Search Documents

By C. S. Spirakis, A. V. Heyl

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The modified basinal brines, containing partly oxidised sulphur species, scavenged metals from basement rocks and sediments and transported them through the host rock, which contained local concentrations of organic matter. Reacting in various ways with the mineralising solution as temperatures at the sites of mineralisation changed, organic matter caused the precipitation and dissolution of a variety of minerals in the ore zones; it was organic matter that caused all of these reactions to occur at the same sites. Thus all components of the mineralising fluid - salt, water, heat, sulphur and metals - were obtained within the ore district. The siting of the mineral districts was related to the locations of faults through U- and Th-enriched granites beneath sediments containing basinal brines, and the locations of ore deposits within the districts were controlled by local concentrations of organic matter

Apr 1, 1995

By S. G. Ozkan

An investigation was carried out into the effect of physical parameters, such as particle size of the sample, residence time, solid/liquid ratio and impeller speed in the flotation cell, on the solubility in soft tap-water of colemanite (calcium-bearing borate) from Emet, in Turkey. Solubility increased steadily with residence time from 5 to 20 min but only minimally thereafter. There was a similar increase with impeller speed from 500 to 1 500 rev/min, beyond which a solubility of around 1.05 g/l was again established. There was a slight decline in solubility as the solid/liquid ratio was increased from 1 to 30%, with stable values around 1.05 g/l at a 20% ratio, while a sharp decrease was observed with decrease in size down to the -20 micrometre fraction. The effect of solubility should be taken into account if the application of a wet-processing method is being considered for the ore, while it can also result in losses of material during handling and storage

Jun 21, 1905

By S. A. Sayed, M. N. M. Ahmed, M. A. Doheim

The performance of a 12.7 cm hydrocyclone was investigated by considering the effect of design variables (diameters of the vortex finder and apex) and operating variables (pressure drop and solids content of the feed) at a medium feed solids concentration of mixed minerals. Cut-size was found to be the most important parameter in hydrocyclone design and operation. The effect of feed pressure in reducing hydrocyclone cut-size is less pronounced at medium feed solids concentration with a mixed mineral feed. The choice of vortex finder diameter and apex diameter becomes more sensitive at medium feed solids concentrations. The effect of feed solids concentration in increasing the cut-size becomes less marked at higher concentrations. Predictions of an empirical model were found to be in good agreement with experimental data. Comparison of results obtained from the model with those predicted by theoretically derived models showed the latter to be more promising, with the turbulent two-phase model giving closer agreement with the experimental data

Apr 1, 1995

By A. H. G. Mitchell

Most, if not all, of the six recognised post-Cretaceous, predominantly andesitic mineralised belts in the region are now thought to be subduction-related magmatic arcs. The Inner Carpathian arc and the Eastern Bosnia or Drina-Rhodope arc host numerous vein and replacement deposits with epithermal features and Zn-Pb+/-Ag as the predominant economic minerals. In contrast, the south Apuseni Mountains have produced over 1 600 t Au from epithermal veins but very little Zn-Pb. Recent age determinations and geophysical data from the Baia Mare district of the Inner Carpathians suggest that mineralisation succeeded volcanism by 1-2 m.y. and accompanied crustal extension and the cooling of a large, mushroom-shaped pluton whose boundaries define the mineral district. In the south Apuseni district, mineralisation can be explained by mixing of meteoric with low-salinity metamorphic water expelled during intrusion of mafic rocks into the middle or lower crust. The more continental or cratonic crust in the Drina-Rhodope and Inner Carpathian arcs precluded the input of low-salinity, Au-bearing metamorphic water; the Zn-Pb deposits formed where convecting meteoric water mixed with saline water, possibly introduced through carbonate rocks in the basement

Aug 1, 1996

By D. R. Wardrop, G. Walton

Paper presented at the UK minerals industry conference held in Leeds, UK, 3-5 April 1995. A description is given of the approach that has been taken to the design of the 550 000 000 t superquarry with a planned life of 60 years that is proposed for development. The quarry has been designed to replicate a corrie and a sea loch and will include excavated slopes more than 570 m high. The main geological and physical controls on the layout and the choice of development method are outlined. The operation phasing is presented and the geotechnical constraints on slope design and the feasibility of alternative quarry limits are discussed. Environmental considerations have been dominant in planning and the quarry has been specifically designed for closure

