Search Documents

By C. Lara-Valenzuela, R. Perez-Garibay, F. López-Saucedo, A. Uribe-Salas, L. Magallanes-Hernandez

A relationship between gas dispersion parameters, namely gas rate (Jg), gas holdup (Eg), average bubble size (db) and bubble surface area flux (Sb), with the metallurgical performance (e.g., grade and recovery) has been established.. Results of eleven columns operating at five concentrators of Grupo Pefioles (Mexico), ranging between 1.52 to 3.35 min diameter and performing in the cleaning stages of lead and zinc circuits, are presented and discussed. The results showed that the effect of gas dispersion parameters was consistent and that both, Sb and Eg, correlate well with recovery particularly when the influence of feed pulp density is also considered.

Jan 1, 2009

By Elizabeth Edwards, Radhakrishnan Mahadevan, Vladimiros G. Papangelakis, Srinath Garg, Kurtis Judd

Mineralogical characterization of the tailings showed the deportment of Ni to be similar in the Vale and Glencore tailings, with 60% of the total Ni locked in pyrrhotite, and the balance 40% associated with pentlandite. The overall Ni dissolution was correlated with the individual dissolution extents of pyrrhotite and pentlandite as functions of four leaching regimes: ‘anoxic acid’ (with and without pH control), ‘oxic acid’ (oxygen sparging), ‘oxic acid’ (air sparging), and ‘oxic ferric’ (air sparging). The results showed that the maximum Ni dissolution was obtained during the pH controlled oxic acid leach with oxygen sparging at pH 1.5, while the anoxic acid leach at pH 1.5 resulted in minimum Ni dissolution (10–15%) from pyrrhotite. An overall Ni mass balance showed that pyrrhotite and pentlandite dissolve simultaneously in the presence of Fe(III) and oxygen, in contrast to the preferential dissolution of pyrrhotite in the absence of Fe(III). Sulphur mass balances revealed that the yield of elemental sulphur is maximized (65%) during the oxic Fe(III) leach at pH 0.6. Furthermore, the kinetics of Ni leaching and elemental sulphur formation from pyrrhotite tailings leached with ferric sulphate between 55–80°C was investigated at constant oxidation-reduction potential. Elemental sulphur yield increased with increasing temperature, but no observable trend could be linked to ferric or ferrous ion concentration.

Jan 1, 2017

By L. S. Brooks

TIMBER HANDLING presents a problem for any mine where appreciable amounts are used. This problem is accentuated where the shaft compartments are too small to allow a loaded timber truck to be lowered in the mine cage. When Normetal Mining Corporation, Limited, found it necessary to resort to square-set mining it faced this problem of getting large quantities of timber down a shaft that was also required for hoisting ore. A 'timber car' that could be suspended under the cage was developed to overcome this difficulty. Production started at the Normetal mine in 1937, at the rate of 250 tons per day. In 1938 a winze, known as No. 3 shaft, was sunk from the 800-foot level ?to the 1,385-foot level. This was later raised to surface and then deepened to 3,275 feet in three stages and became the main production shaft. The portion of the mine below the 3,070-foot level is serviced by a winze, locally referred to as No. 4 shaft, which has been developed for stoping down to the 3,990-foot level and which has been deepened to the 5,365-foot level. No. 3 shaft has two hoisting compartments, each 4 ft. 6 in. by 5 ft. 0 in. inside the timbers, through which the ?ore must be hoisted and timber and supplies lowered.

Jan 1, 1956

By Finch. J. A., C. Perez, J. M. Ortiz, G. Cortes, A. B. Yañiez, F. Coddou, P. Morales, H. Elgueta

A campaign to perform characterization tests in a TankCell®-300 flotation cell installed at Chuquicamata Codelco's concentrator was conducted. The campaign included integrated gas dispersion measurements (gas velocity radial mapping and single point gas holdup and bubble size) and determination of frother concentration. Cell streams were sampled to assess metallurgical performance at the same time. The experimental program was designed to establish the bubble surface area flux operating range and its effect on performance, and the effect of using longer residence times and of a device designed to enhance mixing in the collection zone (FlowBooster(TM)). The gas dispersion results and their relationship to metallurgical performance are discussed.

