Search Documents

By Cy Jordan, Ben Burdett, Adrian Dance, Jack Rainey

"In 1997, EIMCO Minerals installed a knowledge-based control system on one of the five primary grinding lines at Highland Valley Copper. The objective of the system is to maximise throughput without affecting circuit product size or flotation recovery. The system was commissioned in October 1997 on a SAG mill/ball mill circuit following a plant audit and upgrade of the control instrumentation.The system monitors and controls the SAG mill power, bearing pressure and recycle load by manipulating the solids feedrate, water addition and mill speed. The two ball mill and cyclone circuits are controlled through water addition at various points in the circuit as well as the number of operating cyclones.An on-line particle size analyser is used to measure the cyclone overflow quality. Models of the SAG mill charge level and overflow product size are also incorporated. A method of predicting the SAG mill power response to feedrate changes is used to lessen the effect of dead time for improved mill power control. In the future, inferred measurements of SAG feed particle size and hardness will allow changes in ore behaviour to be predicted and compensated for by the system.This paper describes the development of the project -from installation and commissioning to modifications and refinement -along with prospects for the future.BackgroundIn early 1997, EIMCO Minerals was contracted by Highland Valley Copper to install a knowledge-based or expert system control strategy on one of the five grinding lines in the mill. This was to become the start of the Advanced Control Project at Highland Valley Copper (HVC). This paper will review the progress of the Project as well as discuss the prospects for the future.Following a preliminary engineering study (or plant audit) by EIMCO in 1996, it was decided to implement an advanced control system in order to improve plant operations and increase productivity. The study suggested that such a system had a pay-back period of a few months through increased throughput without loss in flotation recovery. Highland Valley already had successfully applied higher level control through their Elsag Bailey distributed control system (DCS) and this was the next stage in process optimisation."

Jan 1, 1998

By Alvaro Diaz

Introduction, who is Teck Red Dog and Quebrada Blanca Mines Uniqueness of environment Arctic versus High Altitude Conditions Logistical challenges People and Stakeholders Conclusions

May 1, 2013

Sustainable Development SAFETY ?Safety is the most important element of sustainability. ?One bad experience or incident can mar a company?s reputation for a long, long time. ?News travels faster than ever ?Internet, blogs, texting, peer-to-peer communication, etc. and unfortunately sometimes the information is not always accurate. ?Rarely do we hear in the news about the mining companies or projects that are done safely ?we always hear about the exceptions. ?Safety is just like TQI / TQM ?the process of improving can never stop.

May 1, 2010

By R. C. Urquhart

Since the first use of the electric arc furnace Henri Moissan (1892) and its use by Paul Hérholdt (1902) to melt steel, it has been successfully used as a pyrometallurgical smelting tool in the production of calcium carbide, iron, ferrous and non-ferrous alloys. Commercial forms of the electric arc furnace have evolved from round, single-phase single electrode units to rectangular three electrode three-phase units to round three electrode three phase units and ultimately to rectangular six electrode three-phase units. DC electrical supply has also been used to replace the three phase power supplies in some cases. This paper examines how these electric arc smelting furnaces have evolved in size, efficiency and configuration within the constraints of the smelting process, electrodes and electrical power supply equipment.

Jan 1, 2014

By O. A. Ojo, R. G. Ding, M. C. Chaturvedi

In this study, the fusion zone microstructure of tungsten inert gas weld of a directionally solidified NhAl-base alloy was examined by the standard metallographic techniques involving the use of optical, analytical scanning and transmission electron microscopes equipped with energy dispersive spectrometer. Fusion zone cracking was observed to be closely associated with interdendritic secondary solidification microconstituents identified as consisting of y, y' and NiMo (Y) phases. Depression of solidification temperature to the terminal ternary eutectic reaction temperature of the system during cooling is suggested as an important factor contributing to the fusion zone cracking.

