Search Documents

By Johannes Labenski, Christian Moormann, Johannes Aschrafi

"Open steel pipe piles are used for various applications in costal engineering, port structures and increasingly important for offshore structures. During the installation of open steel pipe piles the formation of a plug has an influence on the installation process of the pile and also on the final bearing capacity. The formation of the plug depends on different factors, e.g. the pile diameter and the installation method. This paper starts with a structured overview about analytical methods (API, EAP-EAU, UWA-05, HKU-12, Modified API) to calculate the axial bearing capacity of open steel pipe piles. The numerical simulation of the installation process of open steel pipe piles has to fulfill high demands, i.e. to accurately represent the penetration of the pile inside the soil, the formation of the plug and also the stresses and strains during the installation. A numerical back analysis of a comprehensive field test, using the Coupled Eulerian-Lagrangian (CEL) method and a hypoplastic constitutive model for sand, reveals the stresses and displacements of the soil and of the piles. The analysis provides a comprehensive understanding of soilpile interaction.INTRODRUCTIONThe particular difficulty in the numerical simulation of plug formation, is that the effect of plugging inside open ended steel pipe piles has not been fully investigated. In scientific papers different approaches are documented to explain this phenomenon. Some are based on in-situ tests and others are based on numerical simulations. One of the challenges is to determine the end bearing capacity and shaft friction of the steel pipe pile. Different approaches have been developed over the years to determine them e.g. from Randolph et. al. (1991, 1994) and Paik et. al. (2003). Recent approaches are the ICP-05 Method (Jardine 2005), the UWA-05 Method (Lehane 2005) and the HKU-12 Method (Yu & Yang 2012a). A comparison of some methods can be found in Schneider et al. (2010). A plug inside an open steel pipe pile can be visualized as a spatial bracing of soil between the inner surfaces of the pile, cf. Lüking (2010).. However according to Lüking & Kempfert (2012) this bracing only exists for the height in the end of the pile equal to twice its diameter.To identify a plug inside a pile, there are different measurable parameters. One parameter is the development of stresses around the pile during and after its installation. Henke (2013) measured the inand outside horizontal stresses at the pile tip during the installation. The results showed higher stresses on the inside compared to the outside. To validate his measurements he performed a numerical back-analysis of the measured installation process and got matching results."

Jan 1, 2017

By Manuel M. Reyes, Thuraisamy Thavaraj, Alex Sy

"The new east span of the San Francisco-Oakland Bridge features a single tower self-anchored suspension (SAS) bridge. During construction of the SAS bridge, a temporary bridge was used to support the box girders until erection of suspension cables was completed. The transfer of deck load from the temporary bridge to the suspension cables was achieved in November 2012 and the SAS bridge has become the largest of its kind in the world. The new bridge will be in service in Fall 2013.Large diameter driven steel pipe piles were used for the temporary bridge foundations at Towers D, F and G located in San Francisco Bay. At Tower D, the large diameter steel pipe piles were driven through thin overburden into bedrock using a large Menck MHU500T hammer with a rated energy of 550 kJ. As there was no precedence in driving open-ended pipe piles into the Franciscan Formation bedrock, challenges were faced with uncertainties in drivability, driving stresses, pile embedment in bedrock and pile capacity. These uncertainties were addressed by incorporating additional measures into the pile design, and by the use of dynamic pile monitoring during initial driving and re-strike. Pile relaxation was observed during pile installation.At Towers F and G, setup effect was a key issue for the piles driven into the deep soft marine sediments. Drivability analyses were conducted to predict pile run, driving stresses, selection of hammer and refusal criteria. The piles were dynamically monitored during driving to estimate pile capacities. Due to the set-up effect in the Bay Mud, the piles gained up to 3.3 times the initial capacity during the re-strike and were in excess of the design capacity.This paper presents details of the design, construction, testing and performance of the driven pipe piles at temporary Towers D, F and G. Settlement data of the temporary tower foundations while in service confirmed the satisfactory performance of the pile foundations.INTRODUCTIONThe new east span of the San Francisco-Oakland Bay Bridge features a single tower self-anchored suspension (SAS) bridge, the largest of its kind in the world. The new east span replaces the existing double-deck steel bridge built in the mid-thirties. A span of the existing bridge had collapsed during the 1989 Loma Prieta earthquake but was repaired. Construction of the new east span commenced in 2008 and is expected to be completed for the Labour Day opening in 2013. Figure 1 shows a schematic (looking north) of the new bridge with its 160 m high main tower T1 in the middle, and Piers W2 and E2 at the west and east ends, respectively. The west and east spans of the SAS bridge are 180 m and 385 m, respectively.During construction of the SAS bridge, a temporary bridge, complete with towers and trusses, was used to support the box girders of the new permanent bridge until the loads from the box girders were transferred through suspension cables to the permanent bridge. The transfer of deck load from the temporary bridge to the main cable was completed in November 2012."