Jul 1, 1996

By M. M. Cole

An assessment of the combined application of remotely sensed satellite imagery, geobotany and biogeochemistry reveals the complementary value of these techniques in the Thalanga area. The SPOT imagery yields useful information on features of the terrain and discriminates the gossan over the ore zone. Geobotany differentiates geological units and the anomalous vegetation provides visual expression of the surface presence of the ore zone, while biogeochemistry effectively locates its concealed extension below Tertiary sediments and ferricrete

Jan 1, 1991

The Aredor mine employs conventional dragline methods to exploit alluvial diamond deposits. Production began in 1984 with the policy of mining in the terrraces during the wet season and in the river flats during the dry season. Early production failed to meet predicted grades. A major geological programme to re-evaluate existing reserves was undertaken. This resulted in considerable increases in reserves in the river flats. Many of the reserve blocks included flats on both banks of the Baoule river. Methods of access into the river flats, normally flooded in the wet season, were developed to allow mining throughout the year. River diversions have been the main method used to provide access into the reserve blocks and, most importantly, to remove the risk of flooding. Aredor has carried out six main river diversions with a total length of 12 km. The diversions allowed production planning to be made on the basis of the economic evaluation of the reserve blocks, without undue regard to natural ground conditions or to seasonal factors. The Manning equation was used for the calculation of channel dimensions and gave satisfactory results. The practical aspects of the diversion preparations and flooding prevention are described

Sep 1, 1991

By G. D. Schena, M Zanin

A numerical approach is presented for predicting the liberation of phases during comminution, with direct calculation of a liberation spectrum giving the fraction of the particulate system in each narrow size-composition class. The numerical model uses a Poisson flat process for stochastic generation of the non-convex three-dimensional Poisson polyhedral textures and the system of fractures that give rise to convex fragments. With this numerical approach, there is no need to assume random uniform isotopic fracture (lack of selective liberation); only computational geometry primitives are exploited for the derivation. The agreement with relationships obtained previously under the random uniform isotopic fracture hypothesis demonstrates that the approach is capable of deriving full liberation spectra directly. Both volumetric and superficial composition can be calculated

Jun 21, 1905

By A. M. Tunstall, N. Djordjevic, H. A. Villalobos

The damage zone behind a typical smooth-wall blast in the open pit was assessed by visually examining diamond drill core to identify blast-induced cracking, mapping core rock quality designations to identify changes in fracture frequency and conducting uphole seismic testing to determine changes in rock mass characteristics. The results from the three techniques show reasonable correlation. They suggest that major damage, in the form of fracturing of intact rock, occurs at least 7 m behind the smooth-wall blast and significant damage, in the form of opening and extension of calcite-filled fractures, at least 12 m from the blast. At greater distances the dominant damage mechanism is the loosening of existent joints within the rock mass. In the trachytes at El Soldado these damage mechanisms correspond to peak particle velocities of 2 000, 900 and 500 mm/s respectively

Jun 19, 1905

By P. E. J. Pitfield, S. D. G. Campbell

The regional structure of shear and deformation zones in the belt, which is recognisable in plan view on Landsat TM images, is interpreted in terms of a conjugate-shear model. Gold mineralisation is related to this framework at a variety of scales. The principal recurrent structural geometries hosting deposits at mines such as Motapa, Durban, Charliesona, Cecil, Sunace, Turk group, Queens district, How, Peter Pat, Matabele Sheba, Goodenough, Old Nic and Bushtick are associated with shear zones and folds and include conjugate systems (shears, shear intersections, kink sets), side-step systems (en echelon segmentation, duplexes, monoclinal inflections, antiform-synform couplets) and interactions of the two. Linear sections of shear zones are generally poorly mineralised. The same geometries are identifiable on all scales from local to regional, so sections of regional structural lineaments or areas within mines should be prioritised for further investigation or development on the basis of the gold-bearing geometries observed to be dominant locally

