Search Documents

By Jean Wehbe, Daniel C. Brahana

"This paper presents a case history of drilled pier construction for a new stadium in Atlanta, Georgia. The stadium structure is supported on several different foundation types, with the heaviest ""mega columns"" typically bearing on drilled pier supported mats. The project includes 141 drilled piers with design diameters of 5.5, 6 and 6.5 feet. The piers bear on bedrock at depths of 20 to 110 feet below the ground surface. Many of the piers included rock sockets with design lengths of 5 to 18 feet. A pre-production drilled pier load test program was completed including one Statnamic load test, two Osterberg Cell tests and two lateral load tests. Non-destructive testing (crosshole sonic logging and sonic integrity testing) were also performed during construction. Production pier installation with over 3800 linear feet of earth excavation and over 1350 linear feet of rock excavation was completed in a little over four months. The piers were installed using both the cased hole method and the slurry method. All cased holed required downhole inspection and slurry holes were initially inspected with a mini-SID device and subsequently by sounding. Advanced drilling equipment and tooling were used to meet the production requirements for the project. This paper reviews the highly variable soil and rock conditions encountered at the site, briefly presents the results of the load tests, and discusses pier installation procedures and the equipment used for installation. The paper also presents conclusions related to the installation and lessons learned.INTRODUCTIONWith the opening of AT&T Stadium in Dallas, a new era of stadium construction began in the U.S. The new age stadiums are larger and have more amenities than their predecessors. The new Atlanta Falcons stadium is no exception. Many of the new features, including Atlanta’s innovative retractable roof, result in extraordinary structural loads. The roof structure is supported by a series of mega columns that bear on eight large caps, six of which are drilled pier supported. Each of the pier caps contains between 8 and 16 drilled piers that bear in the underlying bedrock. The design pier diameters are 6 and 6.5 feet. Augercast piles were used to support two of the mega column caps. Drilled piers, augercast piles, aggregate piers and spread footings are used to support the more lightly loaded portions of the structure."

Jan 1, 2017

By Satyajit A. Vaidya

This paper presents a case-study in the design and construction of deep foundation element supported mats for two residential towers on an18,000-square-foot site in Brooklyn, New York. Based on site sub-surface conditions, conventional mat foundations bearing on medium dense sand, having an allowable bearing capacity of 3 tsf, were originally anticipated for the 16 and 25-story towers. However, when the tower shear walls were relocated to the edges of the mat foundations due to architectural revisions, the significantly increased mat edge contact stresses applied to the soil subgrade resulted in calculated settlements of a magnitude that would adversely impact the proposed structures and the neighboring/bordering lot-line building and rail transit subway structures. To address this issue, deep foundation element supported mats were designed for the towers. The design was performed as an iterative process involving structural SAFE and geotechnical Plaxis finite element computer analysis to develop a coordinated geo-structural model of the foundation system. Initial presumptive design values of 45 pci and 445 kips/inch were used for the modulus of subgrade reaction and minimum deep foundation element stiffness, respectively. The designed foundation system consisted of 40 and 60-inch-thick mat foundations for the 16 and 25 story towers, respectively. Initially, the deep foundation elements were designed as 50-foot-long, 14-inch-diameter elements installed to sustain a maximum individual compressive load of 250 tons. The final deep foundation element design was subsequently refined to consist of a 48-foot-long, drilled and grouted IBO Titan 103/51 element designed to sustain a maximum load of 167 tons. Subsequent field load tests on the deep foundation elements confirmed element stiffness ranging from 1,040 to 1,530 kips/inch, with measured mobilized side shear of about 29 psi. The mat foundation reinforcement was adjusted for the pile stiffness values determined in the field load tests, and the deep foundation supported mats were constructed. The two towers were subsequently constructed, and have performed successfully.

