Search Documents

By Robert F. Dexter

This paper discusses the Federal requirements of this regulation for the importation, manufacture, distribution and storage of explosive materials. The interstate or foreign commerce in explosive materials, licensing of manufacturers, importers and dealers, issuance of permits, the conduct of business by licensees and operations of permit tees and the storage of explosive materials.

Jan 1, 1975

By Frank Sames

Where applicable, high production benches can improve efficiency in quarrying. Quality control, geological, cost or other considerations might result in the development of quarry benches higher than 30 m (»100 ft) and sometimes up to 60 m (»200 ft).

Jan 1, 1996

By Michael S. Stern, Gordon P. McDonald

The increasing costs and problems associated with transporting and safely disposing of used engine oils from remote mine sites have caused mining companies to consider other ways to consume their used oil. One practical method of disposing of these used oils is to blend them with the diesel component of ANFO and Heavy ANFO type explosives.

Jan 1, 1993

By I E. "Chip" Harris, G Alan Foster

Whilst a great deal of published data exists as to safe ground vibration and air blast levels which result from blasting little documented research has been carried out to determine how and why human beings complain about blasting operations. This paper gives the authors thoughts and experiences of why complaints arise and practical steps to minimize such complaints.

Jan 1, 1977

By Erik Nygaard

During the last years, ammonium nitrate has been involved in several accidents worldwide. This have caused increased focus on security and safety issues and resulted in:• Revised Yara standards • Revised international standards for storage and transportation • Stricter regulations from national authorities in many countries.

Jan 1, 2008

By Edward Jr Walter

This paper discusses the problems that arise in the process of developing adequate explosives noise legislation. Case histories are used to illustrate how and where these problems arise and the course of action followed in overcoming them. It is imperative that those concerned keep informed as to possible legislation and be prepared to present solid facts that will insure fair and reasonable controls.

Jan 1, 1975

By Roy Rose, Bruce Bowles, Wesley L. Bender

Numerous large diameter water wells are used to dewater the pit at the Sleeper Mine. Occasionally, a well will be located inside the boundaries of a blast. Although one might expect that wells so located would become inoperable due to blast-induced damage, in most instances this has not proven to be the case.

Jan 1, 1991

By Steven P. Case

To meet salt production needs over the remaining life of the Cayuga Mine at Lansing, New York, the Salt Division of Cargill, Inc. decided to build a new underground screening plant. The new plant required a chamber 50 feet wide by 250 feet long and nearly 70 feet high. On advise of their mining contractor, Dynatec Mining Company, the company chose an ingenious excavation method similar to sublevel stoping. This method eliminated the need for an access ramp, reduced equipment needs and excavation time substantially.

Jan 1, 1996

By Justus Deen, Paul V. Sterk

Through the 119 year history of the Homestake Mine various methods of raise mining have been used, these include conventional, bored, and drop raises. These raises provide passage for men and supplies, provide ventilation, transfer broken rock from level to level, and serve as emergency escapeways. As the 1980s came to a close, many of the larger ore bodies in the mine had been mined out. This has resulted in many crown pillar situations that required a method to mine them. In addition, the Homestake ore body also contains numerous ore reserves that have short vertical height. The ore itself can be from vertical to 50 degrees in dip. Due to the high cost of drift and ramp development many of these ore bodies are sub-economic using conventional mechanized cut and fill mining.

Jan 1, 1996

By Thomas M. Keevin, Gregory L. Hempen

A study was conducted to measure underwater pressures associated with confined borehole shooting used to remove rock for The Kill Van Kull Deepening Project, U.S. Army Corps of Engineers, New York District. A major natural-resource-agency concern was the potential for fish mortality during explosive rock removal. Currently, fish mortality models are based on testing programs that exposed captured organisms to open-water blasts. Natural resource agencies, without in-house explosive engineering expertise, generally are not familiar with the physical properties of blasting underwater. Confined shots are most often used for demolition and rock removal underwater. Pressure amplitudes from confined blasts are significantly reduced as compared to open-water blasts that, are commonly used for fish testing The duties of natural resource agencies are made even more difficult by the lack of published data on pressures associated with confined blasting. As a result, explosive weights for confined shots mistakenly have been used to run mortality models that were developed using open-water blast pressure data. This study was conducted to collect pressure measurements during rock removal for the KVK deepening project and compare those data with computed peak pressures for open-water explosions.

