Search Documents

By Anthony T. Xannacchione, Luis E. Vallejo

At present, there is little knowledge concerning the shear strength of clays containing floating rock particles with concentrations from 0 to 30%. In practice, the effect of rock particles is typically disregarded in shear strength analysis The two primary reasons for this are: 1) a lack of agreement concerning the influence of rock particles on material strength, and 2) the expense and difficulty of testing day-rack mixtures with existing laboratory procedures. These factors have impeded the development of successful slope remediation design techniques far colluviums derived from resistant sedimentary rocks or spoil produced from surface mining. This study reviewed 3 1 technical papers which contain analysis of shear strengths for clay and sands with varying mixtures of rock particles. These technical papers, published over the last 40 years, are comprised of field case studies, laboratory evaluations, and theoretical analysis. Evaluation of this body of knowledge ha shown that the shear strength gradually increases with increasing percentages of floating particles in unsaturated clays.

By Basil Dimitriades

The roles of hydrocarbons and nitrogen oxides in smog formation were investigated by the Bureau of Mines. Samples of automobile exhaust with varying HC and NOx levels were irradiated in a smog chamber under conditions that resulted in smog levels similar to those observed in the atmosphere. Results were used to define the patterns that describe the dependence of a number of smog manifestations on HC and on NOx. Using these dependence data and some simplifying assumptions, estimates were made of the ranges within which HC and NOx must lie in order to obtain specified levels of air quality.

Jan 1, 1970

By P. J. Watson

The objective of this study was to prioritize the potential risks nuisance and biologically active dusts and fumes present in metal and nonmetal mines. This was accomplished by ranking numerical values derived from a matrix formula calculation that took into account dose, mine population, and sampling size. Data used in these calculations were obtained from the Mine Inspection Data Analysis System (MIDAS). The dusts determined to have the highest risk potential were quartz respirable particulates, mine dust, cristobalite respirable particulates, welding fume components, and nuisance respirable dust. Other dusts and fumes that were not ranked in this study, due to small sampling population, but which show a potential risk, include asbestos, talc, hydrogen cyanide, organic compound dusts, arsenic, metal dusts, and metal and nonmetal fumes.

Jan 1, 1987

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rim. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

By D. K. Denton, J. M. Girard, D. F. Scott, T. J. Williams

Personnel from the Spokane Research Laboratory, National Institute for Occupational Safety and Health, examined an underground pillar at the Homestake Mine, Lead, SD. Investigations involved strain relief and seismic tomography studies in the mine, and ultrasonic velocity measurements on pillar core in the laboratory. Measured octahedral normal stress was 37 MPa (5,366 psi); seismic P-wave velocities averaged 5.2 km/s (17,060 ft/s); and ultrasonic velocities at a pressure of 39.6 MPa (5,750 psi) averaged 6.3 km/s (20,669 ft/s). The difference between in-mine and laboratory velocities is attributed to the attenuation of seismic energy by mine fractures larger and more numerous than those in the samples of core measured in the laboratory. Using these results, researchers hypothesize that pillar rocks have the ability to withstand stress an order of magnitude greater than they currently sustain.

By G. W. Jones

In cooperation with the Edison Electric Illuminating Co. of Boston, Mass., and the-Boston Consolidated Gas Co., the Bureau of Mines, United States Department of the Interior, has conducted a survey continuously since 1929 to determine the general hazards of combustible gases and vapors in manholes of the Edison Electric Illuminating Co.

Jan 1, 1942

By G. W. Jones

In cooperation with the Edison Electric Illuminating Co. of Boston, Mass., and the-Boston Consolidated Gas Co., the Bureau of Mines, United States Department of the Interior, has conducted a survey continuously since 1929 to determine the general hazards of combustible gases and vapors in manholes of the Edison Electric Illuminating Co.

