Search Documents

By Li Chongyang, Liu Baolan, Jia Xiaolin, Li Suping

An Al/Al2O3 gradient coating applied on a heat-resistant stainless steel was prepared through a slurry process by using aluminum and ?-Al2O3 powders as the transition filler material, alpha alumina as the surface coating material, aluminum dihydrogen phosphate as the binder, and sodium molybdate as the corrosion inhibitor. The effects of heat treatment temperature, adhesive/filler ratio and ?-Al2O3 content on the bonding strength, microhardness and thermal shock resistance were investigated. The crystal phase and microstructure were characterized by XRD and SEM. The results indicated that the composition of the coating changed continuously from surface to coating-substrate interface. The coating could offer high bonding strength and good thermal shock resistance when heat treated at 700°C.

Jan 1, 2010

By A. G. Pentland

PROSPECTING is popularly supposed to be surrounded with an air of romance and adventure. The word 'prospecting' brings to mind high mountains, northern lakes, and aeroplanes. A note of urgency has been added to this by the war, particularly in the case of strategic, minerals. Prospecting for strategic minerals in a modern mine in full production, although it may Jack the romance of travel in little-known places, has the advantage of having all the necessary machinery at hand and ready to go into action at a moment's notice. HISTORY Tin was discovered in the Sullivan ore in 1925, when a white streak was noticed on a pilot table which was being used to check the amount of galena in the tailing. The mineral which made up this streak was identified as cassiterite. The amount of tin in the ore is so small that, while of scientific interest, it was considered to be of very little economic importance. Nevertheless, several attempts were made to learn something of the occurrence during times when other work was nor pressing. These studies were dropped when anything came up that seemed more important.

Jan 1, 1943

By Hans Lundberg

During the last few years, geophysical methods have been introduced to aid mining geologists and mining engineers in locating mineral deposits. These methods have been developed as the result of investigations of various physical characters of minerals and rocks. In prospecting for ore-bodies, electrical methods have proved most successful. These methods are based on the great differences in electrical properties, and especially in conductivity, between ore minerals and rock minerals. The electrical resistance of the common minerals, rocks, and ores in ohms per cubic céntimeter is given in the following table: [ ] The first attempts at electrical prospecting were based on observing currents of polarization around certain ore bodies, which currents it was possible to measure. This method has been developed by Prof. Schlumberger and has been utilized by him successfully. He is represented on this continent by Mr. Sherwin Kelly, who has successfully operated the method here.

Jan 1, 1926

"Batch flotation testwork demonstrated that a low-grade chromite ore from Bird River, Manitoba, was best floated at pH 2 using Armac C (coco amine acetate) collector and sulphuric acid as pH modifier. A grind of 100% minus 150 um was necessary for liberation, and flotation selectivity was greatly enhanced by prior desliming. A concentrate analyzing 24.2% Cr203 with a recovery of 90.2% was obtained, after three cleaning stages, from ore grading 6.05% Cr203. Total rougher collector concentration was 500 g/t and cleaner collector concentration 380 g/t. Similar grade and recovery were obtained during the pitot-plant evalualion, when a concentrate analy zing 22.3% Cr203 with a recovery of 93% (based on deslimed feed) was obtained for a total collector addition of 630 g/t.Selective flotation in a region of positive surf ace charge implies anionic activation, and a possible flotation mechanism is suggested.IntroductionIn an earlier study(1) of the beneficiation of chromite ore from Bird River, Manitoba, several methods of beneficiation were explored. These included ore sorting, heavy-media separation, and gravity concentration with flotation using Armac C (coco amine acetate) collector at pH 2, and sulphuric acid as pH modifier. Because flotation was not fully evaluated, a laboratory study was undertaken to determine the optimum parameters of chromite flotation. Optimization of parameters was established first on a laboratory scale followed by confirmation a t the pilot -plant level. Flotation of chromite using Armac C and sulphuric acid as a pH modifier has been reported as being selective for low-grade chromite ores(2)."

Jan 1, 1990

By R. Niechcial

As populations grow and industry expands, the limited fresh water resources available are increasingly under stress. This situation creates conflict between communities and industry; and the sustainability of both is threatened. The symbiotic relationship between community and industry highlights the need to develop innovative solutions to these water shortages. The sea may hold the key to providing the resource to permit the development of industry, the sustainability of communities, and the protection of the dwindling legacy water resources around the world. Desalination technologies have developed to where it is now economically viable to create industrial and potable water quality from seawater. Nowhere is this development more important than in the arid region of Northern Chile, where high copper prices have encouraged a boom in mine development.

