Search Documents

By Bill Rose, Alan Foster

This paper will outline blasting as undertaken at the Flour Mill project in the Georgetown area of Washington, D.C. It will discuss the vibration and blasting problems found in blasting in high risk and highly populated areas, and the day to day methods used to minimize damage potential and still maintain adequate fragmentation.

Jan 1, 1979

By Stephen Mansfield

Analysing how accurately a blast design is implemented is one of the cornerstones of a successful operation, and critical for mine optimisation. This paper presents a concept that involves the collection and analysis of data for the five stages through which a blast transitions, from budget through to implementation.

Feb 1, 2020

By Charles Clark, Mark Mukhija, Jaime Klein

Comminution – the reduction in size of solid materials – is the most energy intensive component of the mining process (Bauer, 2015). It is estimated that comminution consumes around three percent of all electricity generated in the world (Ceecthefuture.org, 2017). On an energy equivalent basis, downstream processing consumes six times more energy than drilling and blasting (Kanchibotla, Sarma et al., 2014).

Jan 1, 2018

By Julio Cesar Barbosa de Freitas, Rafael Gonçalves Araujo, Túlio Soares, Jair Koppe, Augusto Ferraz Ribeiro, Pedro Barreto Garcia

This study thesis was motivated by the fact that it is of fundamental importance for open pit mining that the slopes initially have a geometry in accordance with what is proposed in the mining planning. This occurs because an inconsistency in this design can impact the operational safety and economic solutions of the mining project. These consequences can be explained by the fact that rock blasting close to mining limits requires specific study due to the attention required. Because, when this operation is not carried out properly, the mining plan in the mine may not be respected and may create risks to the operation due to the presence of unstable blocks on the slopes (Mackenzie). In this sense, Mackenzie (2004) cites pre-split, trim blasting and buffer as commonly used explosive blasting techniques that aim to limit damage beyond the projected wall. Therefore, Enaex Brazil realized the need to better understand the pre-split method. To do this, it is necessary to understand how the energy released during detonation is perpetuated in the rock mass when this technique is used and when it is absent. Thus, this analysis is based on a seismic study that allows the creation of vibration attenuation laws and an elementary wave damage model, which allows the local characterization of the rock. With this model it is possible to relate the peak levels of vibration during blasting and the extent of damage, but a critical level of vibration (PPVc) and its relationship with the Uniaxial Comprehension Resistance (UCS) are also defined for the start of fracturing and its level (McKenzie et al, 1995). And, mainly, this work aims to address a way to measure the pre-split filter potential by comparing the attenuation law with and without pre-split, ultimately knowing whether this finishing blasting is being effective, to understand the pre-split filter capacity.

Jan 21, 2025

By Hernan Navea, Carlos Alvarado, Exequiel Nuñez, Matías Suarez, Jhon Silva, Bryan Townsend, Bryan Caceres, Felipe Pontanilla

Nowadays, technology dominates all aspects of human activities, and drilling and Blasting (D&B) is no exception. In most cases, the use of technology in D&B is focused on controlling individual activities such as drill performance, drilling advance rates, truck loading performance, etc. Still, in very few instances, the advantages of using technology along each D&B activity and how this influences the D&B results are documented. This paper shows how technology is applied to create a “relative hardness” model for the mine Caserones in Chile. In the future, the model can relate the relative hardness parameter to several variables, including excavation rate, fragmentation results, and vibrations. It can also be used in the explosives loading process, similar to the model used by Dyno Nobel’s Differential Energy (DE) technology. In the relative hardness model for Caserones, a design is loaded in the drill system, and data is collected during the advance of the blasthole. The collected data includes rpm, torque, pressure, etc. Then, an algorithm using the measured variables while drilling and known relationships between the properties of the rock and the drill's performance is used to classify the average relative hardness of the blasthole in four intervals: hard, medium, soft, and very soft. Optimization techniques and models used in the oil and gas industries to analyze drilling performance were adapted to implement the algorithm. The model uses the concept of mechanical specific energy (MSE). Using the data from the drill, the algorithm identifies the depth where the MSE reaches a minimum to calculate the “relative hardness” for the blasthole under analysis. The results are presented in maps highlighting the areas where hard, medium, soft or very soft rock masses are expected. That information can be used to anticipate areas where explosives with higher energy need to be used or to predict areas of the blast with additional digging difficulties and then lower loading rates. The paper shows examples where “relative hardness” maps are compared to drilling speed excavation rates and other variables.

