Search Documents

By Erin N. Legault-Seguin

The Lac des Iles Mine (LDI) is located approximately 100 km northwest of Thunder Bay, ON. The mine has been in operation since 1993. The initial mine production was 2,300 mtpd and increased to 15,000 mtpd following a mine expansion project that was completed in 2001. Effective Oct. 29, 2008, LDI was shut-down under care and maintenance due to low metal prices. Prior to shutting down, LDI was the only primary PGM deposit in operation in Canada and of the few found globally. The complex geology and physical properties of the deposit causes several challenges for the concentrator. This paper will discuss the solutions to the main challenges of attaining nameplate tonnage and achieve satisfactory Pd recovery and concentrate grades.

May 1, 2009

By O. Worku, J. H. Masliyah, Z. A. Zhou

ABSTRACT The viscosity of concentrated kaolinite or illite clay in aqueous suspensions was measured in the presence and absence of a small amount of montmorillonite (<1 wt%). To avoid solids settling and to increase the sensitivity of the suspension viscosity measurements, solids concentrations higher than 38 wt% were used. The pH of the suspensions and the concentration of calcium and bicarbonate ions were found to significantly impact the viscosity of the clay suspensions. The results showed a significant increase in the viscosity of kaolinite suspensions with the addition of as low as 0.25 wt% of montmorillonite on a solids weight basis. In addition to illustrating the role of water chemistry in modifying slurry rheological properties, our study demonstrated that viscosity measurement could be a simple, yet sensitive technique for determining the content of smectite clays, such as montmorillonite, in a complex mix of various types of clay.

Jan 1, 2012

By L. Connolly, F. R. De Luca

"Rubber liners at Denison Mines Limited are used in 10 1/2x 24' low discharg0 pebble mills. These were originally 10 1/2 x 13 Dominion overflow type ball mills. Experience here shows that the wear of rubber and ni-hard lifters is approximately the same in the feed end half of the mill, while the wear of rubber lifters is much greater in the discharge half. The wear of rubber plates is considerably less than white iron in the feed end half of the Mill and slightly more in the discharge end half of the Mill. Rubber components are lighter to handle but their installation is time consuming. This leads to the conclusion that a combination of ni-hard lifters a~~ rubber plates is the most economical compromise in Denison's case, for the Mill. Rubber discharge grates are superior to steel grates, while steel feed end liners are superior to rubber.The Use of Rubber Mill Liners at Denison Mines LimitedGrinding is done in two identic0al circuits each consist-ing of one 10 1/2 x 14' Dominion overflow rod mill, two Dorr Oliver quadraplex rake type classifiers, two 10 1/2 x 24' Dominion low discharge grate pebble mills and ancillary pumps and conveyors for pebbles. There is one centrally located distributor box that receives the discharge of the 4 pebble mills and splits it out to the classifiers."

Jan 1, 1974

By D. Duff, R. A. Cameron, R. E. S. Whitehead

"Although CO2 content indicates the quantity of carbonate in altered basaltic rocks, it does not measure the intensity of carbonate alteration. CO/CaO molar ratios, which correlate with the relative proportions of individual carbonate species, measure the intensity of carbonatization. The Timmins gold area is characterized by pervasive carbonatization, with large parts of the area having CO2/Ca0 ratios greater than 1, representing C02 supersaturation relative to CaO. The mean CO/CaO in the Timmins area is0.67, compared to 0.13 in two unmineralized control areas. Regional arsenic abundance in the gold-bearing area averages 4 ppm, compared to about 0.35 ppm for the non-mineralized areas. The average K20 and Rb abundances are similar in both mineralized and non-mineralized areas (about 0.30% K20 and 7 ppm Rb). Although there appears to have been no wholesale addition of K20 or Rb to the mineralized area from external sources, these alkalies have been redistributed internally, resulting in patterns of local enrichments and depletions which are characteristic of the mineralized region.Local target anomalies associated with known mineralization consist of CO2/Ca0 > 1.5, As > 10 ppm and K2O > 0. 75%. Not all three values are required to be above these thresholds in order to identify local targets. Combinations such as C02/ Ca0 > 1.5 and As < 10 ppm, CO/CaO 1-1.5 and K20 > 0. 75 or K20 > 0. 75 and As > 10 ppm are equally indicative of proximity to gold occurrences. Gold-bearing veins and associated anomalies occur throughout the entire volcanic succession and are not restricted to any particular stratigraphic horizons. The levels and patterns of alteration and occurrences of gold appear to be structurally controlled."