Jan 1, 2006

By Fathi Habashi

New technology first introduced by Nippon Steel Corporation at Kitakyushu in Japan in 1976 now used at a number of plants in other countries, known as dry quenching of coke, uses nitrogen in a closed circuit to avoid environmental emissions. In addition, heat is recovered in the form of steam, from the red-hot coke. In steel plants oxygen is used extensively and therefore by-product nitrogen from air liquefaction can be effectively utilized in this way.

Jan 1, 2014

By R. Bonifaz

The Chagres Smelter, part of the Anglo American plc group situated 80 Km north of Santiago in Chile, completed a series of operational improvement in 2005 resulting in an optimum capacity in its operational units. At present the Chagres Smelter has developed an operational strategy which seeks to reduce bottle-necks in the production process. In this way we have managed to lower operational cost, decrease energy consumption and maximize the capacity of the Acid, Oxygen, and Smelting, Converting, Refining and Casting units. A constant application of international benchmarks together with continuous staff improvement and the latest smelter technology have combined to place Chagres among the finest smelting works in the world. In response to environmental challenges, we have studying various options for investment suitable for a profitable business of benefits to both Anglo American and Chile as a whole. The most relevant technical indicators are the figures : Energy consumption less than 6,3 GJ/ton fine copper, Intensity of smelting rate in Flash Smelting unit of 6900 ton of copper concentrate/m2 settler of furnace area and be one of the top five smelter in direct cash cost .

Jan 1, 2007

By E. G. C Charlesworth, M. J. Robertson

"Gold mineralization in the Main Reef Complex at Sheba Gold Mine is hosted within shear zones in a sequence of shales and greywackes of the Fig Tree Group. Competency contrasts between these rocks and a steeply dipping chert unit provided a locus for the development of right lateral steeply dipping shear zones. A set of flatter dipping shear fractures crosscut these zones with their intersections defining a system of en échelon ore shoots. Mineralization is both of vein type and disseminated strata-controlled replacement type. The latter occurs mainly within the wall rocks to the shear zones. Arsenopyrite and pyrite are the major sulfides, with arsenopyrite being confirmed largely to greywacke beds and pyrite to the more iron-rich shale units. Gold was introduced, together with minor sphalerite, pyrrhotite, chalcopyrite and early arsenopyrite, toward the end stages of a first pyrite phase. The mineralizing fluids were introduced along dilated cleavage planes and, emanating from these, produced a series of replacement fronts. Mineralization was syntectonic to late tectonic and occurred under conditions of progressive deformation, resulting in sulfides which are concentrated in the hinges of shear-related folds and semimassive sulfides within tension fractures which are folded, attenuated and fractured. An analysis of the structures shows a sequence of events in which an initial ductile simple-shear event with a steep sense of movement was succeeded by a more brittle strike-slip event. Mineralization is temporally related to the latter. This evolution in structural style was probably related to reactivation of the Sheba Fault as a transcurrent fault during emplacement of large granitoid bodies."

Jan 1, 1994

By Alain Tshilombo, Vijay Reddy, Chowdary Meenavilli, Kelvin Buban, Cory Kosinski, Sriraj Meenavilli, Siddhartha Tirumalaraju