Jan 1, 2009

By A. F. Laurin, A. L. Dorr

"Because of its wide areal extent, its numerous lithological facies and its high degree of metamorphism, the Quebec portion of the Grenville province has only partly been explored and prospected. Rock types that are economically among the most interesting in the Grenville are those of mafic and ultramafic compositions, because of their great potential for coppernickel and chromium-platinum. The peculiar mode of occurrence and the distribution of these igneous masses in which copper-nickel mineralization is known to occur indicate' two common geological features: (1) aerial photographs and/or topographic maps strongly' suggest close spatial (and possibly temporal and genetic) association of most of these mineralized mafic and ultramafic intrusions with circular structures; (2) when plotted on a large-scale map comprising the Quebec portion of the Grenville, these circular structures fall along two lines which could correspond to major tectonic features. Even though the genetic links among the mineralized mafic-ultramafic masses, the circular structures and the linear features are not yet fully understood, their associations are believed to be empirically valid and should therefore be used as geological tools by those interested in exploring the Grenville for copper-nickel and possibly chromium-platinum deposits. It should be noted that these mafic and ultramafic bodies do not appear to be spatially related to anorthosite complexes."

Jan 1, 1971

The reliability of mining systems is generally low due to their harsh working conditions. Currently, efforts for improving mining system reliability are often made in isolation. This practice could substantially limit the effectiveness of the efforts on overall reliability improvement of the mining system. To enhance the overall reliability of mining systems, an integrated improvement approach is necessary. In this paper, we developed a framework for integrated mining system reliability improvement to address this issue. In this framework, there are five major components including data integration, business process integration, hardware integration, software integration, and analysis/decision integration, but we only focus on the integrated reliability analysis which is important to the analysis/decision integration. The reliability analysis considers the interactions between machines, and the impacts of design, operation, maintenance, automation and working environment on the overall system reliability. These multiple interactions present a big challenge to accurate reliability prediction. In this paper, we for the first time systematically investigated integrated reliability analysis approaches for dealing with this challenge using novel models and methods, including covariate hazard models, intelligent reliability prediction approach, and complex system modeling methods. While these models and methods have found some successful applications in other industries, they in general have not been effectively used for the reliability analysis of mining systems. Our study results show that the system integration approach is applicable to mining systems and can be used for developing a computer aided integration system for the implementation of the integrated reliability improvement approach.

Aug 1, 2013

By Tim Gitzel

Thank you for your introduction, and thank you to the CIM for inviting me to make a presentation to you today. This is my first opportunity to report to you on the status of the Canadian uranium industry and I am pleased to tell you that the industry is in good shape, and well positioned for the future. As you will no doubt be aware, Saskatchewan benefits from the world?s largest known highgrade deposits of uranium as well as from a high level of provincial, public and northern community support. It is within this unique combination of geology and community that our industry operates. Uranium markets have been extremely competitive for a number of years for several reasons. First, deregulation in the nuclear electric power industry has tended to encourage fuel buyers to use up their large inventories built up at a time when rapidly increasing demand was anticipated. Second, alternate sources from surplus commercial stocks, military materials and reprocessed fuel have presented a major additional source of uranium supply. Today, these secondary supplies are meeting about half of uranium reactor feed requirements. Canada (that is, Saskatchewan) is the world?s largest ?natural? uranium producer with about a third of the global production. Saskatchewan?s mines produced more than 30 million pounds of yellowcake in 2002. Despite low prices, steady demand for uranium will continue. In fact, an increase in world uranium production in 2002 helped feed a more than 3 per cent increase in reactor fuel demand. Low cost production is important for surviving low market prices, but investments are based on longer-term strategies rather than simply responding to market cycles. Cost is not the only issue. In these times of increasing regulatory and public scrutiny we must continue to earn the trust of our stakeholders by adopting the highest standards and staying on the leading edge of technical, social and environmental developments. Managing these issues is as important as traditional concerns of ore grade and cost of production. The last two decades of the 20th century saw the Province of Saskatchewan rise to prominence as the leader in uranium production from facilities, which were at the time deemed world class. These facilities are now either at - or nearing - the end of their production years. We are now bringing on new facilities that will position Saskatchewan to remain the world leader in uranium production for many years to come.

May 1, 2003

By Theophile Yameogo

The rock mechanics literature has documented the challenges, failures and successes of tunneling through weak rocks. Cases usually deal with low RMR rock masses or high stresses in a fractured zone. With the combination of 5MPa water pressure, 14 RMR ground with clay infillings and ground freeze walls, the case of the 510-8225N development drift at McArthur River is certainly much more challenging, especially when high grade uranium production is at stake. The article explains the excavation and the ground control techniques that were used to overcome the challenges of development at the Unconformity in the Athabasca Basin.