Jan 1, 2007

By F. J. West

This paper deals with Jones & Laughlin Steel Corporation's new Adams mine, near Kirkland Lake, Ontario. After a brief discussion of ore structure, type, reserve tonnages, etc., the main body of the paper discusses the establishment of an open-pit limit based on economic considerations. The method used by J & L to arrive at an economically sound open-pit boundary its outlined fully. Physical limitations to open-pit boundaries are mentioned briefly. The paper concludes with a few remarks on the mining equipment in use and on its productivity

Jan 1, 1966

By Oscar F. Tangel

This paper outlines Canada's current status in world iron ore markets, and evaluates t he prospects for the future. Estimates for the production, export and consumption of iron ore are given. Canada's major market will continue to be the United States, with the European Common Market countries, Japan and the United Kingdom also forming important outlets. The advantages held by Canada's major competitors in these latter three market areas are briefly discussed

Feb 1, 1966

By Oscar F. Tangel

This paper outlines Canada's current status in world iron ore markets, and evaluates the prospects for the future. Estimates for the production, export and consumption of iron ore are given. Canada's major market will continue to be the United States, with the European Common Market countries, Japan and the United Kingdom also forming important outlets. The advantages held by Canada's major competitors in these latter three market areas are briefly discussed.

Jan 1, 1966

By A. E. Dyment

In formulating an explosive for any specific set of conditions, various factors must be taken into consideration. Is it to be subjected to water or moisture? .If so, it must be designed to have an inherent ability to resist water. Is it to be used in confined spaces underground, where ventilation is limited? If it is, it must possess qualities enabling it to form, upon explosion, the minimum quantity of noxious gases, such as carbon monoxide or oxides of nitrogen. Is it for use where low temperatures may possibly prevail? If so, it must be capable of resisting such temperatures without freezing. Is it for use where dust or inflammable gases may be present? If it is, then it must be so formulated as to produce, upon detonation, a flame of the lowest possible temperature and the shortest possible duration, in order to lessen the chance of ignition of such gas or dust. This is actually the essential property of a permitted explosive, and it is undoubtedly the most important characteristic of an explosive which is to be used in gassy or closed-light mines. This being the quality that distinguishes permitted explosives from other types, it is interesting to investigate the ways and means by which the low-flame-temperature characteristic is obtained . Generally speaking, such explosives are so designed as to contain comparatively small quantities of nitroglycerin and relatively large quantities of the strength-producing salt, ammonium nitrate. This ingredient does not develop as high a temperature upon explosion as does nitroglycerin, so its presence, in large measure, in place of nitroglycerin results in an explosive which has an inherent low-flame-temperature characteristic, as opposed to one which is .made up largely of nitroglycerin, which would ordinarily be in the high-flame-temperature class. Additions are also made of flame-quenching salts such as sodium chloride, ammonium chloride, and up to a certain limiting percentage of sodium nitrate. These salts, with the exception of the last, do not ordinarily take an active part in the explosive reaction, being present primarily to absorb heat liberated by the reacting ingredients.

Jan 1, 1947

By Karl J. C. Harries

This paper looks briefly at some of the agreements and types of royalties that may be met during exploration activities, but does not go into details relating to them. Agreements can either make or break a deal or relationship. A well drafted, comprehensive and fair agreement can create good relations and trust among the parties and will go a long way towards making a deal work. In the best of all worlds the agreement will be put away and not need to be referred to after it has been signed (but it will be there if needed to sort out potential problems). On the other hand, a poorly drafted agreement or one that is inappropriate to the circumstances or unfair to one of the parties can break a deal and end up with the parties facing each other in that expensive, unproductive and time-consuming occupation ? a lawsuit. Accordingly, it is advisable to involve professional advisers with any agreement. The straightforward one may involve no more that a read through whereas the more complex agreement will require considerable involvement. There is, however, one rule for every explorationist to remember: a professional adviser is only an adviser. His responsibility is to make sure that you have the necessary information to make a reasoned decision but the decision is yours, not the adviser?s. It is your deal, you are going to have to live with it, and it is inappropriate for an adviser to introduce new concepts or amend negotiated ones without your specific instructions. Mineral exploration agreements, although basically option, acquisition and joint participation agreements, come in all the shapes and forms, appropriate to give effect to the endless variety of deals negotiated by the ever-active minds of explorationists. You will note the reference to "joint participation agreements" rather than "joint venture agreements". The latter term was purposely avoided because, with the current activity of explorationists from common law jurisdictions in civil law jurisdictions, it has become necessary for the explorationist to become familiar with corporations and shareholders agreements. As most of you are no doubt aware, under the civil law system a joint venture is normally not recognized as a legal entity and, therefore, joint participation in projects is usually by way of corporations.

