Search Documents

By Andre Pinsonnault, Francois Lefebvre, Yves Newman

In 1989, Les Entreprises Kiewit Ltee signed a C$32 million contract with the Societe d'energie de la Baie James, on behalf of HydroQuebec, to excavate the intake and tailrace channels for a second powerhouse at the LO-2A James Bay hydroelectric project. The multistage contract included removing three marine rock plugs. The first plug was blasted in April 1990. It was a 43 yards wide, triangular shaped wedge that projected into 18 yards of water. Located at the mouth of the intake channel, it contained over 72,000 yd3 of rock, more than twice the 30,000 yd3 found in most rock plugs.

Jan 1, 1991

By Joel Warneke, Cristian Caceres, Ed Mchugh

NIOSH researchers collected basic data from two blast rounds at the SSX-Steer Mine as a component of a larger study on controlled blasting, the goal of which is to reduce injuries from falling rocks in underground mines. Drilling and blasting procedures at the mine were observed. Rock mass property data were collected, a program of seismic monitoring and analysis was conducted, and 3-D laser survey scans of the workings before and after each blast were performed. The geologic data showed that the rock mass quality was characterized as poor to very poor. It was essentially uniform within the panels examined. The recorded seismic data indicated that fill material acted as an effective damper to seismic energy. The pre- and post-blast laser scans showed both over-break and under-break conditions, highlighting the problems associated with blasting a weak rock mass. By comparing the achieved results to the intended design, potential improvements in the drilling and blasting practices can be identified. Comparison of these data with similar data from other mines will help define how various combinations of rock and fill behave during blasting. Through studies such as these, data collection procedures and analysis techniques can be refined. An ultimate goal is to develop blast procedures tied to rock mass characteristics that can minimize damage to rock in the perimeter of the opening, limiting the amount of loose rock and improving the safety of miners.

Jan 1, 2008

By Michael Wieland

Smoke/fume measurements from rapid transitory charge reactions are not wholly comparable with thermodynamic reaction code (TDRC) results, since quenched chemical reactions yield nonequilibrium concentrations. Though the work output and major reaction products are usually rendered with minor deviations, the toxic fumes and other minor concentrations reveal some major discrepancies. Work output for charge formulations in underwater or fixture tests were theoretically resolved with work-principal models that form a rough thermodynamic trajectory. Stalled nonequilibrium concentrations are rationalized by finding the underlying quenched reaction(s). The wide relevance of the Zeldovich radical-chain mechanism that transforms nitrogen oxide was previously recognized. The work-principal model (WPM) represents reaction quenching with off-trajectory constraints to render the fumes, without noticeably readjusting the work process. When restraints that characterize the confinement are WPM tractable, the resolution of critical reaction mechanisms is worthwhile, since they remain useful, regardless of the rich, neutral or lean stoichiometry of the charge formulation.

Jan 1, 2012

By Randall M. Wheeler

Many blasting companies are using simulated production ground vibration waveforms to aid them in the control of their vibration effects. The simulations are typically produced by using a seismograph to record a signature waveform from a single hole shot and subsequently applying the various delays to be used in a proposed production design. The ability of this simulation method to give good results usually depends on three primary factors. These are: 1) the homogeneity of the seismic travel path from hole to hole; 2) the consistency of the seismic energy release per unit of explosive from hole to hole; and 3) whether or not the delays fire as planned.

Jan 1, 1991

By Michael Swisdak, John Tatom, James Tancreto

In 2002, testing was proposed to generate needed data to assist in developing improved explosives safety standards within the US Department of Defense. This testing emphasizes two major areas: (1) full-scale donor/acceptor trials examining debris generation and acceptor response and (2) debris perforation testing of representative roof/wall materials. The full-scale donor/acceptor trials are referred to as the SciPan series. The first three tests in the SciPan series have been completed, as has the first phase of the SPIDER program. This paper describes the status and future of these testing programs, reasons for choosing specific tests, potential benefits, and planning for future phases.

Jan 1, 2006

By Alan Bauer

During the past several years, the trend to large-diameter blastholes in both open pits and underground mines along with the continuing developments in slurried explosives and delay systems has kept things exciting for the drilling and blasting engineer. This has been particularly so in underground mining, where new mining systems having lower cost and higher productivity have emerged. Crater technology has produced new large-scale methods for resisting front penetration in tar sand mining and also new underground retreat mining methods and methods of raising.

Jan 1, 1978

By Takeo Ueda, Masashi Nakano

We have developed a new blasting system remotely controlled by an electromagnetic firing method, which has proved advantageously applicable to sites where rapid tidal current or deep water may cause serious troubles in underwater blasting operation by a conventional method.

