Search Documents

By Suthan Pooranampillai

This paper presents a case study of the use of single axis cement deep soil mixing (CDSM) to deal with static settlement and seismic stability of the foundation soils under a reinforced soil slope (RSS) embankment up to 50 feet high. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter-bedded with silty sand layers and organic silt where identified as being potentially liquefiable. CDSM was selected to address the embankment foundation concerns and allow for future trenchless installation of utility lines beneath the embankment. The presence of a confined, artesian aquifer within the design depth of the CDSM led to the installation of a depressurization system to avoid an upward gradient through the wet soil-cement. In addition to addressing the design approach, the paper discusses the challenges associated with quality assurance of CDSM within the time constraints of an ongoing project. The limited recovery rate of conventional triple tube coring in the soil-cement and double tube wet sampling led to the use of sonic coring to provide a near continuous core of the soil-cement.

By João Veludo, Eduardo Júlio, Helen D. Robinson, Jesús E. Gómez

"Utilization of micropiles for structural retrofit requires connection of the micropiles to the footings of the existing structure. Almost ten years ago, an experimental research effort was carried out in the US to investigate the magnitude and mechanism of development of the bond strength between micropiles and existing concrete. The study resulted in important conclusions on the mechanism of connection capacity development and provided specific recommendations for practical design of micropile-to-footing connections. In the last five years, the original study was complemented by an intensive experimental effort in Portugal aimed at answering many of the questions still remaining on this topic. This paper is a summary of the knowledge that is presently available on the capacity of micropile-to-existing footing connections. It presents the results and observations of model tests performed in the US and Portugal, as well as some tests from actual construction sites. The paper presents clear evidence that friction may be the most important component of connection capacity. It also presents a clear correlation between confinement and connection capacity.IntroductionUtilization of micropiles for structural retrofit requires connection of the micropiles to the footings of the existing structure. This is often accomplished by drilling through the footing and developing the connection by direct bond between the micropile grout and the existing concrete. Almost ten years ago, an experimental research effort was carried out in the US to investigate the magnitude and mechanism of development of the bond strength between micropiles and existing concrete. Smooth and textured micropile inserts of varying lengths were tested to failure inside pre-drilled holes of varying diameters. That investigation led to several publications (Gomez et al. 2005, Wilder et al. 2005, Cadden 2009) on the mechanism of development of bond strength between micropiles and concrete, which included a chart for preliminary bond value selection depending on the diameter of the hole and texture of the micropile.An intensive testing program was carried out in Portugal in the last five years. The program focused on answering questions posed by the original investigation and on finding the relationship between connection capacity and level of confinement. Both investigations, and especially the testing performed in Portugal, provided an invaluable amount of information on the mechanisms of failure of micropile-to-footing connections. This information should be the basis for development of design procedures that, until now, were not available."

Jan 1, 2015

By Clif Kettle

The paper will detail the design and execution of passive and active settlement control measures, the means adopted to overcome the various physical and operational constraints, and to meet specified allowable settlement criteria. The paper will highlight the close integration between the tunnelling and geotechnical contractors, designer, and Client, and demonstrate how particular practical difficulties were overcome by both the design and the construction methods.

