Search Documents

By L. J. Kane

Conventional methods for determining the size of dust suspended in a gas require that agglomerates (clusters of particles) first be broken into particles, but in evaluating industrial dust-removing equipment the size of the agglomerates as they actually exist in the gas stream is far more important. This paper presents results of an investigation by the Federal Bureau of Mines to develop methods for determining the size of dust agglomerates suspended in a gas stream. The studies are part of the Bureau's continuing research on synthetic liquid fuels. The size and size-distribution of agglomerates as they exist when the gas reaches the filter was determined by using a membrane filter in conjunction with a dust count under a microscope. A membrane filter is a cellulosic sheet about 150 microns thick containing millions of holes per square centimeter--holes of uniform diameter that run directly through the sheet without interconnection.

Jan 1, 1960

By Thomas J. Peters

In 1979 and 1980, the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the 15,600 acre (6,310 ha) Freel Peak RARE II area (No. 5271) in the Lake Tahoe Management Unit. This study by the Bureau of Mines indicates that potential for economic mineral resources in the area is slight. The only mineralized structures in the area consists of two quartz veins. One quartz vein, at the Mountain Top Mine (fig. 1), located by Fred Denner in 1932, is estimated to contain 2,000 tons (1,800 t) of silver and copper-bearing resources. Chip samples from the vein averaged 0.61 oz silver per ton (20.91 g/t), and 1.59 percent copper. The narrow vein is not economically mineable. The other quartz vein is poorly exposed and contains traces of molybdenum. A second reported molybdenum occurrence could not be substantiated.

Jan 1, 1982

By E. G. Davis

This report summarizes an investigation to determine the occurrence and recoverability of heavy minerals in sand and gravel operations in the Southeastern United States. A total of 61 samples from 34 sand and gravel operations in Alabama, Georgia, South Carolina, and North Carolina were studied. Heavy minerals, in amounts ranging from 3 to 400 pounds per ton, were found in all of the samples. Eighty percent of the samples contained 20 to 40 pounds per ton of heavy min¬eral. Valuable heavy minerals, in order of decreasing amounts, were ilmenite, kyanite, zircon, rutile, and monazite. Large-scale concentration tests were made on five samples from four major producers. Gravity concentration by Humphreys spirals and tables resulted in bulk heavy mineral concentrates that graded from 82 to 98 percent total heavy minerals. Mineral recoveries ranged, in percent, as follows: Ilmenite 60 to 95; zircon 96 to 100; kyanite 37 to 77; rutile 89 to 100; and monazite 96 to 100. Separation studies on the gravity concentrates showed they would respond to high-tension and high-intensity magnetic separation techniques to produce individual mineral concentrates. The recovery of each individual mineral from fractionation of the heavy mineral gravity concentrates, in percent, was: Ilmenite 77 to 94; rutile 41 to 68; kyanite 62 to 79; zircon 49 to 83; and rare-earth products, monazite and xenotime, 42 to 96. The grade of each mineral concentrate was: Ilmenite 51.1 to 68.7 percent Ti02; rutile 93.7 to 94.3 percent Ti02; kyanite 55 percent A1203; zircon 58 to 61 percent Zr02; and rare-earth products containing 73.8 to 90.8 percent monazite and 4.8 to 12.7 percent xenotime.

