Search Documents

By V. Bonilla-Sierra, M. Elmouttie, L. Scholtès, F. V. Donzé

In the presence of joint sets sub-parallel to a slope face, the stability of the rock mass is controlled by the shear strength of the joints. On one hand, if the joints are persistent their shear strength can be assessed according to Mohr-Coulomb criterion, assuming appropriate values for the cohesion and the friction angle on the joint surface. On the other hand, if the joints are non-persistent with their continuity being interrupted by the presence of rock bridges, their shear strength will increase considerably. In this latter case, the contribution of the rock bridges to the shear strength of the joint has to be accounted for in order to better assess the stability of the rock mass. A numerical analysis of the progressive failure of a rock slope involving a non-persistent joint has been set up based upon simulations performed using a Discrete Element Method (DEM) algorithm specifically enhanced for the modeling of jointed rock masses. Pre-existing discontinuities are explicitly accounted for in the model by using a modified contact logic that ensures an explicit and constitutive mechanical behavior of the joint planes. In addition, rock bridges can be spatially distributed along these joint planes following a prescribed probabilistic technique. Jennings’ formulation (Jennings, 1970) is considered as one of the first rock slope analysis that evaluates the shear resistance to sliding as a weighted combination of the shear resistance of the intact rock and the joint planes. The validity of this formulation is discussed in the present study. Contrary to the Jennings’ formulation, we show that tensile failure is an important mechanism, particularly as the dip angle of the sliding plane increases.

Jan 1, 2015

By G. V. Poropat

Roughness of a discontinuity may be an important factor influencing shear strength of the discontinuity. Traditionally, determining the roughness of a discontinuity surface and providing a numerical measure of the roughness has required considerable effort or specialised equipment. The development of new 3D imaging tools that are easy to use has provided effective fast and accurate means of creating 3D surface models from which roughness measurements can be readily obtained. These new techniques are versatile enabling a user to measure roughness along any desired profile and at any resolution up to the limit of the spatial subtense of a measurement on the discontinuity surface. This paper primarily reviews extensions to the use of 3D imaging that enable the measurement of roughness. Additionally we provide some examples of the measurements and examine some of the issues associated with extracting measures from the spatial data that will support estimation of shear strength.

May 1, 2009

The use of roof bolting gave promise of substantial economic benefits to Continuous Miner operations at Michel Colliery. As the first step in the adoption of bolting, 142 anchorage tests, employing six types of anchor shells, were made in three mines. Significant differences were found in the anchorage capabilities of the various shells and the various roof rocks. Introduction S PORADIC attempts at roof bolting had been made at Michel Colliery over a period of ten years. Results were indifferent or inconclusive. A concerted effort was not made, because a compelling need for bolting did not exist. By 1962, however, the advent of Continuous Miners had brought a new significance to roof bolting and, at the same time, the increasing price and scarcity of mine timber made bolting materials more competitive in cost. A fresh appraisal of bolting, therefore, became justified and necessary. The potential benefits of roof bolting at Michel are several.

Jan 1, 1963

By H. W. Little

INTRODUCTION MINERAL deposits of Salmo map-area (Figure 1) have aroused the interest of prospectors for more than a half-century. Properties within the map-area have produced lead, zinc, silver, tungsten, and gold. Sheep Creek mining camp ranks fifth in the Province in the total production of gold, but during recent years interest has been concentrated upon base metals, and meticulous prospecting and exploration have resulted in the discovery of many large zinc-lead orebodies. PREVIOUS WORK Geological investigations of the region were begun long ago, and it is interesting to trace the development of ideas with our increasing knowledge of the geology of this complex area. The first geological examination of the rocks of Salmo map-area was made in 1859-60 by H. Bauerman (1), who was employed as geologist accompanying the first international Boundary Survey. Bauerman examined the rocks exposed along Pend d'Oreille river and published a section indicating that the sedimentary rocks are probably of Palaeozoic age, and are intruded by granite of unknown age. McConnell and Brock(2), in 1894 - 1900, carried out the reconnaissance mapping of the West Kootenay Sheet, on which they outlined the Mesozoic rocks of the Rossland Beaver Mountain volcanic groups that they believed rested unconformably upon the sedimentary rocks to the southeast, which they regarded as of Palaeozoic age.