Jan 1, 2010

By Jeremy Butkovich

Dynamic soil-structure interaction (DSSI) analyses are becoming more common in bridge designs, especially in seismically active areas. Because of its proximity to two active fault zones, the Evergreen Point west approach bridge replacement will be base isolated, and will be designed using DSSI. The project team completed two independent bridge designs to satisfy peer review requirements. The designs required substantial characterization of the soil dynamic behavior using both laboratory and in-situ testing. The analyses made use of earthquake time histories spectrally matched to conditional mean spectra. This led to reduced, and more realistic seismic demands on the structure, compared to conventional uniform hazard spectrum matching. The bridge analyses suggest that the preliminary bridge design is relatively conservative. This will allow the design team to potentially reduce shaft/column diameters and reinforcement. The design team estimates that the dynamic analysis design could represent a net savings of around $60 to $90 million compared to a conventional design.

By Jean Wehbe, Daniel C. Brahana

"The new Mercedes-Benz Stadium (MBS), home of the Atlanta Falcons, is part of a new era of stadium construction in the U.S. These new-age stadiums are larger and have more amenities than their predecessors. Many of the MBS’s features, including its innovative retractable roof, result in extraordinary structural loads. The roof structure is supported by a series of mega columns that bear on eight large caps, six of which are supported by drilled piers. Each of the pier caps contains between 8 and 16 drilled piers that bear in the underlying bedrock. The design pier diameters are 6 and 6.5 ft (1.8 m and 1.9 m). Augercast piles were used to support two of the mega column caps. Drilled piers, augercast piles, aggregate piers and spread footings were used to support the more lightly loaded portions of the structure.The focus of this article is the construction aspects of the drilled pier foundations. Initially, a fairly extensive drilled pier load test program was performed. Load testing included a Statnamic compression test, two Osterberg Cell tests and two lateral tests. Production pier installation included over 3,800 linear ft (1,158.2 m) of earth excavation and over 1,350 linear ft (411.4 m) of hard rock excavation. The piers contain more than 6,600 cu yd (4,587.3 cu m) of concrete and 1,100 tons (998 tonnes) of reinforcing steel. Drilled pier installation took about 4.5 months. ABE Enterprises was the specialty foundation subcontractor and Bauer-Pileco was the equipment provider.Site and Subsurface ConditionsThe project site is in downtown Atlanta and was originally occupied by residential buildings. A portion of the site was later developed as a rail yard, and other areas contained light manufacturing, warehouses and other relatively light structures. For the past 15 to 20 years the site had been used for surface parking.Beneath a surficial layer of manmade fill, soil test borings at the site generally encountered residual soil, partially weathered rock and the parent bedrock. The bedrock at the site is highly variable, both in elevation and in hardness/quality. The depth to rock is reasonably uniform within the western two-thirds of the site at about 20 to 50 ft (6 to 15.2 m), with a few exceptions. In the eastern third of the site, the rock drops off dramatically to the north and east. In one mega column cap, there was almost 80 ft (24.3 m) in elevation difference. In two borings in the cap that were 20 ft (6.1 m) apart, the top of rock varied in elevation by 34 ft (10.3 m)"