Jan 1, 1982

By R. B. Throndycraft

"1. Belt-Drop Agglomeration Preferred at Heap Leach Operations. The agglomeration method now preferred at heap leach operations utilizes belt-drops along conveyors. Belt-drop agglomeration is being designed into numerous upcoming heap leach operations. It offers substantial capital cost savings over previously favored drum agglomerators. It has such significant operating and maintenance advantages that some drum agglomerators have been retired in favor of belt-drops.The majority of heap leach operations are now built with crushing included in the flowsheet. If crushing is included, belt-drop agglomeration can be added for almost no cost. The agglomeration equipment is simply a few conveyor transfers, designed to provide the tumbling and rolling action which forms the agglomerates. Controlled water sprays are needed at each of these agglomeration transfers. Cement or lime is added as a binder, to stabilize the agglomerates. This reagent is also needed to raise pH to safe operating levels.Addition of the pH control reagent before stacking the ore offers a reagent cost benefit. In the belt-drop mixing technique, the ore is intimately mixed with the lime (or cement). After stacking on the heaps, when the cyanide solution is sprayed onto the high-ph ore, very little cyanide is consumed. Without the pre-addition of lime or cement, the leach solution is sprayed onto neutral ore. The mixture of high-pH leach solution and neutral pH ore causes the solution pH to drop, releasing cyanide gas. This release is minor from a safety viewpoint, much less than dangerous, but the gas release is a costly waste of the cyanide reagent. Pilot-scale comparison tests were made at Pinson. Ore pre-treated with lime or cement showed 30% less cyanide consumption than untreated ore."

Jan 1, 1989

By P. G. Roden, G. A. Maki, P. J. Fullmann

"In October 1984, Rocanville Division began using a stacking system to handle potash mill tailings. Previous to this date, mill tailings were slurried to the top of the tailings pile and allowed to debrine while flowing mobile stackers. The stackers consist of cyclone packs to debrine the tailings and drag conveyors with screw discharges to deposit the tailings onto the existing pile. The paper will deal with the various aspects of the project from conception to its present state. Key Words: stacking, mobile stackers, Linatex Separators, potash mill tailings, reclaim brine ponds, settling ponds, tailings pile. IntroductionPrevious to 1984, when the stacking project was first implemented, potash mill tailings were handled as follows. Mill tailings were first debrined to approximately 65% solids using a cyclone cluster. The cyclone underflows were then introduced onto a vacuum scroll filter table. Here the tailings were further debrined and discharged into the disposal tank where the tailings were reslurried with reclaim brine and pumped to the tailings disposal site. At the disposal site the slurry was discharged onto the tailings pile and by a natural settling process the tailings were debrined with the brine ultimately collected in the reclaim brine ponds. The shape and profile of the tailings pile was controlled by building salt dikes to control the flow of the discharged tailings slurry. As the tailings pile grew in height, booster pumps were added to the disposal system."

Jan 1, 1986

By David W. H. Ellis

This presentation will discuss over 2 dozen past, present and future oils sands projects in Alberta. The very early projects as well as the most recent along with the ones that never got off the ground and the ones in production are all included. For each, the following will be given (where known): owners, location, type (mining/SAGD/refinery), production, capital budget, spent to date, status. Some overall impacts will be discussed.

May 1, 2004

By E. Esponosa-Gomez, J. A. Finch, A. R. Laplante

"Water quality plays an important role in oxide flotation. The effects on selective flotation of fine (1-16 um) pyrochlore of two types of water used at the Niobec concentrator, potable and plant recycle, were assessed. Several pyrochlore collectors and silicate depressants were tested. Water effects were different for each mineral-reagents) combination. In general plant recycle water decreased selectivity and increased reagent consumption. Interpretation of results is given in terms of electrokinetic effects, hydrolysis of cations, and mineral-collector interactions. Two techniques of treatment for plant recycle water, cation precipitation and zeolite adsorption were assessed. The former was found to be more effective under the tested conditions but recycle water continued to give poorer selectivity than the potable.INTRODUCTIONWater quality plays an important role in selective flotation. Specific effects have been reported by many workers (1-6) and in general the better the water quality the more selective is flotation. Water composition depends on origin and the minerals being processed. For example pulp containing salt-type minerals (calcite, apatite, dolomite) will contain more Ca and Mg cations than that from a sulphide deposit. Another source of water contamination is the flotation reagents added to the pulp, particularly if water recycling is practiced."