Jan 1, 1951

By G. W. Brooks

This short article is quite different to the general run of papers that are presented to the Institute, but no apology is offered because I consider that first-aid and mine-rescue work are of equal importance to many other subjects that are dealt with in our Transactions. Members of the Institute should be as much interested in the safety of persons engaged in the mining industry as they are in the practical methods of modern mining. We must not only do our best to conserve life and property by adopting every known device to that end, but we must also prepare ourselves so that we may take prompt and effective action when life is in danger, or when property is subject to loss. The need for such preparation in Alberta is perhaps greater than in most places where mining is carried on, and we must spare no effort to assemble at every mine men who are well trained in first-aid and mine-rescue work. The large area over which the mines are distributed renders central training stations out of the question, hence the need for local rescue-teams. Hospitals with skilled staffs, close enough to the mines to be convenient, also seem to be out of the question; therefore the greater need of a high standard of first-aid training for the people in our mining camps. The Government mine-rescue cars are supplied with the equipment necessary for training persons in this essential work and also for dealing with disasters should they occur. The question then arises: are there a sufficient number of men who are trained ? If so we can rest assured that what is possible to be done will be done. But if a sufficient number of trained men are not available much loss of life and damage to property is likely to result.

Jan 1, 1925

By G. Danha, S. Wabula, D. Glasser, D. Hildebrandt, N. Hlabangana

"Impact tests on single particles or a bed of particles are used to determine the fracture characteristics of particles. Many different techniques have been adopted in comminution in order to find ways of optimizing energy consumption in the size reduction process. In this paper, we apply one such method called the Attainable Region (AR) analysis technique to optimize the impact energy on a bed of silica particles. The attainable region is a fundamental approach that is equipment-independent and can be used to analyze breakage processes. The AR is defined as a set of all possible outcomes, for the system under consideration that can be achieved using fundamental processes operating within the system.INTRODUCTIONThe energy crisis in Southern African has reached such critical levels, that most cities in countries like Zambia, Zimbabwe, Lesotho, Swaziland and even South Africa are experiencing load shedding challenges lasting sometimes up to 18 hrs a day. Southern Africa is well known for its riches in mineral resources, and the economies of most states in this region are driven by the mining & mineral processing sector. With the emergence of small scale miners due to government empowerment policies, national energy providers have had to resort to power cuts mainly to domestic users in a bid to cope up with the huge industrial electricity demands.It has been estimated that about 4% of the total energy used in the world is consumed by the mineral processing sector (Fuerstenau & Lutch, 1999). Tomanec and Milovanovic (1994) estimated that milling alone accounts for more than 50% of the total power used in mineral processing, but this can rise to as high as 70% for hard or finely dispersed and inter-grown ores. Today, the greatest challenge in mineral processing is how to optimize energy input to the size reduction process (Dey & Das, 2013; Nomura & Tanaka, 2011), where it has been observed that only a small percentage (1.5%) of the total energy input really does the breaking (Khumalo et al., 2008) while the rest is consumed by the equipment concerned and lost to contacts that do not result in breakage. The immediate benefits of focusing research on the optimization of energy in size reduction operations in the mineral processing sector lies in potential savings on industrial electricity usage that may then be directed towards domestic users."

Jan 1, 2016

By Rashid Bashir

Shaft sinking through solid rock, which contains little or no water, poses little difficulty. However, when loose, water-bearing strata have to be contended with, water control measures, and pumping facilities are needed. Shaft sinking in Athabasca Basin requires sinking through water bearing sandstone which can be highly fractured. Intersection of local zones of extensive fracturing results in the potential for high water inflows with pressures up to 5 Mpa. Grouting is carried out ahead of each shaft sinking interval as water control strategy. In the grouting method, liquid cement is forced into the water-bearing earth under very high pressure. Shaft sinking performance which can be quantified in terms of rate of advance is highly dependent on the days spent at each interval grouting before sinking can advance to the next interval. This paper presents the shaft sinking experience in Athabasca basin and how some of this is translated into Geoscientific Investigations for Future Shafts. A comparison of Geoscientific data collected from future shafts at McArthur River and Millennium Mines is compared to historical data collected from pilot holes, where shafts have already been sunk. The paper concludes with the strategies for better integration of hydrogeological, geotechnical and geophysical data.

Aug 1, 2010

By G. Gauvin

Life span of aluminum smelting electrolysis cells can reach up to 3000 days. During this period, cathode blocks go under various physical and chemical changes that could result in an increase of electrical resistivity. The increase may be due to carbon migration from the cast iron to the steel bars, gap evolution between the cathode block and the cast iron, cathode cracking, etc. This paper focuses however only on the collector steel bar electrical resistivity evolution. To reveal the main phenomena responsible for the electrical resistivity increase, chemical analysis, metallographic and electrical resistivity tests were conducted on two steels bars picked from two Hall-Héroult cells after autopsies. Cathode voltage drop and temperature were measured using electrically insulated internal probes and thermocouples on 16 samples from each steel bar. Electrical resistivity can reach up to 1.21µO-m for a steel bar aged 2505 days compare to 0.142µO-m for steel AISI 1008 at room temperature.

