Search Documents

By G. Morin, S. Amira, F. Chiesa, B. Duchesne

"The effect of heat treatment on the stress corrosion cracking (SCC) resistance of A206 aluminum alloy was studied using the breaking load test according to ASTM G139 standard. This method uses the residual strength measurement from tensile test specimens previously stressed axially while exposed to the 3.5% NaCl alternate immersion test according to ASTM G44 standard. The residual strength after exposure is used as a measure of SCC degradation. The performed heat treatments were conventional natural aging T4 and artificial over-aging T7 tempers in addition to artificial aging T6 temper added for purpose of comparison. These tests showed that A206-T4 has a good resistance to SCC at pre-loads up to 100 MPa while A206-T7 was prone to SCC for pre-loads of 0 and 50 MPa, and showed total loss of ductility for pre-load of 100 MPa. Both A206-T4 and A206-T7 pre-loaded at 150 MPa showed poor resistance to SCC. A206-T6 showed the worst susceptibility to SCC as it lost all mechanical resistance at the end of the alternate exposure to 3.5% NaCl solution, even without any applied pre-load. Metallographic analyses showed that the resistance of A206 alloy to SCC is mainly affected by the transition from pitting to intergranular corrosion attack. The initiation and the propagation of intergranular corrosion attack might be assisted by high stress concentrations in the pits, particularly for pre-loads higher than 100 MPa. The transition from pitting to intergranular corrosion can also be promoted by hydrogen evolution from growing pits, which supports crack propagation by hydrogen embrittlement.INTRODUCTIONA206 aluminum-copper casting alloy offers ones of the best mechanical properties among the aluminum foundry alloys. This alloy belongs to the 206 alloy family developed in 1970s as an alternative to the highly resistant and ductile but more expensive Ag containing 201 alloy (Tiryakioglu, 2009). A206 showed also good low cycle fatigue strength (Sigworth, 2002). These properties made A206 alloy a strong candidate for some vehicles lightweighting applications. In spite of its interesting properties cited above, A206 alloy was rarely used in critical applications due to its tendency for hot tearing and stress corrosion cracking (SCC). Studies of A206 hot tearing behavior showed that this tendency can be reduced by improving castability and by grain refinement (Sigworth, 2002). The optimisation of the casting design can also prevent the tendency toward hot tearing. The SCC of aluminum-copper alloys arises from their susceptibility to localised corrosion, especially in chloride containing media. The localised corrosion in Al-Cu alloys is caused mainly by their heterogeneous microstructure, where the presence of many phases leads to the formation of micro-galvanic coupling with the matrix. However, most of the studies aimed at investigate the SCC of Al-Cu alloys concerned the wrought ones, especially the AA2024 alloy tempered in the T3 (or derivative) condition and few studies concerned the 206 and cast alloys in general (Alexopoulos, 2009 and 2016; Campestrini, 2000; Vogt, 1998; Talamantes-Silva, 2008; Zhang, 2003). Jean et al. (Jean, 2009) studied the effect of heat treatment on SCC behavior of B206 alloy using alternate immersion technique and grain boundary attack method and did not find direct correlation between the two methods. Another study showed that aging of 206 alloy may make a casting susceptible to SCC (Sigworth, 2002). However, these studies did not provide detailed information about the mechanisms of SCC of 206 alloy, as well as the effect of the stress intensity. The present work investigates the effect heat treatments and the stress intensity on the morphology of the corrosion attack and the SCC behavior A206 aluminum alloy. This study uses the breaking load test according to ASTM G139. This test utilizes direct tensile specimens and was developed to give a more quantitative measure of the SCC performance of resistant aluminum"