Jan 1, 1942

By Clayton M. Rumsey

The U.S. Bureau of Mines conducted a mineral resource survey of the Cinder Cones Wilderness Study Area (WSA) (CDCA-239), 10 miles east of Baker, CA, in 1983. The 44,299-acre WSA is underlain by Precambrian granite gneiss, Upper Cretaceous or lower Tertiary Teutonia quartz monzonite, and Quaternary basalt flows and alluvium. This mineral survey included an examination of two volcanic cinder mines, five lode prospects, two volcanic cinder prospects, and reconnaissance sampling in and near the WSA. The seven prospects are in the WSA; the two volcanic cinder mines are adjacent. No mines are in the WSA. In 1981, there were 61 placer and 3 lode mining claims in the WSA. Sample results from two prospects within the WSA contained significant gold and silver values; however, the mineralized rock is of limited extent and no resources were apparent. Alluvial samples taken throughout the WSA contained only traces of gold. Two volcanic cinder cones within the WSA contain an estimated 30 million tons of cinders. There are sufficient cinders outside the WSA to satisfy demand in the foreseeable future. Stone, sand, and gravel deposits are not resources because similar material is closer to markets. No evidence of energy minerals or geothermal resources was found.

Jan 1, 1985

By Thomas E. Finch

This report is a continuation and expansion of a previous USBM grant (No. G0254004) which examined alternative methods of handling the parting between two coal seams in a surface mining operation. The alternative methods consist of equipment implementation in either a stowing or haulback technique. Following a typical strip mine conformation, the parting is directly stowed or hauled back and placed in the pit bottom after second seam removal. The objectives are to produce an environmentally sound material placement technique and to increase prime stripping machine utilization. This report contains the engineering philosophy behind two computer programs created to evaluate parting handling methods over d wide range of coal and parting thickness ratios. The nature of the computer approach allows cost sensitivity analysis and quick updating of costs. The two programs are clearly presented with documentation and examples such that consumers may apply then to their own operations.

Jan 1, 1977

Two coal seams were selected and the conceptual designs were based on the geological and physical conditions typical of these seams. As a result of the screening process presented below, the two coal seams selected were the Lower Kittanning Seam in central Cambria County, Pennsylvania and the Pittsburgh Seam in northwestern West Virginia and southwestern Pennsylvania. SELECTION PROCESS FIRST SCREENING OF LONGWALL OPERATIONS The list of longwall operations prepared in Phase I and included in the Phase I report, was used as the basis for a first screening. From this list it was determined which longwall operations were not in the Appalachian coal fields and not in a coal seam of the thickness range of 42 to 72 inches. The first screening eliminated 30 of the listed operations, leaving 48.

Jan 1, 1976

By C. A. Komar

The Bureau of Mines conducted oil-displacement tests in the laboratory with three water-in-oil and five oil-in-water emulsions that were created with ultrasonic energy at a frequency of 20 kHz and an acoustic intensity of approximately 100 watts per cm2. Emulsions of either crude oil or kerosine, brine, and 112 to 2 percent emulsifier were formed during 30 seconds of acoustic irradiation. Results indicate that ultrasonic energy induces greater and more uniform dispersion of one liquid in another in the presence of small amounts of chemi¬cal emulsifiers. When the emulsions were injected as a buffer slug before waterflooding, recovery of the oil-in-place was 8 to 22 percent greater than with conventional waterflooding in the test specimens, regardless of the con¬tinuous phase (oil or brine). The emulsions do not appear to be applicable to the Appalachian area; however, because the oilfields are too "tight," the clays in the formation remove the emulsifier from the displacing fluid, and not enough additional oil is produced, compared with recovery using conventional waterflooding, to warrant the increased operating costs.

Jan 1, 1969

By Gary Friedline

As a consequence of the Coal Mine Health and Safety Act of 1969(PL91-173), the Bureau of Mines (BOM) entered into a contract with Ocean Energy Inc. (OEI) to develop, fabricate, install, and evaluate a permissible lighting system for use on a longwall coal mining operation. The program schedule is shown in Figure 1.1. The proposed regulations are contained in Appendix A. The initial part of the program involved a survey of existing longwall lighting practices in Germany and England and an evaluation of a variety of lighting components on a mockup of a longwall mining operation that was fabricated under this program. Visits made to German and British mines uncovered major differences in lighting level requirements, permissibility aspects, size, and operating constraints which identified wide disparities and essentially eliminated from further consideration any known imported lighting devices for meeting the higher lighting levels and standards proposed for US coal mines by the Mining Enforcement and Safety Administration (MESA). The longwall mockup provided use¬ful information regarding the amount of illumination required, physical size and shape of lamps, light distribution problems, cable routing, use of connectors, signaling, glare, and other important factors unique to the lighting of low coal longwalls.