May 1, 2003

By Mohamed Sassi, I. Kolo, R. L. Sousa, R. K. Abu Al-Rub, Manhal Sirat

"Fractures induced by folds are pivotal in hydrocarbon exploration, ground water transport and harnessing of geothermal energy. This is because of the need to predict and understand fracture propagation in reservoirs which have folded rock formations. Despite its prominence, there is a lack of reliable numerical models for simulating fractures resulting from rock folding. This is partially due to the difficulty involved in fracture modelling. As a contribution to fold-fracture modelling, this work applies a coupled plasticity-damage model to rock fracturing and anticlinal folds. Parametric studies on a single folded layer give insight into the fold formation and behaviour. The anisotropic continuum damage model which considers both tension and compression is formulated using the power damage evolution law. For ease in formulation, strain equivalence hypothesis is adopted whereby the strain is the same for both damaged and undamaged configurations. Lubliner plasticity yield criterion is adopted for plastic deformation. The model is coded in Abaqus user subroutine UMAT and is applicable to quasi-brittle materials.INTRODUCTIONThe understanding of fractures in the earth’s crust helps in the prediction, evaluation and characterization of fractured reservoirs, whether they are petroleum, geothermal or underground water reservoirs. This is partly because reservoir permeability and stability are dependent on fracture properties (Nelson, 2001). To achieve this, various approaches have been developed to analyze reservoir rock fractures. These could be grouped into (a) discrete approaches – where the rock mass is represented by a finite number of well-defined components and (b) continuum approaches – where the mathematical assumption of an infinitesimal element is made (Jing, 2003). Ivanova (Ivanova, 1998) comprehensively studied fracture systems in nature and highlighted folds as one of the major geologic settings that produce fractures. Naturally occurring folds in reservoirs sometimes compound fracture analysis. It might not be clear whether the fractures formed before, during or after rock folding. Fractures formed during the folding process are expected to show stress orientations related to folding and are thus of primary concern in rock folding simulation. It could be argued that there are no numerical models that as"

Jan 1, 2015

By Ralph L. Rutherford

Introduction During the past twenty-five years we have seen considerable exploration for oil on the plains of southern and east-central Alberta. This exploration has to some extent gone on in cycles, with periodic starts, stops, and occasionally some reversals. Each major attempt is usually supplemented by the application of some new method of exploration and, following each period of exploration, drilling tests are made. Whereas oil-bearing horizons are the ultimate objective of these explorations, the preliminary investigation frequently aims at a discovery of structure based on the long accepted belief that accumulations of oil and gas are to a marked degree structurally controlled. At the inception of this general exploration for oil, it was natural that attention should be directed to areas where there was surface evidence of deformation of the underlying strata, but, as the programme progressed, it was found that these surface manifestations of structure were often deceptive when attempts were made to project them to depth, to involve the deeper strata. Drilling of test wells was the only satisfactory method of obtaining exact information.

Jan 1, 1946

By C. Robinson

The Diavik Diamond Mine is located in one of the most remote and forbidding places in the world, 220 kilometres south of the Arctic Circle and on the bed of a vast northern lake, Lac de Gras. A single road, built out of ice and crossing frozen lakes, connects the mine with other operations and Yellowknife, the capital of the Canada's Northwest Territories. Diamonds were first discovered in the Lac de Gras region in the early 1990s, and construction of the Diavik Diamond Mine was completed in 2003. Diavik currently mines three kimberlite pipes. Open pit mining has now concluded and all three pipes are mined using underground mining methods. In early 2010, Diavik began mining and processing initial ore from its new underground mine; underground mining operations are expected to continue beyond 2020. The initial mine ventilation system was an exhausting (pull) system with fresh air supplied by a fresh air raise and a main ramp. Return air was exhausted via two raises and a secondary ramp. The system had a total flow capacity approximating 401-411 m3/s. With planned increased production and with changes in mining method, it has been proposed to change the mine ventilation system to a positive (forcing) ventilation system in order to meet projected increases in flow requirements of 566-708 m3/s. Extensive engineering work was developed in order to successfully achieve the changes in system configuration. In the proposed configuration, the main ramp is in an exhaust configuration and exhaust raises are converted to fresh air raise. A number of system implementation options were investigated and phased plans for system execution have been developed. The proposed changes to the ventilation system are substantial and involve extensive construction work. Work was commenced in 2011, each planned phase has been successfully completed to date, and system changes continue today in order to achieve complete system flow reversal and increased flow distribution. This paper details the design of the modified ventilation system and commissioning work which will allow the mine to meet its future production targets.