Jan 1, 2008

By James M. Tantalla, Jr. Ellman

"Construction of the powerhouse for the Willow Island Hydroelectric Project, located at the Willow Island Lock and Dam, required a 120-ft deep temporary excavation inside the limits of a cellular cofferdam on the Ohio River side of the excavation and a soil-bentonite seepage cut-off wall on the landward side of the excavation. Stability analyses were performed for critical sections to evaluate the stability of the soil slopes and rock cuts using limit equilibrium, tension crack, and buckling analysis techniques. The stability analyses indicated adequate factors of safety through the landside embankment sections, and for the weighting berm soil slopes in front of the riverside cellular cofferdam. However, the results of deep-seated stability analyses through the rock supporting the riverside cellular cofferdam indicated marginal factors of safety for the 100-year flood condition. Consequently, the riverside portion of the excavation required enhanced stability measures, namely the installation of long, high-capacity rock anchors. Also, the dewatering system was modified to lower the site piezometric head to near the top of rock to improve the stability of the rock cuts.Thirty high-capacity rock anchors were installed on the upstream, riverside, and downstream sides of the cofferdam rock cut. The rock anchors consisted of multiple, seven-wire strands designed to provide the full-required design load at 60% of the strand capacity. Rock anchor loads varied from 1,968 to 2,074 kips. The maximum number of strands per anchor was 59. Bond lengths assumed an allowable bond stress of 100 psi based on the rock bond from pull-out tests.Project DescriptionAmerican Municipal Power, a nonprofit organization that owns and operates electric generation facilities for its member communities, has been in the process of constructing hydroelectric power plants adjacent to existing navigation locks and dams along the Ohio River. The Willow Island Hydroelectric Plant was recently completed on the West Virginia bank of the river adjacent to the US Army Corp of Engineers (USACE) Willow Island Lock and Dam. The plant is on the opposite river bank to the locks, and includes two turbine generating units with FERC rated capacity of 44MW at a 20-foot head differential. The Ruhlin Company of Sharon Center, Ohio was awarded contracts to construct both the cofferdam and the powerhouse. Construction began in mid-2011, and was completed in early 2016."

Jan 1, 2016

By A. David Miller, Douglas M. Barber

"The Rocky Mountain Arsenal was used by the military to produce chemical warfare agents and incendiary munitions for use during World War II and later by private companies for the production of industrial and agricultural chemicals. After an investigation performed in accordance with CERCLA confirmed significant levels of contamination due to the common industrial and waste disposal practices of the era and the discovery of over 300 species of wildlife inhabiting the land the Rocky Mountain Arsenal became a wildlife refuge and contamination cleanup efforts began. Three lime basins originally used to treat wastewater from the chemical production were decided to be contained in place, requiring a seepage barrier installed around the perimeter of the site to further prevent groundwater/contaminant migration. This case study will discuss the successful installation of a soil-bentonite cutoff wall around the area using deep soil mixing. Highlights of this case study will also include a discussion of the challenges faced due to construction activities performed with Level B Hazmat PPE requirements as well as added challenges brought on by the Winter season, after the project was delayed due to a positive air monitor detection for the chemical weapon Lewisite during construction of the work pad.INTRODUCTIONThe Rocky Mountain Arsenal (RMA), located just outside of Denver, Colorado, was established by the United States Army in 1942 to produce chemical warfare agents and incendiary munitions for use during World War II. Following the war, and as weapons production decreased, portions of the site were leased to private companies for the production of industrial and agricultural chemicals. The principal lessee, Shell Oil Company, manufactured mostly pesticides at RMA facilities from the early 1950s to the early 1980s.In 1984 an investigation began in accordance with the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) and confirmed significant levels of contamination due, in large part, to the common industrial and waste disposal practices of the era. It was also discovered that over 300 species of wildlife inhabited the land in the absence of regular human activity, including a group of bald eagles, leading to the passing of the Rocky Mountain Arsenal National Wildlife Refuge Act in 1992."

Jan 1, 2015

By Osama A. Safaqah

Driven plate anchors can be used to hold in place large bridge caissons during floating construction. Their small size and simple method of installation make them a very cost effective alternative to other direct-embedment, gravity, and drag anchors. The geotechnical design of plate anchors involves the anchor geometry, embedment, drivability, and proof testing. This paper describes the experience gained with plate anchors used during construction of the new Tacoma Narrows Bridge. For this project, the anchors had to be driven in dense to very dense sands, and had to resist large forces from 7-9 knot currents.

Jan 1, 2013

By Abhirami B., V. Balakumar

Piled raft foundation system is an intelligent geotechnical concept, developed towards reducing the settlement of the raft and the footings by providing pile elements below the raft or footings, as the case maybe. Although a large volume of works has been done on the behaviour of piled rafts by observational studies, the effect of construction methodologies such as deep excavations, the installation methodologies used for piling etc appear to have not been covered adequately. This paper discusses the effect of deep excavations, pile installation techniques and the effect of adding structural elements, based on the data available from published literatures. Based on this study, the performance of the piled raft monitored by the author has been revisited and the results of such a study are discussed.