Jan 1, 2016

By M. Hesham El Naggar, Mehdi Heidari

"Equivalent fixed-base cantilever model is a common approach for performance base seismic design of bridge structures supported by extended pile-shaft. In this method, global displacement ductility factor is related to local curvature ductility demand by assuming a concentrated plastic hinge at location of maximum bending moment. Equivalent plastic hinge length is one of the key parameters that should be assumed accurately in kinematic expression of the cantilever model. Although, some expressions have proposed to estimate the length of the in-ground plastic hinge; however, these relations yield differing results. In this paper, a general expression is derived based on the concept of distributed plasticity to predict the plastic region of yielded piles in clay and sand. A length modification factor is defined to relate the equivalent length of plastic hinge to the real plastic zone. Then, results from nonlinear pushover analyses are used to propose an equation for the modification factor as a function of displacement ductility factor.IntroductionDuring severe earthquake events, development of the plastic hinge in pile foundation below ground level is inevitable for bridge structures supported on extended pile-shafts. A common approach for seismic design of the yielding pile-shafts is to replace the pile-soil system by an equivalent fixed-base cantilever assuming the equivalent system has the same global response as that of the pile-shaft (Budek et al. 2000; Chai 2002). In this method, plastic curvature is concentrated at the center of the equivalent plastic hinge below ground surface. Prior knowledge of plastic-hinge length is essential for proper assessment of assess plastic displacement at the top of the pile-shaft. Unfortunately, existing recommendations for estimating plastichinge length are largely incomplete and/or inadequate.During the last two decades, several relationships have proposed for evaluating the equivalent plastic hinge length, Lp, based on experimental and numerical studies. Budek et al. (2000) conducted numerical modeling to calculate the plastic-hinge length of piles embedded in cohesionless soil. They found that the plastichinge length varies linearly with both soil stiffness and aboveground height, e. Chai and Hutchinson (2002) conducted full-scale experimental tests on reinforced concrete piles in sand. They reported that Lp depends primarily on the aboveground height of the pile, neither sensitive to the soil stiffness nor to the value of displacement ductility factor. They stated that the equivalent plastic hinge length is relatively independent of the displacement ductility factor and is not very sensitive to the change in soil density. On the contrary, Goel (2014) and Liu et al. (2016) conducted nonlinear numerical analyses which revealed that Lp changes with the displacement ductility factor and even suggested that using different values of Lp for different seismic design levels is essential for a reliable estimation of the ductility capacity."

Jan 1, 2017

By Chang-Yu Ou, Shao-Chi Chien, Hsuan-Hsiang Chang

"A field test was performed to investigate the applicability of electroosmosis with the injection of saline solution of Taipei silty clay. The calcium chloride solution and sodium silicate solution were used as the saline solution for the injection in this test. The results of this study indicate that injection using calcium chloride solution and sodium silicate solution during the electroosmosis to increase drained water from cathode and electro-chemical reaction can greatly improve the effect of electroosmosis and shorten the time of treatment. The results of field vane tests showed that the undrained shear strength after treatment increased an average of approximately 120% for a treatment period of 24 days.INTRODUCTIONThe first field application of electroosmosis in soil was demonstrated by Casagrande in 1939. Since then, more complete field applications of electroosmosis such as Bjerrum (1967), Fetzer (1967), and Lo et al. (1991b) have been made.The results of field electroosmotic work for a period of 120 days were presented by Bjerrum et al. ( 1967). The mean undrained shear strength, Su, increased from 18 to about 40 kPa, with a uniform surface settlement of about 0.5 m. Lo et al. (1991b), with a more sophisticated installation and a relatively larger spacing, also had positive results. For a 3 m electrode spacing during the treatment of a period of 33 days, the mean Su increased from 18 to about 25 kPa. Although the effect of the electroosmosis could be applied in the field based on the above examples, the response remained slow. For actual field work, the application of electroosmosis will be limited due to short project schedules and request of the effect of improvement."