Jan 1, 2011

By Naizhong Xu

During the past 30 years, fully mechanized caving mining has played a positive role in the improvement of the efficiency of coal production, but which has also had a great influence on the mining environment, especially to environment damage of shallow mining areas in the central and western regions of China. The surface subsidence parameters are the basis of the surface environment evaluation and governance. During 1980~1990s of the last century in China, fully mechanized mining subsidence laws were researched more fully, however, since coal caving technology is affected by many factors, and researches on its mining subsidence laws (parameters) were found to be grossly inadequate. Through actually observed in recent years, it is considered that coal caving mining subsidence laws (parameters) can use fully mechanized mining law (parameters) for reference. Based on fully mechanized mining laws (parameters), this paper reveals the similarities and differences of the surface subsidence laws between fully mechanized caving mining and fully mechanized coal mining, which can guide the work of coal mining under buildings, water bodies and railways in new mine area and mine collapse governance.

Aug 1, 2013

By R. M. T. Raja Ismail

Shipping and stevedoring industry is going to witness a massive increase in the amount of containers to be handled while land constraints become more critical. Offshore transfer operations hence offer a preferable solution to deal with the surge in cargos rather than to expand the port outwards. Recently, there has been increasing research interests on offshore crane automation. Suspended cargos in a ship-mounted crane system are caused to swing due to the vibratory motion of the ship induced by ocean waves, which can lead to collision between cargos and deck. Therefore, it is vital for offshore crane systems to satisfy rigorous requirements in terms of safety and efficiency. This paper presents the modelling and control development for offshore boom crane systems. A second-order sliding mode control law is proposed for trajectory tracking and sway suppression control, making use of its capability of actuator chattering alleviation while achieving high tracking performance and preserving strong robustness. The asymptotic stability of the closed-loop system is guaranteed in the Lyapunov sense. Simulation results indicate that the proposed controller can significantly reduce the effect of disturbances coming from gusty waves and other dynamic loadings.

Aug 1, 2013

By Mustafa Kumral

Monte ? Carlo simulation is often used to assess the risks associated with uncertain variables in mining operations. The success of Monte-Carlo simulations depends upon reproducing the dependencies among variables to some extent. However, some variables may exhibit different dependency patterns. In these cases, classical techniques for dependency quantification cannot capture dependencies. As an alternative, the copulas allow modeling nonlinear dependencies. Furthermore, any choice of marginal distributions can be used. Especially, for the data, which is sensitive to extreme case such as financial crisis, the copulas arise as a means to reproduce the correlations among variables. In this paper, the copulas are introduced to mining practitioners using Monte-Carlo simulations for risk assessment. Then, a case study is given to show the superiority of the copulas over classical techniques using ModelRisk Software. In conclusion, it was observed that the copulas enhance the quality of Monte-Carlo simulations by capturing variable dependencies.