Jan 1, 1986

By V. K. Gupta

"Effect of mill speed on grinding kinetics has been investigated with a view to using mill speed as a manipulated variable for control and optimization of the grinding circuit performance under variable ore hardness conditions. Dry and wet batch grinding tests were carried out for quartz, limestone and cement clinker in a 29 cm x 18 cm laboratory ball mill. Mill speed values selected were 55 and 70% critical. In the case of dry grinding operation, with an exception of quartz, for all materials studied the effect of mill speed on grinding rate was found to be insignificant for sizes finer than about 35 mesh. In the case of wet operation, grinding rates were found to be approximately proportional to the mill speed. The implications of these results are discussed.INTRODUCTIONIt is well known that mill speed has a considerable effect on the grinding rate of the ore particles l-3 For particles of a given size there is an optimum speed at which mill grinding efficiency is maximum (i.e. specific energy consumption is minimum) 3•4. Mill speed can, therefore, be effectively used as a manipulated variable to deal with the disturbances arising from changes in the size and hardness (grinding rate) of the ore being fed to the grinding circuit. Though, it has not been the case so far, with recent developments of ring motors2 and frequency inverters5 a continuous variation of mill speed has now become feasible, and it is expected that mill speed control will soon be a regular feature of plant operation2,6."

Jan 1, 1985

By J. -C. Sztuke, M. Cao

ABSTRACT The correlations between froth recovery of coal and air recovery were investigated using a hybrid mechanical flotation column. The particle slurry was fed onto the surface of air-water two phase froths to carry out the tests. Froth recovery was taken as the recovery of particles into the froth product, whereas air recovery was determined by the froth height method. The relationships between froth recovery and air recovery were nearly linear, with greater slopes for more hydrophobic particles. Inside the froth phase, the particles were stratified, with hydrophobic particles concentrated in the upper region and hydrophilic particles in the lower region.

Jan 1, 2013

By N. Hmidi, T. Yalcin, M. Papadakis, B. Hilscher

Mill tailings, containing iron sulphides in particular, pose an environmental concern since they constitute a potential source of acid mine drainage which can damage vegetation, harm soil and living organisms, and contaminate groundwaters. Proper disposal of acid generating tailings is therefore an important issue that must be addressed and resolved in a satisfactory manner. Placer Dome Canada operates a 4000 t/d gold cyanidation facility at Musselwhite mine, in northwestern Ontario, where the mill tailings have been classified as acid generating. This study was conducted to explore the effectiveness of froth flotation in removing the sulphide minerals from these tailings and producing a low-sulphur, non-acid generating material that could serve as a capping material for previously deposited tailings. Laboratory semi-batch flotation tests were carried out in accordance with an experimental design procedure, and a computer simulation program was developed to facilitate the evaluation of flotation performance. In this investigation, pH, collector concentration, and airflow rate were considered as the relevant flotation variables, and their effects were examined both experimentally and by simulation. Results have demonstrated that flotation can successfully desulphurize the Musselwhite mine tailings and render them non-acid generating.