Nov 1, 2022

By Jim Glider, Noah Miner

The Gordie Howe International Bridge is a project to build a cable-stayed bridge and border crossing across the Detroit River. With a span length of 2,800-ft (853.4 meters), the Gordie Howe International Bridge will have the longest main span of any cable-stayed bridge in North America. Each tower has two legs that are supported by six drilled shafts each for a total of 12. The tower shafts are 9.84 feet in diameter (3-m) and extend well into bedrock. 17 each, 6.6 feet (2-m) drilled shafts were built to support the aging river bulkhead and replace shipping bollards. In addition to shallow groundwater fed by the Detroit River, artesian conditions at depth result in a water head that is approximately 17.2-ft (5.2-m) above surface. At 95-ft (29-m) below grade Dundee Limestone, of the Detroit River Group, is moderately weathered and fracture density decreases with depth. The Dundee Limestone strength ranges from 8-ksi (55.1-MPa) to 12-ksi (82-MPa) and may carry hydrogen sulfide in fractures. Working through casing that sticks three stories out of the ground is less than ideal, but was necessary to maintain a positive fluid head and prevent artesian-related quality issues. The sheer scale of the bridge forces required a load test configuration that could impart an equivalent static load of over 38,000,000 pounds (170-MN). A suite of QA/QC tests was developed to ensure the shafts would meet the project plans and specifications to include critical base cleanliness criteria. Interesting CSL and TIP results obtained highlight the strengths and weaknesses of each test method. Cleaning drilling fluids with a centrifuge allowed recycling of product and reduced exposure to environmental contaminate exposure. Having large construction equipment working next to the river presented challenges in working pad design. A driven pile system was developed to support high oscillator forces and protect the aging seawall.

Sep 8, 2021

By David P. Sauls

Design-build contract delivery provides unique opportunities for efficiencies in pile foundation design and installation. The Louisiana Department of Transportation and Development (LADOTD) US Highway 90 at Louisiana State Highway 85 (US90/LA85) intersection was contracted under the design-build delivery system, in part to take advantage of these efficiencies. As one of five projects recognized by the Design Build Institute of America (DBIA) when it honored LADOTD as its 2011 Transportation Owner of the Year in the highway/bridges category, the design-build method provided a way for this project to be ?shovel-ready?, which enabled the LADOTD to secure American Recovery and Reinvestment Act (ARRA) funding. This paper describes the benefits this project gleaned from the design-build process, which included synergy, schedule, design and construction efficiencies, and team building. Interlaced with design and construction of precast prestressed concrete (PPC) piling in compressible southern Louisiana soils, the design-build process rapidly translated computations to cost and schedule savings. A robust quality assurance program using Pile Driving Analyzer (PDA) equipment to evaluate pile set-up provided expedited acceptance of bridge bents and advanced construction schedule. Data evaluation includes analyses of PDA data obtained from 1-hour, 24-hour, 7-day, 14-day and 6-month restrikes of the project test pile.

By Dempsey S. Thieman

Innovative marine bulkhead design and construction techniques were used in the fast-track design and construction of a high-capacity, deep-water dock in the highly seismic region of Alaska?s Aleutian Islands. The geotechnical investigation and design through construction phases were completed in just eight months. The adaptable OPEN CELL® design, readily available standard flat sheet pile and an experienced contractor were integral to the successful completion of the project. The cost of the structure was determined to be approximately 50 percent of a comparable pile-supported platform dock structure, allowed higher load capacity, rapid construction, less maintenance, and provided substantially more uplands. This paper details the design and construction of this unique and challenging project. The OPEN CELL structure is a vertical flexible membrane system that offers significant advantages over other structure types: ? Its flexible membrane structure is not dependent on toe embedment for stability. ? Poor soil conditions, shallow bedrock, high seismic loads, deep water, scour, etc., can be accommodated due to its adaptable design. ? It has a very high load capacity?capable of several thousand pounds per square foot. ? Allows buried utilities which results in lower cost and reduces freezing conditions ? The sheet pile tail walls can be extended to provide increased global stability if needed. ? Standard sheet pile and connectors with traditional installation techniques allow accelerated construction schedules.

