Search Documents

By M. Sider, D. L. Piron

"The cost of energy is a growing factor in the cost of zinc production. Electrowinning from sulphate solutions with periodical reverse current or from acidic chloride or alkaline solutions could be the way to lower costs. A comparison of the energy consumption for electrolysis shows that the alkaline solution may be considered the most promising alternative. IntroductionZinc electrowinning from sulphate solutions is a very energy intensive process (typical specific energy usage : around 3.1 kWh / kg zinc). This energy consumption represents 35% of the total cost of electrolysis and is the most important cost component.In order to lower costs, the energy efficiency of the sulphate process should be improved or alternative processes should be developed. In this laboratory, that objective has resulted in research on electro winning in sulphate solutions with the use of periodical reverse current (PRC) and in acidic chloride and alkaline solutions.Some of the results obtained in this laboratory and already published and new experimental results reported in this paper make it possible to present a more critical comparison of the energy consumption of the three processes mentioned.ExperimentalThe experiments at constant current were carried out as described previously. Specific conditions are indicated in Table I. Current efficiencies were obtained by weighing deposits.ResultsThe best energy consumptions for electrolysis obtained in this laboratory for the three media are presented in Table I. More detailed results can be found in the papers already mentioned."

Jan 1, 1988

By E. Burdukova

Long-chain primary amines are utilized as collectors in potash ore flotation. Krafft temperature of long-chain amines in brine is about 100 °C, and this makes such amines practically insoluble in brine at room temperature. When dodecylamine, melted at 70 °C and dispersed in hydrochloric acid (or acetic acid) aqueous solution, is added to a KCl-NaCl saturated brine at room temperature, the amine precipitates. The experimental results demonstrate that the precipitating amine hydrochloride particles are selectively abstracted by KCl particles, but not by NaCl particles.

Jan 1, 2009

By Roger V. Pierce

"WITHOUT mineral wealth, modern man would not exist. True, man could survive on a stone-age basis with an average life expectancy of, say, 25 to 30 years -once he got past infancy.However, no metal would tip his arrow in a hunt for protein; no steel plough would break the soil for the organized planting of seed; and no coal, nor oil, nor natural gas nor uranium fuels would pro-vide him with light or beat or safety from either beasts, or other men, or an unkind nature that threatened him and his family.Modern agriculture, fishing and forestry represent the other three wealth-producing industries. With-out metals, non-metallics and energy minerals, however, it would be impossible to fit any of these to man's modern needs."

Jan 1, 1967

By Zia Pirzada

"Time is of the essence" and "Time is money" These are powerful and true statements during a project life cycle and have far-reaching implications on the success and failure of the project Time and progress management is crucial to the project success. Project delays may increase the cost to an unacceptable level and may render the project as economically unfeasible. On the other hand, if the project is completed on time or earlier than as planned, it may generate economic benefits greater than what had been envisioned To take advantage of the financial opportunities and to improve the cash flow as well as Return On Investment (POI), project schedule can be accelerated to complete the project earlier than planned Project schedule acceleration can be achieved by using analytical tools, such as "Schedule Optimization", "Schedule Reduction", "Schedule Compression" or a combination of any of these concepts along with the "Planning for start up". Schedule optimization does not entail any extra cost, however, other acceleration methods, such as Schedule Reduction and Schedule Compression, may require extra expenditures from the owner. Based on the forecasted early start of the revenue stream, the extra expenditure could become a worthwhile venture with a very high rate of return To accelerate the schedule, all aspects of the project should be reviewed with acceleration costs calculated. All risks and opportunities should be evaluated and taken into consideration to determine if the acceleration is feasible and advisable and will provide definite financial advantages Sometimes schedule acceleration may be desired to prevent the company from paying liquidated damages. This is especially true when the project is not expected to complete on the contractual completion date and when the cost of acceleration is less than the liquidated damages that may accrue against the company.