The use of artificial intelligence (AI) for process optimization is expected to play an increasingly important role in the future of the mining industry. The objective of AI is to develop a data driven soft (virtual) sensor using historical data that can estimate unmeasurable characteristics of the process and provide appropriate recommendations during operation to optimize the process through continuous learning. The application of AI to a hydrometallurgical process was evaluated by Sherritt Technologies in coordination with NTWIST. Historical operating data obtained from the Ambatovy facility’s High Pressure Acid Leach (HPAL) circuit was used to develop models to predict autoclave discharge parameters based on operating conditions and ore mineralogy. The prediction models were developed in such a way to also allow the user to simulate and test different operating conditions. A second set of models (AI model) were developed based on the prediction models, economic data and operating constraints for a given process unit to identify optimal reagent and steam dosages across the HPAL circuit. The development of these models was significantly complex due to the dynamic and interactive nature of the HPAL process. Despite the complexity of the models, the models were able to predict, with accuracy, the relationship between ore composition, leach autoclaves retention time, acid addition and steam addition with metal extractions as well as levels of impurities in the autoclave discharge slurry. The study showed that AI has the potential to improve the overall operation of a facility through providing tools to assist with training, troubleshooting and process optimization. INTRODUCTION The Ambatovy project, located in Madagascar, is one of the world’s largest nickel and cobalt mining and processing operation, with a design capacity of 60.000 tonnes of nickel and 5,600 tonnes of cobalt per year (Collins et al., 2016). Commissioning and start-up of the Ambatovy mine and plant facilities were completed in 2012, with acid first introduced to the ore leach in March 2012. Commercial production (defined as 70% of design capacity) was achieved in January 2014 and the production level required to achieve financial completion (90% of design capacity for 90 days) was achieved in March 2015 (Valle et al., 2016). Figure 1 shows a simplified flowsheet of the hydrometallurgical pressure acid leach (PAL) process employed by Ambatovy.

Jan 1, 2019

By T. G. Joseph, R. K. Soni, M. Curley

"Rapid dampening suspension is a proposed suspension design for ultra-class haulers that is intended to avoid metal-to-metal contact inside a strut and under shock loading, thus improving ride quality and ameliorating fatigue loading issues on a hauler structure. Laboratory testing has shown the ability of the proposed design to reduce the opportunity for bottoming out, that is, metal-to-metal contact between the colliding ends of oleo-pneumatic, two-piece suspension struts during the compression cycle. This paper predicts the performance of a full-size rapid dampening suspension strut by applying scaling rules to test the proposed design based on a set of field data from a Caterpillar 797B ultra-class haul truck operating in the oil sands region of the province of Alberta, Canada. The predicted performance of the suspension strut is compared to that of the original equipment manufacturer model, which was monitored on board the truck during field data collection. ¦ KEYWORDS Haul truck, Original equipment manufacturer (OEM), Rapid dampening, Strut, Suspension RÉSUMÉ La suspension à amortissement rapide est une conception de suspension proposée pour des camions de transport de catégorie ultra-class (des engins dont la charge utile dépasse les 320 tonnes métriques), visant à empêcher un contact métal sur métal à l’intérieur d’une jambe de suspension et dans des conditions de choc au chargement. Elle améliore la qualité du roulement et les problèmes de charge de fatigue sur la structure d’un camion de transport. Les essais en laboratoire ont confirmé que la concep¬tion proposée évitera au cylindre interne de heurter le cylindre externe, autrement dit empêchera le contact métal sur métal des jambes de suspension oléopneumatique en deux parties pendant le cycle de compres¬sion. Cet article prévoit la performance d’une jambe de suspension à amortissement rapide à taille réelle en appliquant les lois d’échelle afin de mettre à l’essai la conception proposée, sur la base d’une série de données de terrain relatives à un camion de transport 797B de catégorie ultra-class de Caterpillar (aujourd’hui remplacé par le nouveau modèle 797F) utilisé dans la région des sables bitumineux de la pro¬vince de l’Alberta, Canada. On compare la performance prévue de la jambe de suspension à celle du modèle du fabricant d’équipement d’origine (FEO), qui a été contrôlée à bord du tombereau pendant la collecte des données de terrain. ¦ MOTS CLÉS amortissement rapide, camion de transport, fabricant d’équipement d’origine (FEO), jambe de suspension, suspensionINTRODUCTION Research basis for the paper This paper is based on the unpublished MSc thesis work of El-Sayed (2003), Santos (2007), and Soni (2009) under the direction of Dr. Tim Joseph within the oil sands–equipment interactions program (OsEIP). OsEIP is part of the Alberta equipment–ground interactions syndicate (AEGIS) surface mining research group, School of Mining and Petroleum Engineering, University of Alberta. The aforementioned work spanned a decade of progressive studies into rapid dampening suspension systems, leading to the scale performance indications highlighted here. Although this paper uses a specific Caterpillar 797B suspension strut for field monitoring and as a basis for scale prediction of a modified rapid dampening suspension strut design, the design scaling principles used here could be applicable to any such design change consideration for an oleo-pneumatic suspension system."

