Search Documents

By Edward Jacobsen, Patrick J. Lydon

"The ongoing expansion of the Oak Creek Power Plant in Oak Creek, Wisc., includes a tunnel bored in rock that connects to four vertical intake shafts approximately 1.5 miles (2.4 km) offshore in Lake Michigan. In 2004, Case Foundation Company was awarded a lump sum contract to install these intake shafts. In spite of delays that shortened the May to September construction season by up to 50%, four shafts and liner assemblies were drilled in 2005 and 2006. The shafts were connected to the tunnel in 2007 by mining upward to reach the lower portion of each liner and then removing its internal bulkheads so that lake water fl owed into the tunnel. The project is one of the largest private construction projects ever undertaken in Wisconsin. The expansion adds 1,230 megawatts of generation. In addition to the tunnel and offshore work, there will be 16 miles (26 km) of railroad track and 6 million cubic yards (4,600,000 m3) of earth work. The 27 ft (8.2 m) diameter tunnel, drilled some 150 ft (46 m) below the surface of Lake Michigan, originates onshore at a pump house. A structural slurry wall was constructed as the foundation for the pump house. The tunnel passes to the south near the current water intake before bearing east toward the new offshore intake shafts, which are 12 ft (3.6 m) diameter by 108 ft (33 m) long steel liner assemblies. These were grouted in place from approximately 3 ft (1 m) above the crown of the intake tunnel and then to 20 ft (6 m) below the lake bottom.Site GeologyOffshore. The plant site is north of the Racine-Milwaukee county line in an area affected by glacial activity. The soil conditions encountered at each shaft location were consistent, with noticeable variations occurring in the top of rock elevations that sloped downward from the innermost to the outermost shaft."

Jan 1, 2008

By António A. Henriques, António Gomes Correia, Ana Teixeira

"Abstract Pile foundations are often used for important structures, and thus, reliability evaluation is an important aspect of the design. Reliability methods have become increasingly important as decision support tools in different areas. The main benefit of reliability analysis is that it provides quantitative information about the parameters (uncertainties) that most significantly influence the behaviour under study. In particular, the design of pile foundations still involves many limitations and uncertainties, particularly when there is not enough investment in soil characterisation and/or pile load tests. In addition to the uncertainties associated with soil characterisation, physical, statistical, spatial and human uncertainties exist. In this subject, the primary purpose of this paper is to demonstrate the application of reliability methods to geotechnical pile design (axial load). It also presents a simple and practical approach to performing it using Monte Carlo Simulations, intending to provide knowledge for code harmonisation and encouraging the development of such methodologies in geotechnical practice. Sensitivity analyses are shown to understand the influence of each uncertainty type coming from different sources. An application example indicates, corroborating other studies, that the model error is the most influent uncertainty. As such, when using the different models (SPT-, CPT- and PMT-based) for bearing capacity, the results emphasise the need for a well-defined and wellcharacterised resistance model, also these results allow the engineer to understand how important the load tests can be to achieve reliable results and economic designs.1 IntroductionUnlike the approach to reliability evaluation used in structural engineering, the traditional procedure used in geotechnical designs addresses uncertainties through high global or partial safety factors (SF), mostly based on past experience. However, this approach to addressing uncertainties does not provide a rational basis for understanding their influence on design.Furthermore, the new regulation codes and social concerns, such as the sustainability or the economy, are imposing geotechnical engineers to increase their ability to deal with uncertainty in a direct and more rational way. Designs should be economic, sustainable and reliable at the same time. Concerning the reliability part of design, different approaches can be done, but the most important thing to keep in mind is the simplicity and efficiency of the tools and applied methods."

Jan 1, 2014

By Derrick Dasenbrock, Mary C. Nodine, Benjamin Rivers

Up to 50 percent of major infrastructure projects suffer impacts to schedule or cost due to geotechnical issues, many of which correspond to risks related directly or indirectly to the scope and quality of site characterization work. The Federal Highway Administration (FHWA) in coordination with industry organizations seeks to address this issue through Every Day Counts (EDC), a program that identifies and deploys proven, yet underutilized innovations at the project level to save time, money and resources. The A-GaME (Advanced Geotechnical Methods in Exploration) is one of the innovations supported under EDC.