Apr 1, 1996

By P. Mousset-Jones, G. Danko

Variations of the temperature and steam/moisture content of the air with distance and time are modelled for a single airway. The input for the simulation is an air temperature that varies with time, together with the moisture/steam content that results, for example, from a fire with a given distribution of heat and of fume concentrations at the beginning of the airway. The transport of heat and moisture to the surface of the wallrock is assumed to be simultaneous. Such multiphase convection may result in evaporation from the moist wall close to the fire and recondensation downstream. The modelling of this non-linear effect is a unique feature of the new simulation. A new analytical solution is used to calculate the conduction of transient heat within the rock mantle, which, in the event of a fire, is typically a short-term process. This allows for an arbitrary variation of surface temperature with time - unlike that permitted by the age function solution, which is limited to stepped temperature changes. An iterative numerical scheme that has recently been developed to simulate mine climate is used to calculate the coupled transient heat conduction and multiphase surface heat transport in successive length increments along the airway. To demonstrate the simulation procedure a numerical example is presented in which a fire with a given distribution of heat and fume concentrations with time is located at the beginning of an airway

May 1, 1991

By R. A. Ixer, R. A. Lord, H. M. Prichard, A. J. Boyce, P. McConville, C. T. Pillinger, I. P. Wright, J. Maynard

Analysis of 62 samples show that the sulphides throughout the igneous stratigraphy have a magmatic signature, with the exception of the uppermost gabbros and the lowermost basal thrust talc-carbonate lithologies. Mean delta-34S values for whole-rock samples from harzburgites, dunite pods in harzburgite, crustal dunites and wehrlites, the main and high-level pyroxenites and gabbros suggest that the primary sulphides derived their sulphur from a magmatic source enriched in 34S. This finding is compatible with the proposed origin of the ophiolite above a subduction zone. Values for pyrite mineralisation in the uppermost part of the gabbros are thought to result from precipitation from a seawater-derived fluid, while isotopically light sulphur in the basal thrust could have been introduced from underlying metasediments. The replacement of pentlandite by heazlewoodite has not led to sulphur fractionation

Jun 19, 1905

During a programme to determine the suitability of the UK site for deep disposal of radioactive wastes, geostatistical methods were used to characterise rock heterogeneity on the basis of seismic and wireline acoustic-impedance data. The data were analysed to yield semi-variogram models that quantified the three-dimensional spatial heterogeneity of acoustic impedance. These models were reconciled with geological interpretations of the area and used to generate simulations of acoustic impedance, with wireline acoustic impedance as conditioning data. The three-dimensional simulated images were compared with actual seismic acoustic impedance. The variography confirmed a vertical zoning effect in the Borrowdale Volcanics, showing that it is caused by preferential clusters of high acoustic impedance values corresponding to regions of relatively low porosity. The method provided realistic three-dimensional models from sparse, one-dimensional wireline data

Jun 19, 1905

By J. K. Whyatt, W. P. Blake, T. J. Williams

A study at the Idaho mine revealed that, despite the apparent randomness of seismic events, common characteristics defined five recurring types. These characteristics included the geological structure that slipped, the first-motion pattern and the location and intensity of damage. Many large events caused little or no damage, and where it did occur it was concentrated at intersections between slipping structures and mine openings. Of 39 events between 1989 and 1994 with local magnitudes of 2.5 or more, 10 were caused by slip on bedding planes in the southern limb of the mine, 6 occurred near the vein along a set of near-vertical faults that form the central shear zone, 8 were strike-slip events on the Southern Control Fault, 4 were by slip on the vein itself and 10 involved strike-slip and/or dip-slip movement along the North Control Fault. Strategies for control of mining-induced seismicity need to consider all five types of event, lest a strategy to reduce one type increases others

Jun 19, 1905

By K. Nielsen, J. Kristiansen

A series of laboratory blasting and grinding tests on three types of hard and competent rock (coarse-grained monzonite, fine-grained granite and very fine-grained gabbro) showed that a higher level of applied explosive energy enhanced grindability and produced a larger amount of fine (-0.106 mm) material. This confirmed reported industrial experience and the results of previous investigations. However, the results did not provide any information on the quantitative relationship between the energy applied in primary blasting and that required in subsequent comminution. Only about 1% of energy consumed in conventional grinding is used to create new surfaces, while power efficencies in cone crushers have been estimated at 70-80%. In blasting, up to 20% of explosive energy may be transmitted to the surrounding rock as elastic strain energy, leading to both primary rock breakage and the generation of microcracks