Aug 1, 2013

By K. Ihara, T. Yamaguchi, K. Matsumoto

"Al-Fe alloy sheets having layers with different strain components were produced by unlubricated hot rolling and the recrystallization texture formation during annealing was investigated in each layer. In this study, the strain component introduced by rolling was quantitatively evaluated by measuring degree of bending of an aluminum pin embedded in the sheet. The textures before and after annealing were investigated by the SEM-EBSD technique. It was clarified that, in the middle layer, where comparatively small shear strain was introduced, ß-fiber subgrains and cube {001}<100> oriented subgrains were formed before annealing, and cube oriented recrystallized grains grew after annealing. On the other hand, in the surface layer, where large additional shear strain was introduced, shear texture components and cube oriented subgrains were formed before annealing, and shear texture was retained even after annealing, while cube oriented subgrains did not grow and were encroached. It was suggested that introduced strain components influenced the recrystallization texture formation by inducing different distribution of the subgrain size, stored strain energy and orientation relationship with surroundings before annealing.INTRODUCTION The microstructure developed during the hot-rolling process of aluminum and aluminum alloys affect the mechanical properties of the final product sheets. Especially, the crystallographic orientation in the final product sheets affects the r- value and ears during deep drawing (Humphreys & Hatherly, 2004), then the texture control in the hot-rolling process is important. When the friction between the rolling roll and rolled sheet in the hot-rolling is large, both the rolling texture and recrystallization texture tend to be heterogeneous in the thickness direction. It is known in many rolled aluminum alloy sheets that the texture in the surface layer was different from that in the middle layer because of additional shear strain. It was reported that in the vicinity of the surface layer, where large additional shear strain was introduced, the shear texture <1 1 1>//ND and < 1 1 0> // RD which contain components of {1 1 1} <1 1 0> and {0 0 1} <1 1 0> developed during rolling, and the shear texture developed even after recrystallization annealing (Sakai et al., 2002). Particularly, it is thought that the <1 1 1> // ND texture contributes to improve the r-value and press formability (Inoue & Takasugi, 2007). Therefore, asymmetrical rolling and high friction rolling have been applied to improve formability of aluminum alloys by adding shear strain in the rolled sheets as deep as possible (Kamijo et al., 1972; Inoue et al., 2005). However, few researches have been focused on the microstructures and texture before annealing and thus, the detailed mechanism is still unclear how the texture after annealing is affected by the texture before annealing. In this study, the Al-Fe alloy of commercially pure aluminum was chosen as the first material to be studied in order to clarify the fundamental process of the recrystallization texture formation. The main purpose of this study is to clarify the effect of additional shear strain on the rolling and recrystallization textures in the hot-rolled sheets by analyzing the transition of microstructure and orientation distribution through recrystallization annealing."

Jan 1, 2018

By C. E. Cairnes

The Slocan mining camp in Kootenay district; British Columbia; has long been noted for the great number of its silver-bearing deposits; and for the success that has; in many instances; attended their development. The orebearing area lies east of Slocan lake and mainly within a radius of 6 to 8 miles of the mining town of Sandon. Within this limited area 135 or more properties have shipped ore in quantities of from 100 tons or less to more than 500; 000 tons; and with a total value in silver; lead; and zinc ranging from a few hundred dollars to well over $10; 000; 000. Of the three metals; silver has easily ranked first in value; with lead second and zinc third. Zinc production; however; made slow progress in the early years; and with . the exception of the Lucky Jim mine; and a few others where high-grade ore could be readily hand-sorted; was a detriment to the silver-lead ores until improved methods of separation enabled it to take an important place in the mineral production of the Slocan.

Jan 1, 1954

By E. Ghali, J. F. Dorion

This paper presents the results of on-going investigations on the influence of corrosion on the performance of support systems in selected underground gold mines. Rock support is exposed to various conditions that can be aggressive. Samples of corroded support were analysed using SEM and photomicrography to determine the main corrosion forms. Tests are on-going in controlled corrosion chambers to qualify and quantify the impact of rock and minerals particles on steel corrosion. As more data become available these relationships can lead to useful information on the choice of support systems and reliable estimates of their longevity.

Jan 1, 2011

By Juergen Antrekowitsch, Stefan Steinlechner

"Waelz oxide from steel mill dust recycling is usually sold to the primary zinc industry, where it is first charged to the roasters to eliminate the remaining fluorides and chlorides. This limits the overall amount of secondary materials which can be used because of different operating problems in the roasters. Another option, in the case where the halides are low, would be direct leaching with low or medium concentrated sulphuric acid. Unfortunately, because of the carryover of some steel mill dust, iron is also present in the Waelz oxide, reaching contents up to 5 wt.%. Since the objective is to treat the solution more or less directly by electrowinning, with only a few simple preliminary purification steps, iron in the solution is a very important factor. Various trials have been done to investigate the dissolution behavior of the iron contained in the Waelz oxide. Although the zinc extraction should reach a maximum, all other elements, especially iron, should be low. This paper describes the results of our research in this area and offers possible options for Waelz oxide utilization. There is also a focus on how other elements, present in the material, influence the dissolution behaviour of zinc and iron, and whether a loss of zinc is unavoidable, if low iron dissolution is required.INTRODUCTION One of the most important secondary zinc resources is the zinc oxide originating from steel mill dust recycling. For the treatment of high zinc containing steel mill dusts, the Waelz kiln process is the so called “best available technology” and it dominates the industry, with roughly a 90% market share. The product Waelz oxide contains mostly zinc oxide, but it also contains lead compounds and halides due to evaporation with the zinc. In addition, it contains iron and some slag compounds due to mechanical carry-over. The presence of halides limits the use of the material as an alternative concentrate for primary zinc electrowinning. Such halides can be reduced to a certain extent by washing and/or solvent extraction (see following chapter). Although lead is not troublesome and theoretically represents a second recoverable valuable metal, iron is unwanted and causes additional problems during leaching. Even though Waelz oxide is generally a highly welcome input material in primary zinc metallurgy, due to its high zinc content, it still contains halides, and in the majority of cases, the oxide must first be treated in a roasting process. Different circumstances, like accretion formation because of the lead and halogen compounds as well as unwanted cooling effects in the roaster, limit the amount of Waelz oxide which can be substituted for the primary concentrate. Another, even more limiting factor, is the allowable concentrations of chlorides and fluorides in zinc electrowinning, the last step in the primary zinc processing route (Ruetten, 2011)."