Jan 1, 2008

By Parameswaran V. S, Anshuman Singh

This is a case study on ground improvement using Stone columns at Kokrajhar in Assam which comes under seismic Zone V as per IS: 1893. The strata at site comprised of mostly fine sands with low SPTN values, fine content less than 10% and ground water table (GWT) at shallow depth. As ground water table subjected to seasonal variation, water table is considered at ground level for designing purpose. The geotechnical profile of the boreholes was analysed on the guidelines of IS 1893 (Part 1) -2016 and it was observed that the liquefaction potential of the soil layers is prominent and ground improvement is inevitable up to a depth of 9.5 m below existing ground level. In order to mitigate the liquefaction of soil layer, Stone columns were proposed. The in-situ soil is densified using wet top feed vibroreplacement method with an area replacement ratio of 16%, so that the relative density of the soil can be enhanced to prevent liquefaction risk. Correlation between relative density, fines content and increment of SPT N –value given by Tokimatsu and Yoshimi (1983) was used for designing purpose. Field tests such as SPTs were carried out at site to validate the extent of SPT (N) improvement. Detail comparison of pre and post density, SPT N values and CRR values were discussed in this paper.

Nov 1, 2022

By Jon Huff, Jeffrey Donville, Hannah Iezzoni, Dan Stevenson

Occasionally, in the design of deep foundations for a structure, a single deep foundation element may be used to support a building column. The most common type of element used in such cases is a drilled shaft (also referred to as a drilled pier, caisson, or bored pile). However, as installation capabilities have improved, large diameter augercast piles are increasingly more common. While drilled shafts and augercast piles differ significantly in construction methods, in the eyes of the International Building Code (IBC), both are treated as cast-in-place deep foundations and must comply with many of the same code provisions. Deep foundations are required to be braced such that lateral stability is provided in all directions, however isolated, cast-in-place elements that have a diameter (D) of at least 2-feet and a length (L) not more than 12 times the diameter can be an exception. In response to the concerns raised by some member professionals, the Deep Foundations Institute’s (DFI) Augered Cast-in-Place Pile and Drilled Displacement Pile Committee took a closer look at the code and its applications, the historical development of the code language through the years and performed analytical modeling to evaluate the impact of this ratio on a pile’s stability. The question is whether the limiting ratio included in the IBC 2018 code provisions is justified, or whether different criteria should be used to determine when isolated deep foundation members are allowed.

Sep 8, 2021

By Brian Metcalfe, Kord Wissmann, Gianni Martinez

The Middle East consists of vast deserts that reach temperatures up to 50 degrees Celsius, with some areas characterized by endless sand dunes. When the project team selected the location for a large new transportation project, little did they know that the site would be characterized by soft, nearly normally consolidated silt and clay extending below a thin sand crust. Searching for solutions, the design team elected to reinforce the subsurface with Rammed Aggregate Pier® (RAP) ground improvement elements and desired verification that the novel method would stand the test of prolonged static loads. Because the concrete pavements would serve to spread the load, a “zone load test” was performed, consisting of applying a uniform bearing pressure of 150 kPa over a 7.5m square concrete footing. Unlike individual pier load tests, the zone test allowed the project engineers the opportunity to confirm design parameter values under large-loading area conditions, a situation not often available to most designers. This paper presents the results of the zone load test whose results may be interpreted to better understand design parameter values. This paper is of particular significance because it adds a value contribution to the relatively few numbers of “group load tests” available in the literature for ground improvement applications.