Jan 1, 2005

By Mike Wheat, Catherine Aimone-Martin, Brandon Pease

The Kneeling Nun rock pinnacle is a prominent landmark, 90 ft in height and 35 ft in width, that resides on a bluff overlooking the Santa Rita pit at the Chino Mines Co. operations near Silver City, New Mexico. The company plans to expand the current pit limits, resulting in a change in direction and distance of hard rock mine blasting operations in relation to the pinnacle. Concerns about the stability of the pinnacle adjacent to mining activity has prompted company personnel to enhance the seismic monitoring program both on the pinnacle and along the current open pit highwall that forms the base support below the pinnacle foundation. This paper presents the vibration response characteristics of the pinnacle, in terms of amplitude and natural frequencies of motions and damping characteristics, for measurements recorded at the top and base of the pinnacle. The influence that blasthole initiation timing and sequence of hole detonations have on vibration response is discussed. A simple analysis is made to estimate factors of safety against cracking of the landmark as well as blast-induced slope instabilities within the foundation rock.

Jan 1, 2000

By Gungor Tuncer, Ali Kahriman

"In bench blast design, not only the technical and economical aspects, such as block size, uniformityand cost, but also the elimination of environmental problems resulting from ground vibration and airblast should be taken into consideration."

Jan 1, 1999

By C. B. Navalkar

The optimization of blast design under consideration is for the conventional driveways in under ground coal mines with respect to board & pillar workings in India. Basically The Blast Design includes following parameters: AA> Drilling Pattern. BB> Charging Pattern. CC> Material & Method Of Stemming. DD> Selection of type & quantity of explosives. EE> Initiation system & Blasting Sequence.

Jan 1, 2002

By Katherine L. Heineken, Timothy J. Tope, Kim David Murphy

One method for small arms disposal is the use of a deactivation furnace or explosive waste incinerator. There are numerous hurdles a facility typically encounters to get the furnace or incinerator fully operational and permitted. For example, one Department of Defense installation was in the permitting process 7 years, which included numerous facility upgrades and modifications. This paper will discuss the technical approach for proactively addressing permitting issues and requirements and will identify potential pitfalls to avoid as well as ways to reduce costs. For example, when determining the waste profile, the facility should forecast its treatment needs (taking into account the net explosive weight limits of the furnace/incinerator) and then classify the wastes into "chemical families" based on the type and composition of the wastes. One waste from each family should then be selected for potential inclusion in the trial burn. Modeling the waste disposal can help to narrow down the number of wastes requiring characterization during a trial burn, as well as the number of analyses.

Jan 1, 1997

By W. Reisz

Dealing with misfires can be one of the most difficult and serious issues that blasters must confront. Most of us will - at some point, have to deal with a misfire situation.

Jan 1, 2009

Vibration resulting from blasting has been a source of concern from the inception of the use of explosives. As a result many investigations have been made concerning the seismic effects of blasting and at present there is available an adequate set of standards with which to judge seismically the damage capability of a blasting operation.

Jan 1, 1976

By David Lilly

The introduction of electronic caps with significantly more precise timing is forcing an examination into the practical effects of timing precision upon vibration, air blast, fragmentation and crusher productivity. These investigations have produced suggestions that techniques using multiple delays of the same period with conventional detonators might approximate electronic high precision.

Jan 1, 2006

By R Wing, D Corkery

"Several mines in the region of Sudbury, Ontario, occur in or near populated areas. In anattempt to examine the effects of environmental changes and blast induced vibrations onhomes in the area, a monitoring study was conceived. The study was conducted fromNovember 1990 to May 1991 in homes located near the 880 Stope at INCO Ltd.'s CopperCliff South Mine."

Jan 1, 1993

Increasingly specialized blasting needs require that the explosive energy available in a borehole be reliably known for representative blasting conditions. The underwater test, when properly performed, can yield such information and thus provide a reliable rating of explosives in terms of energy release. This paper reiterates the stringent experimental conditions to be satisfied, and data analysis and interpretation techniques to be followed to achieve this. This is supported by detailed experimental studies involving select parameters in both detonator and booster sensitive explosive compositions. The paper also illustrates the inadvisability of equating blasting performance with the commonly calculated energy values.

Jan 1, 2000

By Bruce B. Redpath, Thomas E. Ricketts

Scaling laws commonly used for describing or predicting blast motions generated by conventional arrays of blastholes are dimensionally incorrect. The scaling of distance by the cube root of charge weight is correct only for spherical charges, and scaling by the square root of charge weight is incorrect for any charge configuration, although both approaches may result in empirically useful formulas for a limited range of charge sizes. Analysis of motions generated by a large set of underground blasts shows that scaling distance by the square root of the linear charge density, which is dimensionally correct for a cylindrical borehole, yields much more consistent results than the traditional scaling rules. Further, this scaling law is valid right up to the free face of the burden. A significant result of this work is that the peak particle velocity for an array of blastholes is primarily dependent on blasthole diameter and not on total charge weight or maximum explosive weight per delay, which are the commonly used parameters for scaling seismic amplitudes generated by conventional blasting arrays.

Jan 1, 1987