Jan 1, 2015

By Brian Wilson, Megan Atkinson, Richard Diggle, Nathan Sweeney

"Ruskin Dam, located near Mission, British Columbia, was constructed in 1929 and 1930 and comprises of a concrete gravity dam structure founded on bedrock. At the right abutment, which consists mostly of dense to very dense sands and silt, the dam abuts against overburden soils, and connects to a cutoff wall system consisting of sloping concrete slabs. Significant seepage and piping issues were encountered during first filling of the reservoir in 1930. In 2012, BC Hydro, the owner of the dam, awarded a contract for the construction of seepage control measures at the right abutment, including construction of a plastic concrete cut-off wall extending upstream of the dam, a plastic concrete seepage training wall extending downstream of the dam, tie-in of the new cutoff wall to the dam, consisting of jet grouting of the soils adjacent to the dam to allow for the construction of the special cutoff connecting the cutoff wall to the dam, and construction of additional jet-grouting ground improvement downstream of the dam.Integral to the upgrade was the requirement for the special tie-in cutoff wall, consisting of a highly flexible, impermeable membrane to connect the concrete dam to the new, 1 m thick plastic concrete cutoff wall. The tie-in extends vertically into bedrock through the dam and jet grout columns constructed adjacent and beneath the overhanging portion of the dam at the right abutment. The membrane is required to survive the anticipated earthquake induced deformation between the dam and the abutment soils.This paper describes the processes used to develop a material suitable to meet the specified flexibility and permeability criteria, as well as the innovative construction techniques utilized to construct the slot and place the bituminous material within it. The final dimensions of the slot were in the order of 7 m long by 25 m deep by 0.17 m wide. The bituminous material was placed under a head of water which was required to maintain stability of the slot, and was placed at temperatures in excess of 120 degrees Celsius."

Jan 1, 2017

By Amr M. Sallam

A case history of utilizing a mat foundation enhanced with ?settlement-control? piles to support a high-rise building in Downtown Orlando is presented. Original geotechnical engineering studies, performed by others, recommended pile foundations due to difficult soil conditions and highly variable loads. The value engineering study performed by the authors provided alternative foundation system of the mat foundation enhanced by ?settlement-control? piles. The alternative foundation system required few iterations of structural and geotechnical analysis. A target stiffness for the settlement-control piles was selected by the structural engineer. Pile load tests were performed to verify the recommended pile geometry. A total of 81 auger-cast-in-place settlement-control piles 45-foot long 16-inch diameter were installed. A total of 24 columns were monitored for settlement, which showed substantially less settlement than predicted. It is the authors? opinion that the ?settlement-control? piles increased the mat stiffness, relieved the concentration of contact pressures around heavily loaded columns, and reduced potential differential settlement. Mat foundation with settlement-control piles provided border-line foundation solution between shallow and deep foundations and has the potential to be widely used in Central Florida for similar subsoil and loading conditions; however a thorough analysis using three dimensional Finite Element Modeling may be needed to refine the geotechnical evaluations.

