Search Documents

By Anil Bhandari

Using subsurface data collected at each drilled shaft location is an ideal approach for conducting drilled shaft design. However, conducting subsurface tests at each drilled shaft location and subsequently performing the drilled shaft design can be a daunting task for a noise barrier wall that is divided into six (6) sections and stretches for approximately four (4) miles. In addition, having individual drilled shaft designs complicates the construction process. Grouping the subsurface conditions into broad categories and performing the design for each of those categories is an attractive alternative to the design per boring approach. Currently there are no existing guidelines to aid a designer on grouping the subsurface conditions for the drilled shaft design for the noise barrier walls. Therefore, a method was developed based on the Standard Penetration Test (SPT) N values of the near surface soils to categorize the soil profiles into distinct categories. Since the soil engineering properties of the near surface soils are known to be critical for drilled shaft lateral capacity, these soils were emphasized in the methodology. This method was successfully implemented for the design of drilled shafts supporting the noise barrier walls along the I-20 in Columbia, SC. For this project, two distinct soil profiles, labeled as ?strong? and ?weak?, were used. An overview of the soil profile grouping methodology is presented as well as the vertical and lateral drilled shaft capacity analyses for this project for the two general soil profiles. The analyses indicated that the axial capacity governed the design in the ?weak? soil profile and the lateral capacity controlled the design in the ?strong? soil profile. However, this is not a generalization and whether the axial or the lateral capacity governs the design of drilled shaft depends on the soil profile and design loads. Nonetheless, our findings emphasize that both lateral and axial capacity should be checked for drilled shaft design even when the vertical load are minor.

Jan 1, 2011

By Matteo Montesi

Deep foundation elements are often used as discrete elements in externally supported earth retaining structures such as soldier piles and lagging walls, secant/tangent pile walls, anchored walls, etc. These structures can be designed using different approaches such as conventional limit equilibrium methods, finite element/difference analyses, and soil spring (p-y) analyses which are contained in various commercially available computer programs used by engineers worldwide. Although these programs usually undergo various degree of verification and validation, users must be aware of each program’s limitations and conditions in which each design approach should or should not be used. These programs may incur difficulties when non-continuous deep foundation elements are used as part of the retaining system and in cases of non-uniform geometry where closed-form solutions are not available. Design input parameters such as passive arching width, wall-to-soil friction, and p-multipliers (pm) are not always given enough attention which may result in potential design deficiencies. This paper presents the main features of various earth retaining structure design approaches and discusses their advantages/disadvantages. The paper addresses some of the limitations and difficulties that may be faced with when utilizing non-continuous discrete deep foundation elements and identifies key elements that are sources of potential deficiencies and errors. An example comparing the design outcomes using different design approaches is presented. INTRODUCTION Earth retaining structures are used to retain soil and create or maintain a difference in ground elevation between grades in front and behind the retaining structure. Deep foundation elements have been used for decades to support earth retaining structures. Earth retaining structures that are supported by deep foundation elements are typically referred to as externally stabilized system (O’Rourke and Jones, 1990). An externally stabilized system uses an external structural element, in contrast to internally stabilized systems which rely on reinforcements installed within and extending beyond the potential failure mass. The design of externally supported retaining structures can be accomplished using different approaches, which can be challenging under certain conditions. Each approach has been discussed extensively in available literature, and is well summarized in the and Federal Highway Administration (FHWA) guidelines. The objective of this paper is to present the most widely used design approaches and discuss their limitations and difficulties in one concise and brief document, giving the reader a good source for comprehensive understanding of the various design approaches, supported by a technical example. This paper is not intended to be a comprehensive review of all available design methods and formulations available in the literature.

