Search Documents

Electrical trailing cable used to power coal mining machinery is frequently damaged in usage because of tensile strain or crushing effect of mining machines running over the cable. One of the repair problems is finding the exact location of a short or open in this cable so it may be spliced or otherwise repaired. The U.S. Bureau of Mines and FMC corporation signed Contract No. H0 122011 in August, 1971, to develop instrumentation for finding faults in coal mine trailing cable. This report describes performance of several existing instruments as trailing cable fault locators and also construction details and performance records of several cable fault location instruments that FMC designed, built and tested as part of this project.

Jan 1, 1973

By J. C. Gerdeen

This project was a supporting effort with research contract H0230016 at White Pine Copper Company. Creep properties of White Pine rock were determined. These and properties for bolted joints were used in finite element analyses of sections of the White Pine Mine which included analysis of bed separations in the roof and sloping faults. In-situ experimental measurements were made of tension, compression, and bending of resin bolts by use of strain-gaged bolts. Evaluations of bolting effectiveness and comparisons of predicted and measured roof behavior are given.

Jan 1, 1976

By W. A. Stickney

The Bureau of Mines conducted beneficiation and smelting studies on siliceous offgrade manganese samples to indicate effective methods of manufacturing silicomanganese from materials that cannot be economically beneficiated to meet General Services Administration (GSA) specifications for stockpiling. Laboratory and pilot-plant flotation tests were conducted on 2 samples, 1 from the waste-tailings dump of the Domestic Manganese & Development Co , Butte, Mont., and the other from the Nettie mine in the Butte-Philipsburg area. Smelting tests were made on the combined concentrates from the pilot-plant flotation tests and on part of the tailings sample The flotation scheme found to be adequate in laboratory tests and later in the pilot-plant tests consisted of flotation by a fuel oil-tall oil emulsion in an acid circuit (pH )-1-.8 to 5.0). The oil-emulsion reagent flocculated the manganese minerals and selectively floated them from the siliceous gangue, In the pilot-plant flotation test on Butte-mill tailings 90.1 percent of the manganese was recovered in a concentrate that analyzed 32.6 percent Mn, 4.8 percent Fe and 28.1 percent Si02. In the test on Nettie mine ore 90.8 percent of the manganese was recovered in a concentrate that analyzed 36 6 percent Mn, 5.5 percent Fe, and 26-4 percent Si02.

Jan 1, 1956

By Sean Gallagher, William S. Marras, Alan S. Litsky, Deborah Burr

This paper describes a comparison of the fatigue failure responses of older versus younger lumbar spine cadaver motion segment specimens. These specimens were repeatedly subjected to loads simulating those experienced by the spine in lifting a 9 kg load in different torso flexion postures (0, 22.5, and 45 degrees of flexion). An older sample of 36 motion segments (average age 81 years + 8 SD) is compared with a younger sample of 18 motion segments (average age: 47 years + 9 SD) with respect to the number of cycles to failure and results of survival analyses evaluating the effects of flexion and bone mineral content with and without the younger data set. Compared to the older sample of spines, the younger sample exhibited many more cycles to fatigue failure in all the torso flexion conditions (10020 versus 8267 average cycles to failure in 0 degrees flexion, 7124 versus 3262 in 22.5 degrees flexion, and 3229 versus 263 cycles to failure in 45 degrees flexion). The increased cycles to failure in young specimens is likely due to the increased bone mineral content (BMC) in younger motion segments (30.7 g + 11.1 g per motion segment versus 27.8 + 9.4 g). Cox regression analyses modeling both flexion effects and BMC indicate that betas are similar when just older spines are modeled and when younger specimens are included in the analysis. Betas for survival analysis models with and without younger specimens generally show little change for flexion (2.716 versus 2.756 for 22.5 degrees [0 degrees referent], 3.926 versus 3.380 for 45 degrees [0 degrees referent]). Bone mineral content shows a similar protective effect in both models (Betas: -0.127 versus -0.087). Overall, comparison of the models indicate that risk ratios are similar for 22.5 degrees flexion, slightly increased for 45 degrees flexion and slightly more protective influence predicted for BMC in the combined sample versus the older sample alone.

