Search Documents

By H. Wotruba, L. Gronen, A. Hellmann, S. Sindern, J. Katzmarzyk

"This paper focuses on the beneficiation of the REE-Y-Nb-Zr complex ore from the ‘Khalzan Buregtei’ deposit, Mongolia. Pre-concentration based on mineralogical studies was investigated at the Unit of Mineral Processing (AMR) and the Institute of Applied Mineralogy and Economic Geology of RWTH Aachen University. In order to minimize the energy consumption in the most energy intensive grinding process a pre-concentration process using dry magnetic separation of particle sizes coarser than required for the liberation of the valuable ore minerals was designed. Dry magnetic separation in the particle size range of 63-250 µm is suitable as the pre-concentration method, due to the intergrowth of REE-Y-Nb-Zr bearing minerals with magnetic minerals determined by QEMSCAN© analysis. The results showed that a mass reduction of 45.3 wt.-% at high recoveries of REE, Y, Nb and Zr (90 wt.-% and higher) in the pre-concentration product was achieved at the beginning of the process chain. The improvement of process efficiency as shown in this study depends on the abundance and association of minerals affecting the magnetic properties (e.g. hematite) of the ores. Therefore, these mineralogical parameters are as important as grain size and ore grade for the geometallurgical evaluation of potential mining operations at ‘Khalzan Buregtei’.INTRODUCTION Polymetallic deposits containing other critical elements besides REE have the advantage of being robust to economic development and fluctuations of individual metal prices. (Gronen et al., 2016). These deposits can host economic grades of heavy and light REE, Y, Nb, Ta, Zr in complex mineralogical compositions. About 120 deposits of this type are known worldwide, including ‘Norra Kärr’ in Sweden, ‘Strange Lake’ in Canada and ‘Khalzan Buregtei’ in Mongolia which are not valued economically yet. (Salvi. & Williams-Jones, 2004.)"

Jan 1, 2018

By Jan J. Cilliers, Nicolas Barbian, Esther Ventura-Medina

"Froth structure and stability are known to play an important role in determining flotation recovery and selectivity. An industrial sampling campaign was performed to develop a clearer understanding of the effect of flotation variables on froth stability and the role played by the resulting stability on flotation performance.Froth stability was estimated as the fraction of bubbles bursting on the surface of the froth through image analysis and the solids loading on the bubbles at the top surface. It was generally found that high air flowrates resulted in a drop of froth stability showed by a drop in the fraction of air overflowing and a decrease in the solids loading and simultaneously produced low copper recoveries and low concentrate grades. Deep froths only allowed a small fraction of air to overflow and consequently produced low recoveries. An increase from a standard to high frother dosage did not result in a larger fraction of air overflowing, hence producing low recoveries. Likewise, low frother addition only allows low recoveries because the resulting unstable froth cannot support itself. Low aeration was found to be preferential as it allowed high particle loading, therefore high bubble stabilisation, and low gangue entrainment, resulting in the highest flotation performance.Additional laboratory tests were performed to introduce a new stability parameter and to give a clearer understanding of the effect of flotation variables on froth stability. The results confirmed some of the observations made on the plant."

Jan 1, 2003

By Axel Pankewitz, Andrew Smith, Mathias Stender, Christian Behrens

"Particle size measurement is one of the most important factors in obtaining peak performance of the mineral processing plant in order to ensure efficient milling and flotation circuit operation. Off-line particle distribution analysis technologies only allow an infrequent check of the ore slurry size and hence do not allow for timely process monitoring or intervention. Most existing on-line particle size analysers suffer from a variety of disabilities such as poor statistics, non-representative sampling or mechanically complex setup. This paper will describe an Ultrasonic Extinction based method which overcomes many limitations of existing online analysers and has proven its performance for mineral applications over many years. Installation examples will be given. Since new technologies usually raise e questions about comparability and agreement to common particle size analytical methods e.g. sieving or laser diffraction analysis, extensive studies were performed comparing these different technologies to quantify the quality of results as well as its mathematical robustness."