Jan 1, 2018

By O&apos, M. W. Neill

Mini-piles have been found to be a practical, technically correct remedial underpinning method. They can be constructed in limited access areas with very little disruption. Experience indicated that mini-piles installed using a down-the-hole soil displacement hammer would be particularly effective in the "bottomless" Beaumont Clay formations in the Houston, Texas, U.S.A. area. The University of Houston Foundation Testing Facility was ideally suited to perform tests on mini-piles. The availability of extensive geotechnical data and previous pile test results was invaluable in evaluating the mini-pile test data. As expected, the mini-pile test results were consistant with test results from large sized driven piles in the same soil formation.

Jan 1, 1989

By Michel Bustamante

The occasional substandard performances of continuous flight auger in particular soil conditions have prompted the drilling rig manufacturer to improve the standard CFA in order to reduce its negative effects. A real improvement of interest was the launching of the double rotary CFA system. The promising features of the latter have incited the authors to implement an extensive experimental research on pile constructed using this type of technique but in the specific context of cohesive soils. Short-term static load tests were carried out on a total of 9 test piles of various installation techniques in order to compare the respective performances. The promising features of the double rotary CFA have incited the LCPC & Durmeyer Company to implement an extensive experimental research on this type of pile technique but in the specific context of cohesive soils and more particularly in clayey marls. After load tests completion the research has been completed by an excavation of the double rotary CFA piles. All the collected data concerning the implemented program are reported.

Jan 1, 2002

By Masaki Kitazume, Yoshiaki Kikuchi

"Abstract Pile foundation is one of fundamental techniques to improve the bearing capacity and settlement characteristics of superstructures. Wide varieties of piles having various shape, size and material were developed and have been applied to a lot of construction projects throughout the world. The deep mixing method, an in-situ admixture stabilization method, was developed in 1970s in Japan and the European countries, and has been frequently applied to many construction projects for various improvement purposes such as increasing bearing capacity and horizontal resistance, reducing ground settlement, preventing liquefaction and so on. The design methods, execution procedure and quality control and assurance (QC/QA) of the method are standardized or specified in many countries. These standards, specification and/or technical manual have been a remarkable contribution to spread the techniques throughout the world. The QC/QA is one of the major concerns for clients and engineers who have poor or no experience of the technologies. In order to assure the high quality of deep mixing work in the global market, it is necessary to establish the concept of QC/QA and correlate the output of different procedures. Upon the request by the organizing committee of the DFI-EFFC International Conference on Piling & Deep Foundations, the authors conducted survey of the specifications and standards on the piling and deep mixing technologies in Asian countries. In this manuscript, the results of survey are briefly introduced by comparing these specifications and standards.IntroductionThe pile foundation is one of fundamental techniques to improve the bearing capacity and settlement characteristics of superstructures. Wide varieties of piles having various shape, size and material were developed and have been applied to a lot of construction projects throughout the world. The design method, execution procedure and quality control and assurance of pile foundations are standardized in many countries based on the accumulate research results, laboratory and field experiences. In Japan, steel pipe piles are mainly constructed by hammer driven in port construction. On the other hand, precast pre-stressed concrete piles or cast-in-place piles are mainly used in on land construction. When precast pre-stressed concrete piles are constructed, piles are usually set by inner excavation method because of preventing noise and vibration problems. More than 50 years ago, noise and vibration problems had not been serious problem in Japan, but around 50 years ago, they became serious and now less noise and vibration construction methods are used for pile construction on land in Japan. In Asian countries, though piles used for construction have a lot of variety, precast pre-stressed piles are commonly used. In this report, execution controls of construction methods of steel pipe piles and precast concrete piles are mainly considered."