Jan 1, 1983

By Peter Cameron, Tom BoBo

Comminution, being the energy intensive part of a mining operation receives much scrutiny by cost controllers, CEO’s, investors and others as the mining industry goes “back to basics” to reverse the decline in productivity which occurred during the mining super cycle.

Jan 1, 2019

By Greg Wyartt

Although electronic detonators and blast initiation systems have been commercially available for several decades, uptake in the Australian mining industry has been very slow when compared to other global mining regions. The safety and operational advantages of electronic initiation are generally well understood in Australia, however there has been a prevailing perception that these advantages do not outweigh the extra financial and technical investments.

Jan 1, 2019

By AJ Rorke

Blasting trials using Daveytronic Electronic Delay Detonator systems (EDD’s) were conducted at the Alpha Ferro Quany (Pretoria) and the Eikeboom Colliery near Witbank in November 1999. The objectives of the trials were to determine the influence of accurate hole firing on rock fragmentation, blast-induced vibration and blast throw. This paper provides an outline of the trials and an analysis of the results. The results were compared with a normal shock tube initiation system. Fragmentation was measured using video-imaging techniques at the hard rock Ferro Quarry for one conventional shock tube blast and two EDD blasts. No significant difference was measured in the fragmentation between the shock tube blast and the two electronic detonator blasts. Joint planes mostly defme the fragments at Ferro Quarry. The fragment sizing was therefore controlled mainly by the rock structure and the blast timing appeared to have no influence. Vibration measurements made at Ferro Quarry indicate that electronic detonators have a marked effect on vibration frequencies compared to shock tube systems. The more accurate detonators resulted in a narrower f+equency band at lower amplitude with similar timing. By modifying the blast timing, the dominant frequencies were changed. The electronic detonators had a significant positive influence, therefore on blast vibration and its control. The timing scatter measured from the shock tube blast was considerable, with measured inhole detonator scatter at 48 ms over a sample of 19 units. Surface delay periods less than 42 ms would therefore not be able to provide effective sequential firing. The scatter of the Daveytronic units was below the 2 ms resolution of the high-speed camera used to film the blasts. Reliable sequential firing, even at very short delay intervals was considered the main reason for notable improved throw in an overburden blast at Eikeboom Colliery. Blast throw was improved by 25% for the test blast.

Jan 1, 2000

By John N. Jr Edl

Geokinetics, Inc. has pioneered an in-situ oil shale retorting production process that provides the requisite void space for producing a permeable rubble bed, within the retort zone, by using the explosive energy from vertical blastholes to lift the overburden. By installing suitable instrumentation on the surface of the overburden over an appropriate blasting pattern, it is possible to obtain estimates of the average radius of gas penetration around the blasthole and the average volume, per unit length of blasthole, that is actually occupied by the explosively produced gases (which includes both the volume of the cracks that are penetrated by the gas pressure and the deformed blasthole volume). It is expected that these estimates can be used to examine, and quantify, the effects of such blast design parameters as the type of explosive, the blasthole diameter, the geometry of the explosive charge (length to diameter ratio), and the relative timing of sets of charges.

Jan 1, 1983

By Dale Preece, Vanessa Berg

This paper presents a two-pronged vulnerability analysis approach for treating minimally reinforced concrete (RC) structures subjected to explosive events. This work was motivated by a heightened interest in homeland protection involving both malevolent and accidental explosions and the need for assessment of critical facilities subjected to an explosive detonation. The first part of the analysis approach employs the commercial 3-D Eulerian-Lagrangian hydro-code AUTODYN, while the second part of the analysis employs Single-Degree-of-Freedom (SDOF) methods, each predicting the dynamic response of the minimally RC walls, slabs and columns to explosive loading. The concrete is treated with the newly developed RHT (Riedel, Hiermaier, Thoma) constitutive model, which accounts for failure mechanisms in brittle materials. Predictions from AUTODYN are verified using the equivalent SDOF reinforced concrete code, SPAn32, developed by the US Army Corp of Engineers and agreement between the results indicates a high level of accuracy in both methods of analysis, allowing for accurate predications of airblast-structure interactions and failure mechanisms.

Jan 1, 2004

By Sterling Ziegler, Kameron Ray

Mining operations at a Wyoming coal mine were progressing to within 300 feet (91 meters) of a high pressure natural gas pipeline. Vibration levels from cast blasting were at a point at which standard designs would exceed permitted limits and could potentially damage the pipeline. Without a confident vibration model, mining would be unable to continue in the pit rendering an entire cut of otherwise mineable coal sterile. To safely blast in the area, linear superposition seedwave analysis techniques were attempted to be used to create a model that could accurately predict the vibration at the pipeline. Four signature holes were fired individually. The four signature waveforms were monitored at eight discrete locations to create thirty-two vibration data points. Two of the monitors were equipped with triggers enabling the calculation of p-wave velocity.