Jan 21, 2025

By Catherine Johnson, Barbara Rutter

The shock tunnel located at the Missouri University of Science and Technology Experimental Mine is 65 feet 9 inches (20.0406 m) in length. The tests performed inside of this tunnel are either arena tests or shock interaction and transfer (SIT) tests. Arena tests simulate a large open air blast, with lower explosive weights, by elongating the impulse of the blast wave. SIT tests are conducted to determine how the produced shock wave interacts and transfers its energy into a target object located at the end of the tunnel. The target used in this research is multilayered, with each layer being a different material. The targets are 2 ft. by 4 ft. (0.6096m by 1.2192m) pieces of Medium Density Fiberboard (MDF), DOW polystyrene foam insulation, and gypsum drywall. The order of these materials varies with each test. This shock tunnel is unique, because the geometry changes along its length. To fully understand how the shock waves are affected by these changes, a working model was needed. The second purpose of this model is to confirm the maximum charge size of 400 grams (14.11 oz.) of C4 that can be detonated inside the tunnel without causing damage to or failure of the tunnel, thus reducing the amount of time needed in downtime and repair. The model predicts pressures in various locations both within the tunnel and the attached target, thus assisting in determining where failures would likely occur. In the process of generating this model, several problems were encountered, including filling the tunnel with air, meshing the complex geometry, and creating the tunnel in a CAD system. This paper will discuss how these problems were solved. A working model was created by using ANSYS Explicit Dynamics and ANSYS Autodyn. The tunnel geometry file was created using SolidWorks and includes the complex geometry changes along with the target and its mount located at the end of the tunnel. The results produced by the model were compared to the field SIT tests. The comparison of the results from both the model and the experimental testing showed a similar trend in the pressure traces.

Jan 1, 2018

By Rajesh Sonkar, Sanjeev Kumar

The deployment of Dragline machines in opencast coal projects involves huge capital expenditure as well as operating costs. The mine operators always endeavor to ensure smooth excavation of material by the Dragline machines while meeting the major objectives of safety, minimal disturbance to environment and optimal operating costs. Optimization of fragmentation through well designed blasts is fundamental in meeting part of the objectives is good fragmentation of rock or mineral proposed to be lifted by the Dragline machine. If the overburden lying over mineral is not properly fragmented, it may result in formation of ‘Toe’ the removal of which is the most arduous task in opencast coal mines. The mine operators always endeavor to achieve best possible results in blasting to ensure smooth operation of the high cost Dragline Machine. However, despite continuous efforts by the blasting engineers involved in bench blasting for the machine, the formation of ‘Toe’ is an ever nagging problem faced in large opencast coal projects eventually reducing the overall operational efficiency of mining.

Jan 1, 2011

By Kinross Paracatu, Victor Morais, Luis Marinho, Rolando Fuentes, Lucas Steffen, Leopoldo Muñoz, Washington Vilas

Nowadays, mining operations close to communities face increasingly challenges, especially in their drilling and blasting operations. One of the critical effects are the ground vibrations produced in its surroundings. The impact on the community must be minimized to guarantee the license to operate and, on the other hand, costs must be optimized, and an adequate fragmentation must be achieved to ensure the efficiency of subsequent processes and, consequently, to give sustainability to the business. In this regard, it is necessary that some controlled blasting technique to be performed and the utilization of advanced vibrations models. Currently, it is common in the industry either use of the double decking technique, where very low explosive charges are applied, making it necessary to use smaller drill patterns in order to keep powder factor as per design, which strongly increases the demand for drilling and a consequent impact negative on costs.