Jan 1, 2014

By Sanket Rawat, Ravi Kant Mittal, Vikash Prasad

"The understanding of the response of pile foundations under various types of loads is a necessary prerequisite to analyze and design them properly. Therefore, this paper highlights and compares the provisions available in Indian Standard IS 2911:2010 to estimate the capacity of laterally loaded pile foundation with the provisions available in different country codes and existing literature. Comparisons are made between the Indian standard method, Broms method and Matlock & Reese method for the analysis of laterally loaded piles due to popularity and prevalence of the later methods in design offices worldwide. This has been achieved using a parametric study on pile embedded in pre-consolidated clay and sand for both fixed head and free head case in terms of displacement and ultimate load capacity. It has been found that there are various limitations to the Indian Standard method associated with various cases such as short pile analysis, complete moment distribution etc. Therefore, suitable recommendations have been made on the basis of the above comparison to improve the accuracy of the design in Indian perspective. The proposed comparison and subsequent area of improvements will present the design engineers all across the globe, a broad sight of design specifications of laterally loaded piles.INTRODUCTIONPiles in groups are very often subjected to both axial and lateral loads. In the 1960’s, designers used to assume that the piles could carry only axial loads and the lateral load is to be carried by batter piles. However, later, a large number of load tests authenticated that vertical piles also can transfer lateral loads through shear, bending, and lateral soil resistance rather than purely acting as axially loaded members. Initial attempts to analyze laterally loaded piles used the finite-difference method, as described by Howe (1955), Matlock and Reese (1960), and Bowles (1968). Matlock and Reese (1956) used the finite difference method to get a series of non-dimensional curves to enable the user to input the appropriate curve with the given lateral load and estimate the ground-line deflection and maximum bending moment in the pile shaft. Later, Matlock and Reese (1960) extended the earlier curves to include selected variations of soil modulus with depth."

Jan 1, 2017

By Hanlong Liu

The construction process and load-bearing behaviors of Cast-in-place Concrete Thin-wall Pipe Piles are analyzed based on its application on Yan-Tong Expressway project. The low strain test, static load test and field excavation are also carried out. It can be concluded that the new type of pile is convenient to construction with high bearing capacity and reliable quality, which has great potential in practical engineering.

Jan 1, 2006

By Trevor L. L. Orr

"AbstractThe background to the harmonization of geotechnical standards that has taken place in recent years in Europe has been the move to more economic and political integration following World War II that has led to the formation of the European Union. Prior to 2010 the standards used in the European countries for geotechnical design, investigation and testing and for the carrying out geotechnical work, such as the installation of piles, were the different national standards, which were not harmonized. The harmonization of geotechnical standards in Europe started in 1981 with work on a model Eurocode 7 for geotechnical design that led eventually to publication by CEN, the European Committee for Standardization, of the European Standard version of Eurocode 7 in 2004. In parallel with the work on Eurocode 7, a large number of associated harmonized standards have been, and are being, prepared by CEN and by the International Standards Organization (ISO) for geotechnical investigation and testing and for the execution of geotechnical works. Standards published by CEN must be adopted by the CEN member countries and all conflicting standards withdrawn. Hence all the CEN countries have adopted the same the harmonized text of Eurocode 7, but with National Annexes that allow national choice with regard to Design Approach and partial factor values. The adoption of Eurocode 7 and its associated geotechnical standards has removed the barriers to geotechnical activity in Europe due to the presence of different national standards. It has also enhanced the ability of EU firms to compete in the global market.Background to harmonization of geotechnical standards in EuropeThe initial moves towards the harmonization of geotechnical standards in Europe can be related to the economic and political developments that took place in the period immediately following World War II to revive the economies of Western Europe. Europe at that time was divided by a political and, in many places, a physical barrier, known as the Iron Curtain, into two very different and separate zones: communist in the east and non-communist in the west. In 1952 the European Coal and Steel Community (ECSC) was formed, linking 6 countries: Belgium, West Germany, France, Italy, Luxembourg and the Netherlands, and establishing a common market in coal and steel. The ECSC was the first international organization to be established on the basis of supranational principles whereby negotiated power is delegated to an authority by the governments of the member states. In 1957 the ECSC became the European Economic Community (EEC), also known as the Common Market in the English-speaking world, with the aim to bring about economic integration. With the addition of Denmark, Ireland and the UK in 1973 and Greece in 1981, followed by Portugal and Spain in 1986, this led to the formation of the European Union (EU) in 1993. East and West Germany were reunified in 1990, following the fall of the Iron Curtain in 1989. In 1995, Austria, Finland and Sweden joined the EU, and since then the numbers of countries in the EU has increased to 28, many of which are countries that were formerly behind the Iron Curtain."