Jan 1, 2016

By M. Maeda, H. Sasaki

"Precious metals such as platinum, palladium, and rhodium are commonly used for automotive catalyst converters. To recover these metals with lower environmental load and cost, exposure to zinc vapor was proposed as a pretreatment prior to acid leaching. Alloying with zinc is expected to enhance dissolution of precious metals and reduce the amount of toxic chemical agents required for the leaching. This study examined the effect of the alloying pretreatment using model catalysts. Catalysts were immersed in leaching solutions for a predefined time with or without zinc vapor pretreatment, and the amount of dissolved metals was then evaluated. INTRODUCTIONAutomotive catalysts account for large portions of the world consumption of platinum (Pt), palladium (Pd), and rhodium (Rh) (Butler, J., 2011). Because of their limited production and high prices, recovery of the precious metals from spent catalysts is obviously an important issue. A representative structure of an automotive catalytic converter can be described as a monolithic ceramic support with a honeycomb structure which is coated with porous oxides such as those of aluminum (Al2O3), cerium (CeO2), and zirconium (ZrO2) (Heck & Farrauto, 2001; Matsumoto & Shinjoh, 2007). Small particles of precious metals, originally several nanometers or less, adhere to the oxides.Typical recovery processes for precious metals from scraps are shown in Figure 1 (a)-(c) (Habashi, 1997; Yoo, 1998; Shibata & Okuda, 2002). Precious metals can be recovered by using non-ferrous smelters as Figure 1 (a) shows. Smelted along with metals such as copper (Cu), precious metals and ceramics in the scraps are absorbed into the metal phase and slag phase, respectively. Because the metals separate from Cu as anode slime in successive electro-refining, such a process can recover precious metals as co-products of Cu. However, in order to prevent negative effects on the principal process, a specialized procedure is needed. Figure 1 (b) is a specialized approach in which scraps are melted at elevated temperature with Cu called the Rose process. Here Cu works as a collector metal, and the absorbed precious metals are then concentrated by oxidation of Cu. Such a process can separate precious metals from ceramics constituting catalyst converters. Smelting at high temperature, however, requires extensive equipment as well as a high amount of energy. On the other hand, hydrometallurgical processes may be effective to separate precious metals from ceramics into an aqueous solution, because chemical agents can act on these metals selectively (Figure 1 (c)). Leaching of precious metals, however, requires strong acid and oxidizing agents because of their corrosion resistance; this makes liquid waste disposal and the large environmental load controversial. To solve the problem, a metal vapor pretreatment was proposed (Okabe, Yamamoto, Kayanuma, & Maeda, 2003a, 2003b; Kayanuma, Okabe, Mitsuda, & Maeda., 2004; Kayanuma, Okabe, & Maeda, 2004; Itoh, Kayanuma, Miyake, Kimura, & Maeda, 2005). A flow diagram of the process using zinc (Zn) vapor is shown by Fig. 1(d). Exposed to Zn vapor, precious metals are expected to form alloys which dissolve more easily than pure precious metals, thus reducing the use of chemical agents and environmental load involved with successive leaching. In previous research (Sasaki, Miyaki, & Maeda, 2010; Sasaki & Maeda, 2010, 2012), dissolutions of precious metal alloys formed by Zn vapor treatment were examined in hydrochloric acid (HCl) using an electrochemical method, and it was confirmed that these metals dissolved at higher rates from the alloys than from their pure states (Figure 2). In this study, the availability of the alloying pretreatment was demonstrated by testing on model catalysts in leaching solutions."