Jan 1, 2004

By R. H. Walton

"In recent years the recovery of copper from low grade oxide ores has received widespread attention. The cost of treating such ores using conventional technology, such as milling and flotation, is frequently prohibitively high and copper recovery is generally low. The introduction of heap leaching, solvent extraction (SX) and electrowinning (EW) has resulted in high recoveries, good copper cathode quality and low production costs. This technology has now been successfully applied on a worldwide basis.This paper reviews the various process and design options and gives approximate capital and operating costs for a 1.0% copper ore.INTRODUCTIONAs a result of the low copper prices that prevailed for much of the last two decades, aggressive attempts were made by the industry to cut operating costs. Under such circumstances heap leaching, solvent extraction and electrowinning, to recover low cost copper from oxide ores, has received particular attention and ultimately widespread acceptance.Low grade copper ore (typically containing less than 1.0% Cu), which could not be economically treated by other methods, is placed on heaps and leached with dilute solutions of sulphuric acid. The copper rich, pregnant solution, drains from the heap into a collecting pond and is pumped to a solvent extraction plant where it is purified and upgraded. The resulting solution, termed the pregnant electrolyte, passes to the electrowinning section where the copper is recovered as high grade cathodes and sulphuric acid is regenerated, (Figure 1).This paper specifically describes the processing of copper oxides. Other copper minerals such as chalcocite and chrysocolla are also leached by dilute solutions of sulphuric acid. In practice the oxide minerals are frequently associated to varying degrees with less easily leached sulphides, such as chalcopyrite. In some cases, once the oxidized capping of the ore body is removed, the oxides are totally replaced by more refractory sulphides. Under these circumstances the leaching recovery is significantly reduced. However the principles described here for solvent extraction and electrowinning are also applicable to solutions received from heaps containing sulphide minerals, which are leached more slowly and involve bacterially induced reactions."

Jan 1, 1990

By G. Simard, M. J. Gagnon, A. Charette, G. Péloquin

"In the Bayer process, flocculants are introduced in the feed well to enhance the aggregation of red mud particles. To gain a better understanding of the flocculation process taking place in the feed well, shearinduced flocculation was achieved using concentric rotating cylinders (Couette system). Our previous work has shown the effect of the shear rate on the aggregate’s settling rate and on residual turbidity of the Bayer liquor. In this study, the data demonstrated that the aggregates at selected shear levels appear as a population with a widespread size distribution. By using an imagery apparatus, it was possible to measure the size, the shape, and the sedimentation velocity of the larger red mud aggregates. Marked differences were noticed in the characteristics of the aggregate populations obtained under various shear conditions. IntroductionIn the Bayer process, red mud particles are separated from the liquor in primary clarifiers and washing circuits under the action of synthetic polymers. The agitation in the feed pipe and in the feed well affects the flocculation since the aggregates are formed by the interaction between the red mud particles and the polymers. A minimum shear rate is needed to initiate the aggregation process of fine particles (Warren, 1975).Different systems have been used to study the effects of shear on the flocculation process (Tampo and Watanabe, 1979; Klimpel and Hogg, 1986; Scott et al., 1996; Biggs and Lant, 2000). The Couette flow system has been used in some studies on shear-flocculation (Oles, 1992; Farrow and Swift, 1996a, 1996b). The importance of the physical properties of the aggregates in determining the efficiency of the solid-liquid separation process within a given gravity thickener has been demonstrated (Farrow and Warren, 1989a)"

Jan 1, 2002

By Keith R. Vining

Solid fuel, usually coke or anthracite, is commonly added to ground iron ore fines in the pelletising process to reduce the amount of burner fuel required and the maximum firing temperature, while maintaining pellet strength and the productivity of the pelletising plant. However, the use of coke and coal contribute to the production of greenhouse gases (eg carbon dioxide) and are a source of NOx and SOx emissions. Utilising wood biomass / wood char is one methodology CSIRO Minerals is investigating as an alternative to coke and coal, as it is a renewable energy source that is very reactive, has a low ash content and the potential to reduce emissions of greenhouse gases from the iron and steel-making process. Previous work has established that charcoal can effectively replace coke in the sintering process (Lovel et al, 2005), and the following experimental work aims to demonstrate that it can also provide an adequate replacement for coke and coal in the pelletising process. The paper presents the results of an experimental testwork program comparing the behaviour of fired pellets containing traditional solid fuels and charcoal. The physical properties of the pellets are compared in terms of their compressive strength, tumble and abrasion indices and the reduction properties. A qualitative assessment of the pellet microstructures is also presented.