Jan 1, 2009

By Y. M. Ha, T. D. Nguyen, D. T. Nguyen, H. K. Choi

Conventionally, cement deep mixing (CDM) columns are designed to have constant diameters over the improved depth as this facilitates the construction procedures. However, this design pattern may be inefficient in cases of spread footings or shallow foundations. This paper first briefly introduces principles of an improved CDM method that can create head-enlarged CDM (termed PF) columns. A simple analysis approach was introduced to obtain optimal shape of PF columns that results in minimum settlement. The effectiveness of this improved method over the conventional CDM method was then illustrated by settlement analysis for an actual footing in a case study using two recommended analytical methods in the literature. Analysis results from the case indicated that by using the same amount of soil-cement mixed volumes, settlement from a footing on PF columns can reduce up to 10 % compared with that from the same footing on CDM columns. In addition, a material quantity comparison for the case indicated that to have the same settlement values the volume of each PF column can be reduced of around 10% compared with that of the CDM column. INTRODUCTION The cement deep mixing (CDM) method is one of the most popular methods in ground improvement works. Details on the method such as construction procedures, necessary equipment and recommendations are described in many references or manuals (e.g. Bruce et al. 2013, BS EN 2015, Kitazume and Terashi 2013). Conventionally, CDM columns are designed to have constant diameters over the improved depth as this facilitates the construction procedures. However, this design pattern is found inefficient in cases of spread footings or shallow foundations as the upper soil layers are naturally weaker than the deeper ones but are subjected to larger amount of induced stress from the superstructures.

Jan 1, 2019

By Erwin Stötzer, Renato Fiorotto, Wolfgang G. Brunner, Manfred Schöpf

"Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yie ld unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drill rig. With this system much deeper walls can be installed and even hard soil layers can be penetrated. CONVENTIONAL SOIL MIXINGIn 1962 Norman Liver patented an auger-based soil mixing technique that has become the basis for the world's current technology.The deep mixing method (DMM), as it is known today, is an in situ soil treatment and improvement technology where the soil is blended with binders and/or other materials that are introduced in a slurry or dry form.Typically one or more hollow, rotating mixing shafts tipped with some type of cutting tool are mounted vertically to the mast of a base carrier and are driven into the ground by hydraulic or electrically powered rotary heads. The shafts above the cutting tool may be further equipped with discontinuous auger flights and/or mixing paddles. The binder is injected through the hollow shafts to nozzles located near the cutting tool where it is mixed with the ground to form columns of treated soil.Individual column diameters range from 0,6m to 1,5m and may extend to 40 m in depth. They can be arranged individually or in contiguous or secant patterns to produce a wide range of treated soil structures on both land and marine projects. Typical configurations are: Single elements, rows of overlapping (secant) elements, grids, lattices and blocks (Fig. 1 )."

Jan 1, 2005

By Abolfazl Eslami, Sepide Lotfi, Mohammad M. Eslami

"Via direct CPT methods for pile capacity prediction, correlation coefficients smaller than unity are used to relate cone tip resistance (qc) and sleeve friction (fs) to pile toe capacity (rt) and shaft capacity (rs), respectively. For linking CPT data to pile capacity, factors such as diameter, penetration rate, partial embedment of pile toe into a hard layer, mechanism of plunging, failure zone, data processing, and stress-strain conditions must be considered. The aim of this paper is to investigate the role and significance of scale effects and establish direct relation between CPT data and pile shaft capacity. A database has been compiled including 40 full scale pile load tests and CPT sounding records for calibration and validation of the proposed approach. Analytical studies demonstrate that differences between pile and penetrometer penetration rate, geometry, and stress-strain conditions influence the relation between fs and rs. By considering the determinants, a procedure is proposed from which the pile shaft capacity can be predicted. This approach demonstrates better agreement with measured capacity by static loading test and less scatter than other current CPT methods.IntroductionAmong different approaches for pile capacity prediction, in-situ tests such as SPT and CPT have been used as supplementary of static analysis. Due to similarities between CPT and pile, the measured cone tip resistance and sleeve friction can be employed for prediction of unit toe and shaft capacities, respectively.Determination of pile capacity from CPT data includes two main approaches: direct and indirect methods. Direct CPT methods apply the measured values of cone tip resistance (qc) for pile toe capacity (rt), and sleeve friction (fs) for pile shaft capacity (rs) with some modifications regarding scale effects. Indirect CPT methods employ friction angle and undrained shear strength values that have been estimated from CPT data.When using direct CPT methods to relate qc and fs to rt and rs, correlation coefficients smaller than unity are used. Factors such as diameter, penetration rate, mechanism of plunging, failure zone, data processing, and stress-strain conditions must be considered for correlation between CPT and pile capacity. The work presented in this paper aims toward ameliorating the situation in the area of pile shaft capacity prediction, based on cone sleeve friction.Case histories from full-scale tests are compiled and analyzed by means of six methods including five direct CPT methods for shaft capacity prediction and the proposed method."