Jan 1, 2012

By M. Lghoul

Acid mine drainage (AMD) remains one of the major environmental problems for the mining industry particularly for many abandoned mine sites. The production of AMD as is commonly known can significantly affect the surrounding groundwater and surface water of the mine site. With the objective to investigate the impact of the AMD produced at the abandoned Kettara mine site (Morocco), groundwater sampling campaign was performed at this site. The sampled waters were analyzed to determine the hydrogeochemical composition, and then results were analyzed using different studied methods such as multivariate statistical analysis and geochemical modeling techniques. Investigation results show that the hydrochemistry of sampled waters is characterized by the relatively significant enrichment of Ca2+, Mg2+ and SO4 2-. The typical mine waters belong to the (Ca2+ +Mg2+)-SO4 2-type. Seasonal variations in major ion concentrations were partly attributed to dissolution/ precipitation processes. The saturation index (SI) calculation of the representative dissolved minerals in waters show that groundwater samples are undersaturated with respect to most potential sulphated secondary minerals.

Aug 1, 2013

By J. Lebl, S. Bharti, D. J. Cornett

"This paper presents the design and application of blasthole mining to an area at Strathcona Mine previously employing post pillar cut-and-fill. Extensive mining in the area had led to gradually deteriorating ground conditions and post pillar stoping was no longer considered acceptable. Alternative methods had to be investigated.Conventional methods for mining in poor ground were rejected because of the high cost. Blasthole mining was selected because iI offered good productivity and safety with acceptable costs. The design of this approach involved field investigations and the use of numerical modelling to simulate the different blasthole options and their impact on ground stability. The blasthole design incorporated reinforcement with cablebolts, use of a radio-controlled remote LHD unit, large-diameter holes, blast design and wall control. Potentially unstable areas were outlined during mining with ground monitoring instruments and the results used to modify mining plans during the production phase.IntroductionIn underground metal mines there is a need to improve safety and productivity and lower mining costs in order to maintain reasonable rates of return on investment. This requires the application of good engineering design to both mine planning and ground control in order to optimize production and costs and to forecast potential problems during mining. The task becomes more important when extensive mining leads to gradually deteriorating ground conditions, making existing mining methods and techniques no longer acceptable from a safety point of view. Alternative mining methods must, however, be sufficiently productive to ensure profitability. This paper presents an example of the engineering design and operating approach used by Falconbridge in dealing with such a situation at Strathcona Mine."

Jan 1, 1983

By Youngsoo Song, Hyunjung Kim, Junhyun Choi, Siyoung Q. Choi, Gahee Kim

In this study, for the first time, to confirm the effect of bacterial growth phase on the malachite flotation were investigated in a well-controlled Hallimond tube system. The test results showed that the bacteria in the stationary phase exhibit two-fold greater floatability than those in mid-exponential phase. To understand the observed flotation behavior, complementary cell characterization tests and cell attachment tests were conducted. Interestingly, the bacteria at both phases exhibited similar surface properties as well as almost identical amount of cells attached onto the malachite, suggesting that the growth phasedependent flotation behavior cannot be attributed to the variation of cell surface properties and the extent of cell adsorption. On the other hand, cell detachment tests revealed that the amount of cells detached from the malachite surface is greater for the mid-exponential phase than the stationary phase due to the higher fluid drag applied to the cells at the mid-exponential phase, which was explained by the differences in the size and shape of attached bacteria onto the malachite surface. These morphological characteristics were found to cause the bacteria of mid-exponential phase to be separated highly sensitive and easy from malachite surface due to the fluid flow. Second, scale-up selective bioflotation tests were carried out in a 1 L Denver cell in malachite–silica binary mixture systems. Through the tests, we optimized the cell concentration and the malachite fraction in the feed. Overall, high malachite selectively was observed under optimized conditions (both recovery and grade showed more than 90%). The trend was in agreement with classical DLVO interaction energy profiles, which show the relative magnitudes of the adhesive forces between the mineral and the attached cell under equal hydrodynamic conditions.

Jan 1, 2016

By N. Plint, M. Potgieter

The Anglo Platinum Mogalakwena North concentrator was one of the first three hard rock mineral processing applications to utilise a HPGR circuit in preference to a SAG milling circuit. This was driven by the extreme competence of the ore that had given rise to throughput issues on the original South Plant. Despite more than adequate capacity and performance of the individual comminution units, the circuit has struggled to obtain full design capacity. A thorough review of the integrated performance of the circuit revealed a wide range of bottlenecks and underutilised parts of the circuit arising from design issues. Interestingly, the major opportunities lie in materials handling issues and mismatch of loads about the circuit. This paper presents the high-level outcomes and the associated opportunities, and is pertinent to all HPGR circuit designs.

Jan 1, 2012