Jan 1, 2014

By Volker Vogt, Wolfgang Sand, Eberhard Gock

"It was discovered that the selective activity of bacteria during the extraction of raw material concentrates by means of flotation could also be achieved with extracellular polymeric substances (EPS) excreted by bacteria. EPS, which is extracted by means of centrifuging bacterial cultures, can help to significantly reduce the use of cyanides, approximately 200,000 t/a of which are used for ore dressing today.The bacterium used was Acidithiobacillus ferrooxidans. In order to identify the bandwidth of the oxidation activity, 20 bacterial strains of the strain collection of the University of Hamburg were attracted to iron(II) sulfate and pyrite under defined conditions. All strains oxidized iron(II) sulfate ten times faster than pyrite.EPS has so far been derived from four strains. In general, EPS extracts are divided into a hydrophilic and a hydrophobic fraction. The hydrophilic fraction is composed of e.g. fucose, rhamnose and glucose; fatty acids such as dodecanoic acid, hexadecanoic acid, octadecanoic acid and nonadecanoic acid were found in the hydrophobic fraction.Pure mineral phases and mineral mixtures were used for the flotation tests. As opposed to current knowledge, the results were reproducible with technical flotation machines."

Jan 1, 2003

By P. N. Mohan Das, K. Harikrishna Bhat

"The major ilmenite reserves are located in India at Chavara (CH), Manavalakurichi ( MK) and Chatrapur, Orissa (OR). India stands first in terms of ilmenite reserves, which are estimated to be 278 million tonnes out of which, 142 million tonnes are processable. Mineralo-chemical analysis shows that Chavara ilmenite is the most weathered one with about 60% TiO2 while Chatrapur is the least weathered with about 50% TiO2. Co-existence of ilmenite with pseudorutile, rutile and haematite is observed in substantially varying amounts in the three deposits. It is observed that the tropical weathering rather than the source rock difference has apparently played an important role in imparting major compositional and structural dissimilarities among ilmenites in different places.In processing of ilmenite through the Becher process, aeration rusting of pre-reduced ilmenite is found to be the rate limiting step thus, affecting the productivity of the process. Investigations have proved that the addition of some organic compounds such as glyoxal, sucrose etc., to the system accelerates the reaction to such an extent that the rusting time has been reduced to less than half.A new route of processing ilmenite for synthetic rutile has also been developed in which, ilmenite is carbothermally reduced and then processed through plasma route. The slag thus obtained is processed further to get high-grade synthetic rutile, metallic iron and high purity iron oxide. The process has been scaled up in a continuous moving bed plasma reactor. It is technologically and economically more viable where, all the iron values are recovered as salable byproducts. This paper describes the salient features of the technologies developed for the beneficiation of ilmenite to synthetic rutile."

Jan 1, 2003

By K. Yoo

Cuprous oxide is one of the oldest antifouling agents and also acts as red pigment in these paints. In printed circuit board manufacturing industries, waste etchant contains a substantial amount of copper ion. In the present study, a process was suggested for recovering cuprous oxides from the waste etchant and optimum conditions were investigated to recover the cuprous oxides. The process consists of two steps: in first step, Cu powder is added into wastewater solution, and cupric ions re-duce into cuprous ions (Cu+Cu2+?2Cu+), where cuprous ions precipitate as cuprous chloride; In second step, cuprous oxide is synthesized by adding NaOH into cuprous chloride solution (2CuCl+2NaOH?Cu2O+NaCl+H2O). Optimum conditions were investigated to recover cuprous oxide in the processes. When copper powder was added into wastewater with copper ions, Cu concentration decreased from 15.6% to 2.6% and ORP decreased from 620 mV to -59.9 mV. This result shows that cupric ions reduced into cuprous ions. XRD data indicated that the precipitate was cuprous chloride powder. Using the cuprous chloride recovered and NaOH solution, cuprous oxide was synthesized. To investigate the optimum condition, various NaOH solutions were added into water with CuCl, and then pH, ORP, Cu concentration, Cu contents in precipitates were analysed. XRD data showed that main component of precipitates was cuprous oxide.