By Dan Brown

A method is outlined for computing the contribution of a micropile group to global stability of a sliding mass. The forces in the micropile are computed in a way which accounts for the effect of soil mass movement on the mobilization of axial and shear forces and which maintains compatibility between shear and axial force as a function of displacement. The method provides a rigorous model to incorporate the pile forces into the stability calculations, including the effect of pile forces on the resultant shear and normal forces at the sliding surface. This paper demonstrates the proposed solution using a simple example slope.

Jan 1, 2007

By Patrick J. Hannigan, Alex Ryberg, Rozbeh B. Moghaddam

Driven piles are widely used for foundation support. In the vast majority of cases, an increase in pile capacity occurs with time which is referred to as “set-up.” However, in a very limited number of cases, a decrease in capacity with time can occur. This phenomenon is referred to as “relaxation.” This paper will provide a brief review of the relaxation phenomenon, as well as pile driving information and dynamic test data on cases where relaxation has occurred. The pile types in the presented relaxation cases include H-piles, open-end and closed-end pipe piles, prestressed concrete piles, and prestressed concrete piles with H-pile stingers. The soil conditions where relaxation occurred includes dense to very dense fine sands, heavily over consolidated clays, and weak laminated rocks. Relaxation information from 36 piles at 26 sites is assessed. The collected data will assist foundation designers by identifying the subsurface conditions where relaxation has occurred, as well as by documenting the corresponding relaxation magnitude. One method of addressing relaxation when it is encountered is to drive the foundation piles to a greater end of initial driving capacity than required long-term. Hence, the identification and quantification of the relaxation magnitude will be beneficial to foundation designers installing similar pile types in similar subsurface conditions. The paper will also present pertinent observations and recommendations on mitigating relaxation when encountered. INTRODUCTION One of the earliest observations of a decrease in redriving resistance following initial driving was reported by Miller (1937). He reported that piles driven into a saturated, coarse grained soil could lose 40 to 50% of their resistance when redriven 24 hours after initial driving. Yang (1956) similarly reported that after a break in driving, a decrease in driving resistance could be encountered for piles driven in dense fine sand, inorganic silt, or stiff fissured clay. Parsons (1966) in his paper that described piling difficulties in the New York City metropolitan area termed this phenomenon “relaxation”. In this time period, pile capacity was most often evaluated from a pile driving formula frequently checked by a static load test. Hence, the true magnitude of the capacity decrease on a given pile was often poorly quantified. Furthermore, dynamic measurements that could determine what influence driving system performance variation had on the observed redriving resistance were not yet readily available.

Jan 1, 2019

By James A. Schneider

The evolution of the American Petroleum Institute (API) design method for axial capacity of driven piles in siliceous sands is explored, and complemented with an overview of how changes in offshore site investigation practice have increased the level of knowledge with respect to vertical variability of soil characteristics. Increased use of the cone penetration test (CPT) provides near continuous profiles of soil type and strength which can be used in calculation methods that address variation in local shaft friction rather than the API method which seems to have initially been based on observations of average shaft friction in relatively uniform sand deposits. Development of a formulation for CPT correlations to axial pile capacity in sand is discussed, along with implications to existing factors of safety used in routine design.

Jan 1, 2006

By JO Choi

Jet-grouting method is a useful technique to reinforce foundations on relatively soft or vulnerable soil layers such as fractured zone and stratum with cavities. Although jet-grouting has been widely applied to various field works, a reliable design standard has not been established yet. A number of model tests were performed to investigate end bearing behaviors of piles reinforced by jet-grouting. It was concluded that end bearing capacity was increased in proportion to uniaxial compressive strength of grout column. Based on the test results, the design criteria for the end bearing capacity were suggested.

Jan 1, 2006

By Seung-hoon Lee

The use of piled raft foundations has been considered as an economical alternative to conventional piled foundations because a portion of the applied load is carried by the raft in the design of piled raft foundation. In analyzing the behavior of a piled raft foundation as a settlement reducer, an accurate estimate of settlements of the system should be made on the basis of the understanding of nonlinear behavior of piles in layered soils as well as the interaction between the raft, soils, and piles. Although the 3-dimensional finite element method and simplified analysis methods have been used for the design of piled raft foundations, these methods were found to be inadequate for the practical purpose or could not consider the interactions properly. This study developed an approximate hybrid method of analysis to be used for the practical design of piled raft foundations considering pile-soil, raft-soil, pile-soil-pile and raft-soil-pile interactions. In the presented method of analysis, the settlements of the system are estimated satisfying the compatibility of two separate models which are the flexible raft model consisting of 2-dimensional finite elements supported by springs representing soils and piles, and the group-pile model embedded in layers of soil having different properties. Comparisons with other analytical methods as well as a 3-dimensional FEM program were made to verify the sufficient capabilities of the proposed hybrid model for application to practical design and analysis of piled raft foundations.