Jan 1, 2014

By Karl A. Higgins

In 1976, Prof. G. G. Meyerhof published a famous article in the Journal of Geotechnical Engineering titled ?Bearing Capacity and Settlement of Pile Foundations?. This article presents the authors opinions on calculating pile capacities in clays and sands, group capacities and pile settlement. A portion of the article presents correlations of shaft friction and end bearing to the Standard Penetration Test (SPT) N-value. Subsurface exploration via the Standard Penetration Test is the most widely used exploration tool in the United States, so correlations of pile capacity to N-value are significant to the practice of geotechnical engineering. Meyerhof?s SPT-N correlations are relatively simple calculations compared to other pile capacity computation methods presented in the article or found in other text books (such as the a-method, b-method, Nordlund, Vesic, Meyerhof?s semi-empirical, others) and therefore are popular amongst practicing geotechnical engineers. At the time these correlations were published by Prof. Meyerhof, utilization of dynamic testing with the Pile Driving Analyzer (PDA) was not widespread in geotechnical engineering practice. Prof. Meyerhof?s correlations appear to be based upon conventional static pile load testing of instrumented piles. Dynamic pile measurements to estimate a pile?s static capacity provides certain advantages over conventional static load testing, namely the determination of unit shaft friction values at discrete intervals along the pile, and the unit end bearing support value. The author has compiled a database of driven, displacement piles tested with dynamic methods (ref. ASTM D4945, Test Method for High-Strain Dynamic Testing of Piles). The data was collected between 2002-2010 and is comprised of displacement piles driven into coastal plain sediments in the mid-Atlantic states of Virginia, Maryland and the District of Columbia. In layered soils, dynamic testing in particularly helpful as it reveals the differences in unit shaft friction for varying soil types. One hundred ninety (190) piles are included in the database, with a corresponding 1,373 discrete shaft friction and 190 end (toe) bearing measurements. The pile type typically consisted of 12 and 14 inch square, prestressed, precast concrete piles; however, a significant number of piles were steel HP 12 or 14 inch sections. The database was sorted based upon soil type, and then correlations of shaft friction and end bearing were derived in the same or similar manner as Meyerhof?s original 1976 publication. The new correlations are compared to Meyerhof?s original values.

Jan 1, 2011

By Swaminathan Srinivasan, Jess A. Schroeder

"Landslide activity along U.S. 50 in Cincinnati, Ohio (USA) has caused roadway damage for decades. After a necessary closure of three lanes due to slope movements, emergency stabilization measures were undertaken to protect the roadway by providing a short-term solution necessitated by The Ohio Department of Transportation budget constraints. The landslide shear plane occurred on a sloping bedrock surface as much as 50 feet below grade. Drilled shafts were installed 40 feet downslope of the roadway shoulder and were heavily reinforced across the shear plane but steel reinforcing did not extend the full length of the shafts and was stopped well short of the ground surface. Instrumentation data has been collected for 11 years after construction has shown these “Stub Piers” have provided much more than a short-term solution and have provided an attractive alternate to conventional deep shafts or tieback drilled shaft options.INTRODUCTIONLandslide activity has occurred along U.S. Route 50 in western Cincinnati, Ohio for many decades. The site is located between North Bend and Addyston, Ohio on the right descending (cutting) bank of the Ohio River. Road distress caused by slope movements required periodic repairs over recent decades. Railroad tracks downslope of the roadway also showed signs of horizontal displacement and periodic repair. Visual evidence in 2005 suggested the shear plane extended below the US 50 roadway and extended out into the Ohio River.A weed and brush-covered slope extended down slope from the roadway at about 3H:1V for a vertical distance of about 20 feet. Above US 50, the hillside continued to rise more than 100 feet. There is a railroad right-of-way at the toe of the slope with the Ohio River bank just downslope of the railroad.In 2005, Terracon Consultants was retained by the Ohio Department of Transportation (ODOT) to perform a geotechnical study that included 17 test borings and inclinometer monitoring at 4 locations. Roadway damage was occurring (see Figure 1). After only a few weeks of monitoring, the inclinometer casings sheared off about 50 feet below grade, near the soil / bedrock interface (see Figure 2). Soon after, the roadway distress worsened, causing ODOT to close 3 of the 4 lanes to traffic and reroute traffic onto the remaining single lane and shoulder. Terracon was asked to develop a stabilization design under emergency repair conditions. However, both limited budget and time-related constraints necessitated a direction by ODOT that the solution be at least “pseudo” short-term (3 to 5 years)."