Aug 1, 2013

By J. W. Matousek

"Computer modeling of smelting processes requires internally consistent equations for calculating the compositions of mattes and slags. That is, the sum of the calculated assays must total 100%. One set of equations that satisfies this requirement for copper produced under oxidizing conditions (pSO2>one atmosphere pressure) is given by the following:%[Fe] = 62.0 – 0.775%[Cu]%[S] = 28.0 – 0.00125%[Cu]2%[O] = 10.0 – 0.225%[Cu] + 0.00125 %[Cu]2Mattes containing nickel in appreciable quantities do not have the defined “white metal” end point of approximately 80 percent copper and 20 percent sulphur that is found in the copper system during the converting process. The above equations, however, are readily extended to nickel and nickel/copper mattes for any desired end product composition."

Jan 1, 1996

By Christoph Mueller

?Globalization and the impact on mine operations? is one of the themes of the 2003 annual CIM meeting. Global mining business in practice always means to act with local base material resources in order to reach the mining company?s global business goals. On the other hand these operations are characterized by cost pressure and cycling product prices. Driven by actual prices, local product markets and local production cost, one time one mine can be most efficient while under different circumstances another mine will be the most efficient producer for the same customer [PENSWICK, 2001]. Therefor in the future the most profitable mining companies will be those who have permanent ?real-time? control on their actual production cost level. Certain approaches are under way to provide reliable modeling tools for aiding mining companies in highly complex decision finding procedures. A high potential for enhancing efficiency is the integration of all single steps of the mining working chain into a production process structure to make advantage of an optimized flow of material and information through the ?moving ore factory? [WIGDÉN, 2001]. Crucial to all these activities is the ability of getting reliable, just-in-time information from the entire mining production chain. As modern mining machinery today is controlled electronically and even already operated autonomously, the theoretical preconditions for the data acquisition is already fulfilled. But up to now, there was no way of cost effectively exchanging the process information with databases, simulation tools and other enterprise level software. Any data exchange problem had to be solved by individual and expensive software development projects. To solve these problems, the International Rock Excavation Data Exchange Standard (IREDES) was launched in 2000 by major players in the industry. The task of this initiative is to define a ?common electronic language? for easy and standardized data exchange between mining machines and central computer systems. As in other industries, this standard is expected to have significant impact on the use of automated equipment. It shall provide easy ways of using multi vendor machine installations in data controlled mining processes. At the same time it reduces cost for individual development of interfaces for all parties involved. The standard?s technical architecture is flexible and open - also for future applications. It uses modern technology enabling easy data exchange with commercial databases as well as open on line networking.

May 1, 2003

By L. Sun

Recently, micro-tubular solid oxide fuel cells (SOFCs) have attracted the attention of many researchers because of their numerous advantages over larger tubular and planar SOFCs. These include excellent thermal shock properties giving rapid startup/shutdown capability, a high volumetric power density compared to larger tubular SOFCs, and reduced sealing problem compared to planar SOFCs. In order to screen cathode materials for micro-tubular SOFCs, the perovskite cathodes were deposited, using a variety of methods, on 10.5 mol % yttria-stabilized zirconia (YSZ) tubes. Their electrochemical properties were then evaluated by using electrochemical impedance spectroscopy and steady-state polarization methods, based on a three electrode configuration, and with the reference electrode position carefully optimized. The oxygen reduction reaction kinetics at the cathode/electrolyte half cell were then investigated in detail.

Jan 1, 2005

By R. A. L. Drew, C. A. Rodríguez González, Caleym W. F.