Jan 1, 2005

By Mohammad Ali Rowshanzamir, Mehdi Aghayarzadeh

"This article is an effort to improve our understanding of the performance of geogrid retaining structures (GRS) through numerical analyses. The numerical modeling utilized a commercially available finite difference program, FLAC3D. In this context an extensive parametric study has been carried out on two different GRS walls (vertical reinforced block and inclined reinforced block) to investigate the influence of internal design factors such as soil strength properties and reinforcement stiffness on the performance of these walls. The main purposes of the parametric study were to (1) investigate the sensitivity of the modeling results to the input material properties, (2) examine the influence of the internal design factors on the performance of GRS retaining structures, and (3) improve the internal design of GRS walls on the basis of the working stress information obtained from the parametric study. Based on the analyses results, it was revealed that GRS walls with oblique reinforcement and reinforced block (rotated against natural backfill) have much better performance in terms of reduction in the stresses and strains of reinforcing elements as well as decrease in the wall lateral and vertical displacements in comparison with vertical reinforced block (conventional wall). For example, with 12° inclination of the wall reinforced block there was 50% reduction in the backfill settlement. Also increasing the reinforcement stiffness amount from 10MPa to 50MPa decreases the wall face displacement more than 50% in both GRS walls.INTRODUCTIONOver the past few decades, Geosynthetic- Reinforced Soil (GRS), a soil mass reinforced by geosynthetic layers to restrain the soil lateral deformations, has been employed in the construction of many types of earth structures, including retaining walls, embankments, slopes and bridge abutments. In fact GRS structures are typically more flexible (hence more tolerant to differential settlement), more adaptable to low quality backfill, easier to construct, require less over-excavation, and more economical. Nevertheless, there is a need for an accurate design tool that can predict the performance of GRS structures under working stress conditions and can predict their failure loads as well.Many studies have been published on the performance of the soil reinforced walls such as Isabel et al., 1996; Bathurst et al., 2000; Kazimierowicz-Frankowska, 2005; Nernheim and Bathurst, 2008; Chen and Chiu, 2008 Correia et al., 2012; Erlich et al. 2012. Several numerical studies have also been made throgh finite elements and finite difference techniques on reinforced soil retaining walls to analyze the wall deformations (e.g. Hatami et al. 2001& 2006, Liu and Won 2009, and Abdelouhab et al. 2011). A limited laboratory research has been reported indicating of improving effect of tilting face on GRW performance (Chen and Chiu, 2008). However no major numerical study was found on the effects of face or reinforcement tilting."

Jan 1, 2017

By Qingwei Joshua Ong

Tension piles, also known as uplift or anchor piles, are necessary to resist uplift forces that might cause structural distress. In excavation projects, most uplift forces are developed because of hydrostatic pressures, and so tension piles are subjected to a great deal of tensile forces. Most current methods of design for tension piles completely neglect the tensile strength contribution of concrete, relying only on the steel members to carry the tensile stresses, resulting in an overly conservative design. The stressstrain behavior of the composite material of concrete and steel must be considered for a realistic simulation of tension piles. This paper will examine a case on a tension bored pile in typical soft clay to demonstrate the importance of considering the tension strength and tension softening of the concrete.

Nov 1, 2022

By Don C. Warrington

This paper describes a new wave equation analysis program called ZWAVE, which is a program specifically for external combustion hammers. The program is de-scribed in detail, the discussion dealing with topics concerning the program such as 1) the numerical method the program uses to integrate the wave equation, which is different from most other wave equation programs; 2) the modelling process of both cushioned and cushionless hammers; 3) the automated generation of mass and spring values for both hammer and pile; 4) the method of dealing with plastic cushions; 5) the use of a recently developed model for computing shaft resistance during driving; 6) the computation and generation of values based on basic soil properties such as shear modulus, Poisson's Ratio and soil density; 7) the completely interactive method of feeding data to the program; 8) the method used to compute the anticipated rebound and the energy used to plastically deform the soil; and 9) the format of the inter-active input of the program and the program's output. Sample problems for the program, along with comparison of the program results with data gathered in the field, are presented.