May 1, 2022

By Justin Simmons, Michael Arnold, Bob Faulhaber

"In order to remodel an existing beach resort on the Gulf of Mexico, an existing three story structure, founded on stepped tapered piles, was to be replaced by a ten-story building with service rooms on a daylight basement level, conference rooms on the next levels and up-scale hotel rooms on the upper levels. The new building was founded on augered-cast-in-place (ACIP) piles. The pile caps and the basement required excavations between nine and fifteen feet (three to five meters) below ground surface.BAUER Foundations Corp. (BFC) successfully used Cutter Soil Mixing (CSM) to install the support of excavation walls. This technique allowed for the adjustment of the wall alignment during execution in order to avoid existing and new piles and other underground obstructions. Nearly 1600 – 16-inch (400 mm diameter) ACIP piles were installed to an average depth of 71.5 feet (22m) below ground surface (BGS) by BFC to support the new hotel structure. Initial grout overages in piles were excessively high and ground stability issues were encountered in some pile locations. By identifying specific areas of concern BFC was able to modify the approach to ACIP installation, effectively mitigating the ongoing risks and successfully completed the project.PROJECTMarriott Hotels began the $300 million renovation and upgrade of their Marco Island Marriott Beach Club Hotel in Marco Island, FL to JW Marriott status in May 2015. The renovation included the demolition of a portion of their existing hotel tower, and the construction of a new 10-story hotel tower consisting of 94 new guest rooms and a 10,000 SF (900 m2) ballroom, among other amenities. As is typical with hotel construction, time was of the essence. The schedule was the driving factor of this project as the owner had already booked events in their new ballroom starting in January of 2017.BFC provided the client with a deep foundation package that included the installation of 1562 Augered Cast-In-Place (ACIP) piles supporting the new tower, and the design and construction of approximately 36,500 SF (3,400 m2) of soil-mixed retaining wall for support of excavation (SoE)."

Jan 1, 2017

By Heinrich Majewski, Rob Jameson

"Careful review of site conditions and constraints is essential to select the appropriate shoring system for each project. Key evaluation criteria include the geotechnical profile, groundwater and environmental conditions, adjacent buildings and utilities, schedule and any project specific access or other constraints. Typical earth retention schemes range from rock or soil nail walls, through conventional anchored pile and lagging walls to deep internally braced cut-off systems. The Owner’s design team will often develop the conceptual approach under their design studies, and this is refined with Contractor input through Design-Build or Design-Bid-Build procurement. In downtown San Francisco, underground construction must accommodate a unique combination of variable fill, soil, rock and groundwater conditions, potential for severe seismic loadings, and constrained sites within a dense urban environment. The quarter square mile of San Francisco’s Transbay and Rincon Hill districts has seen repeated cycles of development, destruction and re-building through earthquakes and the economy, and has been intensely redeveloped over the last decade. Over 50 acres of this land has been reclaimed from the Bay since the Gold Rush and within 3 city blocks the bedrock slopes from over 250 FT depth below the fills up to outcrops over 100 FT above sea level. A series of project examples from within this small area illustrate how varied shoring systems have accommodated the highly variable subsurface conditions while offering best value in terms of cost, schedule and appropriate protection of adjacent facilities.INTRODUCTIONA walk of 3 blocks from Rincon Hill on San Francisco’s Harrison Street, north through the Transbay area to Mission Street will traverse an urban zone which has been reinvented twice within its 150 year history in response to major seismic events. This small area highlights the range of subsurface conditions and urban environments which are encountered and accommodated in shoring schemes throughout the city. This route down the north side of Rincon Hill overlies a steep bedrock slope, outcropping over 100 FT above sea level at its south end and dropping to over 250 FT below sea level at Mission Street. A complex overburden soil profile, shaped by seismic activity and changing sea-levels has created layered soils ranging from soft estuary muds, dense sandy strata and deep clay layers, in turn topped with urban fill, frequently contaminated with debris from the Great 1906 earthquake. This route runs parallel to, and 350 yards inland of, the San Francisco shoreline resulting in groundwater elevation close to sea level with almost limitless recharge within granular layers. On the higher slopes of Rincon Hill, groundwater is typically observed flowing on top of and periodically within the fractured bedrock formation. The Transbay and Rincon areas were developed early in the Gold Rush era of San Francisco. After destruction in the 1906 earthquake and fire, they became a transit gateway into the city throughout the 20th Century. Demolition of the Embarcadero Freeway in response to earthquake damage and social pressure has opened this large area to redevelopment within the last 20 years, creating a new commercial and residential hub for the city. In its latest wave of building, planners are developing taller structures with deeper basements, in turn creating new construction challenges. Selection of shoring systems appropriate for these developments requires detailed evaluation. The process must address both the rapid spatial changes in subsurface conditions and the constraints surrounding, and specific to, each site in order to define shoring performance requirements. This paper presents an overview of the subsurface conditions and land use development of the Transbay and Rincon Hill areas, with examples of the shoring systems selected to meet site-specific conditions and requirements. The projects cited range from soil nail wall"