By R. H. Fernald, C. D. Smith

When the United States Geological Survey began operations at the coal-testing plant erected at the Louisiana Purchase Exposition at St. Louis, Mo., in 1904, it had already outlined a comprehensive plan for the systematic study of coals, lignites, and other mineral fuels with reference to their suitability for particular purposes and the methods by which they could be utilized most efficiently. Recognizing the need of information on the relative economy of producer gas as compared with steam for power purposes and the lack of comparable tests of American coals in the gas producer, the Geological Survey undertook investigations of the merits of different coals as producer fuel for the purpose of promoting efficiency in the utilization of the nation's fuel supplies. These investigations were carried on at St. Louis, Mo., and, later, at Norfolk, Va., and Pittsburg, Pa. The aet of Congress approved May 16, 1910, transferred the fueltesting work being carried on by the Geological Survey to the Bureau of Mines. This bureau is conducting producer-gas tests at P~ttsburg, Pa., and is publishing and distributing reports relating to all the fuel tests made by the Survey. These investigations into the possibility of generating producer gas in a commercial way for power purposes from the various fuels of the country have been associated with steaming, briquetting, coking, and other tests, all of which supplemented an examination into the nature, extent, and distribution of the fuels. The tests have all been made with carefully selected representative samples and carload lots of materials procured specially for the purpose by experienced collectors.

Jan 1, 1911

By F. Fraas, J. E. Conley

"The problem of recovering potash from the mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H2O), occurring in large quantities in the salt beds of Texas and New Mexico, has been under investigation at the Nonmetallic Minerals Experiment Station of the U. S. Bureau of Mines continuously since 1928. Most of the results previously obtained have been published in technical journals and in a series of Bureau of Mines Reports of Investigations.The experiments described in the present report were performed to ascertain whether a continuous countercurrent extraction of calcined polyhalite by hot water would yield satisfactory recoveries and concentrations of sium sulphate in the top liquor. Previous investigation by Storch 4 had shown that the rate of solution of uncalcined polyhalite was too slow to be of value in an industrial process, and Storch and Clarke 5 had demonstrated that calcination of the polyhalite greatly, accelerated the rate of solution in hot water, allowing most of the potassium sulphate to be readily extracted."

Sep 1, 1933

By R. O. Neal, G. St. J. PERROIT

As natural gas is a waning resource in many places, increased interest has attached to the use of gas for the manufacture of carbon black. Because of a large number of requests for information on the subject, the Bureau of Mines has undertaken a detailed study of the carbon-black industry, covering the mechanical details of commercial methods, with the purpose of increasing the recovery of carbon black by such processes. A study has been undertaken of the economic factors governing the carbon-black industry, the uses and properties of carbon black, the dE)velopment of more Itccurate methods of testing carbon black, microscopic examination of different grades of black, physicochemical study of methods' of mQ.nufacture now in use, and research on new methods of manufacture. Part I of this paper covers the engineering and economic side of the industry; the other phases of the investigation which have been under the direction of G. St. J. Perrott, of the Pittsburgh station.of the United States Bureau of Mines, are discussed in Part II.

Jan 1, 1922

Quickly and cheaply consolidate underground slimes to facilitate their use as backfill and permit their easy handling for other reasons. Approach: The slurry containing slimes is pumped into active stopes and electrokinetically dewatered to provide consolidated back fill. How It Works: To densify slimes electro-kinetically two electrodes are placed in the material to be dewatered and densified. Typically, the electrodes are pieces of wire mesh fencing. One is placed on the bottom, and the other is suspended in the slurry near the surface. Figure 1 is a simplified section of a test. A d-c voltage of 100 to 400 volts is applied across the slurry. This causes the solid particles which are in suspension in the water (usually these are negatively charged) to migrate toward the anode; simultaneously, the water moves toward the cathode. Water immediately adjacent to the negatively charged solid particle surfaces contains an excess of dissolved positive ions. When these ions are attracted to the electrode and move towards it, they also exert

Jan 1, 1976

By W. J. Boone

Experimental determinations were made of vapor-liquid equilibria data for a helium-nitrogen-methane system. A mixture composition was chosen to approximate the crude helium to be produced Or conservation that will eventually be further refined to obtain pure helium. Although there are publications of studies of the vapor-liquid equilibria of helium-nitrogen, helium-methane, and nitrogen-methane binary systems, there is little indication of work done on the ternary system of helium-nitrogen-methane. The experimental data presented in this report supplement the information available for the binary systems. The equilibrium vapor-liquid data and equilibrium vaporization coefficients are presented in tabular form. Graphs are employed to show an extensive amount of the data.

Jan 1, 1963

By Doris M. Hyde

The 350,000-barrel-per-day Bahamas Oil Refining Co remained closed throughout 1986. Financially troubled Charter Oil Co., joint owner of the refinery with Chevron Oil Bahamas Ltd., agreed in principle to have Chevron assume full ownership in return for canceling debts owed Chevron. Finalization of the agreement was pending at yearend. Burmah Oil Ltd. took more than a $30 million loss on the sale of its interest in South Riding Point Grand Bahama Transshipment Terminal to South Riding Point Terminal Holding Ltd.