May 1, 2007

A direct comparison has been undertaken between laboratory wind tunnel experimentation and computational fluid dynamics simulation of a 3D manufactured analogue for a body of fractured broken rock, created with CAD/CAM techniques. Detailed descriptions of the ?design? of the analogue (using a discrete element analysis multi-body simulator), its manufacture (using computer aided design and 3D printing technology) and the laboratory experimentation (inserting the physical analogue into a laboratory scale wind tunnel) are presented. The agreement of the results of direct experimental observations on the manufactured analogue with the values from CFD simulations of those experiments justifies the utilization of a CFD environment for the practical investigation of geometric factors controlling air flow and heat exchange in complex assemblages of broken rock blocks. The ultimate goal is described, that of developing functional relations between bulk properties of such assemblages (such as their porosity and bulk density) and the low-level geometric factors that dictate the air flow behaviour, such as the equivalent perimeter length of the cross-sectional area available for flow, or average flow path tortuosity. A practical application area of the work in the mining context is also described; equivalent continuum air flow and heat transfer constitutive models developed on the CFD tool from such functional relations are useful in characterization of seasonal heat storage in large scale bodies (approximately 1 km3) of broken rock.

Aug 1, 2013

By A. Cabañas

"In this paper, geostatistical techniques are applied to forecast the annual copper price in the short and medium terms (from one to five years ahead). These techniques allow the incorporation of monthly and multivariate information in the analysis and provide more accurate results than traditional approaches, especially as far as the one-year forecast is concerned.A second advantage of geostatistics stems from its ability to assess the uncertainty associated with the unknown future prices, thanks to estimation variances or confidence intervals, depending on the technique used. Such an assessment has a crucial importance in decision-making, from both macroeconomic and microeconomic points of view. IntroductionThe copper price traded in the London Metal Exchange is a relevant parameter for defining macroeconomic policies of producing countries like Chile. It is also a key factor for the mining companies, since fluctuations in the sell price affect the expected financial flows. Due to the amount of money involved in decision-making, it is necessary to have accurate forecasts of the future copper prices and to quantify the uncertainty associated with such prices.This paper focuses on the annual copper price estimation in the short and medium terms, i.e., from one to five years into the future. Henceforth, the word “estimation” will be used as a synonym of “forecast,” according to the geostatistical jargon (Matheron, 1989).Two main approaches, based either on statistics or econometrics, are currently used to forecast commodity prices, but both of them are not very accurate when applied to copper. First, the main methods are briefly reviewed, then the geostatistical formalism will be presented. So far, the latter approach hardly has been used to estimate commodity prices, although it may reconcile both statistics and econometrics via (1) the use of a stochastic approach and (2) the handling of ancillary variables related to the copper market. Another advantage of geostatistical techniques is the ability not only to forecast the copper price, but also to measure the uncertainty associated with it."

Jan 1, 2004

By R. Filippone, Donald Leroux, Colin Hardie, G. Leichtle, Cesar Gomez, Jim A. Finch

"Bubble surface area flux (Sb) is the surface area of bubbles per unit time per unit cross-sectional area of flotation machine. The units are: (m2 bubble surface/s)/(m2 cell) or s -1. For bubbles of mean size db (m), s b = 6-Qg/A db where Qg is the gas rate (m3/s), and A the cell cross-section (m'). This parameter is now receiving wide attention as the possible key machine variable in flotation diagnosis and modelling. The concept is described and the potential use of sb is illustrated by work on flotation columns and mechanical cells. In column flotation of recycled paper, the dependence of ink recovery on s b was the same regardless of size of column or type of sparger. In mechanical cells, it has been established that the rate constant is related to Sb independent of impeller type.The use of s b is limited by the problem of measurement, primarily that of estimating db. A prototype probe designed to estimate db (and hence sb) based on conductivity measurements is described. Exploratory work with the probe in a mechanical cell suggests the promise of making estimation of s b routine.INTRODUCTIONFlotation is the result of interaction among variables associated with the feed particles, chemistry and the machine (flotation cell). Trying to isolate the effects of each aids in process diagnosis and is at the centre of attempts to model flotation. The machine variables that have been investigated include the air flow number, the power number and specific power (Harris, 1976). None have survived as the basis for predicting flotation response perhaps because they did not include directly the properties of the bubble swarm (or dispersion). Recently, Gorain (1 997) explored the relationship between the flotation rate constant and various ""gas dispersion"" parameters notably: superficial air rate (Jg = Qg/A, where Qg is the volumetric gas rate and A is cross-sectional area of cell), bubble size (db), gas holdup (Eg, i.e., the volumetric fraction of a cell occupied by gas) and bubble surface area flux (sb = 6.Jg/db). Of them all, Gorain et al. (1997) conclude that the latter, the surface area flux, correlated best with the flotation rate constant. This concept was adopted from column flotation where it was used to estimate, among other factors, the maximum amount of gas that could be injected (Finch and Dobby), 1990). Let's start by reviewing the concept. Following that some examples of where the concept has been applied will be described to illustrate the current interest and finally we will consider how to measure the surface area flux."