Dec 1, 1995

By T. Yalcin

In the Box-Wilson method, the correlation between dependent and independent variables is represented by a polynomial response function, whose constant and coefficients are determined by applying regression analysis to the experimental data collected. The five levels used for each variable consist of a minimum, a maximum and three intermediate values. A study was carried out using Ni-Cu ore from Sudbury, Ontario, in which 15 experiments designed according to the Box-Wilson method were carried out in random order and in duplicate. The two sets of replicate data showed close similarity, with an overall variance of 0.311 for the five parameters studied. The response functions were used to optimise frother dosage, collector concentration and air flow rate and an experiment was then carried out under the optimised conditions; the results agreed closely with those predicted by the response functions

Jun 21, 1905

By Xiao Min You, D. R. Swonbourne

Smelting of Cu anode slimes involves the use of a slag to hold the oxidised Cu, but some Ag is also inevitably oxidised to the slag. The solubility of Ag in sodium silicate slags at 1 100 and 1 150 degrees C has now been determined over a very wide range of oxygen partial pressures. Silver was found to be present in the slags both as neutral atoms and as AgO(0.5). The activity coefficient for atomic Ag was a very strong function of slag composition and temperature, whereas that for AgO(0.5) was much less affected by slag composition and was almost independent of temperature over the limited range examined. The results reveal that the dissolved Ag cannot be fully recovered by reduction of the slag with very reducing gases

Jun 21, 1905

By A. Ersoy, M. D. Waller

The principal factors which require consideration in predicting drilling rates are the bit-type, the bit operating parameters and the characteristics of the penetrated rock. A single index is not a sufficient basis for predicting performance. A variety of rock types were drilled in the laboratory with polycrystalline diamond compact (PDC) and impregnated diamond core bits using a fully instrumented drilling rig at different rotational speeds and with a range of weights on the bit. Quantitative determinations of a wide range of textural, mechanical and intact rock properties were also made. Multi-variable linear regression analysis was then used to develop predictive models of rates of penetration from the operating and rock property data. The models have been verified by statistical tests. The analysis indicated that the models for the pin and hybrid PDC bits have potential for practical application. However, although the model for the impregnated diamond bit appears to be reasonable from a purely statistical point of view, it may not be satisfactory for drilling uses as it is based on two measures of rock hardness alone. The application of multiple regression analysis to PDC drilling performance is novel and the technique shows promise for the prediction of rock drillability with PDC bits. The ability of the technique to provide a mathematical characterisation of the performance of new drill bits in specific rocks may prove to be of value to drill manufacturers and users

Aug 1, 1995

By G. G. Barbante

Anode slimes produced during copper electrorefining are a valuable source of silver, gold, selenium and tellurium. The conventional pyrometallurgical process for treating slimes involves preliminary leaching in sulphuric acid followed by smelting in a reverberatory furnace with fluxes, but it is slow and has many recycle streams. The chemistry of the phases and the reactions that occur in slimes smelting are poorly understood and and this prevents major improvements to the process. Laboratory-scale experiments were conducted using unleached slimes, with and without the addition of fluxes and under neutral, oxidising and reducing conditions. Results show that selenium is readily removed as gaseous selenium dioxide and that molten Cu-Ag-Se-O phases form when fluxes are added. Oxidation-refining of these phases by air injection and flux addition can result in the formation of silver suitable for further electrorefining

Aug 1, 1995

By A. L. Grabovski

The potential of eccentric cone crushers for fine crushing has been improved by increasing the swing frequency of the moving cone, balancing the crusher, ensuring uniform feed via a rotating funnel with sideways discharge, introducing hyperbolic motion and employing the inertia crushing method, but further improvements to the specifications of existing cone crusher designs are limited by the rigidity of their kinematic coupling. A new design has been developed which combines two crushing modes, stone on liner and stone on stone, each with its own advantages. The main aims are to produce finer materials and to reduce liner weight. The benefits include an increase of more than 10% in the output of fine particles, improved protection of the liner against wear, as a result of filling of the cavities by material being crushed, and the use of almost 20% less material in casting of the liner. The chamber can be used in place of the usual liners of fine cone crushers

Jun 21, 1905