Jan 1, 2017

By S. Kanai

Nodular piles is to be piles provided with several nodular projections along the pile shaft, as shown in Fig. 1. Nodular piles are usually installed through either driving method with hammer or preboring method. This paper presents that the bearing capacity installed through each method is considerably higher than that of cylindrical pile without nodules. This paper also proposes the statistically analyzed unique formulae of the bearing capacity of nodular piles.

Jan 1, 1989

By Eric C. Halpin

"1. Introduction and Backgrounda. In its fundamental form, risk is simply the likelihood of an adverse impact. Expanding on this theme, the Corps of Engineers has broadly defined risk associated with infrastructure as a factor of three distinct elements: a probabilistic assessment of a hazard such as a flood or earthquake; a probabilistic assessment of how the infrastructure performs in the face of this hazard; and a measure of the likely consequences – loss of life, economic damage, environmental impacts – associated with the resulting inundation scenarios.b. The lessons and observations described herein relate to the Corps of Engineers experiences in implementing risk concepts for infrastructure management during the period 2005 through 2013. The Corps of Engineers is a large, decentrally operated and centrally led federal agency that plans, designs, constructs, operates, maintains, and/or manages a portfolio of over 3,000 built dam and levee systems within the United States. The infrastructure in this portfolio is 55 years old on average, and although much of the structures provide for flood risk management benefits, many of the dams deliver multi-purpose benefits. Scale matters – where scale and uncertainty are large, risk concepts provide great opportunity and arrangement for application.c. The amount of organizational change that is demanded for the implementation of risk concepts is considerable and should not be under estimated, but need not be feared if the path others have taken is considered. This paper is, in many ways, an opportunity to step back from the last seven years of implementing risk informed management, check our own azimuth and maturation, and share the purpose and energy behind our own continuing actions. Hopefully, this azimuth check is also beneficial to those that are either considering the use of risk or are in the process of implementing risk concepts.d. Success at managing the massive change related to incorporation of risk concepts will directly affect success of the infrastructure program. The three key organizational elements to consider –human systems such as governance and competencies; policies that outline the who, when, and why of decisions and management; and the processes and technology that outline how work is to be performed - are changed fundamentally. From senior leaders to project team members and all of the people in between, there is a need to discuss, confront, and vet the change and the role people and organizations have in the process. For the Corps of Engineers, with a history of over two centuries, deeply embedded beliefs about infrastructure aren’t transformed over night - the change process is decadal in scope. Given our self imposed “project execution” mantra and corporate objective, risk seemed threatening at first to the cost and schedule of delivering infrastructure projects. In reality, risk concepts have been responsible for savings and cost avoidance of nearly $6 billion over the last three years alone while at the same time justifying increased investment by several fold for the highest risk needs."