Jan 1, 1971

By Danny Riley, Brian Curry, Sandya Govindaraju, James Bain

Acute vibration causes vasoconstriction in naïve human subjects1. Vibration-induced decrease in skin perfusion has also been reported in the rat-tail vibration model 2. After vibration exposure, rat-tail arteries demonstrate vacuoles in smooth muscle cells, similar to that caused by pharmacological vasoconstrictors3. This study addressed the effects of different frequencies, durations and patterns of vibration on lumen size and vacuole formation using the rat-tail vibration model in male Sprague-Dawley rats (~300 g). Methods The different groups were: 4-hr continuous vibration at 30, 60, 120 and 800 Hz; continuous exposure durations of 5 min, 1 hr and 4 hr at 60 Hz; and 4-hr cumulative exposure of 60 Hz delivered intermittently in cycles of 10 min on and 5 min off. Acceleration was set at 49 m/s2 r.m.s. for all frequencies. Unanesthetized rats were restrained in cages on a nonvibrating platform with their tails placed on a vibrating stage driven by a B&K motor (4809). The sham control animals were also placed in the vibration apparatus but not vibrated. Room temperature was controlled at 25 ± 1°C. Ventral arteries from proximal tail segments 7 were immersion fixed in aldehydes, embedded in epon-araldite and sectioned (0.5 µm) for morphological analysis. Vascular lumen sizes were measured as the percent ratio of the lumen perimeter to internal elastic membrane length using Image J software (NIH). The number of vacuoles in the smooth muscle layer of each artery section was counted. Results Fig 1: Semithin sections of arteries. A. Sham control. B. 4-hr vibration 60 Hz. In vibrated arteries, the lumen decreases in size, and smooth muscle cells (SMC) exhibit vacuoles (arrow). Bar equals 40 µm for each panel. [ ]

Jan 6, 2006

By Frank D. McGuirk

Underground coal mining is traditionally hazardous. Although many danger-prone human activities are now performed by mechanized equipment, this mechanization has itself brought new dangers to the underground mining industry, and the loss of life and limb has caused increased concern for mine safety. The 1969 Federal Coal Mine Health and Safety Act has precipitated a great deal of safety-related research on the part of the Government, industry, and private agencies. Much of this safety research has been focused on the new and varied man-machine interfaces caused by increased mechanization. Recent projects in this area have dealt with standardized controls, emergency shutdown capabilities (panic bars, strike plates, self-centering controls, "dead man" controls), and machine operator protective devices (fully enclosed cabs, canopies, side rails). There was a need for integration of the findings of current and past projects to move rapidly toward the smooth, orderly implementation of standardized operator work station designs for underground mining equipment.

Jan 1, 1975

By Annie G. Smelley

The Bureau of Mines is testing a dewatering technique for phosphatic clay waste that will recover a portion of the water lost using conventional waste disposal methods and produce solids suitable for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong, stable flocs that can be dewatered on a static screen followed by further dewatering on a rotary screen. In field tests conducted in northern Florida, clay wastes containing a nominal 2.5 pct solids have been consolidated to greater than 20 pct solids. The rate at which PEO-treated material continues to dewater in a mine cut also was monitored. Preliminary results indicate that PEO--treated material will dewater to 30 pct solids in 140 days. Pretreatment of phosphatic clay waste with lime and H202 was shown to improve the dewatering technique for problem clay wastes.

Jan 1, 1985

By R. H. Grau, R. B. Krog

The National Institute for Occupational Safety and Health (NIOSH) has investigated the unique ventilation requirements of large-opening mines to help identify and evaluate the effectiveness of various fan types to improve the ventilation and air quality in the underground workplace. Large-opening mines, with their low airflow resistance factors, can be ventilated with free-standing auxiliary fans because airflow pat-terns in these mines are primarily controlled by airflow momentum. The flow characteristics of both vane-axial and propeller fans were investigated and tested at four large-opening mines to assess the effects of fan location on recirculation and entrainment. Each fan type has its own airflow, entrainment and penetrating air-flow characteristics, and operating costs that are advantageous for specific applications. Either fan type can be used for most auxiliary applications. However, this research has shown that the optimum placement and use criteria for propeller fans differ from those promulgated by the U.S. Bureau of Mines (USBM) for vane-axial fans Brechtel et al. (1985)

By George A. Burrell, G. W. Jones, Frank M. Seibert

In this bulletin, the style of Bulletin 42 has been closely followed. Much of the material is reprinted on the following pages in its original form, and changes have been made only where manifestly neces- St,ry. Laboratory methods have been brought up to date. Some types of apparatus described in Bulletin 42 have now become obsolete and newer designs are described instead. The authors hope that this bulletin will be of as much service as was Bulletin 42.