Jan 1, 2015

By Marco D. Boscardin, Kenneth A. Pidgeon, Adriane G. Boscardin

"Hollow bar tiebacks can offer an economical alternative to conventional solid bar and strand tieback systems for use in temporary excavation support construction. However, the limitations associated with the installation of hollow bar tiebacks require special attention during design, construction and load testing to verify conformance with conventional performance and proof testing criteria (PTI, 2014). In particular, providing a reliable free length is complicated by the 10-foot (3-m) -long, segmental, couplingto- coupling nature of the free length sheath in the hollow bar system, and addressing the fully grouted annulus of the bond zone and the free length zone at the end of installation are key concerns. In addition, it is often more convenient to install a greater number of more closely spaced, lower capacity tiebacks with the hollow bar system, compared to conventional tiebacks. This paper examines how these issues were addressed for a project involving a 60-foot (18-m) -deep sheet pile excavation through a highway embankment and a 70-foot-deep sheet pile and soldier pile and lagging excavation through a railroad embankment, both supported by a hybrid system of hollow bar tiebacks and hollow bar soil nails. The project involved approximately 300 tiebacks and 400 soil nails.INTRODUCTIONEngineers Construction, Inc. (ECI), constructed a pair of 32-foot (9.8-m) -wide (clear span), 30-foot (9- m) -high (21 feet (6.4 m) above the stream bed), cast-in-place concrete arch culverts as a design-build project for the Vermont Agency of Transportation (VTrans) in East Ryegate, Vermont. The new culverts replaced an existing 8-foot (2.4-m) -wide by 6-foot (1.8-m) -high cast-in-place concrete culvert under US Route 5 (RTE5), and twin, 2-foot (0.6-m) -wide by 5-foot (1.5-m) -high granite block culverts under the Washington County Railroad (WACR) alignment. The culverts convey Manchester Brook eastward, through the embankments for RTE5 and the WACR, on its way to the Connecticut River. The Connecticut River is located approximately 100 feet (30 m) east of the WACR embankment. The existing structures were undersized and backed up water behind the embankments during high flow events; and often trapped debris that flowed down the brook and became clogged. The existing culverts also had cracks and openings that have resulted in the loss of ground into the culverts and the formation of sinkholes in the sides of the embankments. Moreover, the reason for the large cross-sectional dimensions of the culverts was to make them of sufficient size and openness to encourage the migration of fish up the stream to spawn. The culvert through the RTE5 embankment is 144 feet (44 m) long, and the culvert through the WACR embankment is 128 feet (39 m) long, with a 57-foot (17.4-m) -long by 32–foot (9.8- m) -wide by 17-foot (5.2-m) -deep 10 feet (3 m) deep above the stream bed) open channel section between the two culverts. A plan view of the culvert alignment is presented in Figure 1."

Jan 1, 2016

By Sowmiyaa. V. S., Tiruvengala Padma

Axial compression capacities of bored cast in situ piles as per Indian and International Standards are compared in this paper. Bored cast in-situ piles resting on soil and rock are considered for capacity assessment comparison. The standards considered for comparison are Indian Standards namely IS 2911-Part 1-Sec 2:2010 and IRC 78, International Standards like AASHTO LRFD Design-2017, API 2A WSD, BS 8004:2015 & EN 1997: Part 1:2014. The end bearing mobilization limits as proposed by various standards and their influence on longer piles in cohesive and cohesionless soils are discussed.