Jan 1, 2014

By Jean Balech

This paper presents some results of dynamic loading tests performed on concrete piles driven in soft clay formation. The load transfer mechanism, measured in the dynamic increasing energy test (DIET), under blows of growing energy, is described in terms of mobilized normal forces diagrams and unitary local friction and displacements. It was observed that the lateral skin friction grows up to a maximum, in the soft clay layer and, gradually diminishes to a residual value when the system presents the maximum mobilized resistance. It may be concluded that the rupture load is not equal to the maximum mobilized point resistance plus the maximum mobilized local friction as suggested by most of static bearing capacity formulae.

Jan 1, 2002

By Nuno Cruz

"The concrete overbreak estimation for bored piles provides the quantification of the shaft’s expansion beyond its theoretical volume. There are stability analysis methods that can be employed before and after concrete pour but as for the moment of decision, during pile cast, the most common method still consists in measuring the rising of the concrete level in order to compare its poured volume with the theoretical pile section volume. This is a determinant parameter to monitor, not only because it assesses the bored shaft stability but also because it represents a direct cost. When analyzing the estimation methods commonly applied on-site it becomes evident that these are often affected by human errors that lead to misleading results. The objective of this paper is to identify those errors and discuss a subject which is usually overlooked. As a general conclusion, it was ascertained that most errors derive from inaccurate volumetric data, working procedures and gauging equipment. By acknowledging these widespread practices deep foundations contractors will be in a better position to make informed decisions on how to correct and improve bored pile stability.GENERALBackgroundWhen executing bored piles, the estimation of its concrete overbreak allows a swift appraisal of the excavation stability during the drilling process. This is simply obtained from the proportion of the poured volume of concrete over the drilled shaft theoretical volume, as shown in equation [1].Where CO = concrete overbreak percentage, Vc = volume of poured concrete, Vr = pile’s theoretical volume. This calculation not only provides a general idea of the shaft’s expansion from its theoretical volume, but also the outline of the excavated column’s geometry. For the latter, the outline will be as accurate as the number of measurements taken for each partial known volume of poured concrete. This means that for each load placed inside the excavation there is a corresponding rising of the concrete level. The profile of the definite pile is then plotted (see Fig. 1) and allows inferring about how stable remained the shaft walls up to the moment of casting.The technological developments in this area have provided other methods for determining pile stability before and after pile cast, such as ultrasonic echo sensing, cross-hole sonic logging or thermal integrity profiling systems. Notwithstanding, concrete overbreak assessment remains as common practice and confers the advantage of providing stability information during the process of pile casting."

Jan 1, 2017

By Ramon Varghese, A. Boominathan, Subhadeep Banerjee

Pile raft foundation system has been accepted as an economic foundation design for high rises and heavily loaded structures. Seismic response analysis of PR foundation systems involves complex pile-soil-pile interaction as well as raft-soil-pile interactions, for which simplified methods have limitations. Kinematic rocking of a pile group is known to be influenced significantly by the pile configuration. The presence of an embedded pile cap, or a raft, as in the case of a piled raft can further alter the dynamic characteristics of a pile group-soil system. In the present study, frequency dependent kinematic response factors are evaluated for piled raft foundation, using the substructuring approach based ACS SASSI program. Performance of the numerical analysis methodology is first evaluated with results from analytical and experimental studies reported in literature. The effect of pile layout on kinematic response is then studied for a piled raft in clay system based on a centrifuge shaking table test reported in literature. Kinematic response factors and horizontal impedances were determined for varying pile spacing ratios. The influence of raft has been found to increase kinematic translation by up to three times in the piled raft in clay system. Pile configuration is found to play a significant role in kinematic rocking of piled rafts. The presence of raft is observed to significantly reduce dynamic rotational stiffness coefficient in the dimensionless frequency range of 0.23 to 0.6, and increase damping coefficient after a dimensionless frequency of 0.4, for all pile configurations studied. The effect of an embedded raft is hence an important consideration while evaluating foundation input motion as well as impedances of piled raft foundations. INTRODUCTION The Piled raft foundation (PR), is a composite foundation system that facilitates load sharing between pile and raft. It is an economic foundation option for high rises and heavily loaded structures. Soil structure interaction (SSI) in PR system involves raft-soil-pile, and pile-soil-pile interactions which needs to be considered in static or dynamic SSI analysis. The effect of pile can have substantial influence on foundation input motion, for seismic analysis (Di Laora et al. 2017). Piles are observed to depress a wide spectrum of the seismic excitation (Fan et al., 1991, Di Laora & de Sanctis, 2013). Although kinematic response of pile groups have been extensively studied in the past, the influence of the presence of raft on kinematic response characteristics of pile groups has not received much attention.