Jan 1, 2016

By John E. Udd

"Mining research at CANMET is delivered by the Mining Research Laboratories Division (MRL), with facilities in Sydney, Nova Scotia; Bells Comers, Elliot Lake, and Sudbury, Ontario; and Val d'Or, Quebec. This paper gives an overview of the work of the Division as of early 1993. An addendum, at the end of this paper, describes the organizational changes that will take place in April 1994. IntroductionCANMET, the acronym for the Canada Centre for Mineral and Energy Technology, is the name by which the organization founded in 1907 as the federal Mines Branch is presently known. The name was changed in 1974, in order to give recognition to the importance of both minerals and energy technologies in the activities of the Branch. Further reorganizations have taken place since 1987. As a result of these, CANMET has assumed the status of a Sector (equivalent to the Geological Survey of Canada) and has been organized into four branches.The organization as a whole functions in an environment of semi-matrix management. Some of the ""line"" Divisions report to Directors-General for the appropriate branches while other, larger divisions, report directly to the Assistant Deputy Minister.The second dimension of the organizational matrix is composed of a number of ""staff' divisions which report to the DirectorGeneral for Policy and Planning. Each of these Divisions performs a function which is common to all of the ""line"" divisions. For example, the Research Projects Office is responsible for monitoring the range of research activities of CANMET and for recommending allocations of funds for both research contracts and operating budgets. The Library and Documentation Services Division is responsible for CANMET publications and information services. Likewise, the Engineering and Technical Services Division provides support through, among other services, the construction of specialized laboratory equipment."

Jan 1, 1994

By S. Sagar

In September 1996, Dofasco commissioned a 165 Mt twin shell EAF furnace and an associated ladle fleet. During and after this startup, refractory performance in the ladles was optimized on a holistic approach through several initiatives that increased ladle refractory retention times from 7000 to over 16000 mins (160 heats). This dropped the overall refractory costs by 40% while ensuring a consistent and predictable ladle performance. One initiative that drove enhancements was the proper brick selection for each particular refractory area and it's process conditions. The work concentrated on the selection of a resin bonded alumina magnesia carbon (AMC) brick in the barrel area of the ladle, upgrades to the 2 piece monolithic alumina cast ladle bottom and increasing the slagline refractory brick quality with the appropriate zoning/paneling. The adoption of a magnesia alumina carbon (MAC) brick in the transition area of the barrel/slagline has also improved performance and predictability. The design developments have lowered the overall wear rates and balanced the service life of the entire ladle. Safety was improved and breakout potential reduced by changing the safety lining from a high alumina brick to a state of art technology - monolithic shotcrete lining. This initiative decreased the overall manpower required to brick a ladle and increased shop ladle availability. The ladle bricking area environment was also improved by adopting a post combustion device to burn phenol fumes from ladle preheating practices. This has improved the overall health & safety of the reline teams. The consistent and predictable performance of the ladle on a whole has allowed the shop to decrease the number of working ladles in operation from 5 to 4. This further decreased wear rates from over-oxidation and excessive thermal cycling, saving approximately $500,000 in natural gas from pre-heater operations.

Jan 1, 2004

By H. Ikeman

"The highly specialized communication systems used in the mining industry place exacting demands on equipment and transmission media. Safely and reliability of services are perhaps the two most important factors. Fibre optics is ideally suited 10 meet these stringent requirements. Aside from being an intrinsically safe, non-sparking and EMI/RFI immune medium , fibre optics offers greater reliability , higher quality of services and superior flexibility over conventional copper or radio-based communication systems.This paper wilt show how fibre optics can be applied in mining industry applications. Emerging trends and concepts will be presented to show how fibre-optic-based integrated service communication networks and local distribution systems can be implemented.IntroductionCommunication requirements in today's mine s are varied and extensive. The communication system must be rugged , safe and reliable, yet provide an ever increasing amount of high quality services. Presently, these systems are implemented using conventional copper cable. As mining method s and technology advance and the demand for better and more communication services increases, traditional systems quickly reach their limitations. It is under these circumstances that we turn to fibre optic communication systems.Fibre optics is a mature technology which is finding its way into more and more applications worldwide. A fibre optic communication system can provide a level of performance unattainable by conventional cable systems yet ca n be cost competitive. As is well known, fibre optics provides a noise-free, noise-immune, high -capacity communications channel. Glass fibre, being dielectric and non-sparking, is an intrinsically safe communications medium. Clearly, it is ideally suited to the harsh environment present in a mine.From a communication systems point-of-view, the topology of a deep mine is unique. The objective of the systems engineer is to implement a total communications capability throughout this wide spread area. Ideally all classes of services should be accessible throughout the network-an integrated network concept. Recent advances in communications technology combined with fibre optics make this realizable."