Sep 1, 2022

By Nick Hytiris, Mohammed Al Maadheedi, Slobodan B. Mickovski

This paper explores the capacity effects of a square steel plate welded at the ground surface on a driven open-ended steel pile (i.e. the plate would touch the ground surface after the pile achieves the required penetration). A series of strain-controlled, 1-g laboratory tests were undertaken on piles with and without a square steel plate attached. The piles were driven in dry, loosely packed, uniform sand. Two plates were used, one with a breadth equal to two times the diameter of the pile (2D) and the other with a breadth equal to three times the diameter of the piles (3D). A 20% increase in capacity was recorded for the 2D plate, and a 110% increase in capacity was recorded for the 3D plate when compared to the pile without an attached steel plate. The back-analysis of the results allowed the derivation of a new expression to calculate the capacity of bearing plates, which accounted for the effects of sands compaction and dilation. By extrapolating the findings of these tests to a hypothetical scenario, a model design problem was described where the length of a pile can be reduced by 20% to 60% (depending on the load) by using a plate attached to the pile. The results of this study can help designers to minimise penetration depth; thus, achieving a more economical and sustainable design.

By Mohammed Al Maadheedi

This paper explores the capacity effects of a square steel plate welded at the ground surface on a driven open-ended steel pile (i.e. the plate would touch the ground surface after the pile achieves the required penetration). A series of strain-controlled, 1-g laboratory tests were undertaken on piles with and without a square steel plate attached. The piles were driven in dry, loosely packed, uniform sand. Two plates were used, one with a breadth equal to two times the diameter of the pile (2D) and the other with a breadth equal to three times the diameter of the piles (3D). A 20% increase in capacity was recorded for the 2D plate, and a 110% increase in capacity was recorded for the 3D plate when compared to the pile without an attached steel plate. The back-analysis of the results allowed the derivation of a new expression to calculate the capacity of bearing plates, which accounted for the effects of sands compaction and dilation. By extrapolating the findings of these tests to a hypothetical scenario, a model design problem was described where the length of a pile can be reduced by 20% to 60% (depending on the load) by using a plate attached to the pile. The results of this study can help designers to minimise penetration depth; thus, achieving a more economical and sustainable design.

By George Aristorenas, Carlos Englert, Jesús Gómez

"Laboratory test data of strain softening soils exhibit the development of a maximum (peak) shear strength followed by a decrease in the strength with continued straining. The rate of strength loss decreases such that an asymptotic minimum value, known as the residual strength, is approached. This paper presents an investigation of the evolution of strength degradation in excavation supported soils that exhibit strain softening behavior. The paper presents a numerical investigation of excavation support of slicken-sided clay, and results of shear testing on materials with similar strain softening behavior. A strain softening constitutive law is presented that can be used with the finite element computer software Plaxis for analysis of excavation support. A typical design section of a deep excavation support in stiff, fissured clay is presented that illustrates the limitations and conservatism of the residual strength approach for excavation support design. Finally, a discussion is presented on the impact of stiffer walls such as diaphragm walls, compared to less stiff systems such as sheet piles, on the design parameters.INTRODUCTIONIn the Washington, D.C. metropolitan area, the Potomac Formation is generally composed of stiff, fissured clays. Geotechnical engineers often associate the presence of slicken-sided planes within the formation as evidence that the soil cannot develop its peak strength. Although it is unclear how old and continuous these slicken-sided planes are, their occurrence, persistence and orientation appear to be somewhat random. Due to this uncertainty, the design of open cut slopes in these materials is often conservatively performed assuming residual shear strength values. This design approach may be justified for long-term open cuts when there is limited amount of geotechnical information and in view of back stability analyses of past slope failures. Furthermore, the lack of confinement in open cuts allows relatively high shear strains near the surface and toe throughout their existence, which promote mobilization of post-peak strength values and the ensuing progressive failure. Indeed, such behavior has been discussed in the past (Skempton, 1970; Schnabel et. al., 1982; Derrenbacher, 1998). A thorough study by Mesri et. al. (2003) of numerous slope failures concludes that the lower bound strength for stability analysis of non-failed slopes is the fully softened strength, which is intermediate between the peak and residual strengths, but that part of the slip surface may be in a residual condition prior to failure."