Jan 1, 1988

By Anthony T. C. Goh, Zhiye Zhao, Laddu B. Jayasinghe, Hongyuan Zhou, Yilin Gui

"Ground vibrations from blasting are undesirable and they are very short in duration with high principal frequencies and high amplitude. Structural response to that kind of excitations may differ significantly from that generated by lower-frequency earthquake vibrations. In practice, the damage to nearby structures to generated ground vibrations has been controlled by various codes and regulations available. However, the existing vibrations limits are not always applicable, as they depend on the geological conditions of the site and the dynamic characteristics of the structure. This paper investigated the influence of the rock-soil interface on the response of pile foundation to ground-borne vibration from rock blasting, through numerical simulations using finite element software LS-DYNA. It is found that the slope of the rock-soil interface greatly influences the location of damage and the extent of damage on the pile. The bottom of the pile is subjected to a larger blast pressure and stresses are highly concentrated at the pile bottom. Thus, the pile bottom can fail in shear before it reaches its plastic moment capacity.INTRODUCTIONDrilling and blasting is the widely accepted method to large-scale rock breaking activities in civil engineering constructions due to its cost effectiveness, higher efficiency and ability to break hard rock. However, ground vibrations from blasting are undesirable and it can cause damage to nearby structures. In practice, the damage to nearby structures to generated ground vibrations has been controlled by various codes and regulations available. The existing vibration limits are not always applicable, as they depend on the geological conditions of the site and dynamic characteristics of the structure.Pile foundations are commonly used as foundations of high-rise buildings and bridges to transfer the heavy loads from the superstructure above through weak compressible soil strata into deeper, competent soil layers which have adequate capacity to carry these loads. In engineering practice, many piles are normally designed to carry mainly vertical loads and very little lateral loads, as typically the vertical loads (the gravity) are significantly larger than the horizontal loads such as wind loading. However, in recent years, there have been a number of reported case studies of translational soil movements that have induced stresses and bending moments that have damaged pile foundations and in some cases resulted in collapse of the superstructure. Typical lateral load include nearby construction activities such as an excavation for a basement or slope, the construction of a road embankment or a tunnel, as well as earthquakes (Abdoun 1997; Goh et al. 1997; 2003; Chen et al. 1999; Dobry et al. 2003; Boulanger et al. 2007; Black et al. 2007)."

Jan 1, 1900

By Shawna Munn, Carol Dounitch, Erika Acton

The EQ Bank Tower, a 24-storey office tower with 4 levels of underground parking, is currently under construction at 25 Ontario Street in the downtown core of Toronto, Canada. The tower geometry required an 18 m (60 ft) deep excavation inside an existing 3-storey 100-year-old façade, to be retained in place throughout construction. This presented a variety of design challenges that required several innovations and a customized monitoring program. In this paper, we will discuss two major challenges, and highlight the innovative and adaptable solutions carried out using performance-based design leveraging the observational method. The first was installation of a shoring system in a 500 mm (20 in) gap between the historical façade and a live gas main. The second involved excavating 10 m (33 ft) into expansive shale bedrock adjacent to a sensitive neighbouring building.

Oct 1, 2022

By Paul Doherty

It is known that the axial capacity of a displacement piles installed in clay varies with time. Consolidation theory suggests that dissipation of porewater pressure set-up during pile installation would lead to increased effective stress and hence higher pile resistance. In recent years a number of case histories have reported time dependent capacity increases for piles installed in sand. Although there is some debate regarding the physical mechanisms controlling this phenomenon, known as ageing, it is unrelated to pore pressure dissipation as piles in sand are installed in primarily drained conditions. A series of field tests designed to investigate ageing effects in soft clay are presented in this paper. Full-scale load tests on 6m long 250 mm square concrete piles, which were driven into soft clay are described. The piles were first tested approximately 100 days after installation, at which stage full equalization of the excess pore pressures had occurred. Static load tests were then performed up to 10 years after pile installation. The piles exhibited significant ageing, with their shaft resistance increasing by up to 66% over a 10 year period. Possible mechanisms for such aging characteristics are explored.

Jan 1, 2011

By Peter Yen

This session consists of five papers. Three involved research on the properties of grout materials, specifically ultrafine cements and polyurethane grouts. Two papers present the development of soil grouting technology and monitoring methods. Of great interest are the papers on ultrafine grout penetrability testing focusing on the pressure filtration effects encountered in permeation grouting applications (Ericksson, Stille and Mittag, Savidis). The comparison testing of hydrophilic and hydrophobic polyurethane grouts submitted by Vrignaud, Ballivy, Perret and Fernagu assessed the long-term performance of these materials for repairing saturated cracks in concrete, subject to thermal expansion and contraction. Two very practical papers present the development of soil grouting, where permeation, fracture, replacement, jetting and other grouting techniques are utilized. The papers by Lees with Chuaqui and Warner present experience with ultrafine and other commonly used grout materials. Methods to measure and monitor the injection process and verify production progress are discussed.