Jan 1, 1984

By James E. Rider

"Fractures in mine hoist drumshafts are rare. We know of no previously reported attempts to repair a fractured drumshaft; any feasible method would involve welding and the associated problems of distortion, crack formation and strength.In June 1984, a fracture was discovered in the drumshaft of the production hoist in the Teck Corporation, Lamaque Division Mine at Val d'Or, Quebec. Delivery time on a new shaft would have been at least six months. The shaft was repaired in ten days and the total out -of-service time was four weeks.This paper describes why the shaft failed, how it was repaired, and the special alignment procedures employed during re-installation to minimize stresses in the repaired area.IntroductionThe performance of a mine hoist drumshaft is absolutely critical to mine operation. An inoperable drumshaft means no hoist, which in turn means no production or mine operation.Fractures in mine hoist drumshafts are rare. Previously when they have occurred, no one has seriously considered attempting a repair because of problems involved. Any feasible method would involve welding, which raises several major problems - namely, metallurgical, alignment, and strength.In July 1984 this very situation occurred at the Teck Corporation, Lamaque Division Mine in Val d'Or, Quebec.It was recognized that a new shaft would take at least 6 months' fabrication and delivery time. However, having had some experience at repairing broken shafts in other machines under similarly desperate circumstances, and after due consideration, it was concluded that by applying the correct techniques and engaging the right expertise, it would be possible to perform a repair and have the mine back in operation within a month.Thanks to outstanding efforts by all, the repair was accomplished in ten days and total out-of-service-time was only four weeks. The causes of the failure were determined and the calculated stress levels confirmed by strain gauge measurement during operation.The success of this project was achieved by adhering rigorously to fundamental management and engineering principles."

Jan 1, 1988

By James E. Rider

"Fractures in mine hoist drumshafts are rare. We know of no previously reported attempts to repair a fractured drumshaft; any feasible method would involve welding and the associated problems of distortion, crack formation and strength.In June 1984, a fracture was discovered in the drumshaft of the production hoist in the Teck Corporation, Lamaque Division Mine at Val d'Or, Quebec. Delivery time on a new shaft would have been at least six months. The shaft was repaired in ten days and the total out -of-service time was four weeks.This paper describes why the shaft failed, how it was repaired, and the special alignment procedures employed during re-installation to minimize stresses in the repaired area.IntroductionThe performance of a mine hoist drumshaft is absolutely critical to mine operation. An inoperable drumshaft means no hoist, which in turn means no production or mine operation.Fractures in mine hoist drumshafts are rare. Previously when they have occurred, no one has seriously considered attempting a repair because of problems involved. Any feasible method would involve welding, which raises several major problems - namely, metallurgical, alignment, and strength.In July 1984 this very situation occurred at the Teck Corporation, Lamaque Division Mine in Val d'Or, Quebec.It was recognized that a new shaft would take at least 6 months' fabrication and delivery time. However, having had some experience at repairing broken shafts in other machines under similarly desperate circumstances, and after due consideration, it was concluded that by applying the correct techniques and engaging the right expertise, it would be possible to perform a repair and have the mine back in operation within a month.Thanks to outstanding efforts by all, the repair was accomplished in ten days and total out-of-service-time was only four weeks. The causes of the failure were determined and the calculated stress levels confirmed by strain gauge measurement during operation.The success of this project was achieved by adhering rigorously to fundamental management and engineering principles."

Jan 1, 1988

"Adopted in 2003, theses guidelines are intended to assist the Qualified Person(s) in the planning, supervision, preparation and reporting of mineral resources and mineral reserve estimates. The report is divided into two broad sections “General Guidelines” appropriate for most metals and “Guidelines Specific to Particular Commodities” for potash, industrial minerals, uranium and coal. “These guidelines are reference in the Companion Policy of NI 43-101 with a statement that a qualified person classifying a mineral deposit as a mineral resource or mineral reserve should follow them.”Executive SummaryThe following is a summary, in table format, of the main elements of the Estimation Best Practice Committee's report ""Estimation of Mineral Resource and Mineral Reserve Best Practice Guidelines"". While the summary table is provided for convenience, the Committee recommends that the report be read in its entirety and the table summary not be used as a stand alone document. These guidelines are not intended to be either prescriptive or exhaustive. They do not preclude innovation. Preamble: These guidelines have been prepared by the Canadian Institute of Mining and Metallurgy and Petroleum (CIM) led Estimation Best Practices Committee. They are intended to assist the Qualified Person(s) (QP) in the planning, supervision, preparation and reporting of Mineral Resource and Mineral Reserve (MRMR) estimates. All MRMR estimation work from which public reporting will ensue must be designed and carried out under the direction of a QP in accordance with National Instrument 43-101 (NI 43-101) and related forms. A QP is defined in NI 43-101 as ""an individual who is an engineer or geoscientist with at least five (5) years of experience in mineral exploration, mine development, mine operation, project assessment or any combination of these; has experience relevant to the subject matter of the mineral project and technical report; and is a member in good standing of a professional association"". Disclosure of MRMR estimates is to be made in accordance with industry standard definitions approved by the CIM (the CIM Standards adopted by the CIM Council in August 2002) which have been incorporated by reference into NI 43-101."

