Search Documents

By Prasanta Paul, Aminul Islam

"Nhava Sheva (India) Gateway Terminal Private Limited proposed to construct a container terminal yard, comprising a back-up area at Jawaharlal Nehru Port Terminal (JNPT), Uran, Maharashtra. The proposed container terminal yard is located on a recent reclamation on the Thane Creek, which was developed by land-based reclamation method. The underneath soft marine clay was treated, using vertical band drains and placement of surcharge upon.Settlement of the reclamation during its construction was monitored using settlement plate installed at +4.8m CD elevation which was above the highest high water level.This paper examines the settlement behaviour of the reclamation during the ground improvement works. The geotechnical parameters are back-analyzed by the authors from the field settlement results and the concerned preloading details. The back analyzed coefficients of consolidation due to horizontal flow (Ch) are compared with laboratory determined parameters and the estimated value, using Asaoka Method (1978). The authors also studied field compression ratio [CR= Cc/(1+e0)] vs. the compression ratio determined by laboratory test using back-analysis method.1. INTRODUCTIONNhava Sheva (India) Gateway Terminal Private Limited proposed to construct a container terminal yard, comprising a back-up area of approximately 27 hectares, complete with associated buildings and services on a part brownfield/ greenfield site. The back-up area shall include a heavy duty block paved pavement with band beams for electric Rubber-Tyred Gantry Crane (eRTGC) alongwith surface water drainage system and other services including area lighting, provision of fire-fighting facilities , sources for potable water and power.Based on the Employer’s Requirement and the available geotechnical investigation report, ground improvement scheme is designed by the construction contractor. Ground improvement works included the installation of prefabricated vertical drains and subsequent placement of surcharge for accelerating the consolidation of the underlying soft marine clay."

Jan 1, 2015

By Arash Saeidi Rashk Olia, Dunja Perić

The increasing demand for renewable energy has attracted attention to energy geostructures as means of extracting clean geothermal energy from the ground. To further advance the understanding of soilstructure interaction in energy piles analytical solutions considering the self-weight of the pile were derived. These solutions were then incorporated in recently-derived thermomechanical weightless solutions to provide comprehensive analytical solutions for axial displacement, strain and stress in single energy piles. This was accomplished by comparing responses of energy pile under different loading scenarios that reflect presence and absence of the self-weight. Results of mechanics-based analysis revealed that the self-weight of energy piles embedded in stiff soils has no significant contribution to displacement, strain and stress that develop under thermo-mechanical loads. Overall, the significance of the self-weight contribution depends on the magnitude of thermal load as well as the soil-pile interface stiffness. The stiffness of end restraints imposed to the pile head and tip were also found to play an important role in contribution of self-weight in induced thermomechanical stresses in energy piles.

Oct 1, 2022

By Sunil S. Basarkar, Vinothkumar S

Ground Improvement Techniques serves to improve various engineering properties for supporting various foundations. These may be undertaken either by conventional or advanced methods. The Controlled Modulus Column (CMC), also known as Rigid Inclusion is a soil improvement technique to reduce the total and differential settlement by using semi-rigid soil reinforcement columns. The CMC technique can be executed by displacement or non-displacement methods. It does not aim to bypass the compressive layer or to install a pile that will directly support the entire load from the structure. Principle of the technique is to introduce a load transfer platform between the head of the column and structure and transform a uniform load into soil. Initially, the structural load transmitted into the soil generate the settlement greater than CMC piles. When the settlement between the soil and column became equal at neutral point, maximum structural load shall be balanced by the positive friction and tip resistance to stabilize the foundation without exceeding the allowable settlement limit. This paper describes the behaviour of soil reinforcement with CMC column and their installation process with reference to a project at the Dry Bulk Terminal Port, San Pedro- Abidjan (Western Africa). Methodology of CMC, requirements of Ground Improvement, arrangements and outcome of this method are presented in this paper.