Feb 10, 2003

By Orestis Zarzouras, Amalia Giannakou, Jacob Chacko

"When designing structures in seismically active areas, foundations of critical structures are typically located away from known faults. Indeed many seismic codes prohibit construction in the immediate vicinity of seismically active faults establishing minimum setbacks from the faults. However, for long structures such as bridges, tunnels and pipelines, a fault maybe unavoidable, and fault rupture risk impossible to preclude. This paper presents a case study of a bridge foundation design that incorporates the consequences of fault deformations passing through the foundation. A series of site surveys were conducted to characterize the fault environment, and fault displacement hazard analyses were conducted to develop design displacement demands. Subsequently, numerical analyses were performed to evaluate the fault rupture-induced demands on a pier foundation in terms of displacements and rotations. Initially, analyses were performed that model the free field fault rupture propagation to the ground surface of the fault to ensure that the basic site characteristics are captured. Subsequently, the foundation elements were introduced in the model and the fault rupture is simulated again. The interaction and influence of the foundation on the fault rupture propagation is calculated, and the consequent demands and distortions of the foundation block provide a basis for structural engineers to design the bridge.IntroductionThe Izmit Bay bridge, a 3-km-long suspension bridge that crosses Izmit Bay in Turkey, is planned to be constructed in one of the most seismically active places in the world. The south approach structures for the Izmit Bay Bridge along the western side of the Hersek peninsula bring the bridge down from on the order of El. 60 meters at the South Anchorage to an elevated embankment approximately 1.3 km farther south (Figure 1). The south approach structures are located within a zone of secondary deformation around the primary trace of the North Anatolian Fault. The concept design team has developed a concept design for a “viaduct” structure that consists of 10 spans with lengths varying between 136 m and 100 m and two back spans one of 125 m, attached to the main bridge and the other of 74 m attached to the south embankment."

Jan 1, 2017

By Herbert F. ?Buck? Darling

A bridge replacement project in Rochester, NY, encountered difficulties when it was determined that rock below one pier was sloping downward toward the river at an angle of 42 degrees versus anticipated 12 degrees. Cofferdam design and construction became very difficult. The unanticipated subsurface conditions delayed the project by eighteen months and increased the cofferdam cost by almost $3.0 million ($US) when direct costs and associated delays were taken into account. The initial approach after discovery of the problem was to use the same type pier design and modify the cofferdam accordingly. This resulted in a cofferdam 12 meters (39.4 feet) deep on the shore side and 18 meters (59.0 feet) deep on the water side. The design used a master pile system to attain required wall strength and used rock anchors to prevent the cofferdam from moving toward the river. The pier foundation was then redesigned by the owner using revised seismic parameters. The original stepped footing carved into rock was replaced by caissons socketed into the rock beneath a large tremie concrete placement. The revised pier and cofferdam designs caused a shift from a mostly land based cofferdam, excavation, and rock removal project into an almost entirely water based cofferdam, caisson drilling, and tremie construction project. These design changes resulted in a reliable, safe, and unusual cofferdam and construction method. All of this was accomplished within a very narrow worksite with a railroad on one side, and the river with its public and commercial freighter traffic on the other. In addition, the existing two-leaf drawbridge was to be maintained in place which put further limitations on the water borne equipment. The engineering and construction considerations, problems, and solutions related to these cofferdams and pier foundations are presented.