Jan 1, 2003

By M. Leroux, C. J. Martin, S. R. Rao, J. A. Finch

"The effect of nitrogen on the flotation separation of sulphides from complex ores from Brunswick Mining and Smelting (New Brunswick) and Mattabi Mines (Ontario) was investigated. The most significant finding was enhanced pyrite floatability after as little as 3 minutes nitrogen conditioning. This was used in a novel sphalerite/pyrite separation process developed on the Brunswick ore. After aeration and Cu/Pb bulk flotation in air using xanthate the slurry was nitrogen conditioned, xanthate added and the pyrite floated in nitrogen. As an example up to 70% pyrite recovery with about 20% sphalerite recovery was achieved. Sphalerite was recovered from the pyrite tailings and the pyrite concentrate by copper-activation, raising the pH to 10 and floating in air. About 65-70% recovery at 35-40% Zn grade was achieved compared to 25% Zn grade by the conventional route. The process offers a promising alternative to current practice which seeks to depress pyrite at all stages. A possible mechanism of the effect of nitrogen is presented. INTRODUCTIONUse of gases other than air in froth flotation has been reported from time to time. [Podobnik and Shirley, 1982; Lin and Metzer, 1975]. Of all the gases, nitrogen would appear to hold the greatest practical promise because of its easy availability and chemical inertness. It is used in froth flotation in chalcopyrite-molybdenite separation [Redfearn, 1983]. The use of nitrogen in polysulphide chalcopyrite. this case is mainly to reduce the oxidation of a compound (Nokes reagent) used as a depressant for There is no reported use of nitrogen in the flotation of other sulphide minerals."

Jan 1, 1988

By S. Wood

"Plastic Filled Valley (PFV) wire rope represents a significant development over the design of conventional wire rope. A sealing thermoplastic is impregnated under controlled conditions of temperature and pressure into a conventional lubricated wire rope to produce a lattice of plastic which surrounds and separates the strands from each other and from the core. Metal-to-metal contact is thereby alleviated and the lubricant is sealed in. The wear resistance, rope breaking load, fatigue resistance and crushing resistance are all increased. The result is a rope which offers exceptional service life.Laboratory tests carried out in Canada and at the University of Stuttgart, in West Germany, confirm the increase in fatigue life. The field trials conducted so far have indicated that the results obtained in the laboratory can be duplicated in the field.IntroductionIn times of double -digit inflation, the consideration given to operating costs throughout industry commands considerable attention. The same can be said of the mining industry. A set of large-diameter wire ropes used on the huge draglines in strip mining can cost in excess of $100,000. Because a machine may use three sets of rope s each year, it is clear that the costs of wire rope can contribute a considerable percentage to any operating budget. As wire rope is a product which is used extensively throughout the mining industry, it would appear timely to turn our attention to any ""Method of Extending Wire Rope Service Life"" in order that wire rope life can be optimized and wire rope costs can be minimized."