Jan 1, 1926

By Richard L. Ash

Introduction The blasting capabilities of commercial explosives are often rated according to their loading densities and detonation velocities. Both the density and velocity are relatively easily measured, the values of which can be used for determining the approximate detonation pressure developed by an explosive during any given set of blasting conditions (1-5). Knowledge of the actual rate of detonation attained at all points along a charger's length also is considered to give a good indication of how well the explosive is functioning. Many factors affect the density and velocity and have been thoroughly discussed by various authors (4, 6-12). For recording velocities several methods are available, but the resistance-wire, or probe, continuously recording technique has the distinct advantage of providing a record of the complete progress of an explosive reaction from the time it first initiates. Figure 1 is a copy of a typical record obtained by the procedure with certain significant information indicated. The theory and applications of the method are extensively covered in the literature so need not be reviewed for this report (13-18). Only the specific equipment and procedure employed for this investigation are presented.

Jan 1, 1973

By C. B. Manula

This report is volume 5 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Subsidence subsystem of the Master Design Simulator. This subsystem uses the finite element method to simulate ground movement caused by an advancing mining face in an underground coal mine. The model is structured around the concept that the ground mass is a layered media of different thicknesses and material properties. Gob areas are considered to be unfilled with broken rock at the beginning of mining. After mining starts, the gob areas are filled with broken material which provides resistance to the lowering of the overlying strata. The model is tied to the Geology and Reserves subsystem, but it can also operate as a free standing routine. A case study is presented illustrating the application of the model. A detailed user's manual, including a program listing, is included in the appendices.

Jan 1, 1974

By Dennis E. Jensen

Field studies were performed during blasting operations for strip coal mining above the room and pillar workings at Jenny mine in eastern Kentucky. The study is part of the Bureau of Mines program to develop criteria for the proximity of surface blasting to underground mines. Measurements and observations were made to identify physical changes in the mine. No change in the frequency of roof falls or any other indication of apparent damage was noted. Recordings of blast induced vibrations were made using sensors on the roof and floor of the underground mine and at the ground surface. A maximum particle velocity of 17.5 in/sec was recorded on the mine roof. The vibration data were analyzed and comparisons were made between roof vibration levels and those recorded on the mine floor and at the ground surface. Results are compared with previous blast vibration studies. Recommendations are made for further study toward developing criteria.

Jan 1, 1979

By M. Shamsuddin

Information on total estimated uranium reserves and domestic requirements have been collected, A survey has been made on the possibilities of recovery of uranium from low grade and complex ore deposits, e.g., marine phosphorites, shales, coal, sea water, etc. In order to assess the potential for uranium recovery from uraniferous phosphorites, available thermodynamic data of uranium minerals, compounds and aqueous species have been collected. The existence of uranium complexes with chloride, fluoride, carbonate, phosphate, sulfate, etc., in ground waters have been evaluated at different pH's. There seems a great need to study the relative stability of these complexes in order to judge the applicability of solution mining technology for selective leaching of uranium from phosphorites. A typical flow-sheet demonstrating recovery of uranium from wet-process phosphoric acid has been included in this report. Some essential features of the economics of uranium recovery from uraniferous phosphorites have been briefly considered and recommendation have been made for further studies.

Jan 1, 1980

By J. A. Kost

The objective of Contract J0295041 was to determine if the addition of a surfactant (wetting agent) to the water used for dust control in underground coal mines results in the reduction of airborne dust. Laboratory wettability tests, including the capillary rise test, a coal dust sinking test and zeta potential measurements, were used to select a coal seam/surfactant combination for in-mine testing. Four surfactants were selected for underground testing: Surfynol 465, Aerosol MA-80, DC-13, and Dustallay. The underground tests in the Lower Kittanning seam, Indiana County, PA, involved a Wilcox Mark 20 auger mining system, equipped with spray nozzles located on the cutting augers, Conflow venturi sprays, and a spray manifold. Respirable dust samples were provided by MSA Model G personal samplers and Simslin II instantaneous dust monitor; total airborne dust samples were provided by MSA Model G samplers with UNICO filter cassettes. Based on data obtained from 24 test periods surfactants, as compared to plain water, reduced the airborne respirable dust an average of 27 percent and total airborne dust an average of 36 percent.