Jan 1, 2019

By G. E. Rodger, R. Jugoon

"SUMMARYSamples of Aunor gold precipitates which varied widely in gold content were fluxed to produce a bisilicate slag with various oxidizers and combinations of oxidizers. On the basis of some preliminary tests a flux composition was chosen which appeared to show the most promise.The different components of this flux were then incorporated into a matrix for a 23 factorial design experiment to determine what were the most important variables and what changes should be made to the flux composition to optimize the resultant total bullion fineness.The results of the 23 factorial design experiment showed that the flux composition as calculated was very close to an optimum as only very minor changes were required to give bullion in excess of 995 fine.INTRODUCTIONEarly in 1969 the results from the Aunor Gold Mines refinery showed that wide variations existed both in precipitate grade and in total bullion fineness. An analysis of this data showed that as the precipitate grade increased, the gold bullion fineness also increased (see appendix 1). Therefore, to improve the refinery results test work was initiated to: 1) improve the precipitate grade and 2) to determine, with the help of statistics, a flux composition which would be able to handle wide variations in precipitate grade and give a total bullion fineness in excess of 950 fine."

Jan 1, 1970

"With the plethora of cable bolts on the market, geotechnical engineers can be baffled by the differences in performance claims from the manufacturers but perhaps more importantly they are sometimes at a loss in making an optimal selection matching behaviour with a particular site condition. To this end a new testing methodology has been developed that can cater for the varying types of cable bolt behaviours. The methodology is based on the laboratory short encapsulation pull test (LSEPT) as recommended in the British Standard and overcomes several deficiencies such as cable rotation. Of most significance however, is its inability to measure the post-peak residual performance of high load transfer capacity cables and consequently, there is an inference that these cables may be susceptible to sudden anchorage failure with relatively little yield. This paper details the results of anchorage performance tests of a range of cable bolts and the differences in performance with rock strength and drill hole diameter.INTRODUCTIONA research project was undertaken to develop a new laboratory-scale test apparatus to study the axial performance of fully grouted cable bolts that are used in the Australian underground coal mining industry. Work by Thomas (2012) and others in recent years found there were a number of deficiencies in the testing methodologies making it difficult to determine and compare the performance of the dozen or more different types of cable bolts on the market. This has meant that geotechnical practioners have been hamstrung in optimizing the design of ground support systems in underground environments that are increasingly more arduous.A cable bolt is a flexible tendon consisting of a quantity of wound wires that are grouted in boreholes at defined distances between holes in order to provide ground reinforcement of excavations (Hutchinson & Diederichs, 1996). They were initially introduced into the underground hard rock mining industry in the 1960s (Thorne & Muller, 1964) and since the early 1970s have been brought to coal mining operations."

Jan 1, 2015

By S. Koski, J. Vanderbeek, J. Enriquez

"The Cerro Verde copper-molybdenum porphyry mine, majority owned and operated by Freeport- McMoRan Copper & Gold, is located 30 km southwest of Arequipa Peru. The concentrator, which produces copper and molybdenum concentrates, started operating in late 2006 with a 108,000 tpd design capacity, processing primary sulfide ore (mainly chalcopyrite and molybdenite). Plant capacity was recently increased to 120,000 tpd. The comminution circuit consists of one 60” x 113"" primary crusher, four MP-1000 secondary crushers in closed circuit with dry screens, four 2.4m x 1.6m High Pressure Grinding Rolls (HPGRs) in closed circuit with wet screens, and four 7.3m x 11m gearless ball mills in closed circuit with cyclones. The HPGR circuit is fed by the Secondary Crushing circuit product at a T80 of 35 millimeters, and the HPGR circuit product feeds the Ball Mill circuit at a T80 of 3000 microns.This paper describes operating experiences with HPGRs during these first four years highlighting improvements in operating practices and presentation of data regarding operational efficiencies, also discussed are the primary benefits provided by HPGRs such as production of micro fractured particles, reduced ore Bond Work Index, and reduced power consumption. Cerro Verde represents the first installation of HPGRs in both the copper industry and large scale hard rock mining."