Jan 1, 2014

By Georg Unland, Thomas Wegner

"Different types of impact crushers use the physical effect of impact to crush rocks. The rocks can vary from soft to hard and from ductile to brittle but they should never be abrasive. Since the principles of impact crushing of larger rocks are hardly investigated these crushers are still sized rather by empirical than by scientific approaches.In order to investigate the principles of comminution by impact of large rocks a test rotor was developed and rocks of different dimensions were tested. The integrated measuring devices of the rotor enable the recording of impact forces and of absorbed impact energy with high resolution during the contact time.Since impact crushers stress the rock particles with a defined velocity the main crushing properties are gained as a function of the applied velocity and the particle size of the rock: likelihood of breakage, contact time, maximum crushing force, mass specific crushing work, surface related crushing ratio and crushed fragment shape distribution."

Jan 1, 2003

By C. Carrasco

"Over the last 30 years the average grade of mined ore bodies has significantly decreased while the proportion of waste removal has in many cases more than doubled. This has been identified as prime reason of a major increase in energy consumption and decrease in productivity across mining operation. Metal coarse preconcentration of ROM feed grades by size rejects low grade gangue/waste material in the size range of 10-100 mm prior to grinding, typically before primary crushing. This relies on propensity of metal to preferentially deport in the fine size fractions after breakage. Metal preconcentration by size has the potential to increase energy efficiency and therefore improve mining productivity on unit of metal basis. Results of an extensive belt cut sampling campaign conducted at a major Australian Au-Cu mine operation show that for some samples between 90% of Au and 80% of Cu is in 40% of the mass at -50 mm fraction. This indicates that low grade coarse material can be removed from the circuit, doubling feed grade at half of the tonnage and therefore improve energy efficiency per unit metal produced. This response, however presents significant variability in the same order as other processing attributes such as impact hardness and flotation recovery. This has led to development of geometallurgical laboratory tests using blast hole chips and drill core facilitating mapping and population of coarse metal preconcentration signatures in long term resources and short term production models. Preferential Cu deportment by size at drilling scale can be recognised, however scales up factors are required to transform laboratory results to production responses. At 50 % of mass the drilling products underestimate the belt cut responses by 20-30 %. Bulk sampling campaign with blast hole and drill core samples spatially related was also conducted to investigate in more detail the difference between production scale and drilling scale preconcentration responses."

Jan 1, 2014

Incomplete liberation of mineral particles is one of the key factors limiting the performance of industrial flotation circuits. This work aims to quantify the relationship between different breakage modes and how these affect mineral liberation properties. A copper porphyry (bornite) ore sample was subjected to breakage using a piston-die compression unit and an impact mill. The particles produced as a result of each mode of breakage were then characterised using Mineral Liberation Analysis (MLA) to quantify the mineralogical and liberation properties of the progeny particles. The impact mill was found to produce bornite that was finer grained relative to the host particles. In con-trast, bornite discharged from the piston-die unit closely followed the size distribution of the host particles and was retained to a greater extent in the larger/intermediate size fractions. The results provide insight into what breakage methods are optimal for the purposes of downstream separation.