Oct 1, 2010

Abstract: ?The paper will review the perspective of Scotia Capital on financing mines, mining projects and mining companies in today's world of major increases in commodity prices, increases in capital and operating costs, shifts in foreign exchange rates, and increasing scrutiny of mining's social license ?Focus on debt financing alternatives Key Assumptions: ?Assume financing a mining asset (i.e. not an exploration play) ?Exploration is generally financed with equity ?private placements or public offerings on an idea

May 1, 2006

By G. Reuben Yourt

This paper consists of two main parts. The first, under the heading Preparations, deals with suggested preparations to be carried out in advance so that loss of life might be prevented should a fire occur. The second part, under the heading Fire Procedure, deals with actual organized procedure to be followed for the preservation of life if and when a fire occurs. The writer realizes that these preparations and procedures may be to some extent applicable to only a few mines with a relatively simple vein system and that each mine would need to formulate a procedure to conform to its own particular conditions, scope, and degree of complexity. Preparations 1. - Ventilation Control The objective in ventilation control in the event of a tire underground is to keep the travelways, through which men must pass to reach surface, supplied with air not deficient in oxygen and free from gases and smoke. Without some control of the volume and direction of the main air currents flowing through the mine, the success of removing men to surface might be seriously hampered. ? This control is achieved by means of mechanical ventilation forcing air through desired airways and workings with the assistance of doors to regulate the volume and direction of the air flow. In connection with fans and doors, the possibility of short-circuiting should always be taken into consideration, as it can often nullify the value of a fan and possibly trap men in dangerous atmosphere if the short-circuiting involves the fire area. Main fans are often installed so that they can be reversed in a short time. However, fans should not be reversed unless this is found absolutely essential by those in authority. Misjudgment in this respect could cause the loss of life to men who might naturally take refuge in what they believe by experience to be a fresh air stream. Another precaution to be taken is to see that doors in airways are fastened in a fixed position so that they cannot be sucked or blown open when the fan is reversed, otherwise short-circuiting could possibly render the fan useless.

Jan 1, 1947

By Rob Kelso

The PISCES Goals ? To conduct research and develop programs to enable and promote planetary surface exploration ? To host international tests and technology demonstrations at the PISCES Test Site. ? To promote STEM education, inspiring students by connecting Hawaiian culture to space exploration and settlement. - economic and workforce development ? To involve the commercial sector, spinning off technologies to help the local Hawaiian economy. ? To develop a full-scale, technically valid, analog lunar/Martian outpost on Hawai`i Island.

May 1, 2013

By P. Radziszewski

Industrial practice in mineral processing shows that an important problem in understanding and monitoring in-mill parameters is due to the lack of fundamental knowledge and appropriate sensors. With the development and growing use of DEM charge motion simulators for mill optimisation and design, it is possible to describe the fundamentals of grinding mill behaviour, in improving the understanding of internal grinding mill dynamics and in developing solutions to industrial practice. The main challenge to bringing this DEM technology to the mill operator however was the need for substantial computing power and time. However, what about a simplified DEM charge motion model running in real-time? What about the use of sensor technologies to correct any possible drift in simulator prediction? Could such a technological system be used to predict mill performance and eventually be used for mill control and optimisation? Some of these questions are answered with the development of an "on-line" DEM charge motion simulator package (SAGTools?) along with that of a number of sensor technologies (liner wear, acoustic, instrumented ball) that can contribute to simulator precision. With the objective of bringing this modelling and sensor technology into the concentrator control room to assist operators, this paper aims to describe the main elements of this emerging and developing technology and discuss how it can lead to online mill performance prediction and eventual control.