Jan 1, 2012

By J. Mosher, G. Banini, J. Hollow, A. Villanueva

Prior to installation of High Pressure Grinding Rolls (HPGR) at PT Freeport Indonesia (PT-FI) a series of laboratory tests were carried out to determine the design parameters and also determine key performance indicators (KPIs) for the industrial unit. The design parameters derived from the lab test work were then scaled up to estimate the industrial capacity of the HPGRs to be installed. These parameters include specific power draw, specific throughput, and specific force, rolls speed, product size distribution and wear rate of the rolls. This paper compares the performance of the scale-up procedure against the installed industrial size HPGR. Overall, the specific throughput of the industrial size HPGR is higher by a minimum of 30% compared to the expected scale-up value. As a result of the high specific throughput, the specific power draw and grind sizes are below the scale-up expectations in the commercial application. The impact of these factors also contribute to a lower than expected wear rate on the industrial rolls. Installed rolls achieved a service life in excess of 18,500 hours relative to the target of 6,850 hours predicted from the laboratory testing.

Jan 1, 2012

By S. Pinard, A. Desbiens, R. del Villar, D. Jakelski

"During the fall of 1993, a new Pill-based control strategy was installed in the B grinding circuit at the Kidd Creek Division of Falconbridge Ltd. The control strategy was first evaluated on a grinding circuit dynamic simulator (DYNAFRAG), which permitted the discrimination between more than a dozen possible control alternatives. Once the final choice was made the necessary instruments were purchased and installed. The control strategy was configured on the plant computer and is planned to be commissioned shortly.This paper summarizes the control strategy, the design procedure, the installation and the controller tuning. Some preliminary problems posed by the process prior to implementation are also presented.IntroductionIn 1990 the GRAIIM (french acronym for Research Group on Computer Applications to the Mineral Industry) of Laval University started a research project on Knowledge Based Automatic Control (KBAC). This project is sponsored by a consortium of eight mining companies under the umbrella ofMI1EC (Mining Technology Council of Canada), the Quebec Mining Association (AMQ), CANMET and the Centre de Recherches minerales (CRM). The project also benefits from important grants from the Ministere de l'Education Superieure et de la Science and the NSREC-CRD program.The main objective of this project is the screening of advanced (knowledge-based) methods for data processing (filtering, mass balancing, etc.) and automatic control (model-based control) for their use in the mineral processing operations. The project also aims at transferring these tools to the industrial partners through annual workshops for plant engineers, annual symposia, and through specific in-plant projects where the participation of plant engineers is strongly encouraged.The main objective of this project is the screening of advanced (knowledge-based) methods for data processing (filtering, mass balancing, etc.) and automatic control (model-based control) for their use in the mineral processing operations. The project also aims at transferring these tools to the industrial partners through annual workshops for plant engineers, annual symposia, and through specific in-plant projects where the participation of plant engineers is strongly encouraged."

Jan 1, 1994

By D. Seke, E. Katsande, R. Khumalo, K. Seerane

Palabora Mining Company (PMC) processes a multi-component ore body using a circuit consisting of two AG mills in parallel, closed with vibrating double deck screens and hydrocyclones. The bottom screen undersize feeds the hydrocyclones, but the screen oversize products can be treated in a variety of ways. The top deck screen pebbles can be crushed and then combined with the bottom deck oversize and recycled to the AG mill. Alternatively both the top and bottom deck screen oversize can by-pass the recycle crusher and be recycled directly to the mill. A full tap-off is a configuration when both the top and bottom deck screen oversize streams are stockpiled. The other configuration is when the bottom deck screen oversize is recycled to the mill while the top deck screen oversize is stockpiled - termed partial tap-off. This article reports the findings from the surveys performed to evaluate the performance of the PMC auto mill circuit when operated under the four different configurations discussed. Ore characterisation tests were performed to assess the deportment of the key ore components for the different configuration.

