The mineral exploration was under the general supervision of J. D. Bardill, formerly district engineer. Acknowledgment is gratefully made to the St. Joseph Lead Co., in particular to John S. Brown and P. J. Mechin for their assistance. Special acknowledgment is made to the American Metal Co., Ltd., ,Ind to T. C. Moore for furnishing core-drill and assay data; to the Universal Exploration Co. and P. B. Jennings; and to the Northern New York Mining Corp. and C. H. Sprague for their permission to publish the core-drill dta. Excellent cooperation was given by Dr. W; M. Agar and C, L. Rogers of the Geological Survey.

Jan 1, 1949

By S. M. Dar

The U.S. Bureau of Mines constructed a full-scale model of a 15-ft-wide coal mine entry to use in combination with finite-element analyses to investigate roof support systems and various types of roof bolts. The objective was to enhance understanding of the fundamental mechanics of the interaction between rock and supports and the relative integrity of bolted mine roof as a function of roof bolt type, length, spacing, and tension, and the basic characteristics of the roof strata. The laboratory test results, when correlated with computer simulations using fmite-element analysis and underground verification tests, should provide a basis for desigillng safer, more cost-effective roof control systems and help to establish guidelines for employing fully grouted resin and mechanically anchored bolting systems. The background for this research, the research approach, the methods and equipment employed, and the results are described in this report.

Jan 1, 1989

By Forrest T. Moyer, Nina L. Jones, Mary B. McNair, Virginia C. Berté

To keep the mineral and allied industries informed of trends in the causes of accidents, and to point out the need for corrective measures, the Bueau of Mines collects, analyzes, and periodically publishes health and safety statistics. This report includes data for 1963 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following headings:

Aug 1, 1965

By Wilder D. Foster

In the method used in the Health Branch of the Bureau of Mines for petro-graphic identification of the minerals in a rock, the sample is crushed, ground to a fine powder in a mortar, the powder is put on a slide, a drop of index oil and a cover slip are added, and the slide is ready for examination. The rock should be ground fine enough so that most of the particles consist of only one mineral, otherwise identification is difficult. Finally, the amounts of the minerals present in the sample are estimated to the nearest 5 or 10 percent. When quartz grains are mixed with some claylike minerals) of which by far the most common example is quartz and kaolinite in a shale, grinding in a mortar does not always separate the quartz from the kaolinite; instead, the quartz grains become coated with the kaolinite and are not visible, even after careful search. Talc acts Similarly, but muscovite and pyrophyllite do not. In evaluating the possible silicosis hazard of breathing dust from a shale, it is essential to be able to see and identify all of the quartz grains, as the other minerals present are relatively innocuous.

Jan 1, 1949

By Thomas G. Chapman

The four major steps in the production of marketable copper are mining, concentrating, smelting, and refining. In a few cases, however, leaching takes the place of concentrating, smelting, and refining, and in others ores are smelted without being concentrated. Copper ores have been milled since the early days of mining in the United States. Except in the Michigan district, most copper ores went direct to the smelter until the so-called porphyry mines were developed. At present, although considerable leaching and direct-smelting ores are produced, the bulk of the copper ore mined is concentrated. Improved methods of concentration have kept pace with the increased tonnages of ores milled.

Jan 1, 1936

By Beatrice Lukens, David Schlain, John D. Prater

"The electrolytic manganese process4/ developed by the Bureau of Mines involves the electrolysis of a solution of manganese sulfate and ammonium sulfate in a diaphragm-type cell. Metallic manganese is deposited on the cathodes, and sulfuric acid is produced at the anodes. The spent electrolyte contains, in addition to the sulfuric acid, approximately 40 percent of the manganese sulfate and most of the ammonium sulfate originally present in the feed solution. This spent solution is used to leach fresh ore that has previously been subjected to a reducing roast. The resulting leach liquor is purified and returned to the cell.Manganese of very high purity is produced by the electrolytic process. The properties of this metal are so different from those of the best grade of manganese that can be made by any other commercially feasible process that it is virtually a new material. Electrolytic manganese has been used in the preparation of new high-manganese alloys with valuable properties.3/ and further developments are to be expected. The electrolytic manganese process not only results in a product of superior qualities, but is applicable to large tonnages of domestic ores that are unsuitable for direct use in producing ferromanganese.The future industrial use of electrolytic manganese is of course, related to its cost. Decreases in the cost of production will lead to wider use of the metal; conversely, increases in the volume of production made possible by greater demand will bring further .decreases in cost."

May 1, 1946

By Chas. F. Jackson

This circular is an abstract of a manuscript-completed in August 1932, which cannot be published in its entirety due to lack of printing funds. It was originally planned to publish the manuscript as one of a series of bulletins dealing with the mining and milling of ores of the principal metals. Because of the common association of lead and zinc minerals in many ore deposits, and because a considerable proportion of the zinc produced in this country is obtained as a by-product of lead mining or vice versa, it seemed necessary to treat the mining and milling of lead and zinc ores in the same volume.

Jan 1, 1934