Sep 1, 2022

By Ali Nasirian Ph. D., Gabriel Carvajal

To facilitate the safer and more secure transportation of inmates from San Diego Central Jail to the new San Diego Courthouse, the County of San Diego committed to building a new transfer facility as part of the downtown developments. The transfer facility includes a three-story underground structure adjacent and connected to the Central Jail and a 60-ft deep, 23-ft diameter, 320-ft long tunnel. The tunnel starts at County Jail, passes underneath Western Regional Detention Facility (Old Jail) and, ultimately, connects to the State Courthouse. Condon-Johnson & Associates, Inc. (CJA) was selected to install the temporary shoring shaft for the underground structure as well as three arrays of canopy pipes to support the tunnel’s Sequential Excavation Method (SEM) construction. CJA installed the rectangular 56-ft deep access shaft shoring with three levels of bracing, and a combination of secant piles, soldier piles, and timber lagging. The shoring also included a sliding bridge at top to provide access for trucks to enter and exit from county jail during the duration of construction. Following shoring and shaft excavation, CJA installed and grouted 7-5/8” dia. canopy pipes in 3 reaches, parallel to the longitudinal design line of tunnel with a slight lookout angle. CJA installed 24 each canopy pipes, 99-ft from face of shaft at reach 1, 21 each, 80-ft length canopy pipes at reach 2, and 21 each, 75-ft length pipes at reach 3. CJA confirmed canopy pipe alignment via Inertial Sensing Gyro. To mitigate the possibility of settlements caused by the tunneling operation underneath Old Jail strip footing and grade beams, CJA also performed void fill grouting. Sleeve port grout pipes (SPGP’s) were installed inside the Old Jail basement and grouted with the use of packers as the tunneling operation passed underneath the Old Jail. In detailing various aspects of the construction, this paper aims to magnify the innovative solutions for shoring, canopy pipe installation and void fill grouting challenges as well as the state of the art quality control measures undertaken by CJA.

Oct 1, 2022

By Babak Mamaqani, Pirooz Barar

The Moanalua trestle spanned over Moanalua Stream, Honolulu, HI and was designed to accommodate construction of five 10 feet diameter cast in drilled hole (CIDH) piers as a part of Honolulu Authority for Rapid Transportation (HART) project. Due to the proximity of piers to the existing bridge, the trestle was elevated 20 feet above grade. Stratigraphy of the site consisted of shallow depth of fill and 150 feet of loose to very loose recent alluvium (soft clay) underlain with stiff to hard old alluvium (stiff clay). CIDH casings were installed by a rotator or oscillator depending on the diameter of the piers. The challenge was to design the trestle, not only for heavy gravity loads, but also to resist significant lateral loads from rotator and oscillator with minimal deflection. Series of piles, called reaction piles, were integrated into the trestle at each CIDH pier location to provide adequate lateral support for the rotator/oscillator. Due to the lack of information regarding soil Young’s modulus (E), a methodology was developed to calibrate and calculate E with two methods. Extensive analyses using LPILE and finite element analysis program, PLAXIS, were performed to model reaction piles and calculate lateral deflection. PROJECT SPECIFICATIONS The Honolulu Rail Transit includes 20-mile route and 21 stations to be built from East Kapolei to Ala Moana Center, with $1.55 billion construction budget. The project is divided into two phases as shown in Fig. 1: Phase 1 which connects East Kapolei to Aloha Stadium with expected operation in late 2020, and Phase 2 which connects Aloha Stadium to Ala Moana Center with expected operation in 2025.

Jan 1, 2019

By Julie Clarke

In 1939 Dr. Ralph Peck criticized the Civil Engineering community for taking a bifurcated approach to the prediction of building damage due to subsurface geo-technical works. Specifically, he observed that Geotechnical Engineers concerned themselves only with subsurface issues implying that their results were largely independent of the presence and condition of the structures above. He continued that Structural Engineers charged with risk assessment of buildings approached their work nearly in isolation of below ground activities. Seventy years later, although the state-of-the-art has enabled a better understanding of soil-structure interaction, the reality remains that risk assessment from subsurface construction, is not yet an integrated activity when done on a large-scale basis. To help move beyond this, this paper proposes a new, integrated methodology for preliminary assessment that considers a three-stage process that involves the following: (1) traditional empirical relationships for predicting ground movement from tunneling, (2) recent advances in condition assessments, and (3) architectural designators related to usage and historic preservation listings. The methodology is applied to a study area of nearly 260 buildings in the city center of Dublin Ireland, in an area slated for an upcoming metro. The results are com-pared to the Environmental Impact Statement issued for the official project. Al-though the test case is for tunneling, the approach may be adapted to other subsurface construction activities including excavation and piling.