Jan 1, 2018

By R. J. Folic

Investigations of the vibrations of a pile in soil are performed on a dynamic model in the form of a prismatic bar of finite axial and flexural stifnesses with a discrete mass at its free end representing the cap. The soil is represented by a system of springs of constant and variable stiffnesses. Oscillation differential equations are derived by means of the Hamiltonian principle for non-conservative systems. The problem is reduced to a coupled system of two non-linear partial differential equations with corresponding initial-boundary conditions. Frequency equations of longitudinal and lateral linearized equations are formed. The paper determines natural frequenc­ies and oscillation modes. It separately examines longitudinal vibrations excitated by a hermonic force acting upon the pile cap, and lateral vibrations excitated by an impulse acting upon the cap. The results of the numerical processing are presented in respective diagrams in dimensionless form.

Jan 1, 2010

By Koichi Kobayashi

Performance-based approach to design of structures including foundations was adopted after enforcement of the revised Building Standard Law in Japan in 2000. The use of piled-raft foundation is favorable for medium-rise buildings in soft ground because of its good performance. In the design of the piled-raft foundation (Architectural Institute of JAPAN2002), vertical load is usually carried by the raft foundation, while the pile is primarily meant to control settlement of the structure. Shaft friction is expected to be larger in a nodular pile(Karkee, et.al., 1998) since it has larger surface area than a straight pile, and such piles are frequently used in piled-raft foundations. Since few structures with piled-raft foundation exist currently, the settlement characteristics of piled-raft foundation have not been fully clarified. To design piled-raft foundations with better confidence, the mechanism of vertical bearing capacity and the spatial distribution of settlement should be clarified, for which the actual behavior of the building-foundation system needs to be evaluated. This paper presents observations of settlement of a building with a piled-raft foundation at a soft ground site. The building is a steel structure covering an area an 766 m2, and consists of two-storey office block and one-storey warehouse block. The filled ground of about 5-m thickness at the ground surface is underlain by approximately 4-m thick alluvial sand layer below which lies about a 17-m thick alluvial clay layer with SPT N-value less than 2. The piles used in the piled-raft foundation are 12-m long nodular piles with nodal diameter of 500 mm (pile shaft diameter is 400 mm). The bored pre-cast piling method (Karkee, et.al., 1998) was used to install the piles. To evaluate the foundation settlement, the method of analysis of three-dimensional frame system, utilized widely in Japan, was adopted in combination with the foundation system. Basic assumptions were: (i) total ground settlement is evaluated as the sum of immediate settlement and consolidation settlement, (ii) immediate settlement is evaluated from the Mindlin?s solution in which strain dependency of shear modulus of soil is considered, (iii) settlement in clayey layers is evaluated by the one-dimensional consolidation theory, and (iv) shear spring between soil and pile shaft is represented by a hyperbolic function. The applicability of the method of analysis was verified by comparison with results of field monitoring of building settlement.