Jan 1, 2017

By Shields H. Arup

The paper describes the innovative foundation reuse and strengthening works for two buildings in Central London. A 1950s building on piled foundations (65 Whitfield St) and a 1930s building (67-69 Whitfield St) on 3m deep pad foundations were both extended upwards by two new stories. The Client for the project is Derwent London, with Make as their architect, Main Contractor Multiplex and Engineer Arup. Little was known about the foundations of either building at the start of the scheme. Extensive investigations of the existing foundations and ground conditions were carried out in both buildings. At 65 Whitfield St, investigations identified piled foundations, but found that pile lengths were short and variable. As a result, strengthening works solutions were adopted whereby the increase in column load was shed into new mini piles constructed around the existing pile caps. At 67-69 Whitfield St, deep pits were used to investigate the foundations and reuse was justified based on understanding of the pad dimensions, concrete strength, and strength and stiffness of the underlying geology. For both buildings the residual risk was closed out through monitoring during construction. The combined reuse of the structural frame and foundations of both buildings facilitated a sustainable solution, breathing a new lease of life into outdated buildings.

May 1, 2022

"The Metropolitan St. Louis Sewer District (MSD) in Missouri, the country’s fourth largest sewer system, is upgrading its storm and wastewater infrastructure in a 23-yearlong, $4.7 billion initiative called “Project Clear.” Historically, during times of intense precipitation, the current sewer system becomes overwhelmed. The primary goals of this project are to improve water quality and to alleviate many wastewater concerns in the St. Louis region by planning, designing and building community rainscaping, system improvements and an ambitious program of maintenance and repair.Part of the system renovation has focused on constructing underground tunnels for storm water storage, permitting controlled drainage of runoff, and preventing overflows into rivers and streams. Construction plans for these storage tunnels called for eight vertical intake and ventilation shafts to be bored from the ground surface. These shafts will then be intercepted in the bedrock at a depth of about 150 ft (45.7 m) during the excavation of the 3,000 ft (915 m) long underground tunnel that will be about 28 ft (8.5 m) in diameter. According to John Deeken , a geotechnical engineer with Black & Veatch Corp. and construction manager for the Maline Creek project, the drilling and blasting technique for creating the shafts was ruled out because the project was located in a residential neighborhood. “We could have used rock coring or a cutter head, but the drop shaft for this project is constructed within 10 ft (3.05 m) of an existing 108 in (274 cm) diameter sewer main,” Deeken said. “We had to take precautions to avoid damage to it.”A primary planning mandate of all MSD Project Clear phases requires minimized impact on traffic and residents. The canister drilling method enabled work to be confined to the median of a residential boulevard running perpendicular to the side street without detouring traffic. In addition, canister drilling offered a highly-precise means to create the shafts, leaving a smooth-sided borehole, right on target. Ground conditions in this 132 in (3.35 m) diameter intake shaft were wet due to the high groundwater levels and close proximity to the Mississippi River. “They’ve been finding shale in 2 to 6 ft (0.6 to 1.8 m) layers between weathered layers of Mississippian limestone,” said Dan Spiecher, technician at Center Rock (CRI). “The 2 ft (0.6 m) layers we can punch through. The 6 ft (1.8 m) layers slow us down.”"