Jan 1, 1980

By L. B. Phelps

A method is presented for the burial of potentially toxic spoil in high density zones or packages within spoil piles. Such burial could reduce the outflow of pollutants and thus minimize contamination of groundwater flows. Laboratory model studies using ammonium bromide tracer were performed to quantify the expected outflow mixing that could be achieved through package construction in spoils. Field drilling and geophysical density logging of spoils was carried out at three sites in Pennsylvania and Ohio to obtain a range of field spoil bulk density measurements and spoil samples. These data are analyzed to determine the relationships between spoil density and the controlling factors of lithology, depth, age, particle size distribution and mining method. A separate series of spoil permeability tests were performed in the laboratory to investigate the relationship between permeability and its related parameters. Research results are applied to the toxic package method to suggest guidelines for pack-age size, shape, density and placement for future field prototype development.

Jan 1, 1981

By Gilbert A. Wray

This report presents the results of a study of the overturning Stability of Front End Loaders and the development of an Obstacle Detector to warn of Obstacles in the blind regions of the vehicle. The contributing factors have been identified, the FEL stability characteristics have been determined and six overturn warning indicators were fabricated and two were field tested in a mine operation over an extended time period. A simplified overturn indicator, based on the principle of sensing wheel load, was designed, constructed and field tested. The principle was demonstrated to be sound, however, the method of sensing wheel load must be revised. An obstacle detector capable of detecting a man sized target at ranges of two feet to one hundred feet was designed. A "Breadboard" device utilizing existing microwave devices was constructed and tested successfully.

Jan 1, 1977

By Jules Gordon

Presents the results of mining tests conducted on a forward rotating bucket wheel excavator designed to continuously mine coal at 1080 tons/hour, Goals of the program are to determine the feasibility of the forward rotating bucket wheel principle as an effective means of reducing fragmentation and loading costs associated with surface mining, with additional benefit in reducing, coal preparation costs and stripping overburden. Tests took place at the Navajo Mine in Fruitland, New Mexico, Results show that the excavator performed as expected and can reduce fragmenting and loading costs up to 80°. Presented are: 1) production machine design specifications and projected economies extrapolated from the test data, and 2) recommendations for further work in dust control.

Jan 1, 1977

By G. M. Kintz

"Methods and costs of rock-dusting bituminous coal mines have been discussed in various publications by the United States Bureau of Mines and others.3 This paper discusses the present methods and cost of dusting at the Swastika mine of the St. Louis, Rocky Mountain and Pacific Co., Raton, N. M.In the Swastika mine the recommendations of the United States Bureau of Mines with regard to rock-dusting are followed at least as well as in any mine in the States of Wyoming, Colorado, and New Mexico. This mine is located at Swastika, N. M., approximately 4 miles west of the town of Raton and is in the Raton coal seam. The mine is rated as gassy and produces approximately 1,000 tons of coal per day.A mining system known as the ""room-and-pillar with cut-offs"" is used which results in recovery of nearly 100 per cent of the coal. The mine employs approximately 250 men.Ventilation is maintained by a Sirocco fan so arranged that the air current may be reversed and exhausting approximately 130,000 cubic feet of air per minute at 3 inches water gauge. This fan is supplemented by two auxiliary fans for emergency use. Three main entries penetrate the hill in a straight line for approximately 8,000 feet. The haulage is through the center entry, which is also used as the intake in conjunction with a two-compartment concrete-lined shaft located at the end of the entries. The main return for 3,000 feet inby the fan is 12 feet wide and 7 feet high. For this distance the ribs have been reinforced by a wall made of coke-breeze blocks plastered over with cement. Solid concrete blocks are used for the top row of blocks of the wall. Steel 10-inch I-beams spaced 40 inches apart center to center are supported on these solid blocks and thus support the roof. The next 1,000 feet inby has the same area, but the cement blocks extend to the roof, as no crosspieces are needed. The airways are kept clean and well rock-dusted.A rather unique system is used to handle gas feeders along the intake and haulage entries. There these feeders occur in the roof or where gas is apt to collect in high points along the haulage, tin funnels as large as 3 feet in diameter are placed near the roof. From these a 2-inch or other suitable-sized pipe is run into the return through the wall of the nearest break-through. A valve on this pipe line controls the amount of air pulled. These devices keep the high places clear of any gas, even when strong feeders are encountered.Fifteen-ton electric trolley locomotives are used on the main haulage and approximately 30 roller-bearing oars, each having a capacity of approximately 3,000 pounds of coal, compose a trip. All loaded tripe carry steel drags on the last car, and automatic derails are located at advantageous points throughout the mine.All loaded trips are thoroughly sprinkled on the sectional partings and at the main parting. The track is sprinkled every idle day, or if needed, every day; from a large tank mounted on a truck hauled by a motor. Neither nozzle nor spray is used, as these were unsatisfactory. The water leaves the tank. through a 11/2-inch valve and is permitted to flow on the road through a horizontal 11/2-inch T. Water is obtained from filling stations located throughout the mine. It is stated by the officials that the use of this method of sprinkling permits the entire haulage roadbed to be wetted down in two hours."