Aug 1, 2010

By John L. Rich

A New Field for the Mining Industry A new field for the mining industry is in prospect. This is the recovery of the petroleum which has been left in the ground in the older oil fields whose yield has declined until they are no longer profitable to operate in the ordinary way. The fact that an oil field has reached the economic limit for operation by pumping does not necessarily 'mean that the oil has ? been exhausted. In many such cases not over one-fifth, or even one-tenth, of the total oil content of the field may have been taken out when this stage has been reached. This means that there exists a large reserve of oil which can be recovered by whatever process best takes advantage of the natural conditions under which the oil occurs. Mine drainage is one of the processes by which this oil may be recovered. Its relative importance will depend partly on the ingenuity and wide-awakeness of mining engineers, and on mining capital. The opportunity is undoubtedly at hand. In order that we may be in a position to judge the possible advantages of mining methods for the recovery of this oil, I have reviewed, on the following pages, the methods now in use, and have discussed the physical conditions of the reservoir rocks in which the oil is found, and the suitability of the various recovery processes, in use or proposed, in the light of these reservoir conditions.

Jan 1, 1927

By Wei Wei

Mining induced ground movement and/or stress redistribution could cause ground instability issues. This is particularly true when the extraction of large stopes is done with one or two large production blasts. Often enough, it is the nearby mine development like haulage drifts and cross cuts that are influenced the most by production blasts. Proper and timely mitigation of ground control issues due to stress redistribution is required. This is usually done by drift rehabilitation involving the installation of secondary support system in the affected areas of the mine development which include; slashing, wire mesh, and in some cases the use of shotcrete liners. It is imperative that such rehabilitation be implemented to the mine infrastructure in a timely manner in order to avoid aggravated ground control problems and production delays. If the real time performance of the support system is captured, it would be possible to determine the timing for rehabilitation job. Birchtree Mine in Thompson, at the Vale Manitoba Operation, has begun mining the 84 Deep Orebody. One of the identified risks is the stability of the crusher room under mining induced stress redistribution. It is proposed to use the U-Cell technology to monitor the primary support system performance (rebar bolts and extension bolts) and monitor the real time performances of the bolt axial loads. The U-Cell technology is a 7-inch long, coupler load cell that is screwed onto the threaded portion of a rock bolt prior to installation. Rehabilitation in the vicinity of the crusher area where U-Cells are installed is recommended when the bolts have reached 70% of their yielding capacity. Catastrophic ground failure can be avoided by adding secondary support in a timely fashion. This paper presents a case study at Birchtree Mine in Thompson Manitoba, where the performance of primary ground support system is monitored and recorded during production.

Jun 1, 2012

By T. G. Sitharam, Resmi Sebastian

"Wave propagation studies across jointed rocks have significance in the fields of rock mechanics and geophysics. The passage of a seismic wave induces strains in rocks and often, these strains are of low magnitudes except at the vicinity of source. These low magnitude strains are generally in the elastic range and hence elastic constants necessary for the design and analysis of strength of rock mass, can be derived from wave velocities. Measurement of travel time velocities and measurement of resonance frequencies are the two methods usually adopted for obtaining wave propagation velocities.Resonant column apparatus measures wave velocities from the resonant frequencies obtained during testing. Depending on the type vibration applied, torsional or flexural, shear and compression wave velocities are secured. By varying the amplitude of vibrations applied, various strain levels can be introduced and corresponding resonant frequencies and wave velocities can be calculated. The resonant column experiments were performed on a model material, hardened Plaster of Paris (POP) samples, in laboratory. The paper explains the preparation of samples and the working mechanism of resonant column apparatus along with the estimation of wave velocity from resonant frequency. The numerical simulation of resonant column apparatus using distinct element method and its validation with the experimental results are presented in the paper.A distinct element code is usually used to simulate the movement of materials with intersecting discontinuities. Finite rotations and displacements of individual blocks representing the material are permitted and new contacts between the blocks are identified as the calculation progresses. Three dimensional Distinct Element Code (3DEC), the software intended for the numerical simulation of rock engineering projects, can well simulate the behavior of jointed rocks under static and dynamic loading conditions. The numerical simulation of resonant column apparatus has been performed with 3DEC considering its efficiency in modeling jointed rocks.The numerical modeling of the resonant column apparatus with application of torsional and flexural vibrations to the sample is elaborated in the paper. The response of samples to a range of frequencies is obtained and the frequency that induces maximum displacement in the sample is measured as the resonant frequency, for any particular strain level. The displacements measured at various points of the sample during application of vibrations are compared and presented. The numerical modeling of resonant column apparatus with an intact sample (without joint) and a sample with a joint incorporated are explained at a particular strain level. The resonant frequencies obtained from laboratory experiments and numerical simulations are compared and illustrated. It has been found that resonant frequencies obtained using numerical and laboratory experiments are in good comparison and can be extended for various strain levels and sample conditions."