Jan 1, 2014

By D. Steele, B. Ndlovu

"Adequate characterisation of clays is becoming increasingly important as operating mines move into areas of more complex ores. The processing therefore needs better mineralogical characterisation to identify problematic ores for better planning before issues arise. While a number of instrumental mineral characterisation methods are available, X-ray Diffraction (XRD) is widely recognised as perhaps the best technique for the identification and quantification of minerals, particularly clays. When an appropriate sequential and systematic sample preparation and treatment protocol is employed with instrumental XRD analysis individual clays can be uniquely identified, and the proportions of interstratified clays can also be quantified. The effect of sample preparation on the XRD analysis and identification of clays was investigated in this study. The results showed that sample preparation protocol is indeed critical to accurately analysis and characterisation of clays. For example, both dry grinding and micronizing affected the degree of crystallinity of kaolinite leading to the formation of reactive surfaces or changes in the physicochemical behavior. It was also found that the apparent degree of preferred orientation in platy minerals correlates directly with the amount of force/pressure applied during the preparation of backfilled powder samples. This work showed that manual preparation can produce highly variable peak intensities especially with minerals that show any preferred orientation. KEYWORDS Clay; XRD; kaolinite INTRODUCTION Clays are important in our life and they have numerous applications in modern world from cosmetics to environmental remediation. Therefore, clays have been extensively investigated for many years. Adequate characterisation of clays is becoming increasingly important as the mineral processing industry faces more complex mineralogy with the need for better mineralogical characterisation to identify problematic ores and plan accordingly. In most studies, X-ray diffraction (XRD) method has shown the unique capability to characterise mineralogy, especially for the fine grained size materials. The XRD technique is particularly diagnostic for clays. It is known that under ideal conditions, the peak intensities of an XRD diffractogram are proportional to the concentrations of individual minerals present in the sample. Hence, the qualitative mineralogical data obtained from XRD can be quantified, using either the internal or external standard methods. However, it is also known that clays are particularly sensitive to the influences of sample preparation method due to their physical characteristics (e.g. fine grain size, morphology, relative physical softness, crystallinity, thermal sensitivity) that could be destroyed by inappropriate preparation prior to the analysis. Thermal and mechanical treatment and grinding of clays can change their crystalline structure, and consequently, their characterisation results by XRD analysis. The behaviour of clays in grinding has been widely studied, especially for kaolinite (Miller and Oulton, 1970, Milocevic et al., 1992, Tomasevic-Canovic et al., 1992). With prolonged grinding time, the crystallinity of the clays can decrease (Filipovic-Petrovic et al., 2002). It has been shown that grinding may gradually cause the loss of hydroxyl ions of kaolinite (Gonzalez Garcia et al., 1991)."

Jan 1, 2018

By S. J. Neethling

"This paper examines the impact of several key variables on the performance of flotation cells. The study makes use of a simulator for the froth phase of the flotation vessel, as the main purpose of this study is to separate the impact of different variables from one another. In experiments it is very difficult to separate the effect of variables from one another as a change in a singe input parameter, such as air rate, invariably also affects many of the other key variables, such as bubble size and bubble bursting rates.In order to achieve this a base case simulation that is typical of many of the rougher cells found in sulphide flotation circuits was carried out. Four key variables, air rate, incoming bubble size, surface bubble size and the fraction of the bubbles flowing out of the cell unburst, were varied in order to obtain the system.s response.The most significant results were obtained when the bubble size was varied. An increase in the incoming bubble size has the effect of reducing the pulp zone recovery, but increases the froth zone recovery. If it were possible to vary the incoming bubble size without influencing the overflowing bubble size, the impact of the change would be unclear because of these two competing effects. The effect of a change in the overflowing bubble size has an opposite effect on the froth recovery, with larger bubbles resulting in lower froth recoveries.A final interesting result is that all the effects examined affect the process to a similar degree, which implies that none of these variables can be disregarded, either in industry or in further research."

Jan 1, 2003

By I. Yochev, A. A. Metelev, A. I. Stepanenko, A. P. Purgin, M. G. Viduetsky, A. M. Panshin, I. F. Garifulin

"Pneumatic flotation cells of the KFM series are intended for the concentration of various ores and technogenic materials. The key operating principle of the flotation cells of the KFM series is the preparation of pulp for flotation in blowers, offering the advantage of an accelerated flotation process. This report summarizes the results of the implementation and operation of the KFM cells at Russian and foreign projects in 2015-2017. Their implementation and operation experience confirms the high efficiency of the KFM cells, especially in the head of lead and zinc, copper and zinc, copper flotation processes:head KFM-600 flotation cell recovers from lead-zinc ore (Rudmetal AD modular concentrator) up to 52% of lead in a single stage (without cleaner flotation) in a salable lead head concentrate (grade of up to 76% lead, 2.3% zinc). The flotation cell proved to be much more efficient than originally expected in the process description in the design phase,flotation of the copper-zinc ore from Novo-Shemur deposit (PJSC Svyatogor concentrator) in two KFM- 1400M cells recovers up to 65% of copper and 70% of zinc in a high-grade bulk copper-zinc concentrate containing 12-13% of copper and 25-28% of zinc. The installation of the two cells with a combined capacity of 26 m3 allowed to decommission 4 chambers of FPM-16 pneumomechanical flotation cells with a combined capacity of 64 m3 with a simultaneous increase in the overall ore concentration performancea single KFM-1400M cell (13 m3) recovers from the copper ore from Volkov deposit (PJSC Svyatogor concentrator) 53% of copper into a high-grade copper head concentrate (33.0% of copper). For comparison, the pneumomechanical cell FPM-16 (capacity 16 m3) has almost half as low copper recovery (29.6%) into the head concentrate at a lower grade (30.5% copper)."