Jan 1, 2013

By Antonio Kodsy, Lutful Khan

A research was carried out to test the possibility of reducing the pullout resistance of metal sheet piles driven in clay soils using Electrokinetic (EK) conditioning. The hypothesis was applying an electric gradient for a certain period of time should reduce the adhesion between the clay soil and the sheet piles. Tests were conducted on bench scale thin stainless-steel metal plates embedded in pure kaolinite clay, and mixtures of kaolinite clay and sand. The pullout resistances were determined after 20, 40, and 60 minutes residence times of steel plates in the soils before and after EK conditioning under an electric gradient of 1500 V/m. In kaolinite clay, the pullout resistance showed linear reduction with the duration of EK conditioning and about 60 % reduction in pullout resistance was observed after 60 minutes EK conditioning. For the kaolinite-sand mixtures, the pullout resistances were reduced by about 70% and 80% for 20% and 30% sand contents respectively after 20 minutes EK conditioning and showed no significant improvement with the increase in conditioning duration. It was concluded that the proposed electrokinetic conditioning process could potentially reduce the pullout resistance of metal plates embedded in clay and clayey soils. SHEET PILE WALLS Sheet pile walls are typically used at waterfronts as retaining structures or during the construction phase to shore the soil and avoid collapse of the excavations. When used as permanent structures, sheet pile walls are not removed after the completion of the project. However, as temporary support, they are extracted after the completion of the project and reused. In pure clay soils the extraction processes often becomes a challenge requiring very large pullout forces which could damage the sheet piles. There is a research need for developing an efficient method of sheet pile extraction from clay soils addressing the issue of pullout force reduction. However, very few researches have been conducted regarding the extraction techniques of sheet piles and their economic effect on the cost of a project. In this study a novel method for reducing the pullout resistance of sheet piles in clayey soils using electrokinetic conditioning was explored. The hypothesis of this research is that the electrokinetic process in soil/water system, specifically electrophoresis and electroosmosis, could be used to loosen the sheet pile walls embedded in cohesive soil and hence reduce the required force of extraction. The aim of this study was to test this hypothesis through laboratory tests carried out on steel plates embedded in cohesive soil samples. The pullout forces of the steel plates before and after varied duration of electrokinetic (EK) conditioning were evaluated and compared. The process was also investigated for clay-sand mixtures.

Jan 1, 2019

By Anthony T. C. Goh

"For deep excavations in soft clay, it is common to use jet grouting piles (JGP) prior to excavation to minimize wall deflections and ground settlement, and to prevent basal heave instability. In this paper, finite element analyses were carried out to assess the basal heave factor of safety for excavations in soft clay supported by JGP. Comparison of the factor of safety from the finite element analyses with limit equilibrium methods was then performed. Subsequently, to account for the uncertainties in the soil and JGP properties, a simplified reliability analysis procedure is proposed to estimate the probability of basal heave failure for deep excavations supported by JGP.INTRODUCTIONJet grout piles (JGP) are often used to prevent basal heave instability and to minimize excessive wall and ground movements associated with deep excavations in soft clay deposits (Shirlaw 2003; Wen 2005; Ou 2006). The jet grouting process which is carried out prior to any excavation works produces a series of short overlapping grout columns resulting in a “continuous” base slab (commonly termed as jet grout pile or JGP) below the final excavation level that spans across the entire excavation (Gaba 1990; Hsieh et al. 2003; Ho and Hu 2006). Typically, the JGP thickness ranges from 2 m to 4 m.The focus of this paper is on the assessment of basal heave instability for deep excavations in clay stabilized with JGP. Finite element analyses were first conducted to determine the basal heave factor of safety for deep excavations in clay with JGP. Comparisons were then carried out with factors of safety based on conventional limit equilibrium methods. Since the conventional factor of safety approach does not explicitly reflect the uncertainties of the soil and JGP properties, it is demonstrated in this paper that a simple reliability based approach (Hasofer and Lind 1974) can be used to assess the probability of basal heave failure.LIMIT EQUILIBRIUM METHODFor excavations is clay, the Terzaghi (1943), Bjerrum and Eide (1956) and Eide et al. (1972) methods which are based on bearing capacity theory, are commonly used to determine the basal heave factor of safety. Another commonly adopted method in Japan and Taiwan is the slip circle method which involves taking moments about the lowest strut level (JSA 1988; Hsieh et al. 2008; Luo et al. 2012). The slip circle method has also been applied for excavations with a JGP at the base by incorporating the undrained shear strength of the JGP. In the slip circle method, the basal heave factor of safety FSslip is assessed by taking moments about the lowest strut level (Fig. 1)"