Jan 1, 2015

By A. J. A. Janse

The Argyle diamond mine is located in the Kimberley region in the northern part of Western Australia at approximately 16°43'S, 128°23'E in subtropical bush/shrub savannah. The 46 ha (113 acres) pipe is situated in the Halls Creek mobile zone, which was cratonized about 1800 Ma ago and adjoins the Kimberley Block, a plateau upheld by Early to Middle Proterozoic rocks underlain by presumably Archean basement. The crater and upper pipe zones of the diatreme have been preserved within tilted and faulted strata of Middle to Late Proterozoic age. Its age of intrusion is about 1178 Ma. The diatreme rock is not kimberlite but olivine lamproite which was not recognized as a primary diamond host rock until 1978. The Kalumburu Joint Venture, a syndicate of local and overseas mining companies, started in 1972 to prospect the Kimberley Block with a modest annual prospecting budget of $125,000. Annual expenditure doubled each year and reached $1 million in 1975 after which CRA took over management of the newly-formed Ashton Joint Venture with an annual expenditure of $2 million (all figures are in current US dollars). The Argyle diatreme was found near the end of the eighth field season and after a total expenditure of $12 million. Annual production is about 34 million carats which places Australia as the world's number one diamond-producing country, although, because of the low value per carat, it is number four in terms of total annual value. The global cost required for a major diamond mine is between $300 and $400 million, with a discovery every 10 to 12 years. Because Canada contains large areas of prospective platform rocks underlain by Archean basement it is likely that a major diamond deposit does exist there. It is probable that it will be found before the end of this decade and exploration expenditure may be in the order of $100 million.

Jan 1, 1992

By W. W. Weber

"The Mine property comprises some 700 acres in ranges VI and VII, Barraute township, about thirty-seven miles due north of Val d'Or in northwestern Quebec.The transformation of a small farming community into the youngest and largest zinc producer in eastern Canada began late in the autumn of 1950. At this time, a geological survey party of the Quebec Department of Mines discovered sphalerite-pyrite mineralization in a strong regional shear structure crossing range VII of Barraute township. Diamond drilling commenced in November 1950, and by June 1951 a total of more than 63,000 feet of drilling, at fifty-foot intervals, had explored an ore zone 2,500 feet in length and 102 feet in average width to a depth of 700 feet, the deepest ore intersection.Production started late in 1952, and is at present in excess of 4,000 tons per day. Production in 1954 of77,790, 166 lbs. of zinc and 989,610 oz. of silver, from 1,525,284 tons of ore, makes this mine the largest zinc producer in eastern Canada.General GeologyAll the consolidated rocks of the area are Precambrian, and most of them are volcanic. They consist mainly of subsiliceous Javas, with smaller amounts of siliceous to intermediate lavas and pyroclastic rocks. The lavas have been intruded contemporaneously by many sill-like bodies of coarser-grained diorite and gabbro. There are no sedimentary rocks within ten miles of the mine.A period of major folding and faulting was followed by intrusion of granite. The volcanic rocks have been compressed into isoclinal folds trending roughly east-west, and the granitic batholiths also show a rude lineal alignment in the same direction. The granitic masses vary consider-ably in composition, ranging from the potassic LaCorne granite, ten miles south of the mine, to the sodic Duverny mass, ten miles west. In addition there is a variation from a general granitic core to dioritic and gabbroic phases on the margins and in satellitic intrusions."