Jan 1, 2018

By F. Y. Kang

There are rich resources of natural graphite in China. It would be a good opportunity to upgrade national graphite industry if natural graphite with modification is used in lithium ion battery. Micro-crystalline graphite in high purity was coated with a carbon film on the surface. The initial cycle efficiency was improved to be 89.9% and cycle stability was remarkably improved. The experiments proved that microcrystalline graphite with carbon coating have excellent electrochemical performances at low cost as anode materials for lithium-ion battery. In addition, H2SO4-GIC technique was used to prepare the natural flake graphite powders with mild-exfoliation. Sub-micro and nano pores were found in the graphite samples. In correspondence the reversible capacity, rate capacity and cycle life were improved, which would meet the demand of high-power lithium-ion battery. Natural graphite is the most promising anode material for large-scale lithium-ion batteries. The demand of modified graphite grows up greatly in the market. Microcrystalline graphite with surface coating and flake graphite with mild-exfoliation are the promising commercial anode materials for the industry of lithium ion battery.

Jan 1, 2014

By L. G. Wang

The stability of foams and froth plays an important role in flotation, in which small amounts of relatively weak non-ionic surfactants (frothers) are used to produce air bubbles and foams. In the present work, factors affecting the stability of the foams produced in the presence of common frothers, such as n-pentanol, n-octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG), have been studied. We used the thin film pressure balance (TFPB) technique of Schelud-ko-Exerowa type to measure the equilibrium film thicknesses. The results were used to determine the contributions from the various surface forces to the disjoining pressures in the thin lamellae (foam) films formed between air bubbles. In addition, we used a model developed by Wang and Yoon (Colloids and Surfaces A: Physicochem. Eng. Aspects, 2006) to calculate the elasticities of the lamellae films at the critical thicknesses at which films rupture. The surface forces and elasticity da-ta were then compared with the foam stabilities in the presence of the various flotation frothers. It was found that foam stabilities are controlled by both film elasticity and surface forces, the relative contributions of which change with frother type and concentration. In general, surface forces play a more important role at relatively low frother concentrations, while elasticity plays a more important role at higher concentrations. At the frother additions usually employed in the mining industry, MIBC relies on surface forces while PPG-400 relies on film elasticity in producing stable foams. The former is capable of dampening the hydrophobic force, which is a major attractive force destabilizing lamellae films, while the latter is capable of reducing surface tensions at low concentrations.

Jan 1, 2014

By Bruno Miotto, Rômulo Faria, Juliano Tessinari

Water has become a scarce resource in quality. Companies in the ornamental stones sector use water intensively in their processes. Given the current situation, it is imperative to rationalize this feature that at first is related to the reduction of consumption, through no waste. Considering the importance of environmental preservation of this resource and also to comply with the legislation that governs the procedure for processing of ornamental stones, new alternatives should be available for the maintenance of current activities and promoting the development / growth of the sector on the principles of environmental sustainability and economic in future scenarios. The ornamental stones processing industries, especially for micro and small enterprises, require the implementation of a management program that optimizes the use of this feature, since the techniques individually processed operate with three basic processes dependent on water use: split blocks, polishing and finishing slabs. This technology requires a large volume of water resources and control measures involving operating recirculation water can minimize power consumption, making the company more profitable and sustainable. This is a survey of literature, associated with technical reports provided by partner companies and government agencies. This study aimed to the organization and provision of theoretical knowledge about the subject matter coupled with management practices, which may be reproduced or re-purposed in ornamental stones processing companies. It should be noted that the industry in question is lacking in technical expertise for the implementation of sustainable attitudes relevant to water reuse.