Jan 1, 1982

By J. W. Jefferies

"Plant availability up 13%, production output up 40%, tons per employee up 15% and labor turnover down 52%. One mine manager states these were direct spin offs from the work being done to qualify for a safety award in the program known as the ""IMSRS 11 over a three-year period of time. ""Of Course"", stated this manager, ""these were in addition to an 87% reduction in our disabling injusry frequency rate.”Officially known as the International Mine Safety Rating System or the Five Star Mine Safety Rating, a new approach to mine safety is being used with enthusiasm by a significant number of mines in Canada, the U.S., Australia, Chile, Indonesia, the Philippines and South Africa. Significant results are coming into the International Loos Control Institute from over 125 mines from these countries.The program is built around a mine safety audit system that gives positive recognition to a mine at 5-step intervals along the way, (a star with each step attained). The Institute has licensed auditors in locations in Canada and the U.S. available to audit.It is believed the success of this program is the result of the premise upon which the program is based. The results being achieved are due to the concept that a modern, well-managed mine safety program maintains the basic foundation of a complete management system. When properly implemented, it reinforces those factors common to production, quality and safety. (Attitude - skill - knowledge - fitness - structure - machine - equipment - materials and processes). The IMSRS contains elements that reinforce all these factors. It uniquely treats safety as part of the ""right way"" to do the job and not just the ""safe way"" as a distinctly separate entity. Mines using this program now recognize that many of the older safety techniques were not necessarily the right way or the most efficient way to do things. It appears that this new approach to mine safety is a new avenue for the attainment of management's real goals for being in business, and at the same time achieves optimum support for the important target of safety and health for the mine worker."

Jan 1, 1983

By T. E. Newkirk

In the past few years there has been considerable controversy on the most suitable material to be used in ventilation doors which will have to serve also as fire doors. For this reason it was thought useful at Mclntyre to find out to what extent our zinc chloride treated spruce doors were fire resistant and what protection we could expect in case of an underground fire. The doors to be tested were constructed of the same material as that used in our regular ventilation doors underground, namely, 2-inch tongue-and-groove well seasoned spuce. It is to be noted, however, that whereas the dimensions of the ventilation doors are 5 ft. by 6 ft., those of the test doors were only 14 in. by 17½ in. The treated doors were made up from lumber that l1ad been treated with chromated zinc chloride, as described in Mr. Keeley's paper. Two kinds of tests were carried out: a heat test and a flame test. An electric muffle furnace for assaying, equipped with a pyrometer, was used for the beat test, the furnace door being replaced by the wooden door to be tested. In the flame test, the door to be tested formed one end of a rectangular steel box in which was placed a large blow-torch. Air was admitted at the rear of the box. A pyrometer recorded the temperature at the inside surface of the door where flame impinged. The results of the tests are presented in the accompanying table, in which the word 'failed' is to be interpreted as meaning that the door had been damaged to the extent that smoke, but not necessarily flame, issued from its outside surface.

Jan 1, 1949

By E. H. Holm

"This paper is a market-oriented review of the industry's present and forecasted performance, considering some of the principal factors influencing natural resource development. The author illustrates the steady consumption growth of nickel, and stresses the need for a quantitative long-range approach to production, consumption and the supply/ demand balance on a worldwide basis. Objective consideration of this data exposes some popular misconceptions. The possibility of near-term undersupply of nickel is discussed in relation to historically rapid changes in inventories and demand patterns. What is the significance of the increasing reliance on lateritic sources? New• facilities, new processing methods and new product forms are illustrated as further evidence of the industry's determination to satisfy the needs and preferences of nickel consumers. Examples indicate how product forms must accommodate to fast-evolving end-use technology. A review of nickel's price performance is used as a base from which to explore tomorrow's price trends."

Jan 1, 1972

By H. R. Manouchehri, A. Weh

"High voltage electric pulse comminution (SELFRAG) relies on inducing electrical breakdown that occurs when the resistivity of a dielectric is insufficient to completely block all transfer of electricity while the conductivity is not high enough to fully accommodate the flow of electricity without considerable changes to the crystal lattice. The technology is based on introducing the electrical discharges into solids immersed in water and placed between two electrodes. The technology has received significant attention since investigations have revealed the potential for fully fragmenting particles or pre-weakening rocks in order to reduce the energy consumption in comminution practices, improve liberation and potentially increase the recovery in mineral processing. Mineralogical analysis of samples showed possible liberation at coarser sizes by high voltage breakage in comparison with conventional mechanical comminution.This study explored the potential of implementing SELFRAG to treat the Sandvik’s Mittersill mine tungsten ore (scheelite) for recovery improvement. Accordingly, standard SELFRAG tests were conducted on four samples from the tungsten process plant to evaluate the energy-breakage relation and potential to liberate the value minerals at coarser size fraction for recovery improvement. The size reduction of the ore after processing with SELFRAG revealed that size deportment occurs at 0.4, 0.2, and 0.1 mm, which indicated potential liberation of gangue and target minerals at respective sizes. In comparison with conventional milling, the difference is the deportment of values into 0.4 mm sizes, which was, to some extent, confirmed by SEM liberation analysis. However, more tests are needed to proof the concept. The study has indicated that, despite consuming more energy in comparison with conventional mechanical comminution, there are promising prospects in liberating the values at coarser fraction and improve recovery by making use of SELFRAG. The energy consumption can be reduced through customized generator and equipment setup, which must be further investigated."