Jan 1, 1988

By F. E. Cash

"Explosions in bituminous coal mines are preventable. The combination of adequate ventilation, thorough rock-dusting, and water on the cutter bars of mining machines and of empty and loaded cars will certainly reduce the hazard to a minimum, if not remove it entirely. This is the attitude taken by the Woodward Iron Co. in lessening or removing the dust and gas explosion hazard from its Dolomite and Mulga mines.This report was made possible through the willingness of Frank H. Crockard, president of the Woodward Iron Co. to make records available and to authorize their publication for the benefit of the coal-mining industry.The compilation of these data and preparation of maps was facilitated by the cooperation of M. Heard, general superintendent of coal mines, J. B. Whatley, assistant general super-intendent of coal, and R. P. Whetmore, chief mining engineer.The Dolomite and Mulga mines are about 16 miles southwest of Birmingham, Jefferson County, Ala., on a company owned and operated railroad which connects ore mines, coal mines, coke ovens, and furnaces.In the Dolomite property there is a 30°, 860-foot, double-tracked slope for hoisting, three manway and air slopes and one air shaft, all in rock.At Mulga there is a 220-foot hoisting shaft, an air shaft and two manways, and material and air slopes, all in rock to the coal bed.The coal in both mines comes from the Pratt bed, which is the next coal above the Mary Lee bed in the Warrior Basin. The coal is horizontal or slightly undulating, with thickness varying from 36 to 72 inches and averaging 50 inches.The method of mining is essentially room-and-pillar with modifications for mechanized sections. The mines produced approximately 1,100,000 tons with 2,328,309 man-hours exposure n 1929 and 900,000 tons with 1,697,436 man-hours exposure in 1930.Through the work of the safety department the entire personnel in the coal mines, as well as in other departments, makes safety an essential part of efficient operation.Both mines are gassy; Dolomite produces about 334,000 cubic feet and Mulga about 919,000 cubic feet of methane every 24 hours.The ventilation maps, two of Dolomite mines (figs. 1 and 2) and one of Mulga (fig. 3) give as much of the details of ventilation as is practicable to put on maps of such scale. As will be seen from these maps there are two main ventilating fans in Dolomite mine and two in Mulga mine and the general direction of the air travel is indicated by long arrows to fan 1 and short arrows to fan 2 in each mine. Each fan has a gas or steam auxiliary drive and each mine has a complete fan and power unit ready for operation in emergency.In Dolomite, recently taken data show that fan 1 exhausts 82,000 cubic feet of air per minute at 3.2-inch water-gage pressure, with an analyzed methane content of 0.15 per cent, and fan 2 exhausts 115,500 cubic feet of air at 3.8-inch pressure and 0.10 per cent of methane. In addition, a Capell fan at No. 2 air shaft is a standby or emergency unit.In Mulga recently taken data show that fan 1 exhausts 83,000 cubic feet of air per minute at 3.0-inch pressure and 0.18 per cent of methane, and fan 3 exhaust 119,000 cubic feet of air per minute at 5.4 inch pressure and 0.35 per cent of methane. Fan 2 at No. 2 shaft is a standby or emergency unit for the Mulga mine.The ventilation is on a split system in both mines. All part split and total returns are measured, sampled, and analyzed weekly, requiring one man two days each week. During December, 1930, 77 samples were collected and analyzed in Mulga and 78 in Dolomite. Two weekly reports covering part of December, 1930, are given here so that they can be studied to show control of ventilation in the Dolomite and Mulga mines. In the event that a split sample shows more than 0.50 per cent of methane, immediate steps are taken to lower the explosive-gas content. The reports follow:"

Mar 1, 1932

By Kenneth C. Ko

An engineering investigation was carried out on the technical and economic feasibility of implementing flexible liner/backpacking support systems In an advancing tailgate longwall mine. The system for a model mine consists of a circular tube constructed of liner plates and flyash backpacking. Flyash is pneumatically stowed into the tailgate. Small amounts of cement may be mixed to improve the support capability of the fill In difficult local ground conditions. Water is added inside the nozzle immediately prior to spraying. Results of theoretical analyses and a field test show that the designed system is technically feasible, can be cost-competitive, provides more stable ground conditions, and can Increase productivity and coal recovery, when compared with existing retreat longwall systems. In certain mine layouts, the new system can reduce the direct mining costs by a significant amount. The system would be particularly applicable to deeper coal beds with bad ground conditions.