Jan 1, 2014

By F. Boylu

In this study, Ca-bentonite was subjected to a series of systematic hydrocyclone tests with the aim of developing separation procedures and in turn achieving optimum recoveries. In hydrocyclone tests, vortex and apex diameters and also feed pressures were investigated. In each hydrocyclone set, vortex diameter was kept constant while the other two parameters varied to produce bentonites con-centrates of various smectite contents. The separation efficiencies were evaluated based on the cation exchange capacity (CEC), particle size and swelling index. The detailed hydrocyclone tests showed that, upgrading of Ca-bentonites require procedures different from the bentonites reported in the literature. Sodium and mixed bentonites are easy- to-disperse and easy-to-separate whereas calcium types need to be scrubbed rigorously for disintegration. Scrubbing properties of ca-bentonite were investigated as a function of scrubbing time and percent solids by weight (PS). The scrubbing conditions at 700 rpm for 1.5 hours and percent solids of 30 % were found more effective for achieving a better quality bentonite. In addition to the parameters mentioned above, the effect of percent solids on hydrocyclone separation was also studied. Although Ca-bentonites permit studying at higher percent solids, increasing solids content of the pulp deteriorated the quality of the clean products. Application of an appropriate separation scheme enabled the development of a unique separation procedure involving stage wise scrubbing followed by hydrocycloning which yielded calcium bentonite concentrates with CEC of 90 meq/100 g and high swelling indexes of 12 mL from the original bentonite of 65 meq/100 g and 7.0 mL, respectively. These results indicate that upgraded bentonite products can be conveniently used in various diverse industrial applications including bleaching earth, desiccant, cat litter, paper etc.

Jan 1, 2014

By Y. C. Liu

Arsenic bearing copper-gold ores deposit have been found in most areas of China, especially in southwest. Due to the very closed association between arsenic, copper and gold, conventional flotation and cyanide leaching process may not give positive results. An arsenic bearing copper-gold ore in Sichuan province ,with gold grade of 10.12 g/t, 0.6% Cu and 0.14% As, is characterized by superfine grains with -40 microns fraction accounting for 70.9% and the gold enwrapped mainly by pyrite and tennanite accounts for 34.31%. Arsenic in this ore occurs in isomorphism, deposited in tetrahedrite. The ore was processed primarily in two stage flotation to get copper bearing gold concentrate and pyrite bearing gold concentrate respectively, and sequentially processed by leaching. Under the pressure of 300 KPa and 110~115 ?, the copper-gold concentrate was leached by an oxidizing and catalyzing leach agent then copper and gold were separated from each other in leach solution. The pyrite bearing gold concentrate was processed by cyanide leaching with the leach residue as sulfur product. The test results showed that copper recovery was up to 88.89%, gold recovery up to 89.18% and sulfur recovery up to 92.64%.

Jan 1, 2014

By John O. Marsden

"Technology development and innovation has played a crucial role in the copper industry throughout history. The effective development and implementation of new technologies allows mankind to produce copper at progressively lower cost of production at a given feed grade and mineral type. This progress serves to counteract cost inflation/escalation over time and, depending on the magnitude of the cost benefit, allows ore cut off grades to be reduced thereby improving the availability, accessibility and utilization of resources. Two broad categories of technology development and innovation play a key role in this process: (i) incremental improvements and optimization of existing technology provide benefits in the near- to medium-term, and (ii) step change technologies provide value over the longer term. A key issue for potential developers and implementers of new step change technology is how to justify resource allocation and expenditures for such initiatives. This paper examines this issue with reference to specific case studies in the copper industry. INTRODUCTION AND BACKGROUND Technology development and innovation has played a crucial role in the commodity minerals industry throughout history, and none more important than the copper industry. As new, cost-efficient technologies are commercialized, the cost of production in real terms at a given ore feed grade and mineral type decreases. This progress enables ore cut off grades to be reduced allowing lower grade material to be processed economically, which in turn increases the availability and supply of the metal or mineral of interest. Cost inflation/escalation works in the opposite direction, squeezing margins for operations utilizing incumbent technology to process material from a given ore deposit. A prior review by the author considered the issue of technology development and sustainable competitive advantage. This review concluded that first movers and fast followers can achieve competitive advantage for periods of 10-15 years through effective deployment of new technologies (Marsden, 2004). A new, more comprehensive study and evaluation was completed in 2014. This paper presents a portion of the results from the 2014 study."