Jan 1, 2009

By Frank J. Purcell

“Down The Hole” (DTH) hammer drilling is often necessary to advance the casing during pile construction where the test bores have determined difficult drilling conditions with obstructions such as boulders, cobble and glacial till. The use of compressed air to operate DTH hammers in foundation drilling has been a contentious point in many regions of the world due to its potential to disturb the ground around the pile being constructed. There are many examples of damage to adjacent building foundations where compressed air exiting the pile being drilled disturbed the subsurface around the building’s existing piles. This paper looks at the use of compressed air in DTH hammer foundation drilling and the move towards controlling the exhausted air to avoid over drilling the pile, causing potential damage to nearby piles. Simulated models of air flow penetration into the soil of different configurations of drill bits are discussed to highlight design changes employed to better control the air during the drilling process. A case study of the construction of a water-tight pipe pile wall for a building’s underground parking structure is studied to demonstrate the potential of DTH hammer foundation drilling where the air is fully controlled.

Nov 1, 2022

By Tomio Tsuchiya

A construction method of bored steel H piles enclosed in soil-cement columns was developed by modifying steel H piles from the driven pile method and soil-cement walls from the earth retaining wall method, the latter of which produces cut-off walls and reduces noise and vibration during construction. In this method, as shown in Figure 1, rich mix cement paste is injected into the bottom of a borehole which is pre-excavated by a casing auger, then a steel H beam is inserted before it hardens. Since the high vertical resistance of piles created with this method has already been confirmed by loading tests, we have been investigating the applicability of this method for piles used to temporarily support building loads for top-down construction on raft foundations until the raft foundation is completed. However, in the loading tests, the bearing capacity at the lower end of the pile was measured by loading from ground surface on test piles which had friction cut to eliminate the shaft friction resistance. In other words, the loading tests neglected the effect of overburden pressure of soil above the lower end of the pile. To investigate the effect of the overburden pressure on the bearing capacity at the lower end of the pile, loading tests were carried out on a bored steel H pile of lm diameter (test pile) bored in a compacted sandy soil layer with N-value of 100 to 250 at each stage of a three-step excavation. The results show no significant change in the bearing capacity at the lower end of the pile when the depth ratio of the pile is in the range of 5.7 to 22.7.

Jan 1, 1996

By Stefan Schwank, Alexander Blatt, Franz-Werner Gerressen

Diaphragm wall technique is usually used to install diaphragm walls, which are known as underground structural elements commonly used for retention systems and permanent foundation elements as well as deep groundwater barriers, named Cut-Off-Walls (COW). In this exploration project, the diaphragm wall equipment was used in the 2019 summer season to perform the first part of an exploration and bulk sampling program for a potential mine on the Star Kimberlite. Beside the idea of using the diaphragm wall technique as bulk sampling equipment, the sampling program required the adaption of equipment and tools for a depth capability never reached before by a trench cutter in any commercial application worldwide. The paper will explain the development of the sampling program as well as the challenges occurred with the local geology and the specific demands of the exploration and sampling program. It will also provide an overview of the lessons learned during the 2019 season and will give an outlook to the approaches of optimization for the second phase which will be carried out in 2020.

By Dan Brown

Improvements in construction equipment and techniques in recent years have made possible the use of drilled shaft foundations in diameters and lengths not previously considered practical or feasible. Many highway bridge and other structures are now routinely founded on drilled shafts which -are 8 to 12 feet in diameter and extending over 200 feet in depth below grade. There are unique challenges associated with constructing such large and deep cast-In-place foundations and engineers should be aware of the special needs associated with site investigation, construction specifications, material requirements, and quality assurance. This paper outlines a number of special considerations for these foundations, along with strategies that may be employed to improve the reliability and quality of large drilled shaft foundations.