Jan 1, 2016

By Keith C. Hendrick

"Metal prices are frequently the most critical and least predictable element in determining the profitability of mining operations. Short -term fluctuations can be offset in varying degrees by hedging or other market actions. Such solutions are not practical for the longer term, The paper investigates the nature and extent of metal price risks and evaluates methods to reduce them.IntroductionIt is management's responsibility to improve the odds by managing the-risks by identifying them clearly, assessing them accurately, minimizing them where possible-and, then, timing decision s success fully.In determining the profitability of current operations, preparing forward plan s or developing feasibility studies for new projects or expansions, pr ices are usually the most critical input. Being market determined rather than cost based, they can also be the most unpredictable As a result, commodity prices are frequently the greatest of all risk factors.Nature of Commodity PricesThe cyclical nature of commodity prices is well known. They are stable only when supply is in balance with demand and forecast to remain that way. An imbalance on either side of the equation can lead to a price reaction completely out of proportion to the actual or perceived surplus or shortage.This exaggeration arises through the cumulative effect of market forces. When the market senses an uptrend, consumers buy for the expected increase in activity. They also seek additional quantities for inventory before price s rise. Merchants defer spot sales anticipating higher price s, speculators go along for the same reason, and producers raise prices in response to demand. Events tend to confirm the expectation of each party and strengthen their reaction causing prices to move higher."

Jan 1, 1983

By E. W. Coderre, R. C. Baxter

"This paper describes the townsite of Wabush and the two railways operated by Wabush Mines for the loading and unloading of iron ore concentrate. The town of Wabush is located approximately 200 air miles north of Sept-Iles, Quebec and is in the Province of Newfoundland and Labrador. Construction of the town-site began in 1961 to provide housing accommodation for the construction force and permanent employees in the mining and milling operations located 4 miles away. Wabush Mines operates two short railway lines in loading and unloading concentrate between the concentrator, located at Wabush, and the pellet plant at Pointe Noire, Quebec. Both of these railways connect with the main line of the Quebec North Shore and Labrador Railway and provide a shuttle service between the two phases of the operation."

Jan 1, 1969

By S. Zakaria

"Inco's Automated Haulage Truck System (AHT) is a revolutionary automatic guided vehicle that performs all load, haul and dump operations without human intervention. The high level of sophistication and the short period it has been in operation has only allowed a select few Inco personnel to become familiar with the ART operation and maintenance. As an aid to operations an expert system using the knowledge gained from the experienced specialists was implemented in the field.The AHT operating and maintenance assistance expert system will reason through the information given, arrive at conclusions and give advice to operations, technical and management personnel. It will provide comprehensive real-time troubleshooting assistance for the hydraulic, electrical and mechanical subsystems of the ART. The ART expert system has many benefits to Inco which include increased skill levels of ART operations and maintenance personnel, reduction in ART downtime, standardization of troubleshooting procedures and reduction in ART operating and maintenance costs. In the future, the expert system application will be linked to SCADA (Supervisory Control and Data Acquisition), maintenance and statistical software to display current and historical trends of variables from a centralized historical database. As well, a wide variety of features will be integrated into the system including AutoCad drawings, graphics, photographs, voice and video capabilities."