Jan 1, 2018

By Carlos Rabanal, Levi Guzmán

"The concern regarding grinding media consumption rates is as old as the invention of the tumbling mill. Over the years many materials and grinding media shapes have been tested. Through all this, steel grinding balls have proved to be the most effective media for comminution in tumbling mills. There have been several approaches to be able to the wear of the ball charge in any given mill, all of them based on limited empirical evidence. The mining industry still utilizes the Bond Abrasion test that was developed in the 1960´s. As shown later in this publication, this approach shows error greater than 60%. More recently, in 2007, Radziszewski from Mc Gill University has proposed a different total grinding media wear model; this model is based on decoupling the effects of the abrasion, corrosion and impact wear mechanisms. Also in 2007, Benavente, at the time with Moly-Cop Peru, presented an empirical model relating both ore properties and operational conditions that would affect the wear performance of the grinding media. For the database referred in this article, Benavente’s model shows an average error of ± 12% which represents a higher degree of improvement in comparison with previous approaches. The current paper presents recent research conducted by Moly-Cop Peru to further improve the capability of the empirical model originally developed by Benavente to estimate grinding media wear rates. The work performed included extensive determinations of the Bond Abrasion Index for different types of ores, collected at industrial grinding applications where the corresponding operational information was made available. The results of the research enabled us to build a more robust and confident model for estimating the grinding media wear rate. The average error of this new model is in the order of ± 9% which is a significant improvement over the models previously described."

Jan 1, 2014

By Komar Kawatra, Joseph Halt

"Bentonite clay has been the traditional binder for iron ore pellets. However, bentonite increases pellets’ silica contents and is expensive. Researchers have proposed lowering bentonite doses by mixing it with other common binders. These mixtures may only be successful if the fundamental bonding mechanisms are understood. For example, what happens when bentonite (physical bonding) is mixed with fly-ash (chemical bonding)? What happens when bentonite is mixed with cornstarch (physical bonding)? In this paper, experiments are described where bentonite was mixed with various ratios of cornstarch and fly-ash, and pellets were agglomerated using 0.66 % w/w binder. Ca(OH)2 and CaCl2 were added as activator and accelerator, respectively, to the bentonite-fly ash mixture. Curves of pellet dry strength vs. bentonite-starch ratio were linear, suggesting the physical-physical bonding mechanisms were compatible - acceptable strengths (> 22 N) were produced at all bentonite-to-starch ratios. This was contrary to bentonite-fly ash mixtures, which displayed dry strength curves with a noticeable minimum due to competing binding mechanisms. Bentonite alone and fly ash alone produced acceptable strengths (> 22 N), but their mixtures resulted in weak pellets. Due to the positive results using cornstarch (CS) binders, the effects of CS solubility in water were investigated using two CS with high and low solubility (60 and 7.5 %). CS was premixed with bentonite at various ratios (0, 20, 40, 60, 80, 100 %). Pellets were agglomerated using 0.66 % w/w binder. The dry strength of pellets ranged from 50-300 N using the high solubility CS mixtures, and from 50-85 N using the low solubility CS mixtures. Fired strengths exceeded 2200 N/pellet at all bentonite-cornstarch ratios. This research showed that cornstarch solubility is an important factor in determining its effectiveness as a binder for iron ore concentrates, but significant work is still necessary before it can be used as a bentonite replacement."

Jan 1, 2014