May 11, 2007

By Melissa S. Beauregard, Randall A. Pietersen

This study focuses on quantifying the effects of water infiltration on a full-scale energy pile system’s ability to meet the thermal demand of an HVAC system. Theoretically, an energy pile system should increase its thermal capacity after a rain event due to increased moisture content creating an increase in thermal conductivity of the surrounding soil matrix. The United States Air Force Academy has an energy pile research site consisting of 8 full-scale energy piles located below a shower facility. The local colluvium surrounding the piles allows for relatively high water infiltration during rain events. This study uses an 11kW Precision Geothermal Geocube to apply a thermal load on two single-loop piles. A weather station located south of the structure records atmospheric conditions. Results indicate that moderate rain events can caused up to a 23% increase in the system’s thermal exchange capacity. This change is due to the increase in moisture content near the surface, which penetrates to deeper soil layers with time. The time required for moisture to penetrate to greater depths and then dissipate in the soil matrix, explains why increased system performance is seen for over a week following the passing of a singular rain event. 1 INTRODUCTION With a “future-forward” focus, there is an ever-pressing economic and environmental need to use sustainable sources to meet growing energy needs. HVAC is typically responsible for 34% of the overall energy required by commercial buildings and 48% of the energy required by residential buildings (USEIA, 2009; USEIA, 2012). Energy piles are a low cost, sustainable technology that have been used to offset this energy demand incurred by a building’s space heating and air conditioning requirements. An energy pile consists of heat exchanging elements in a closed loop system integrated into a building foundation and connected to a ground source heat pump (GSHP). It is most common for these heat- exchanging elements to be constructed within a drilled shaft foundation due to both construction practices and geometric considerations. This system operates based on the principle that at a certain depth below ground (typically 4 meters) subterranean temperature remains constant at a value equal to the mean annual air temperature at a given location (Kavanaugh et al., 1997). This allows the soil to function as a heat sink for cooling operations and a heat source for heating operations when exchanged within this zone of relatively constant temperature. For the past 25 years, the implementation of energy pile technology in public, residential, and even large-scale architectural complexes has slowly expanded which has created an increase in research into the topic as a result (Brandl, 2006; Hamada, 2007; Sekine et al., 2007; Gao, 2008; Bourne-Webb, 2009; Stewart and McCartney, 2013; Murphy et al., 2014). When pile construction takes place beneath the groundwater table, soil is under fully saturated conditions, maximizing thermal exchange for a GSHP system. Under unsaturated conditions, however, changing moisture contents change thermal conductivity values in a soil, which affect a GSHP system’s ability to meet a thermal demand. The observational data presented in this paper apply to GSHP systems in unsaturated soil conditions.

Jan 1, 2019

By Sailesh S. Author

The current design method for soil-cement (SC) columns improved soft clayey ground under the highway embankments assumes a slip circle failure surface shearing through the columns and the soils using a weighted average shear strength. However, the results from the laboratory centrifuge model test and numerical analysis indicate that in many cases, the SC columns fail by bending. Some researchers have proposed methods for estimating the maximum embankment loading for bending failure of SC columns, but those methods have limitations in correctly considering the internal shear stresses or not applicable for the group SC column improvement. Numerous model embankments on SC columns have been simulated by three-dimensional (3D) finite element analysis (FEA) and the mechanism of bending failure and the magnitude of the bending moment in the SC columns under embankment load has been investigated. Based on the simulated results, the design method for the estimation of the bending failure of floating SC columns has been proposed. The predicted results from the proposed method agreed with the existing field condition of one embankment in Saga, Japan reported in the literature in terms of the stability of columns. Hence the proposed method can be used for the design of floating SC columns in the soft ground.

By Viswanadham B. V. S., Babu K. V

Many refineries are in the process of revamping and expanding their existing facilities. Most of the refineries are located in coastal areas due to ease of transportation and storage of crude oil. Considering the criticality of structures as well as prevailing soil conditions, most of the structures are supported on pile foundations. In depth review of sub-surface investigations data followed by liquefaction assessment of the site, it is noticed that site is prone to liquefaction during the seismic event. Among various techniques, driven cast-in-situ piles were selected to mitigate liquefaction. Static cone penetration tests were conducted during the pre and post installation of driven cast-in-situ piles at identified locations. Analysis of cone penetration test data shows that considerable ground improvement has been achieved post-installation of driven cast-in-situ piles.