Mar 1, 1930

By Thomas E. Doerfler

Information and data related to the occurrence of fatalities due to major disasters in metal/nonmetal underground mines were analyzed. Standard statistical methods were used to estimate the probability of occurrence of major disasters, and to examine the relationship of disasters to injury statistics published annually.

Jan 1, 1980

By Ivan F. Avery

DOMESTIC production of carbon black increased 4 percent in 1962 to 2,056 million pounds. Furnace black output was 8 percent, or 132 million pounds, above that in 1961 and accounted for 90 percent of total carbon black production. Channel black output continued to decline and was 55 million pounds less than in 1961. Carbon black shipments during the year totaled 2,082 million pounds and were 5 percent above those of 1961. About one-fifth of these shipments were exported; the balance were sold domestically. An increase of 180 million pounds in domestic sales was partially offset by a decline of 80 million pounds in exports. Total value of carbon black production in 1962 was $145 million. The average value per pound of 7.06 cents was 0.24 cent per pound less than in 1961. Producers' stocks declined 26 million pounds during the year.

Jan 1, 1963

By M. Copeland

Phase relations of gadolinium alloyed, up to 40 weight-percent (wt pct), with AISI 304-type stainless steel were established. Body-and face-centered cubic iron-rich solid solution phases and several intermetallic gadolinium-containing compounds of variable composition that approximated the formulas Fe9Gd, Ni7Gd2, Ni3Gd, Fe2Gd, NiGd, and NiGd3 were identified. The intermetallic phases Fe9Gd and Ni7Gd2 were noted to melt at about 1,080° C at about 0 to 2 wt pct gadolinium. The melting temperature of Fe9Gd increased with increas-ing gadolinium content to a plateau at about 1,230°C and 30 wt pct gadolinium, and the melting point of Ni7Gd2 decreased to a plateau at 900° C and 30 wt pct gadolinium where Ni3Gd, NiGd, and Fe2Gd coexist. Body-centered cubic iron solid solution was stable from 1 to 2 wt pct gadolinium to higher contents, 30 wt pct gadolinium or possibly more, and face-centered cubic iron up to 12 wt pct gadolinium below 1,200° C. The stability of these phases above 1,200° C was not resolved except for the mel points. A limited number of fabrication variables as well as mechanical and corrosion properties of alloys containing up to 5 wt pct gadolinium were studied. Equilibrating and forming operations were best conducted at about 940° to 1,080° C. Some variability in the yield and tensile strengths of alloys was noted; however, there was a continual decrease in ductility and impact resistance with increasing gadolinium contents. The resistance of gadolinium alloys to corrosion in water at 354° C was about the same as stainless steel.

Jan 1, 1965