Jan 1, 2017

By Jianhua Wang, Jianming Yao, Zhen Meng, Jinjian Chen

"Drilled screw pile is a newly developed displacement pile foundation which has been applied in soft clay for many years. Compared with traditional circular displacement pile, It is characterized by high bearing capacity, small volume and small squeezing effects. For the purpose of investigating the squeezing effects of drilled screw pile, a full scale field monitoring test with two test piles was performed. Detailed soil horizontal displacement and pore pressure measurements were conducted in the vicinity of the two drilled screw piles during penetration and subsequent soil consolidation. It can be concluded that the horizontal displacement of the surrounding soil induced by the installation of a drilled screw pile is mainly in a circular region with a diameter of 3 m (r/D<6), and the compaction effect outside the area can be essentially negligible; The excess pore pressures measured at the same time increase with depth throughout the entire process of consolidation, and its dissipation shows an exponential decay as a function of time.INTRODUCTIONA knowledge of the displacement and stress changes induced in the soil surrounding a pile is very important for evaluating pile performance. Numerous field and laboratory research projects have examined loading conditions, total soil stresses, and excess pore pressures during and following pile installation (Pestana et al., 2002). A relatively comprehensive and detailed review of these experimental works from 1948 to 2002 was presented by Pestana et al. (2002). More recently, Xu et al. (2006) conducted a field experiment to study displacements and stresses in the vicinity of two pipe piles during their installation in a soft lightly overconsolidated clay and compared the field measurements with existing predictive methods. Abdrabbo and Gaaver (2011) collected field observation data from four different construction sites to study soil disturbance during construction of piles using continuous flight auger (CFA). They have found that the disturbed zone of soil by CFA has a conical shape and the excess pore pressure has no appreciable influence on the load capacity of the piles.Drilled screw pile (DS pile) is a kind of vibration-free, cast-in-place concrete pile. Because of the excellent bearing performance, low level of vibration pollution and negligible spoil, as well as its fast construction speed, DS pile has been widely accepted by many engineers around the world. As a new type of drilled displacement pile, the significant installation effects of DS pile on the adjacent soil have not been systematically and integrally investigated yet. Since a proper numerical simulation of the real installation process of DS pile is difficult to achieve, the investigation based on field measurements is necessary. This paper presents a field investigation of the installation effects of two DS piles on surrounding soils. Detailed horizontal soil displacement and pore pressure measurements during pile installation and subsequent soil consolidation have been conducted. Based on the monitoring data, variation of horizontal displacements and dissipation of excess pore pressures with depth and time have been analyzed. What's more, the construction machinery and technology used in DS pile installation are also simply introduced."

Jan 1, 2015

By Masaru Sakakibara, Ngo Tuan Anh, Mitsuo Nozu

"In the southern region of Vietnam and the southern United States, numbers of Deep Mixing (DM) columns have been installed to increase the stability of slopes and mitigate ground settlement. However, in some cases, there were some quality problems for in-situ cement mixing such as inclusion of unmixed lumps. According to the investigations by the X-ray diffraction analyses, electrical conductivity (EC) test, and careful observations of in-situ mixing quality, it has been observed that the existence of expansive soil and its high EC value cause the insufficient in-situ mixing. The countermeasures to address these problems have been taken.INTRODUCTIONIn South Vietnam, under the guidance of numbers of references and standards (Miki, 1998, JGS, 2000, Kitazume et.al., 2001, BS 2005), Deep Mixing (DM) has been used in recent years for soft clay improvement to increase the stability of slopes and to reduce consolidation settlement (Nozu 2005, Tung et.al., 2009, S. T. G. Peng et.al, 2009). However, at the initial phase of the DM operation, the authors have encountered some unusual phenomena such as (1) lower strength and inclusion of unmixed lumps (Figure 1), (2) less amount of up-heaved soil, and (3) sticking of large lumps of clay to the mixing blades. In regard to the above (3), Photo 1 shows one of the countermeasures against the sticking. By means of the placement of additional plates, the stuck clay has been reduced significantly.Subsequently, we have noticed that the quality of DM columns has not been so good, which meant that there have been some unmixed lumps in the column despite high cement dosage such as more than 300kg/m3. The authors also have encountered the similar incidents in Vietnam and United States during the deep soil mixing work. For example, Photo 2 is the core samples taken from the DM test column in northern Vietnam adopting cement injection during penetration (CIDP) procedure. To solve this problem, various tests and investigations have been performed so far (Nozu 2010, 2012)."