Jan 1, 1900

By Amalia Giannakou

When designing structures in seismically active areas, foundations of critical structures are typically located away from known faults. Indeed many seismic codes prohibit construction in the immediate vicinity of seismically active faults establishing minimum setbacks from the faults. However, for long structures such as bridges, tunnels and pipelines, a fault maybe unavoidable, and fault rupture risk impossible to preclude. This paper presents a case study of a bridge foundation design that incorporates the consequences of fault deformations passing through the foundation. A series of site surveys were conducted to characterize the fault environment, and fault displacement hazard analyses were conducted to develop design displacement demands. Subsequently, numerical analyses were performed to evaluate the fault rupture-induced demands on a pier foundation in terms of displacements and rotations. Initially, analyses were performed that model the free field fault rupture propagation to the ground surface of the fault to ensure that the basic site characteristics are captured. Subsequently, the foundation elements were introduced in the model and the fault rupture is simulated again. The interaction and influence of the foundation on the fault rupture propagation is calculated, and the consequent demands and distortions of the foundation block provide a basis for structural engineers to design the bridge.

By Mitsuhiro Shibazki

I can't answer that question but I am looking at Andy, my co-author, and he says we didn't measure it. No movement. If I understand it correctly, how do we handle lateral forces in shear? The main columns were designed as pin connections so there wasn't a moment in the shear between the pile cap and the columns the steel reinforcing was used to resist that. I am not aware of how we would have installed those, it is possible to try and submerge them all if the jet grout is still fluid. They were higher than design. You are correct.

Feb 10, 2003

By Onur Guvener, Kalaiarasi Vembu, C. Vipulanandan

"Installation procedure and the quality of the material used in the construction have significant effects on the behavior of the Auger Cast in Place (ACIP) piles. In this study, Installation and curing of a 760 mm (30 in.) diameter and 12 m (39 ft) long ACIP pile with a design capacity of 1140 kN (128 tons) in hard clay was investigated. Construction quality was monitored using the automated monitoring system where the volume of grout pumped and the pressures were monitored with depth. The curing of the pile was monitored using axial vibrating wire strain gages at four levels and lateral vibrating wire strain gages at two levels. The residual strain and temperature profile in the curing pile was monitored over a period of week to determine the appropriate time for load testing the pile. Axial behavior of Auger Cast in Place (ACIP) Piles in hard clay was studied using full scale load test on an instrumented pile. The load-settlement and load transfer relationships of the pile was investigated based on the load test results. Development of skin friction in the load test pile and the reaction pile was also investigated.INTRODUCTIONAugered cast-in-place piles (ACIP) are drilled foundation installed by drilling a hole with a continuous flight auger to a predetermined depth. Non-displacement Augered Cast-in-Place (ACIP) piles are increasingly used for supporting building, bridges, sound barrier walls and many other structures around the world. In an ACIP pile, depending on the soil type and rate of the auger advance, ground stresses are maintained near the value that existed before construction by using a continuous flight auger, which is never withdrawn until the cementitious material (fluid Portland cement grout) is placed by pumping the grout beneath the withdrawing auger under pressure through the hollow stem of the auger (Vipulanandan, 2005). ACIP piles are typically installed with diameters ranging from 0.3 to 1.0 m and lengths up to 30 m (Brown, 2005) although longer lengths have occasionally been installed. Comparing to the drilled shafts and driven piles of equivalent size ACIP piles can be installed more rapidly with fewer disturbances to the surroundings in favorable geological conditions. Hence the installation procedure and the quality of material used in the construction have significant effects on the behavior of ACIP piles (Vipulanandan, et al. 2007). In this paper construction quality control technique for ACIP piles was investigated. Load displacement and load transfer behavior of pile in compression and tension in hard clay was also studied. The development of side resistance in compression and tension for the load test piles and the reaction pile were also investigated."

Jan 1, 2017