This work addresses the need of new refractories for copper converters. Technological improvements and environmental regulations for chromium containing refractories have generated this need. Chemical interactions, mechanism of penetration and the effect of oxygen potential and temperature in the system Cu2S-FeS-SiO2-O2 are presented for two refractories: a burned magnesite chrome brick (typically used by the copper industry) and a chrome-free spinel direct bonded brick. The main difference determined in the refractory performance was the blister copper penetration resistance; burned magnesite chrome brick is penetrated while direct bonded brick is not. These results are very promising since blister copper penetration has been reported as the major cause of refractory wear. The results are explained in terms of refractory porosity and wetting characteristics.

Jan 1, 2004

By R. B. Allen, E. E. N. Smith, B. C. MacDonald

"LocationTHE MAIN PROPERTY and townsite of Eldorado Mining & Refining, Limited, Beaverlodge Operation, is on the north shore. of Beaverlodge lake, •about seven miles north of the deserted town of Goldfields on lake Athabasca, and four hundred and ninety air-miles equidistant from Prince Albert, Saskatchewan, and Edmonton, Alberta. Both Eldorado Airlines •and Canadian Pacific Airlines maintain scheduled flights from Edmonton to the 4,000-foot airstrip on the north boundary of the Company property. Bi-weekly flights are made by Saskatchewan Government Airways from Prince Albert. Men and priority freight are flown by Company aircraft direct from Edmonton. From June to-September, when the waterways .are ice-free, freight is carried by barge from the •railhead at McMurray, Alberta, down the Athabasca river to Chipewyan, and across lake Athabasca to• Bushell, the terminal on Black bay, lake Athabasca, a total distance of 265 miles.The Eldorado Operation has been connected by a 12-mile, all-weather highway to Bushell. Where the highway crosses the park-land along the Fredette river, the townsite, Uranium, is under construction to provide services to the uranium-producing district. Spur roads have been built to the Ace, Fay, Eagle, •and Martin mines of the Eldorado operation, and to the properties of Pitch-Ore Uranium Mines, Ltd., and Rix Athabasca Uranium Mines, Ltd."

Jan 1, 1954

By J. Baumbach, H. Bombach, M. Stelter

"Today technical electro-refining processes for copper exclusively use sulfuric acid, for silver refining nitric acid electrolytes are used. Sulfuric acid is characterized by very good chemical and electrochemical stability, good conductivity and low cost. The disadvantages of sulfuric acid are the precipitation of fine-grained cathodes with smooth surfaces only by using additives like glue, thiourea and chloride. In case of silver the electrolyte is electrochemical unstable and bears the risk of the formation of toxic NOx when pH is too low. A second disadvantage is the form of electrodeposition of silver as dendrites with their removal from the bottom of the Möbius cells.This paper reports the results concerning the application of an alternative electrolyte in copper and silver electro-refining. At first the electrolyte was characterized by the determination of current density potential curves. Electrolysis experiments were performed in laboratory scale using technical anodes for copper and synthetic anodes for silver. During the copper tests the solubility of contaminations from the anodes and the amount and chemical composition of the anode slimes were determined. Moreover the influence of current density, electrolyte temperature and the effect of several additives on the precipitation and chemical purity of the cathodes were investigated. In all experiments cell voltage as well as anodic and cathodic polarization was measured and current efficiency and specific energy consumption were calculated. A comparison with the results with those of tests using conventional sulfuric acid electrolyte shows the advantages and disadvantages of both systems, additionally the technical application chances and limitations for the new electrolyte. This electrolyte enables the precipitation of smooth copper cathodes with low silver and sulfur concentrations even at lower temperatures without any additive. For silver refining the electrodeposition of compact silver sheets is possible, that can be stripped comparable to those in copper electro-refining."

Jan 1, 2016

By Fathi Habashi, Ernesto Bourricaudy, Fouad Kamaleddine

Ilmenite occurs in black sand at the mouth of great rivers as in India, or as massive deposits like in Quebec Province in Canada. It is unsuitable for processing into pigment or for metal production because of its high iron content and its low grade. Pyrometallurgical and hydrometallurgical methods have been developed to cope with this problem which resulted in the production of two commercial products that became known as synthetic rutile and Sorelslag. Attempts are also underway to produce TiO2 pigment directly from ilmenite. This report presents a newly developed process called the Magpie process, which enables the production of high-grade synthetic rutile (over 95% TiO2) from low grade ilmenite (10-12% TiO2). Naturally, if such process is applied for low-grade ore it can be applied with advantage to high grade material as well.

Jan 1, 2014