Jan 1, 2006

By Danielle Nhanqulumanga, Pranith Bhatt, Snehal Patel, Khadeeja Priyan

The Bi-Directional Static Load Test (BDSLT) is a test that determines the capacity of piles when loaded under bi-axial static compression. In recent years the BDSLT has seen an increase in demand due to its safety, speed, and affordability. This innovative foundation testing method has been universally used over the last 50 years, however respective codes and standards have only been published within the recent years. Detailed test procedures and methodology are expatiated in the ASTM D8169 M-18 [1], and the IRC 78 2014 Clause 709.2.5. [2] These standards provide the minimum requirements for the execution of the BDSLT. In this paper we did a comparative study of both standards envisaging to bring attention to the similarities and discrepancies found therein, with an aim to highlight the impacts and challenges that differing provisions of each standard could pose on the conduct of the BDSLT. Discrepancies found have been explained on the basis of geotechnical engineering theories and relevant field occurrences observed by superior engineers. Additionally, we emphasize on the relevance of experienced engineer’s judgement when utilizing the standards.

Sep 1, 2022

By Enrique Ibarra, Manuel J. Mendoza

"Abstract: This paper describes the current state-of-practice for the design of cast-in-place drilled shafts in granular soils under axial loading, addressing recent advances that take into account the surrounding soil grain size distribution and their behavior. The important role of the gravel content in the shaft response under axial loading is emphasized. Usual design approaches in Mexico are described, and the results of load tests from different sources are discussed. The analysis emphasizes the primary contribution of the lateral area of shafts to their axial bearing capacity, raising doubts regarding the common local idea of “point bearing shafts”. Finally, some lines of research are noted to permit advances in the important field of deep foundations. 1 INTRODUCTIONIn Mexico, cast-in-place drilled shaft foundations are widely used to support various structures in the west area of Mexico City, where alluvial and volcanic deposits predominate. Deep foundations are also used in modern construction works located in other major cities of Mexico. In fact, the use of drilled shafts for tall buildings and overpasses in the center of Guadalajara as well as in transportation works related to the Metro and roadways in Monterrey is well known. It is worth mentioning that these same structures have been applied in road bridges throughout the country.Procedures for pile construction in Mexico have been basically the same for the past 20 years (Paniagua et al., 2005); however, modern equipment has been incorporated into the construction industry, including innovations in sludge-drilling technology, control and the quality of the castings. In addition, novel and efficient procedures such as construction with continuous auger displacement piles have been implemented (Auger Cast in Place, ACP) and have begun to be used locally with success (Schmitter and Paulin, 2006).However, it can be argued that the technological developments that have resulted in more efficient construction procedures have not included a breakthrough in the full understanding of the phenomena or basic mechanisms of load transfer from piles to the surrounding subsoil and therefore in supported, tested and practical design methods. This is particularly true when seeking to determine the unit side shear strength of shafts drilled in granular media with gravels, where it has been observed that the commonly used calculations developed for sands underestimate the load-bearing capacity by frictionin a most important way. Due to the above reasons, it seemed appropriate to present in this paper a review of the current stateof- practice in Mexico for the design of cast-in-place drilled shafts, particularly in granular media, highlighting some recent advances and research that takes into account the grain size distribution and behavior of granular soil."

Jan 1, 2014

By Ryan T. Smith, Anthony Sahj, Alexander T. Darnell

Every second can count when trying to board a departing flight or catch a ride-share to your final destination. Hartsfield-Jackson Atlanta International Airport is in the midst of a project that aims to cut about 13 seconds between automated people mover trains (Plane Train) that move passengers between the terminals and concourses. The project involves extending the Plane Train tunnel west from its existing terminus under the domestic terminal. Working from inside non-public areas of the terminal, Keller North America, Inc. (Keller) incorporated systems of micropile-supported steel beams and grillage to both underpin existing columns prior to tunneling and support open-cut excavation at the tie-in of the new to the existing tunnel. Dewatering aided in mining a challenging section at the start of the drive of the mixedface, sequentially excavated tunnel and an automated instrumentation system monitored the performance of the construction and its impact to the terminal. Cut and cover egress and ventilation tunnels required braced support of excavation.

Oct 1, 2022