Jan 1, 2012

By Zhigao Xu, Ruan Chi, Zhenyue Zhang, Yaoyang Ruan, Zhengyan He

Weathered crust elution-deposited rare earth ore is a specific rare earth resource in China that is rich in middle and heavy rare earths. From surface to bottom, the weathered crust elution-deposit rare earth ores can be divided into humic layer, completely weathered layer, partly weathered layer, and bedrock. The exchangeable rare earth ions mainly exist in the completely weathered layer and partly weathered layer, and the exchangeable aluminum ions mainly exist in the humic layer. A novel solution injection method for use in the in-situ leaching technology of weathered crust elution-deposit rare earth ores was put forward based on the different distributions of RE3+ and Al3+ in the four layers. Avoiding the humic layer, only the completely weathered layer and partly weathered layer were leached by controlling the height of the leaching solution liquid level. In this way aluminum, the primary impurity in the RE leaching solution, can be decreased and the purity of the RE product can be improved. Meanwhile, the choices of available leaching reagents were broadened and the possibility of landslide disasters could be reduced.

Jan 1, 2014

By Dwayne D. Tannant

This paper presents a new mining concept for oil sands called ?hydraulic underground mining of oil sands? or HUMOS. While this mining method is still at the conceptual stage it has great promise to allow extraction of bitumen from areas that are currently uneconomical or technically infeasible using surface mining or steam assisted gravity drainage. HUMOS is founded on a combination of recently proven technologies such as directional drilling, water jet cutting of oil sands, slurry transportation, cold water extraction of bitumen, and thickened tailings. One key component in the mining concept is the caving of oil sands and the creation of an underground cavern. Scaled-down physical models will be designed and built to demonstrate water jet cutting, cave development, and insitu primary bitumen separation. These will be used as a 'proof of concept'. On-going research will establish and prioritize issues that need to be resolved, outline key areas where further research is needed, foster establishment of research teams to divide and conquer the important questions, and create framework for future coordinated research efforts.

May 1, 2001

By Brent Robertson

Failure to meet quality objectives during the execution of any industrial project has lasting negative impacts on facility life cycle performance. Cost overruns, schedule delays, and rework are characteristics of project quality issues that arise during the project. Commissioning and start-up problems, low production, production bottlenecks, breakdowns and the necessity for operational work-arounds are characteristics of project quality issues that appear after project completion. Risks such as production facility downtime, shortened equipment life, and potential HSE violations must be clearly identified and addressed during project planning phases. Appropriate Quality Assurance (QA) and Quality Control (QC) focus must be placed on identified high-risk areas. In order to be effective, quality systems must be flexible, non-confrontational, consistent, and adaptable to projects of any size ? from capital mega-projects to small maintenance projects. All project participants must be aligned in how they are approaching quality and the difference between QA and QC must be clear to everyone on the project. Emphasis must be placed on QA activities to minimize project cost, reduce rework, manage change, and reduce the production facility operational risk. QA is focused on the work processes used to generate the design and confirming that the processes are present and being followed. Issues in the work processes guarantee that the output drawings and specifications will be less than optimal. The identification and monitoring of quality-critical processes provides a focus for QA activities. QC activities are then used to generate proof that the project was implemented correctly and become a key part of the turnover.

Nov 1, 2011

In-Country Business Development Agenda ?Siting/Permitting/Operational Planning ?Securing, maintaining, enhancing social license to operate ?Biodiversity conservation and ecosystem services ?IFC Performance Standards ?Environmental, Social, Risk Governance (ESG) ?Climate change plan

Aug 1, 2013