Jan 1, 1975

By Henry M. Harris

A study was made by the Bureau of Mines to determine if shapes of oxide-glass compositions could be roll-formed at high temperatures, and to find the conditions required for adequate formability. A unit with directly connect' furnaces and heated rolls that allowed forming of most of the compositions developed. Glasses of the feldspar type were chemically unreactive with the alumina grains, and allowed the best roll forming. Optimum forming was attained at temperatures of 1,400° to 1,530° C, with compositions containing 30 or 40 percent feldspar and 60 or 70 percent alumina. Formability was better when compositions contained minus 325-mesh materials, rather than coarser or finer powders. In many cases, roll-formed shapes had physical properties equal to or better than the normally sintered shapes of the same composition.

Jan 1, 1967

Electrical trailing cable used to power coal mining machinery is frequently damaged by tensile strain or crushing by mining machines running over the cable. A major problem is finding the exact location of a short or open in this cable so it may be repaired. A major problem is finding the exact location of a short or open in this cable so it may be repaired. FMC Corporation was awarded modification III to USBM Contract H0122011 to continue development and testing of cable fault locators, resulting in delivery of: 1. A prototype electrostatic/electromagnetic/ TDR transmitter and an electrostatic/electro-magnetic receiver sot that: o Locates cable faults by time domain reflectometry o Locates opens by detecting electrostatic signals o Locates shorts by electromagnetic coupling. 2. A prototype infrared detector and an infrared detector power supply that heats a shorted area by applying high current (at low voltage) and locating a short by infrared output. 3. Twelve production infrared detectors. 4. Detail drawings for all of the developed instruments.

Jan 1, 1973

By L. G. Marshall

This report describes dredging and processing of sand and gravel from a glacial-fluvial deposit in the Raccoon River valley near West Des Moines, Iowa. Preliminary cleaning and separation of the sand and gravel at the dredge site with subsequent transportation to separate plants and the production and disposal of the various grades of aggregate material are also described. The geology of the deposit is summarized. A tabulated summary of costs in units of labor, power, and supplies is included.

Jan 1, 1963

By Frank E. Cash

The work of the United States Bureau of, Mines is concerned primarily with the prevention of accidents in the mining, petroleum, and allied industries. This report analyzes the fatal accidents in the coal mines of Tennessee and gives the pertinent factors in tabular and descriptive form, with interpretations and suggestions to operators, workers, and the State Division of Mines for the future prevention or reduction of accidents in coal mines. ACKNOWLEDGMENTS This study was made possible through the cooperation of A. W. Evans, chief mine inspector of Tennessee, and his secretary, Miss Hiliary Penny, who made available the department records and assisted in the segregation and assembly of the data.

Jan 1, 1935

By D. Harrington

This circular presents Part III-A of a series reviewing the literature on effects of breathing dusts with special reference to silicosis; it deals with the economic and legal aspects of dust diseases in industry; Part III-B will contain data on the status and cost of compensation for silicosis, Parts I and II of the series have been issued as Information Circulars 6835, 6840, and 6848; Part I defines and classifies dusts, indicates sources of exposure, and describes the physiological effects of breaching dusts; Part II-A discusses the principal dust factors producing pulmonary pathology and methods of determination of dust in air; and Part II-B presents data on the engineering and medical control in the prevention of dust diseases and general recommendations for their control in industry. A summary and general conclusions will complete the series.

Jan 1, 1935

By G. F. Kuncir

The time-cost-risk analysis described herein was performed as part of an evaluation of the Advancing Oil Shale Mining Technology Program performed by The Aerospace Corporation. The objectives of this analysis are to assess the feasibility of the program relative' to time and cost constraints, and to determine the probabilities of achieving various technological goals. A combination of standard program planning and analysis techniques were used to achieve these objectives. These included a critical path analysis, a resource allocation analysis, and a risk analysis.

Jan 1, 1977

By Michael Rieber

Commodity transportation by barge is possible on about 25,000 miles of navigable inland waterways in the contiguous 48 states. Barge operations are used chiefly for the movement of bulk raw materials ranging from farm products to iron ore, coal, and other bulky semi-finished as well as finished products such as steel, chemicals and petroleum [3,p.7-9]. The barge industry, unlike other transportation industries, is largely unregulated. This is because all liquid bulk commodities most dry bulk commodities transported by for-hire carriers and companies engaged in private transportation of their own commodities are exempted from Interstate Commerce Commission regulations. As a result, about 15 percent of the total ton-miles of barge traffic each year is under Interstate Commerce Commission regulation [13,p.14-25].

Jan 1, 1977