Jan 1, 2015

By Arash Khosravifar, Amalia Giannakou

"Nonlinear foundation springs for bridge caisson foundations show significant coupling between the shear force and bending moment. Implementing foundation stiffness matrix with coupling effects (off-diagonal components) into the global bridge model presents numerical challenges. A simplified approach is developed to model foundation springs including coupling effects using a simple methodology. This simplified model include one translational spring and one rotational spring combined with a rigid link in 2D space. Results show that nonlinear springs (translational, rotational and coupling) can be reasonably captured using this simplified procedure.INTRODUCTIONThe Izmit Bay Bridge is a 3-km long suspension bridge that crosses Izmit Bay in Turkey and is being constructed in a highly seismic region. Figure 1 shows the project location. The South Approach Viaduct (SAV), located along the western margin of Hersek peninsula, is within 5 km from the North Anatolian Fault and within a zone of secondary deformation around the primary trace of the North Anatolian Fault. The proposed SAV consists of 11 Piers and an abutment at the south end of the structure."

Jan 1, 2017

By George C. Webb

A wide variety and variable depth (up to 40 ft.) of compressible, uncontrolled fill (including construction debris and a perched water condition) was present at a proposed Kroger construction site in Dent, Ohio. An innovative solution using a combination of an ACIP foundation system with a Tensar geogrid reinforced load distribution platform was used to provide a high quality building pad. This system allowed the use of conventional shallow foundations for structure support. This system was used in lieu of more costly solutions, such as complete undercutting of the entire existing fill and replacement with engineered fill or a deep foundation/ structural slab system. The selected ground modification included a system of augercast piles bearing on shale bedrock, which were installed on a grid pattern over the entire building footprint. Then, three layers of Tensar polyproplene biaxial geogrid were used to create a reinforced soil mat, which was supported on the augercast piles. An eight-foot blanket of engineered fill was placed above the geogrid-reinforced mattress fill to establish the building subgrade elevation. Standard shallow footings and slab-on-grade construction methods were then used to support the 26-ft. tall masonry block building. A small-scale instrumentation program included monitoring the geogrid reinforced mat settlement, geogrid strain and earth pressure distribution under the reinforced mat to evaluate design assumptions and theoretical analyses. This case history describes the first application of a pile supported geogrid reinforced mat for structure support which has been documented in the United States.

Jan 1, 2003

By Shoji Higashi, Nobuhiro Honda, Takeo Asanuma, Tatsuo Nagatsu, Masaki Kitazume, Sachihiko Tokunaga, Shigeru Kubo, Hidenori Takahashi, Tsuneyasu Onishi, Yoshiyuki Morikawa

"Various kinds of civil engineering structures and facilities were seriously damaged in the earthquake in Tohoku and Kanto regions of Japan on 11 March 2011 due to the greatness of its magnitude. In contrast, many structures resisted the large seismic force having been reinforced by the CDM (Cement Deep Mixing) method, which is often used for increasing the bearing capacity of ground and improving seismic performance. This paper summarizes the field survey undertaken to investigate damage to structures and facilities reinforced by the CDM method. Several prefectures and metropolitan areas were selected for the survey, based on the occurrence of strong seismic motions. A total of 847 structures and facilities were studied, in the survey using a questionnaire, which mainly inquired about the appearance of structures and facilities. Of the respondents to the questionnaire, 789 replied that there were no seriously damaged structures. The paper presents the damaged and non-damaged sites of CDM-technique sites and non-CDM-techniques sites. It can be concluded from the field survey that the CDM Method demonstrates high efficacy and durability against a strong seismic motions.INTRODUCTIONDuring the afternoon of 11 March, 2011, a huge magnitude-9.0 Mw (Category 9.0 on the Richter scale) earthquake occurred about 25 kilometers below the Pacific Ocean’s surface off the coast of Tohoku. This massive earthquake, now called the 2011 Off the Pacific Coast of Tohoku Earthquake was the largest earthquake ever observed in Japan. The seismic intensity of this earthquake was measured 7, the maximum on the Japanese intensity scale, as observed 7 in northern Miyagi Prefecture. The earthquake caused severe damage over a wide area from Tohoku to Kanto, and triggered large tsunamis that struck the Pacific coast of Hokkaido, Tohoku, and Kanto. The number of missing and fatalities caused by this earthquake exceeded 18,000 persons, making this an unparalleled earthquake disaster with a cost-in-life toll not experienced by Japan in recent years. Because of the scale of its seismic motions, the earthquake damaged facilities and structures of many kinds. In the years prior to this earthquake, the CDM method was used extensively to increase the bearing capacity of the ground as an anti-seismic countermeasure and to prevent liquefaction. Immediately after the earthquake, the CDM Association visually surveyed the state of damage to about 800 facilities in the Tohoku and Kanto regions where a seismic intensity of 5 or higher was observed. This report summarizes the survey of damage to facilities and structures constructed applying the CDM method in order to confirm the durability and performance of the method against seismic motions."