Sep 1, 2022

By Michael Arnold

"BAUER Foundation Corp. was one of three contractors awarded with the installation of a cut-off wall at the Herbert Hoover Dike Rehabilitation project. The cut-off wall was constructed up to 84 feet deep and 25 inches thick. It extended from the crest through the middle of the existing dike into the underlying peat, sand, and rock layers. BAUER used the cement deep soil mixing method of Cutter Soil Mixing (CSM) to install the wall. Soil mixing was facilitated by first removing the peat layer in the wall alignment using Kelly drilling and replacing it with suitable backfill, resulting in a secant pile wall arrangement of replacement columns. BAUER successfully finished four task orders with a total length of just over 10 miles. Up to six rigs of the types BAUER BG 28, BAUER BG 40 and RTG RG 25 were concurrently used to perform the replacement columns and the cut-off wall installation.The paper introduces the project, the geotechnical site conditions, and the requirements specified by USACE. It focuses on the specific adaptation of the CSM method to the site conditions and on the equipment used. Strength and permeability results obtained from an extensive testing program are presented. The impact of the curing conditions on lab and in-situ test results is studied, and test results are related to soil conditions.PROJECTThe Herbert Hoover Dike is a 143-mile-long dike encircling Lake Okeechobee in south central Florida. When it was constructed in the 1930s and 1960s, the purpose of Herbert Hoover Dike was flood protection from hurricanes. However, during the 1970s a higher lake level was maintained permanently to provide local agriculture with water. Later, damage became apparent during two nearly back-to-back high water events in the 1990s, when numerous sink holes, seeps, pipes, and boils were observed (Fig. 1). In 2000, the Congress approved USACE to propose rehabilitation measures. The installation of a cut-off wall into the existing dike was chosen during the initial design process as the preferred measure to improve the safety of the dike (Davis et al. 2009).The first section of the dike to be rehabilitated was Reach 1 located along the southeast side of the lake between the towns of Port Mayaca and Belle Glade. An indefinite delivery indefinite quantity (IDIQ) multiple award task order contract (MATOC) was issued for this 22.4-mile-long stretch by USACE in 2007. BAUER Foundation Corp. (BAUER) was one of the three contractors that succeeded in the qualification process. Each of the three successful contractors had their own novel construction techniques. In the years 2008 to 2012 BAUER executed four task orders totaling over 10.0 lineal miles of cut-off wall with 3.3 million square feet of design surface area."

Jan 1, 2015

By Matthew E. Meyer

Renovation, rehabilitation, restoration and expansion of existing residential, retail, commercial, hospital facilities and historic structures requires assessment and evaluation of foundation systems of various ages. The concept of demolition and reconstruction in urban areas is often more challenging, costly, and even prohibitive in some cases due to historic regulations. The authors have been involved with numerous projects related to existing foundation assessment and retrofit, including: hotel and hospital expansions, historic Art-Deco hotel renovations and expansions, garage structure expansions, additions to prominent auction houses, casinos, printing facilities; high-rise structure foundation retrofitting; and forensic evaluations of existing building and highway structure foundation systems, and marine bulkhead sheeting systems. The use of non-destructive testing techniques, high-strain dynamic load testing, full scale pile cap load testing and 3-D laser scanning technology has proved to be vital in the assessment and evaluation process, as well as design of foundation retrofit alternatives. This paper presents various methods and techniques to facilitate a phased approach for re-use of foundation systems. These methods and techniques are illustrated through the author?s experience and selected case histories from projects with varied foundation and geologic conditions.

Jan 1, 2009

By Seth Robertson, Daniel Belardo, Travis Coleman

Thermal Integrity Profiling (TIP) is a non-destructive method used to evaluate drilled deep foundation integrity. This integrity testing method is specified more frequently, and is becoming an industry standard in the transportation and private construction sectors. This testing method utilizes heat generated during the concrete/grout curing process to assess deep foundation integrity over the evaluated length. With compilation of the measured temperature versus time and installation records, a model of the Effective Average Radius versus measurement depth is generated. The generated effective shaft model is highly dependent on specific construction details, subjective modeling parameters, and proper interpretation of concrete/soil heat dissipation characteristics. Key components of the TIP analysis include both qualitative and quantitative assessments. Qualitatively, variations or sharp reductions in temperature profiles may indicate potential anomalous regions. Quantitatively, a correlation is established between measured temperatures and estimated Effective Radii for subsequent integrity evaluation. Best practices in processing the TIP measurements are presented, including selecting the optimal time for analysis, normalizing the thermal profile, and proper interpretation of potential anomalous regions. Recommendations for implementing mitigation efforts and interpretation of the TIP results are presented.