Jan 1, 1980

By M. C. Bleiweiss

Various light sources were evaluated for use in a fiber optic lighting system for mining machines. It was determined that a metal halide arc lamp was best because of its resistance to damage from shock and vibration and the high luminance of the arc. Measurements were made of the percent transmission of the ½ inch thick glass window and the fiber bundles, the total lumen output of the diffuser assembly with a known input and of the average surface luminance of the diffuser assembly. These data were then used to calculate the theoretical output of the system given an estimated input from the source. A prototype 55 watt, single-ended metal halide source was then developed. In order to provide greater efficacy and higher throughput through the fiber optic cables, a variation of the lamp with thallium iodide added to the fill was developed. The lamp was modified and a ballast was developed to allow it to hot restrike.

Jan 1, 1986

By Albert Ketler

[Early Bureau of Mines research had produced a fluorescent mine illumination system which was approved by MESA under Schedule 29A for use as portable equipment Intense industry preference for machine-mounted hardware required a MESA 2G approved system. The modifications required to upgrade the portable system arc herein described.]

Jan 1, 1976

By Samuel M. Bryant

The purpose of this study was to develop procedures to measure Bingham flow properties for mine tailings and to use these to predict the possible consequences of a hypothetical tailings flow failure at the Tenmile Tailings Pond at Climax, Colorado. The consequences of such a failure were found to be minimal, and the failure itself highly; unlikely. Values of Ty (Bingham yield shear strength) and np (plastic viscosity) were measured for 10 materials using results obtained from vaned coaxial viscometer tests and triaxial tests.

Jan 1, 1983

By Stephen E. Stewart

This document presents the explosion-proof enclosures used severity of certification tests solutions to linear transient thermal and stress analyses of in underground mines. The results were used to assess the for enclosure windows relative to possible loads occurring in the actual mine environment. Cast iron electric light enclosures with polycarbonate and glass windows were analyzed under steady state thermal conditions (light burning) and for thermal shocks corresponding to an internal explosion (ignition of volatile mine gas) or external quenching (mine water spray system). Thermal shocks to the enclosure, caused by ignited gases or water spray, were applied via a series of load steps in the transient analysis. The temperature dependence of material I properties and of the film heat transfer coefficients were included in the model. The work demonstrates that thermally induced stresses are strongly influenced by the way the window is mounted in the enclosure. It also shows that the MSHA Thermal Shock Test, if performed on an unsupported lens (or window), produces lower stresses than the lens (or window) may experience in the mine environment.

Jan 1, 1984

By M. A. Hammer

In this study by the Federal Bureau of Mines Pennsylvania anthracite from the Eastern Middle field was oxidized by concentrated nitric acid at steam-bath temperature for 24 to 1,000 hours. The quantitative data obtained include yields of nitric-acid soluble and insoluble products and the distribution of carbon and ash in each. The acid-insoluble residues were examined for solubility in aqueous sodium hydroxide. With a sodium hydroxide concentration of at least 1 normal, a portion of the residue could be extracted in the form of a true solution. With lower alkali concentrations, peptization occurred. Alkali solubility of the residue increased with length of oxidation. However, when expressed in percentages of original coal weight, the alkali solubility remained essentially constant after 192 hours of oxidation. This suggests that the alkali-soluble products are converted to acid-soluble products at the same rate as the original coal substance is converted to alkali-soluble material. Microscopic observations of the peptization of the acid-insoluble residues revealed a gross micellar physical structure. The action of nitric acid is apparently not restricted to the surface of a coal particle. The acid penetrates the particle through the pore structure, dissolving some of the ash and altering the bonds between the coal micelles. The bond alteration, as indicated by ultimate analyses, involves the physical and chemical adsorption of the components of nitric acid. Some of the altered bonds are not thermally stable; this instability is shown by the complete loss of peptizing ability when the acid-insoluble products are heated above 200° C. This loss is accompanied by the evolution of water, oxides of nitrogen, and hydrocyanic acid.

Jan 1, 1961

By Eric E. Unger

Results are presented of a census of the machines used in surface coal mines in the United States. The numbers of each machine type and model reported to be in use are tabulated for large and small mines in the Eastern, Central, and Western regions. Also tabulated are the average daily usage times of the major machine categories and the numbers of machines that have acoustical and other cabs. Projections of the total numbers of primary production machines are given. It is found that heavy tracked dozers and wheeled front end loaders constitute the most prevalent machine types, and that generally a very few models of machines made by one or two manufacturers constitute a major fraction of the population in each machine category. About 70 percent of all machines are reported to have some kind of cab, and about half of these are reported to be acoustical gabs; it is noted that acoustical cabs generally came into significant use since about the early 1970's. It is observed that the percentage-wise mixes of equipment types used in the various categories of mines differ significantly for only a few types of machines, notably for heavy dozers and loaders, and for haulers, highway trucks, and internal-combustion engine-powered shovels and draglines.