Jan 1, 2015

By Thomas Billups, Brendan FitzPatrick, Doug LeDo, David Carchedi

"Working in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical analysis and design. These challenges often include working on sites with limited access and laydown area, vibration concerns for adjacent structures and the need to work from variable elevations or within excavations. This paper describes the use of the modular Ductile Iron Pile system, a low-vibration driven micropile, on two urban projects on the Johnson & Wales University campus in Providence, Rhode Island. The paper describes the successful implementation of Ductile Iron Piles installed to develop capacity in end-bearing on one site and friction on the second site. Design, installation and quality control operations are all presented as well as the results of full-scale load testing performed on non-production test piles. This paper is of importance to the industry because it describes a versatile option for project teams as an alternative to traditional micropiles, helical piles or other deep foundation systems for urban sites.INTRODUCTIONWorking in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical analysis and design. These challenges often include working on sites with limited access and laydown area, vibration concerns for adjacent structures and the need to work from variable elevations or within excavations. Two recent projects in downtown Providence, Rhode Island faced a combination of problematic soil conditions and urban construction challenges including vibration concerns. Both projects were a part of the Johnson and Wales University campus development. Figure 1 illustrates the urban locations of the sites."

Jan 1, 2016

By George C. Webb

A wide variety and variable depth (up to 40 ft.) of compressible, uncontrolled fill (including construction debris and a perched water condition) was present at a proposed Kroger construction site in Dent, Ohio. An innovative solution using a combination of an ACIP foundation system with a Tensar geogrid reinforced load distribution platform was used to provide a high quality building pad. This system allowed the use of conventional shallow foundations for structure support. This system was used in lieu of more costly solutions, such as complete undercutting of the entire existing fill and replacement with engineered fill or a deep foundation/ structural slab system. The selected ground modification included a system of augercast piles bearing on shale bedrock, which were installed on a grid pattern over the entire building footprint. Then, three layers of Tensar polypropylene biaxial geogrid were used to create a reinforced soil mat, which was supported on the augercast piles. An eight-foot blanket of engineered fill was placed above the geogrid-reinforced mattress fill to establish the building subgrade elevation. Standard shallow footings and slab-on-grade construction methods were then used to support the 26-ft. tall masonry block building. A small-scale instrumentation program included monitoring the geogrid reinforced mat settlement, geogrid strain and earth pressure distribution under the reinforced mat to evaluate design assumptions and theoretical analyses. This case history describes the first application of a pile supported geogrid reinforced mat for structure support which has been documented in the United States.