Jan 1, 2007

By Chester J. Kuryliw

"The Geology of the Cochenour Willans mine, Red Lake district, was described by J. P. Nowlan in the Jubilee Volume. The complexity and intense alteration of the rocks obscured any clear relationship between ore and structure, and Nowlan recognized that future work might greatly modify the ideas then existing. This has proved to be the case. Subsequent detailed work has established the stratigraphic sequence in the Keewatin formations which are the host rocks of the orebodies, and has shown that the principal orebodies are confined to two adjoining bands of tuff.On this basis, it is now possible to map the complex structures with greatly increased accuracy. The amount of drilling and underground exploration required to find new ore has been much reduced, and indicated ore reserves are now substantially greater than at any time in the past. Daily production in 1955 averaged 187 tons per day at 0.578 ounces of gold per ton.The sequence of Precambrian events in the mine area is summarized in the following table:Intrusion of post-ore dykes.Ore formation.Intrusion of post-faulting, pre-ore dykes.Deformation: folding and shearing; alteration; faulting.Timiskaming sedimentation.Unconformity.Keewatin: volcanics and sediments, host rocks of the orebodies, described in detail in the next section.KeewatinFrom oldest to youngest, the Keewatin rocks in the mine area can be divided into six formations, which have been given local names:“Grey"" LavaA fine-grained dacitic to andesitic lava, amygdaloidal and locally containing well formed pillows. Certain areas are sheared and chloritized to a degree that makes identification difficult. The rocks are carbonatized throughout; the most persistent carbonate veins parallel the upper contact. Thickness more than 1,000 feet. (Minor mineralization, type 1 I -See section on Ore Formation)."

Jan 1, 1949

By H. G. Ames

"The property of Perron Gold Mines, Limited, lies in the southwest corner of Pascalis township, northwestern Quebec. It is approximately 12 miles northeast of the town of Val d'Or.This ground was originally staked by Jack Mathews of Amos in the spring of 1931. Shortly after staking, a quartz vein containing visible gold was uncovered on the south boundary of the property, about 400 feet south of the present shaft. With further prospecting, another spectacular goldbearing vein was found 3,000 feet northwest of the original showing. Subsequently, several programmes of exploration were carried out in search of the main ore zone. By 1933 sufficient ore was outlined to warrant sinking a shaft. The first ore was milled in 1934.Total production from the Perron mine from commencement in 1935 to 1944 has been 317,900 oz. gold having a value of $11,935,106. The average recovery a ton for 1944 was $9.01."

Jan 1, 1954

By Weiren Lin

The Mw 9.0 Tohoku-Oki, Japan earthquake occurred on 11 March 2011 produced a maximum coseismic slip of >50 m near the Japan Trench. To investigate why the plate boundary fault between the subducting Pacific Plate and overriding North American Plate which caused the earthquake had such unprecedented large coseismic displacement and slipped to the trench, Integrated Ocean Drilling Program Expedition 343 called Japan Trench Fast Drilling Project (JFAST) drilled three boreholes at Site C0019 through the earthquake fault about one year after the earthquake. Borehole C0019B dedicated to loggingwhile- drilling (LWD) penetrated ~850 meters below seafloor (mbsf) at a water depth of approximately 6890 m. The plate boundary fault is located at ~820 mbsf in the borehole and has been identified as the slip zone during the Tohoku-Oki earthquake. Borehole wall resistivity images obtained from LWD show that drilling induced borehole breakouts are available in a wide depth range above the fault but are not available below the fault. Breakouts are reliable indicators of the orientations of current maximum and minimum horizontal stresses and can also be used to constrain the horizontal maximum and minimum stress magnitudes. As results of breakout analyses, the maximum horizontal stress orientation highly varied in the upper part of the borehole, but has a clear preferred orientation in a northwest – southeast direction in the deeper part just above the fault. This orientation is approximately parallel to the direction of the Pacific Plate subduction. Stress magnitude constraints indicate that the post-earthquake stress states in the hanging wall are either in or close to the normal faulting stress regime. By inferring the pre-earthquake stress state and comparing with the constrained post-earthquake stress state, a significant coseismic stress change was interpreted. The stress change suggests an active slip of the frontal plate-interface consistent with coseismic fault weakening and a nearly total stress drop.