Jan 1, 2015

By M Muzammil, S. Mukerjee, S. Saran, M. Bharathi

"This paper presents the results of in-situ tests conducted on a set of under-reamed piles in a silty sand deposit. Three piles (i.e. vertical, vertical with one bulb and vertical with two bulbs) of diameter 0.2 m were cast upto a depth of 5 m. The pile cap had four foundation bolts cast into it so that a mechanical oscillatormotor assembly could be mounted centrally on it. The oscillator-motor assembly was used to generate purely sinusoidal dynamic forces, in either horizontal or vertical directions. For both horizontal and vertical vibration cases, it was observed that (i) the natural frequencies decreased with an increase in the excitation force level, (ii) for the same excitation level, the natural frequencies as well as the maximum amplitude of vibration are almost the same irrespective of the pile geometry i.e. number of bulbs in the pile, indicating that the full pile length is not being excited. For the vertical vibration case, the soil-pile stiffness at frequencies, before resonance, were observed to be higher than those at frequencies after resonance. In the horizontal vibration case, the stiffness of the soil-pile system was found to be decreasing with an increase in the excitation force level. The damping ratio was found to be increasing with an increase in the excitation force level.INTRODUCTIONUnder-reamed piles are piles, normally upto a depth of 6 m, with one or more bulbs along the pile stem. These have been used for structures like transmission towers, structures on expansive soils etc. for a very long time, however it is only in the last 30 years that dynamic response of a pile has been studied. Evaluation of dynamic soil-pile interaction is a very complex problem as the conditions and properties of soil are highly variable and unpredictable. Various models and approaches have been suggested by various investigators for evaluating the dynamic soil-pile interaction problem, but most of them are based on the assumptions that the behaviour of soil is linear and the soil surrounding the pile is strongly adhered to it. But in practice, it is not so. The soil surrounding the pile is always somewhat loosened and undergoes some deformation when a sinusoidal load is applied. This causes the soil-pile system to behave nonlinearly.In earlier studies by Novak, (1974), Novak and Aboul-Ella, (1978) etc. a linear elastic behaviour of soil was assumed. This approach was very useful in understanding the mechanism of soil-pile interaction to a large extent. Subsequently various models were suggested like the lumped mass models with nonlinear discrete springs, dashpots and friction elements Matlock et al. (1978), weak cylindrical zone around the pile model Novak and Sheta, (1980), ideal boundary zone model with non-reflective interface, Han and Sabin, (1995) etc. These approximate solutions give an idea about the mechanism of dynamic pile-soil interaction to a large extent. However, in reality both separation and slippage can occur due to the formation of a weak bond at the contact surface between the soil and the pile when a dynamic load is applied. In addition, the soil column adjacent to the pile experiences large deformations under dynamic loads and thus behaves nonlinearly.Some computer aided model studies on the dynamic response of under-reamed piles have been reported, however, very few insitu dynamic tests on under-reamed piles are reported. Dynamic tests on piles were carried out by Novak and Grigg (1976) on small scale single piles and pile groups in the field. Similar field tests on small scale piles were conducted to study the nonlinear behaviour of a single pile and a pile group under strong harmonic excitation by Han and Novak (1988), Han and Vaziri (1992), Burr et al. (1997), Manna and Baidya (2010) etc. The majority of these experimental studies were focussed on the response of the specific pile groups and compared with the results of a single pile. Hence there was a need to study the influence of pile g"

Jan 1, 2015