Jan 1, 2005

By Mario Mauro, Jeff Taylor, Carlos Morales

"In 2007 the US Army Corps of Engineers classified the Herbert Hoover Dike in Florida as a Dam Safety Action Classification (DSAC) 1 dam, and started the implementation of one of the largest dam rehabilitation projects in the nation. The construction of the cutoff wall is a key feature of this rehabilitation work to upgrade the dike to current dam safety criteria. The cutoff wall installation is currently being completed on Reach 1, which extends from Port Mayaca to Belle Glade, under a Multiple Task Order Contract based on performance specifications and stringent verification criteria.For the construction of the cutoff wall TREVIICOS selected the self-hardening slurry method. Since the cutoff wall is installed through a layer of highly variable limestone with Unconfined Compressive Strength (UCS) up to 14,000 psi, the excavation requires the use of the hydromill equipment. This is the first successful application of the hydromill technology with self-hardening slurry in a large scale project in the US. This paper presents the details of the method utilized, the quality control procedures, and the experience gained over seven miles of cutoff wall installed.INTRODUCTIONProject LocationThe Herbert Hoover Dike (HHD) system, around Lake Okeechobee in South Florida, consists of a series of levees, culverts and locks and is approximately 143 miles long (Figure 1).Lake Okeechobee is the second largest freshwater lake in the lower 48 states of the United States. The lake is the primary drinking water source for numerous communities around the lake and to millions of people living along the lower east coast. The lake is also a vital source of irrigation for the agricultural industry in the South Florida region.Lake Okeechobee is 33 miles wide from north to south and 30 miles wide from east to west and has a surface area of 730 square miles. The average water depth of the lake is 9 ft."

Jan 1, 2017

By Abid O. Adekunte

The design, construction and monitoring of the deep excavation support for the basement of a large-scale commercial development in Cavan, Ireland is presented. Excavation area was adjacent to existing structures and retained height H varied between 4.0m ? 11.0m. In areas where excavation depth H < 5.0m, wall was designed as cantilevered section. However in sections where 5.0m = H = 11m, additional wall supports were required for serviceability reasons. Traditionally, designers often provide additional wall support through the use of tie-back ground anchors, raking props and braces. On the current project, the main contractor was not in support of the use of temporary props so as to maximise working space, while owners of adjacent properties disapproved the use of tie-backs. The limited set-back between the wall line and site boundary also contributed to the complexity of the project. A rare alternative solution has been adopted. This novel approach involved buttressing the wall with steeply raking bored tension piles at regular intervals along the wall. Comparison of the monitored deflections in the cantilevered sections with those recorded at sections where tension piles were used shows the novel solution to be safe and quite effective. This approach is also considered to be more economical when compared with ground anchorage and propping.

Jan 1, 2008

By R. Radhakrishnan, C. Gunasekaran

"Calicut Bypass Phase-II project included construction of 7 m high embankment over soft compressible clays up to 18 m in thickness. Approx 1.5 km length of road out of a total 5 km length consisted of abandoned paddy fields which were low lying, waterlogged and marshy in nature. On the basis of excellent results achieved in earlier phases of the by-pass construction, ground improvement work by installing pre-fabricated vertical drains (PVD) was undertaken to stabilize the embankment foundation along the weak clay areas prior to road pavement construction to avoid large post construction settlement as well as to improve the lateral stability during and after embankment construction. This project perhaps stands out as one of the highway projects completed within a very short time period of total 18 months including four month long heavy monsoon period, when embankment construction was not possible and construction of two bridges across rivers. All activities including the ground improvement had to be programmed and completed within the shortest time period possible. The paper discusses details of the extensive ground improvement and soil instrumentation carried out for the project and will illustrate how careful planning and execution can reduce the period required for highway projects involving ground improvement.INTRODUCTIONPhase-II construction of Calicut by-pass was undertaken on a priority basis by the State of Kerala in 2014. The main contract was awarded to M/S ULCCS Ltd, Kozhikode, Kerala and the ground improvement work was awarded to M/S Geo-Enviro Engineers P Ltd, as specialist agency to design and execute the work.Soil investigation carried out confirmed thick soft clay deposits below GL in three areas along the road alignment totaling approx 1.5 km in length. These areas were low lying, waterlogged and marshy in nature. Highway embankment had to be constructed up to 7 m in height above existing GL to form the proposed road alignment along these areas. On the basis of excellent results achieved in earlier phases of the by-pass construction using pre-fabricated vertical drains or PVD (R. Radhakrishnan, 2006), ground improvement using PVD had been included in the contract to stabilize the embankment foundation along the weak clay areas prior to highway embankment construction to avoid large post construction settlement as well as to improve lateral stability during its construction."

Jan 1, 2015