Jan 1, 1949

By Luis Bergh, Juan Olivares, Juan Durán, Juan Yianatos

"In the last decades heuristic approaches based on logic rules have been one favored tool to control flotation units and plants on top of distributed control systems. Fundamental knowledge on flotation processes, expressed in reliable models, and programs to assure the quality of the information, contained in available measurements, are still insufficient to develop robust predictive control strategies. In this paper the idea of using simplified models, when a known disturbance is coming into the process, is explored. As a first approach, the set points of the froth depth and air flow rate controllers are estimated based on this model. Since these target predictions are only approximate, a conventional feedback expert system, based on logic rules, continues the task of calculating the set points of the distributed controllers, in order to decrease the gap between actual and desirable metallurgical targets. This combined actions permitted a fast response of the process to change the operation of the circuit when a measured disturbance is detected. This control system was implemented and experimentally evaluated in a pilot rougher flotation circuit, with three pneumatic cells, with froth depth and air flow rate controllers in each cell. Since the circuit is operated for the air-water system, a phenomenological model, with parameters estimated from industrial data, is fed on-line with real operating variables and virtual values, characterizing the feed (grades, solids%, particle size distribution), in order to predict the metallurgical targets (recovery and concentrate grade). Several cases are discussed showing the benefits of this control system and the possible improvements to work on. INTRODUCTIONToday, large size mechanical flotation cells of 100 to 300 m3 are used in rougher operation in different flotation industrial plants, in Chile and worldwide. However, in spite of the advances in fundamental research and the notable growing in equipment size, with more complete instrumentation systems, there are still a lack of reliable data for industrial flotation modeling and simulation to advance in better control systems design."

Jan 1, 2016

By G. Vibert Douglas

It has long been recognized that there are considerable difficulties connected with the physical and chemical explanation of shoots of ore. The literature of Mining Geology has frequent references to this subject; but the reasons given for the actual location of primary ore-shoots have been very tentative. In practice, the geologist or miner depends to a great extent on sampling and assaying to determine the boundaries of profitable ore within the mineralized zone. An ore-shoot is a portion of a mineralized zone which has a sufficient concentration of valuable minerals to make it ore. Ore deposits have been classified according to many schemes. There are classifications based on morphology and on genesis. However, it is also possible to classify hypo-gene hydrothermal ore-bodies in terms of ore-shoots or vice versa. A.-Ore-deposits in which the whole of the mineralized zone is ore, which is the same as saying that the ore-shoot extends throughout the mineralized zone. An example of this type of deposit would be the pyritic mineralization of Rio Tinto. B.-The second type would comprise those deposits in which the ore-shoots bear some relation to the geological structure of the area: all deposits in which 'bonanzas' occur in folds in the zone, at the intersection of veins along certain fault (or joint) features and other such controls. There are a great many examples of this type: (a) The Rhodesian copper lodes, where Bancroft and Gray have pointed out the association of the shoots of ore with drag folds. (b) A similar association has been pointed out by Faribault for some of the gold veins of Nova Scotia, e.g., Mount Uniacke. (c) The great bonanza of the Comstock lode in Nevada. C.-Deposits in which the localization of ore has been effected by the chemical character of the wall-rock. Examples of this type are the Fahlbands of Scandinavia, and the 'indicator' deposits of Ballarat, Australia. D.-Lastly, deposits in which there is apparently no structural and no chemical control.

Jan 1, 1934

By Tom Shumka

All mineral processing facilities that use girth gear driven mills need to inspect the gear teeth on a routine basis, whether it is every six months or every three years. The inspection frequency depends upon gear tooth condition, and the objective is to ensure operational integrity of the gear teeth. Conventional methods such as magnetic particle testing, visual inspection, or dye penetrant examinations rely heavily on interpretation. At best, these techniques can determine whether a defect exists, but are unable to provide information on defect severity. This paper describes the use of combined Eddy Current Array (ECA) and Alternating Current Field Measurement (ACFM) to provide a complete survey of all surface breaking indications on the whole gear tooth depth. This method accurately determines the size, length and depth of any cracks found on the surface.

Jan 1, 2012

By P. G. West-Sells

At Barrick's Zaldivar Copper Mine in Chile, the addition of sulfuric acid to the ore going to heap leaching is a major expense. A process in which a portion of this acid is replaced by elemental sulfur added to the heap has been developed by Barrick and Westcoast Biotech that has the potential for significant cost savings. Initial shake flask tests with plant raffinate solution indicated that oxidation of elemental sulfur by a culture of sulfur-oxidizing bacteria, some indigenous to the Zaldivar heap, showed a significant lag period. This lag period could be reduced by dilution of the raffinate, but dilution would not be economical to implement at Zaldivar. Short (0.75 m) column tests indicated that after the initial lag period, sulfur biooxidation occurred steadily and the acid requirement for obtaining the same copper recovery as the control without sulfur was reduced by as much as 13 kg/t. These tests were followed by taller (5.1 m) column tests that confirmed the reduction in acid consumption, with no negative effect on copper extraction.