Feb 6, 2023

By Radhe Krishna, Mutale William Chanda, Timothy Mwale

Blasting as a process is the emplacement of industrial explosives into blast holes suitably located to a free surface and detonated. Every blast hole containing a certain amount of explosive charge undergoes impulsive loading when detonated and results in the dynamic transfer of a powerful shock wave to the surrounding rock. It is the shock wave that brings about rock breakage when the tensile stress produced upon reflecting from the change in material density or free face overcomes that of rock material tensile strength. However, this shock wave comes along with unwanted destructive consequences such as damage to remaining rock, ground vibration, noise and fly rock. The above mentioned consequences pose a great threat to the Community of Wusakile, Kitwe as Mopani Copper Mines Plc wishes to increase its production by expanding the pit towards the community that lies within 150 m (164 yd) from the pit rim. As a requirement from the Zambia Environmental Management Agency (ZEMA), all blasting operations close to the community must maintain at least below the maximum vibration threshold of 10 mm/s (0.3937 in/s) PPV-Peak Particle Velocity or else risk closure of the mine (AMC,2009). In order to satisfy the above statement, a good understanding of explosives is required. This paper therefore presents the phenomenology of rock breakage by explosives with much emphasis on electronic blasting and how best this process can be controlled in densely populated communities. Factors affecting maximum projection distance such as, size of the fragment, shape of the fragment, angle of projection, the state of confinement of an explosive charge, were also studied. In addition, design faults, deviation in implementation and unforeseen geological conditions were also considered. The paper discusses the above facts based on research.

Jan 1, 2015

By Art Frye, Lee Pratt, Gaichang Zhao, Greg Newman

This paper will discuss the Wight Pit wall slash at the Mount Polley open-pit copper-gold mine that scavenged a high grade block of ore from two double-benches of the pit wall. The Wight Pit orebody, discovered in 2003, is located in the Northeast of the property with the southeast pit wall approximately 50m (165ft) from the edge of Polley Lake. In early 2009, the Wight Pit was nearing completion while an estimated 150,000 tonnes (165,000 tons) of ore averaging a grade of 1.4% copper remained just inside the southeast pit wall. The ore block started 24m (78ft) above the pit floor and extended up another 48m (157ft) with a 70o plane defining the back of the block.

Jan 1, 2011

By Cory Loukides, Cathy Aimone-Martin

Blaster training manuals used by the Office of Surface Mining (OSM) and others are outdated and cumbersome. A new approach has been developed using Microsoft PowerPoint with a Visual Basic overlay to produce modules on CD’s that present state of the art blasting techniques. The education modules contain enhanced information on topics such as explosives and initiation products, blast design, drilling, and vibration control. The content is based on safe practices and illustrated with numerous photographs and movies. Review questions, complete with explanations for incomplete answers, enhance the learning process and keep the blaster involved. The benefits of using an electronic format include the ability to continually change and update the training modules as new products, technology and applications become available. In addition, the blaster can work at home in preparation for class work and may reduce the time away from the job. This poster session presentation will allow potential users to view and take part in the evaluation of these modules.

Jan 1, 2004

By O. Cermak, F. Degonld

Although 3D fragmentation analysis is a relatively new technology, it is rapidly gaining popularity among mid-sized mining operations and quarries. The results provided by this technology are adequate, but like other picture analytic methods, it mainly focuses on the surface of the muck-pile. These results are incomplete or incorrect as falling rocks and boulders from the stemming zone are constantly influencing the muck-pile surface. This obstacle can be overcome by collecting a large amount of data and analyzing it over time. However, this is not always an ideal solution, as companies prefer to receive results immediately after the blast to make resource allocation decisions, production planning, and plan for the next blast. Over the past year and a half, we have conducted a study on various muck-pile fragmentation analysis results from 3D modeling in Central Europe, comparing the results between the surface and inside of the muck-pile. By analyzing multiple shot results, we were able to determine the percentage difference between the top and inside fragment sizes and calculate the range of correction coefficients for different rock types. Applying these coefficients to a single muck-pile surface fragmentation analysis allows us to determine the actual fragment sizes inside the muck-pile. This enables us to make informed decisions regarding loading, hauling, material mixing, and proper crushing or milling. By overcoming the limitation of surface-based analysis, we can now accurately evaluate blast performance, which leads to better processes optimization and increase efficiency. As 3D fragmentation analysis becomes more widespread, we expect to see even more benefits for the mining and quarrying industry