Sep 8, 2021

By Joel L. Volterra

Since 1910, Mueser Rutledge Consulting Engineers (MRCE) has regularly provided professional engineering services including inspection of pile load tests. Historically, such services included on-site inspection of the driving of test piles and subsequent static load tests by qualified Geotechnical Engineers. Load testing procedures are specified by local or State Building Codes, locally the 1968 Building Code of the City of New York (1968 BCCNY). Between 1968 and 2008, the 1968 BCCNY required a minimum 48-hour hold period for standard loads per pile type, an extended 96-hour hold period for higher capacity piles, and a settlement criterion that the pile maintain a test load equal to two times the design load with less than 0.012 inches of settlement over the last 48 hours of the hold period. Effective July 2008, the new 2008 BCCNY shortened the hold period and relaxed the settlement criteria to that which is more similar to other governing codes and standards such as the International Building Code (IBC 2006) and the American Society for Testing and Materials (ASTM). MRCE implemented an automated load test monitoring system to reduce costs and to alleviate or minimize overnight and off-hour staffing for load test readings. Initially, a series of linear variable differential transformers (LVDTs) and data loggers were included in the Contractor?s load test setup to electronically record pile head settlement and where applicable, settlement of telltales installed to varying depths in the pile. A pressure gage was subsequently added in the hydraulic line, then a load cell, strain gages, and remote access using modems. The ease of the setup and modular adaptive nature of this system have proven it to be a useful tool and improved our ability to better serve our clients and manage our pile load testing services.

Jan 1, 2008

By Michael Perlow

Helical screw piles in use since 1838 are routinely used for energy, transportation, municipal, industrial, marine and coastal infrastructure as well as for excavation support, environmental remediation, and foundation repair. They are especially well suited for work in constrained areas, renovations and structure retrofits. Helical pile design procedures over the past 10 years have gone through a remarkable evolution with the establishment of the 2007 AC358 Helical Pile Acceptance Criteria and inclusion of helical screw piles in the 2009 International Building Code (IBC). New 2009 IBC building code requirements and AC358 Acceptance Criteria are presented along with advances in helical pile design procedures, installation, QA/QC, and recommended load test verification criteria. Use of helical smart piles to validate helical pile design and verification of ultimate pile capacity is highlighted.

Jan 1, 2011

By Peter Middendorp, Gerald E. H. Verbeek

"This paper will describe a brief history of the method of characteristics as an accurate solution of the wave equation, and the author's experiences with the method of characteristics over a period of 30 years.As a result of the offshore pile driving activities associated with the development of the North Sea oil fields in the 1970's, two Dutch companies initiated extensive research efforts. Heerema started to research the dynamic behavior of soil during driving and HBG (Hollandsche Seton Groep) extended the method of characteristics with a straightforward theoretical solution for the shaft friction along a pile.The research institute TNO started the development of the wave equation program TNOWAVE in the late 1970's based on HBG's friction model extension for the method of characteristics. Today the program has a worldwide application in the field of pile testing. This paper will describe its development and application over time and its relation to today's applications for driveability studies for impact hammers (PDPWAVE) and vibratory hammers (VDPWAVE), signal matching for Dynamic Load Testing (DL TWAVE), Pile Integrity Testing signal matching (SITWAVE), and Statnamic simulation (STNWAVE).The paper will highlight that these developments have been the result of multi-disciplinary and multi-national efforts and encourage geotechnical engineers to seek further developments of the wave equation program in a similar manner. Finally, the paper will indicate some areas where such further developments are required."

Jan 1, 2005

By Quanchen Sun, Mohammed Z. E. B. Elsahife, Anthony Fisher, Chris Barker, Jennifer Schooling

A review of the literature shows that pile integrity is a significant concern in pile construction. Recently, a new integrity test, thermal integrity profiling (TIP,) has been put into use in foundation construction. It measures temperature changes and thermal profiles of concrete during curing. Heat generation and dissipation of early-age concrete is determined by the concrete mix, the ground conditions and the shape of concrete structure. The current data interpretation practice is primary based on experience. Anomaly detection through direct analysis of temperature profiles is currently indicative or suggestive and temperature signatures are usually similar, and numerous causes are not easily isolated. The core of the TIP testing technique, i.e. collecting detailed temperature measurements along the pile during the hydration process, is promising but a new interpretation approach is required. In this paper, a new interpretation approach has been developed in which TIP constitutes the first step. An investigative staged process is then followed to establish and assess the anomalies in the problematic regions along the pile employing the combined use of detailed finite element (FE) simulations, the actual temperature data from TIP and genetic evolution algorithms. In each stage, more details could be revealed about the anomalies being investigated including, ultimately, location, size and shape; this staged process enables practitioners to follow a riskbased approach and decide whether or not to pursue subsequent stages depending on the results they get at the end of each stage. This new approach, depending on the stages required for the analysis, will potentially avail practicing engineers of crucial test results about the quality of the pile immediately following pile construction, hence enabling repair and remedial work straight away at a lower cost.

May 1, 2022