Jan 1, 1999

By The Staff

FOR forty years cyanide men have been intensively engaged on the treatment of sulpho-telluride ores. So far as we know, the processes used today were-with the important exception of the concentration plus high-lime process at the Victor mill (1915)-in use, or had been tried, in the earl y years of the century. Roasting, bromocyanide, ordinary cyanide, table and vanner concentration, floating and treating the concentrate, roasting con-centrates prior to treatment, etc., all were used at Kalgoorlie in 1904 or earlier. Flotation, followed by shipment of the concentrate to the Golden Cycle mill, was the practice at the Vindicator mine, Cripple Creek, for some years prior to 1917. Similar practice was employed in the Portland Independence mill at Victor, Colorado, and was lacer superseded by the table concentration, high-lime cyanide treatment of rails of the older Portland Victor mill. During all this time, an immense amount of research was being clone on these ores by the staffs of numberless companies. Conclusions were drawn and mills built. But if the results of one per cent of this research were ever published in sufficient detail for intelligent use by others, the Lake Shore staff has been unable to discover them, or does not recall having clone so. Government laboratories-as for instance chose of the Mines Branch, Ottawa, in or about 1927-have touched upon certain methods in their publications, but they simply have not had the time to finish the job. The paper by W. E. Johnston, Tellurides-Problem or Alibi? (E. & M.]., Aug., 1933), aroused wide interest and comment. It published conclusions, some right and some wrong, and gave the evidence adduced by the author i:n support thereof. Conclusions published without supporting evidence are to most of us worse than no conclusions at all. We suggest chat, if even one-tenth of the operators had published full, detailed results of their laboratory work, ad vance in the treatment of sulpho-telluride ores would have been very much accelerated. Therefore, we venture to inflict upon the Institute a compendium of the results of laboratory work performed during the past few years at the Lake Shore mill. It is really a summary of the more interesting results to date, prepared by the mill staff for their own use and benefit. But we hope chat the discussion under any heading is so detailed chat it will be intelligible to anyone interested in that phase of the subject.

Jan 1, 1936

By Carol E. Jones

Outline ? Reclamation is a primary mitigation. ? Understand baseline environment and land use. ? Determine reclamation goals. ? Selecting reclamation technology. ? Determine technical risk. Reclamation ? Primary Mitigation ? Through land and water disturbance, mining can have significant local and regional environmental impacts. ? Impacts can also result from associated land use changes. ? Reclamation is a primary tool that the mining industry uses to manage its environmental impacts.

May 1, 2008

By J. E. Udd

"In early 2000, CANMET-MMSL was engaged by the Ontario Ministry of Labour (OMOL) to conduct an international study of the practices, in several key mining jurisdictions, of determining the criteria that are used to decide when the wire ropes used in mine hoisting are to be retired from service. Subsequently, the author visited key officials and institutions in Canada, the United States, the Republic of South Africa, the United Kingdom, Germany, and Poland. Material from the Australian province of New South Wales and Hungary was also included.The report that resulted included, among other sections: (1) the history of wire ropes and trends in manufacturing technology; (2) a review of mine hoisting practices; (3) the requirements regarding safety factors; (4) a review of the various operations and their potential future development; (5) the criteria for rope replacement; (6) potential future developments that could take place in both hoisting and rope inspection practices in Canada; and (7) recommendations.Subsequently, the report was issued by OMOL, and as a CD-ROM by CANMETMMSL. In this paper the author presents the key findings and the recommendations made in the study."

Jan 1, 2004