Jan 1, 2008

By J. -M. Rescoussier

Due to Important settlements inducing major structural damages, the western part of the Grand Littoral shopping centre has been closed in 1997. The present paper describes the project of underpinning including not only micropiles under the structure of the building but also a reinforcement of the soil located between the shopping centre and the edge of the embankment surrounding the western part of the shopping centre. The aim of this reinforcement is to reduce existing horizontal movements to allowable values.

Jan 1, 2002

By James E. Maccariella

Replacement of an existing movable bridge with a new low level fixed bridge would not accommodate potential future navigation traffic. In order to replace the existing bridge in a cost effective manner, while accommodating the potential future needs of the Port of Salem, a new bridge was proposed that would permit conversion to a vertical lift type movable bridge should a potential need for upstream navigation warrant such a project in the future. Drilled shafts were found to be the most desirable foundation type for the replacement of the Route 49 Bridge over Salem River. Their ability to resist scour, be constructed without cofferdams, adequately resist vessel collision forces, and accommodate conversion to a future vertical lift bridge allowed the project to meet both the needs of the New Jersey Department of Transportation and the Port of Salem.

Jan 1, 2005

By Marie-Pierre Bourdouxhe-Barnich

Since 1997, in partnership with the Laboratoire Central des Ponts et Chaussées in Strasbourg, ProfilARBED has been carrying out a vast study to qualify the improvements jetting can make to vibratory driving of steel sheet piles, and to understand its effect on the surrounding ground and on the sheet piles themselves. The process basically involves discharging a fluid (mostly water, sometimes in association with air) at controlled pressure and/or flow rate near the toe of the sheet pile being driven. The steel jetting pipes are attached to the sheet pile and are connected to the pumps by hoses. The jet of fluid loosens the soil, thus reducing the resistance at the toe of the sheet pile. Depending on ground conditions, the fluid that flows along the pile can reduce skin friction. Four soil types were involved in our experiments. Each site was instrumented: the driving parameters and the geotechnical characteristics of the soil before and after vibratory driving and jetting-assisted driving were recorded. Each test provided its own particular information which contributes to overall thinking on the matter and is of help to project managers who are often confronted with rapid driving to the final depth.

Jan 1, 2002

By Chu E. Ho

Key variables that govern the jet cutting process are examined based on fundamental theories of jet hydrodynamics and soil mechanics. Under normal conditions of jet grouting operations, lift speed and rotation speed are found to be of less importance than the depth of jetting, nozzle pressure, nozzle diameter, and the soil bearing resistance, with regards to their influence on jet cutting distance. An analytical equation linking the governing variables is proposed, which allows for the possibility of evaluating column diameters achievable in different ground conditions based on theoretical calculations. When used in conjunction with shallow jet grouting field trials, the equation can provide a means for extrapolating trial results to conditions at actual depths for production jet grouting.

Jan 1, 2006

By Sara Anderson, Rachel Nicholls, Tim Chapman, Janice Windle

"In city center sites around the world, and in particular in London, foundation reuse is becoming increasingly widespread as the ground is filled with detritus from previous developments. This paper sets out a systematic framework to consider the need for and benefits of foundation reuse and key issues to be resolved for foundation reuse to be successfully adopted on redevelopment projects. Once foundation reuse has been identified as a potential foundation solution there are several key stages in the design and construction process where the decision to reuse foundations needs to be assessed. The paper concludes by emphasising the importance of ensuring that the foundations being installed now can more easily be reused in the future.INTRODUCTIONThe concept of re-using foundations is not new, and has been adopted on an isolated project-byproject basis for many years. However, over the past decade, interest in the potential of reusing existing piles and caissons within Europe has increased significantly, with a growing interest in the United States of America and Japan. The need has been driven by necessity: on many urban sites the space available for new foundations diminishes with each new set of piles, and these problems can only grow in the future.Initiatives such as the European Union's RuFUS (Re-use of Foundations for Urban Sites) research project have resulted in identification of the key issues for technical viability and risk that have previously hampered potential foundation reuse projects.There is a need to define a systematic approach to the reuse of foundations so that the risks associated with reuse can be identified, managed and mitigated. This requires improvements in knowledge to provide confidence in the long term behaviour of the foundation support and address the risks involved in reusing existing foundations to overcome perceived obstacles in making foundation reuse a realistic option for many sites."