Jan 1, 1994

By John A. Dresser

Seventy years ago a period of prospecting and mining activity began in the Eastern Townships of Quebec that seems to have been quite equal to that of recent years in the Rouyn field. In the following six or seven years a large amount of work was done over a widespread area. About fifty deposits gave some shipment of ore, from a few tons upwards, and as many as five hundred occurrences of copper were made known in the district by official records. Comparing the scale of commercial undertakings of that time and of the present day, these developments must have occupied quite as large a share of the capital and man-power of the Province as northern Quebec employs today. Working conditions at that time were not very favourable. The country was then only newly opened for settlement, and colonists were few and widely separated. Roads of the class built today were unknown. A single line of railway, the Grand Trunk, crossed the district from east to west. Colonization companies controlled large blocks of land on which they owned mining rights and usually reserved these rights in whole, or in part, when selling the lands. Then, as now, the precious metals belonged to the Crown. Yet the work was not without its successes. One of the first deposits discovered, the Acton, was, for a few years, one of the most profitable producing copper mines of its time. Another, the Eustis mine, has been in almost constant operation ever since, and is now vigorously pushing further development. At least two others, now quiescent, proved profitable operations, and several made considerable production. The manufacture of sulphuric acid in Canada was begun by the founder of the Nichols Company at Capelton, on a deposit that is now being re-developed, after a long and creditable career.

Jan 1, 1928

By W. Holyk

"Although lead, zinc, copper, and iron sulphides have been known for many years in the Bathurst region, the existence of large massive deposits was not known until the discovery of the Brunswick orebody in 1952. This was followed by the discoveries of the Anacon orebody in 1953 and the American Metals orebodies in 1954. There is no question as to the great importance of these large massive sulphide deposits, and no doubt that other sulphide deposits are to be found. The problem, of course, is where and how to find them.The discovery of the Brunswick and Anacon orebodies is attributed to geophysical work. The original discovery of the American Metals deposit is generally attributed to a regional airborne electromagnetic survey.It is generally stated that the Bathurst area is a geophysical camp, and this is essentially true, but in this highly competitive search for orebodies it is obviously impossible for an individual company to cover the entire area by a comprehensive geophysical survey. Some means other than geophysics must be used to narrow the target. The quickest, cheapest, and simplest method is geological investigations.It has been stated that nothing can be accomplished by geology in the Bathurst region, since the camp is largely covered with overburden. This is true only insofar as detailed work on certain properties is concerned. It is not true of the larger regional picture. Outcrops are scarce, but angular float is abundant, and precedent shows that angular float has moved but a short distance from its source.GeologyAeromagnetic maps published by the Department of Mines and Technical Surveys are the best guides to the geology and structure of the area. These maps supply factual information concerning the underlying rocks. When coupled with field investigations, they are very useful in the interpretation of regional geology and the selection of favourable areas. The discussion of the geology is accordingly centred upon the aeromagnetic maps. The following is essentially a working theory, based on geological facts as best reconciled with all other available information,"

Jan 1, 1949

By K. G. Markkola

The Minera Candelaria concentrator was commissioned in August 1994, and in October 1997 it doubled its grinding capacity. The concentrator was designed to treat 56,000 metric tonnes of copper ore with a primary crusher, two grinding circuits, pebble crushing, and flotation. The grinding circuit includes two 11.2 m (36 ft) diameter by 4.6 m (15 ft) long semi-autogenous (SAG) mills, each fitted with a 12 MW motor. Throughout the history of Candelaria, different strategies have been developed to maximize the plant's operational time, strategies that include increasing the life of the SAG mill liners and reducing the time involved in changing these elements. This work describes the improvements made in the design of the liners, the change planning, and a new strategy to change the liners with the purpose of increasing their use and throughput.

Jan 1, 2007

By J. H. Nantel, J. F. Archibald

"The presence of radon from uranium-bearing ores, waste and from backfill material introduced underground to provide ground support, work platform and waste disposal functions, requires that ventilation controls be established to maintain safe working level concentrations. One approach has been developed at Queen's University to quantify radon and radon daughter source level s and to estimate ventilation requirements necessary to maintain these safe levels.Knowledge concerning the sources of radioactive contaminants and their production quantities is of value for planning and design stages of ventilation control systems. For any given mine layout, radiation level estimates may be forecast and modified by ventilation network design where excessive production quantities may exist.Behaviour of Radon Gas in MinesRadon gas, produced from the decay of Ra-226 in a host medium, will diffuse through porous media. In areas adjacent to mine workings, radon will be liberated into the mine atmosphere. The rate of radon emanation is proportional to the rate at which radon is produced within the host material (a function of the ore grade of U308) , to the radon concentration gradient in the host pores and to the diffusion properties of the material.The radon source concentration is determined by the rate at which Rn-222 is produced by the decay of Ra-226, and by the emanating coefficient (E), or fraction of the radon which escapes from the source matrix and is free to diffuse through the pore spaces."

Jan 1, 1984