Jan 1, 1977

By Henry Kreisinger, WALTER T. RAY

This preliminary bulletin was written as the first of a series of several on the significance of drafts in steam-boiler practice, the succeeding bulletins to be along the same lines but of a more advanced character. The conclusions arrived at are tentative, and are the result of a study of one of the many problems growing out of a general plan of the United States Government to increase the efficiency with which the coals of the country are being used. Greater efficiency requires better boiler and furnace design. The experimental study of drafts on which the conclusions presented in this bulletin are based formed part of the fuel-testing investigations that were carried on by the technologic branch of the United States Geological Survey and have been transferred to the Bureau of Mines. The experiments made seem to indicate that it is possible to double or treble the capacity of a plant without making any radical changes the furnaces and boilers. These increases require about double and treble the quantities of air to be put through the fuel beds and boilers. It also seems probable that rebafHing the boilers will often permit the capacity to be doubled or trebled, while still getting more steam than formerly per pound of coal for uses outside the boiler room. These experiments were undertaken with the object of clarifying ideas concerning the passage of air through fuel beds and boilers. Measured weights of air were passed through two beds of lead shot, series, one of which remained always the same and represented a boiler; the other being varied as to size of shot and depth of bed, and representing a fuel bed. Careful observations were made of the weight of air passing through the beds per minute. All data were plotted in many charts, so as to permit the study of them from several points of view. A number of laws were deduced bearing on the relative amounts of power required to force air through fuel beds of various thicknesses, composed of various sizes of coal, and through boilers of various lengths and areas of gas passages. An important part of the discussion relates to an increase in the capacity of boilers by increasing the amount of power applied to pressure and exhausting fans and thus forcing several times as much air through the fuel beds and boilers. may be possible, as a result of these investigations, to raise the rate of working the boiler heating surface to three or even four times its present value. Such an increase would undoubtedly mean new designs of grates, stokers, furnaces, and boilers, especially fitted for high rates of working. Fan equipments designed to supply three or four times as much air under several times the pressure would be provided with more efficient engines, thus giving an additional factor favoring high-capacity working. It must be borne in mind, as stated above, that the results are tentative. It will cost money to force gases at high speeds through fuel beds and boilers, and there will soon be pressing need of such quantitative data as will enable the largest possible part of the energy imparted by the fans to be advantageously utilized. We desire, to thank our superiors, especially Messrs. L. P. Breckenridge and D. T. Randall, for their helpful criticism and suggestions.

Jan 1, 1911

By M. Mahan, D. D. Blue, O. C. Garst, F. Fraas, L. Fink

"Early in World War II it became apparent that the known bauxite re- serves might not be adequate to supply the demands of the American aluminum-producing industry, as the transportation of bauxite from abroad to this country might easily be interfered with by hostile action. Consequently, the Bureau of Mines set up an intensive, well-integrated program for the production of cell-grade alumina from low-grade domestic ores. This pro-gram of investigation covered the production of alumina from clay, alumite, red mud, and other low- and marginal-grade ores. In line with the Bureau's usual policy of conservation of natural resources, it was decided that the investigation should be extended to cover the production of alumina and other valuable byproducts from aluminum dross.Statistical information showed that during the year 1943-44, an average of 2,900 tons of aluminum dross was generated monthly. This dross, after partial removal of free metal, had an average metallic aluminum content of approximately 9 percent. Some of this dross was produced by the melting of alloyed aluminum; but a large proportion 1,700 out of 2,900 tons - was generated by two producers of primary aluminum, and the dross did not contain an great proportion of alloying metals. Compared with dross from other sources, this 60 percent of the country's capacity can be assumed to have relatively uniform composition. Moreovcr, the problem of collection and distribution can be minimized because of the relatively small number of plants included in the organization of these two producers of virgin metal.Except for large pieces of metallic aluminum that easily can be mechanically separated for remelting, this dross has been discarded and scrapped. Inasmuch as chemical analyses show that the alumina content of dross is far higher-than ordinary ores - 111 percent alumina equivalent in dross compared to 57 percent alumina in bauxite - aluminum dross is a far richer source of aluminum than any known naturally occurring ores. The discard, of this waste material during the war and reconversion periods would be unsound economically. The work reported herein describes tests at the College Park Station of the Bureau of Mines on the recovery of metal, alumina, ammonia, methane, and abrasive-grade corundum from dross."

May 1, 1946