Jan 1, 2007

By Bryon Bisiaux, Walter Valery, Sonny Mwansa, George Amonoo, Adrian Dance

"Newmont Ghana Gold Limited’s Ahafo operation have been working with Metso Process Technology & Innovation (PTI) since early 2009 to increase mill throughput from a combination of controlled blasting practices and optimised primary crusher and grinding circuit conditions. For such Mineto-Mill projects, PTI’s methodology is termed Process Integration & Optimisation (PIO).Ahafo operate a SAG mill, ball mill and pebble crusher (SABC) circuit that processes a range of primary ore of varying hardness from different pits which is blended with soft oxide material. The PTI study focussed on ball mill limited material from the Apensu open pit.Following a benchmarking study of all blasting, crushing and grinding practices in January 2009, PTI recommended changes in both blasting and crushing conditions in order to generate a finer feed size to the SAG mill. Additional operating changes in the grinding circuit were recommended.A series of trials were conducted in November 2009 where three blasts were fired using a different blast design (hole diameter and explosive type) in the same area of the Apensu pit as the benchmarked material in January 2009. Top and bottom benches (or flitches) from each blast were sent exclusively to the grinding circuit and the material was tracked using PTI’s SmartTag™ system.The results from the six trials showed a significant increase in primary ore throughput at a reduced blend of oxide material. Ahafo have since standardised on these modified blasting conditions for all Apensu ore zones and have been able to sustain higher throughput compared to historical performance on similar material.This paper summarises the phases of the PIO project, the changes made in operating practices and the outcomes of the blasting trials that validated the predicted increase in mill throughput."

Jan 1, 2012

"The ore currently being milled at Delnite is a high pyrrhotite ore with the gold intimately associated with the pyrrhotite. To get maximum recovery of the gold with the lowest reagent cost, it is necessary to keep the pH as low as possible In the laboratory the best results were obtained with a pH of 10 but in the plant it was found that a pH of 11 was the minimum practical pH. With the n1anual control it was difficult to maintain this figure.The Mines Branch had a conductivity probe (see Fig. 1), developed by Dr. G .G. Eichholz that they wished to try out in plant operation.On June 17, 1963, the probe with all necessary control equipment was installed in the regrind circuit (see Fig. 2) at Delnite Mines. Crushed quick lime is fed at this point but it is also necessary to feed hydrated li1ne at two other points in the cyanide circuit in order to maintain the pH close to 11. 0 throughout the circuit. Only the feeding of the quick lime at the regrind mill was controlled in this test.One thing that concerned me with the operation of the probe was whether the reading on the probe chart would correspond to the pH. A look at the graph accompanying this paper will show that except for very minor variations the graphs of the chart reading and the pH reading are parallel. The upper graph shows that the pH reading and the lime titrations also correspond and that the cyanide titrations appear to have little effect on the pH reading.Table 1 gives the results obtained for the two months before and after the instal1ation of automatic control as well as the two months of control. Unfortunately there was a decided change in ore just after the automatic controls were removed. There was much less pyrrhotitc in the ore than usual thus changing the need for lime and cyanide."

Jan 1, 1964

By Eldridge Haynes

IF you ask the average American to define 'total war' he is apt to fumble for an answer. But in Britain everyone knows the answer, because Britain has mobilized its total labour force, including women. If we were to match, proportionately to our population, Britain's mobilization of labour, we should have 60,000,000 people working full time in the armed services, civilian defence, and war industries. Actually we have fewer than 35,000,000 so employed. In Britain two out of every three persons between the ages of fourteen and sixty-five are so engaged. For the first time in the history of any democracy Britain conscripts women for service in the army, navy, and air force. Two hundred thousand British women have been conscripted for the army, known as ATS, meaning Auxiliary Territorial Service. There are more women in the air force than the total personnel of the RAF at the outbreak of the war and almost all of the land base jobs of the British navy are now handled by women. In addition to cooking and office work, Britain's women soldiers and sailors are driving trucks and motorcycles, repairing motor vehicles, packing and repacking parachutes, installing, inspecting, and maintaining gun equipment and ammunition of combat planes after each raid, raising and lowering barrage balloons, forecasting weather, manning harbour craft, sending and receiving radio messages. A normal ack-ack unit is composed of 229 women and 189 men. The women man the gun height finders and predictors, give bearings, and signal to fire.

Jan 1, 1942