Jan 1, 2015

By C. J. Sullivan

It is of importance, in prospecting, to distinguish ores of magmatic origin from those derived by the meta-morphism and granitization of source rocks and from those accumulated in certain sedimentary facies. The magmatic ores, which are characterized by their occurrence along fault structures, may be associated with volcanic (including explosive) phenomena. Heat effects are local. The magmatic sequence is well de-fined: kimberlite, with diamond pipes; ijolite, with carbonatites; peridotite, with nickel deposits; norite, with nickel-copper deposits; and diabase-gabbro, with copper-zinc deposits. These deposits are characteristic of Precambrian shields, where a thick sialic crust may rest on basic to ultrabasic magma. The sequence is resumed in the Paleozoic terrains (in a broad sense), with monzonite porphyries and associated copper, copper-gold, and cop-per-lead-zinc deposits.

Jan 1, 1962

By K. Schimann, H. D. Knipping, J. P. Fouques

"The Cigar Lake uranium deposit, in the Athabasca area of north Saskatchewan, was discovered in May 1981 by Cogema (Canada) Ltd., as operator of the Waterbury Lake Joint Venture.The deposit, which is devoid of direct surface expression, is located at the unconformity between the Lower Proterozoic (Aphebian) Wollaston Group meta-sediments and the Middle Proterozoic (Helikian) Athabasca sandstone, at a depth of 410 m to 450 m below surface.At the end of 1984, the deposit had been defined by 105 mineralized holes over a length of 1800 m and a width of between 25m and 105m. It has the shape of flat-lying /em 5 m to 30m thick and shows a remarkable longitudinal and lateral continuity from the information obtained to date. A well defined bulge of the unconformity underlies the mineralized zone over its entire length.The deposit appears to be controlled by an east-west trending structure within which a particular rock facies (""augen gneiss'') has developed in the graphitic metapelites of the Wollaston Group. It is surrounded by a strong alteration halo affecting both sandstone and basement, characterized by extensive development of Mg-AI rich clay minerals (illite-chlorite). The mineralization is hosted principally by the Athabasca sandstone, and consists mainly of uraninite and sulfa-arsenides of nickel and cobalt. Numerous geochemical and geophysical surveys have been carried out in the Cigar Lake area, and although no specific geochemical or geophysical anomaly can be directly associated with the mineralized body, there may be locally a good coincidence.However, a combination of several methods proved extremely useful in interpreting the regional geology and defining the drilling targets within the favourable areas.Although the Cigar Lake deposit shows many similarities with several classical deposits of the Athabasca region, it is characterized by the intensity of its alteration processes and the presence of massive, extremely high grade mineralization.At the end of 1984, the global geological reserves estimated by geostatistics on the main mineralized ""pod"" of the deposit amounted to 110,000 metric tonnes of uranium at an average grade of 12.2% U, with a precision of 25% at the 95% confidence level."

Jan 1, 1986

By A. Allaire

The Goldex operation of Agnico-Eagle Mines (AEM) commenced operations in the spring of 2008. Following some months of initial operation, the grinding circuit capacity was under-performing according to the original design throughput. BBA Inc. (BBA) was commissioned, in February 2009, to study the different options and recommend the quickest and most cost-effective solution to increase the grinding circuit throughput rate. The mandate was to increase the throughput of the grinding circuit to beyond the original design of 7,000 tpd to 8,000 tpd or greater, while retaining the existing SAG and ball mills. The circuit was modelled using JKSimMet software to evaluate the different options, each with a number of different operating parameters. The option of secondary crushing of the SAG mill feed was retained. Comparison of the different options and simulation outcomes, design of the secondary crushing circuit, operating conditions, and initial adjustments in the design and operating results of the new grinding circuit are discussed in this paper.