Jan 1, 2005

By Jom Gentry

Acrylamide chemical grout (C3H2NO) has been successfully used for over 50 years to control groundwater and stop infiltration. This paper will address three unique projects involving the control of groundwater with each study providing special circumstances and geological conditions: encapsulation of radioactive hazardous waste in the United States, a tailings dam for a large copper/gold mine in Argentina and 27 miles of leaking subway in Canada. The primary reasons for selecting acrylamide grout were based on the following characteristics: thinnest chemical grout on the market, a true solution grout which contains no suspended solids in the blended product, flexible gel set times, and a 362 year half-life in soil as determined by the U.S. Department of Energy.

By C. L. Liao

The chief experiences for constructing deep tubular columns foundation under deep water are as follows: 1. P.C. tubular columns were sunk inside the caisson. 2. P.O. tubular columns of 3.6 M. diameter were sunk thru thick soil layer to a depth of 47 M. by vibrators. 3. The double wall steel cofferdam was sunk thru soil layer to a depth 31.3 M.. 4. Bore the bedrock with rotary drill succesfully. According to the successful experiences mentioned above, the deep tubular columns foundation may be constructed beyond 100 meters.

Jan 1, 2010

By A. Verghese Chummar

The paper presents a field study where the effect of negative drag caused the failure of a pile foundation system. Utilising the field observations the probable negative drag that acted on the piles is worked which gives an insight into the effect of negative drag on deep foundations.

Jan 1, 1996

By Helen D. Robinson

Traditional practice to resist large lateral loads on foundations is the use of large diameter caissons, battered driven piles, or battered micropiles. Dense urban construction environments, however, limit the usefulness of these systems due to the close proximity of below- and above-grade obstructions. This paper presents two micropile construction projects in the United States where a complex scheme of battered micropiles and grade beams was developed to counteract large lateral loads at the foundation level. The paper also presents a procedure used to design vertical micropiles for large lateral loads, which can greatly simplify the design of foundations subject to significant lateral loads in urban environments. A design example shows a case where vertical micropiles were used to support allowable design lateral loads greater than 80 kip per micropile.

Jan 1, 2010

By Patrick P. A. Wolfs

In the summer of 2000, the ECR®/EFT® was first introduced in the Netherlands. After the first project a field test was performed together with other geophysical methods to prove the liability of these systems and their application in areas with soft soil and high groundwater levels. The objective of this test, which was carried out with three leakage detection systems, was to locate the holes. After this test several projects have been carried out. In this article the Dutch projects "Ringvaart Aqueduct" and "Bottleneck Limburg N296/N297" are mentioned.

Jan 1, 2006

By Harry K. Weatherbee

The paper presents a design case study for a four-story correction facility addition in south Boston, Massachusetts, supported on friction piles driven into the Boston Blue Clay. 356 mm (14-in.) square prestressed-precast (PSPC) concrete piles were selected as they were found more effective and economical. A static load test was performed where the pile was brought to "failure". The load test data were evaluated to estimate the Ultimate Pile Capacity as well as the Ultimate Unit Skin Friction (Adhesion) to serve as a design tool for friction pile projects in the south Boston Area.

Jan 1, 2003

By SungWon Park

The efficiency of the current design methods for computing pile resistances is evaluated using field load-settlement tests results. Twelve load-settlement test data for drilled shafts and bored piles were obtained from the literature. These load-test data were fitted using the ?t-z? method. Subsequently, the ultimate resistances were evaluated based upon the failure criteria from following methods: (1) the Davisson?s approach and (2) settlement corresponding to 5% or 10% shaft diameter approach. The ultimate resistances for these drilled shafts and bored piles were also predicted using methods based on the design code from North America (United States, Canada), Europe, and Asia (Japan). The pile resistances determined from field load-settlement tests were compared with those calculated using the design codes. The comparisons show that most design codes predict a conservative resistance for drilled shafts and bored piles. However, in the case of drilled shafts, we find that some of the design codes can over-predict the resistance and, therefore, should be applied cautiously. This research also shows that ?t-z? method can be successfully used to predict the ultimate resistance and the load transfer mechanism for a single pile.

Jan 1, 2009