Jan 1, 2018

By M E. Hanson, K Chong, R H. Jacobson, S C. Way

To create conditions for economic rates of mineral recovery in a deep, hard rock mass, enhancement of naturally occurring permeability is necessary, and may be achieved through explosives detonated in boreholes. Previous theories of explosively created permeability are reviewed and found to relate permeability solely to the degree of fracturing, neglecting porosity. A theory is presented that includes both fracture density and porosity, and its results are applied, together with a knowledge of explosive behavior, to derive design parameters for in-situ mining.

Jan 1, 1983

By Dworzak, Andrzej Biessikirski, Jozef Pyra

During the detonation process 20-30% of the energy is being consumed only on the quarrying pro-cess. The remaining amount of the energy generates harmful effects such as: shock wave, acoustic wave, fly rocks and ground vibrations. The ground vibrations effect is the most dangerous especially to structures which are situated nearby an open pit mine.

Jan 1, 2015

By Kenneth Medearis

There is considerable evidence that more rational damage criteria need to be generated with regard to low-rise structures subjected to blasting vibrations. There is not sufficient basis for specifying a maximum ground particle velocity damage criterion such as 2 inches/second. A peak ground velocity guideline does not currently take into account a number of significant parameters, including the predominant frequencies of the ground motion excitation and the structure being excited. Although a number of states have adopted, or are adopting, maximum particle velocity criteria, such criteria have been ruled inadequate in certain legal decisions affecting blasting operations. The development of more rational damage criteria is thus of significant importance.

Jan 1, 1978

By James Goldberg, Sally Zadra, Wiliam Reisz

Early recognition and risk assessment is critical to sustaining a safe and productive blasting operation. While every blasting environment holds inherent risk, highwall blasting in highly congested areas such as Hanson Material Service Corporation’s Romeoville and Thornton quarries in the greater south Chicago metropolitan area can be particularly perilous

Jan 1, 2008

By Dave Harrison, Phyllis Hasser, Ken Eltschlager

The beginning There was the video:– “Understanding Vibrations from Blasting” – 2002 to 2004 in development – Dale Ramsey ad hoc Public Education committee chair – Available At the ISEE bookstore Public Education and Public Relations Committee • Standing ISEE committee 2004 • Co-Chairs – Ken Eltschlager, Dave Harrison • Purpose: "Develop and conduct programs on public education and public relations. Public education programs will focus on public awareness, understanding, and appreciation of the explosives industry. Public relations programs will concentrate on providing blasting professionals with the tools to assist in the public's understanding of the explosive industry and in the appropriate ways to respond to local community issues."

Jan 1, 2007

By Robert L. Martin, Brian W. Stump, David P. Anderson, David Gross

In an attempt to better understand the impact that large mining shots will have on verifying compliance with the international, worldwide, Comprehensive Test Ban Treaty (CTBT, no nuclear explosion tests), a series of seismic and videographic experiments has been conducted during the past two years at the Black Thunder Coal Mine. Personnel from the mine and Los Alamos National Laboratory have cooperated closely to design and perform experiments to produce results with mutual benefit to both organizations. This paper will summarize our activities, highlighting the unique results of each.

Jan 1, 1997

By Piyush Rai

Proper use of fi ring pattern vis-à-vis the blast requirements can provide optimal blast performance in terms of fragmentation. Further to this, each fi ring pattern has its own characteristic, for instance, although V-type and diagonal fi ring pattern provide same Se/Be ratio, the V-type fi ring pattern increases the opportunity for in-fl ight collision amongst broken rock fragments during their movement. Similarly straight V-type and skewed V type fi ring patterns (V1,V2 etc.) have their own characteristic strengths and weaknesses. In this light the present paper highlights the application of three different types of fi ring pattern on two different type of sandstone overburden benches of a large coalmine in India. The study reveals that Firing pattern infl uences the effective spacing to burden ratio at the time of detonation. By changing the fi ring pattern, effective burden (Be) changes and the ratio of effective spacing (Se) to effective burden (Be) during the fi ring is also subject to change in comparison to drilled spacing to burden ratio (S/B) Hence, the Se/Be ratio vis-à-vis fi ring pattern must be used to design the blast rounds. The results have been derived on the digital image analysis based fragment size characterization, excavator performance and evaluation of powder factor values on blasted muck piles. Skewed V- type fi ring yielded the best results in comparison to straight v-type and normally practiced diagonal fi ring pattern on the moderately strong sandstone benches, whereas, the existing diagonal fi ring pattern appears to be satisfactory on weak (weathered and gritty) sandstone benches. The presence of geological anomalies has also been investigated.

Jan 1, 2008