Jan 1, 2024

By Gerald R. Coonan

Early in the open session of the 1979 SEE Fifth Conference panel discussion, someone asked a question of the panel concerning the future intent of the Office of Surface Mining and the regulatory limits established for ground vibration and air blast. The "gist" of the question was: "What assurances do we have that OSM will not promulgate a limit of 0.5 inch per second ground vibration, or some other number within the next two years or so."

Jan 1, 1979

By G G. Paine, C V. B Cunningham, G Harries

The companies of the ICI Explosives Group have successfully used a wide variety of internal computer codes including BOBCAT, KUZ-RAM, ICRAX, XPLODE, BLEND, 3CRACK, MICBLAST, DETON, etc. In recent years the extensive experiences across ICI have been combined into a single compatible model engineered to worldwide technical service and customer needs for the prediction and assessment of blast results.

Jan 1, 1987

By Kai Nielsen

Drilling and blasting design results in a fragmentation that will have an important economic influence on all subsequent operations such as loading, transport secondary blasting and primary crushing.

Jan 1, 1987

By Kristen R. Bingham

"Today, more than ever, drilling and blasting contractors are challenged to manage the ever-changing risks associated with blasting operations. New neighborhoods are encroaching upon mine sites and blasting projects are confronted with increasing scrutiny by permit issuing authorities and nearby residents disgruntled by new construction. The act of transporting explosives material to and from thejobsite is far from easy and trouble-free. At the same time, the pressure to stay in compliance with the growing number of government regulations continues to mount. While new tools and technology are appearing in the workplace to address some of these challenges, losses still occur. Can the datagenerated by this technology help drilling and blasting contractors make better decisions? While basic risk management principles are still applicable, do new tools and technology assist in the effort to prevent losses? What are the downsides? In this age of new technology, is face-to-face interaction still necessary? While technology is certainly a useful component in the drilling and blasting world, can it be helpful in defending claims?"

Jan 1, 2017

By Thomas E. Ricketts

An important part of underground mine planning and operations involves the reclamation of working areas after blasting before the mining cycle can continue. This is especially true for mining that must use large blasting operations in the vicinity of extensive underground workings. In an effort to develop a rational procedure for estimating mine damage produced by blasting, underground rock fall has been assessed for a large-scale blasting operation in oil shale. The amount of mine damage has been quantified in terms of manshifts of effort required to reclaim underground working areas after blasting. This has been further broken down into the three main phases of reclamation, i.e., scaling and excavation, rockbolting, and miscellaneous repairs on ventilation, utilities, etc. Different types of openings have also been assessed including level tunnels, incline drifts and rooms. The effect of repeated blasting on mine damage has also been documented with initial blasts producing more damage than subsequent blasts.

Jan 1, 1988

By John Cory, Ran Tamir

Blasting data analytics are being increasing used to increase mining productivity, reduce mining costs, maximize high margin aggregate products, and to reduce fines. Three examples will be illustrated using simple models to maximize the percentage of blasted rock within established dimensions and reduce fines-one from video fragmentation distribution information, the second from sieved crusher fragmentation data, and the third from plant production data. In addition, the use of sieved crusher results to determine blasting related fines and the use of mine productivity data to maximize aggregate sizes when pattern (burden and spacing) areas are changed will be illustrated

Jan 1, 2012

By Jason Rock, Rob Thompson, Lee Julian

This paper presents an innovative shift in inhibited bulk products with specific reference to their manufacture and application.

Feb 1, 2020

By Jacqueline Berendzen

Summer internships are a great way for students to explore different career paths in the industry and get first hand experiences with potential employers. As a junior in mining and explosive engineering, my 2009 summer internship gave me a behind the scenes view of the actual workings of an explosive company and the role they play in the mining industry.

Jan 1, 2010