Jan 1, 2012

By E. C. Keeley

Some Safety Measures at Ontario Mines The following safety precautions have of late been taken by several of the Ontario mines: installation of water crossovers; washing clown of faces to show-up missed holes; insistence on gloves being worn as a protection to men's hands; wearing of safety boots and hats by underground men; and wearing of goggles by all men using hammers, starting holes, etc. In the summer of 1924 the Mclntyre mine began experimenting with means of removing powder smoke from headings by installing fans and pipe-lines of various designs, also with different means of introducing water into the air-blast when blowing smoke. By October of that year they had devised a scheme of water connection between the water and the air line, at a distance of about one hundred and fifty feet back from the face, using two valves and a short hose. By this means a limited amount of water could be introduced into the air which blew into the face, resulting in a fine spray of air and water combined. This spray not only helped to eliminate fumes but also introduced fine particles of water into the air, raising it above the dew point, with the result that when these fine particles of water settled they had attached to them fine dust particles, thus eliminating, to a great extent, the injurious dust caused by blasting. The combined air and water is turned on immediately after blasting and allowed to blow continuously for from four to five hours, until the muckers come on shift.

Jan 1, 1931

By W. R. Lindsay

Anyox, where the Hidden Creek mine of the Granby Consolidated Mining, Smelting and Power Company is located, is situated on an excellent deep-water harbour in Granby bay, at the head of Observatory inlet, about 600 miles from Vancouver and 90 miles north of Prince Rupert. Anyox is the Indian name for the little stream which empties into Granby bay, and means 'hidden creek'. The Ore-Bodies The ore is a replacement deposit and occurs at and near the contact between argillites and a later intrusive greenstone. This contact locally has a general north-and-south trend, an irregular westerly dip, and in the vicinity of the ore-bodies there has been intense folding, accompanied by faulting. The mineralizing solutions supposedly were derived from the Coast Range granite batholith, distant one to two miles to the east and north. The whole area is cut by many dykes of varying widths, which seem to have had but little part in the ore deposition.

Jan 1, 1929

By G. K. Herzog

THE problems relating to the construction and use o{ mining equipment are basically the same as those pertaining to equipment in other industries. It is true that much mining equipment is subjected to an unusually severe combination of shock, high stresses, abrasive wear, and corrosive ? conditions, but in other industries, also, equipment must operate under similar adverse conditions, so that their experiences may readily be applied to the problems of the mining industry. Steel and iron are for obvious reasons the most suitable materials for the construction of the greater part of the equipment used in the mining industry. For a large percentage of uses, the ordinary plain carbon-steels and ordinary or unalloyed cast-iron are, and probably will continue to be for a long rime, entirely satisfactory materials. There are, however, many. conditions which cannot be satisfactorily taken care of by these materials, and alloy steels and irons must be used where the greatest possible economy is desired. In general, alloy steels and irons are used where it is necessary or economically desirable to use materials possessing properties superior to plain carbon-steel or ordinary cast-irons, such as: (a) better strength (b) better wear resistance (c) better corrosion resistance (d) better resistance to high temperatures (e) better resistance to low temperatures or combinations of two or more of these advantages. There are also conditions where materials having other special properties are required, such as, for example, certain magnetic or electrical properties for electrical machinery; but in the great majority of cases, one or more of the five advantages listed are the most desired.

Jan 1, 1938

By S. Torizuka, I. Mizushima. Kawasakitohri, A. Ohmori, K. Nagai

Strain (work)-hardening in tensile tests were examined for low carbon steels with various ferrite grain sizes ranged from 0.4µm to 16µm. The steels had microstructures composed of ferrite grains and dispersed cementite particles. They were fabricated through warm caliber rolling with an accumulative area reduction of 93%. Strain-hardening rate at a given strain increased with an increase in volume fraction of cementite particles. The balance of yield strength and uniform elongation for ultrafine-grained structures could be improved by the dispersion of cementite particles. Effects of the cementite dispersion and the ferrite grain size on the strain-hardening rate can be roughly explained by the work-hardening model with GN-dislocation density. Strain-hardening design using dispersed cementites was proved to be effective in controlling ductility of the ultrafine-grained steels.

Jan 1, 2004

By Nigel Saunders, Zhanli Guo

"Quench sensitivity of heat-treatable aluminium alloys is closely related to the precipitation process taking place during quenching. Faster cooling results in less precipitation of coarse phases during cooling, leaving more solutes in the solution before ageing. An alloy in such state would be of greater hardening potential as larger amounts of hardening phases may precipitate out during ageing. Hence, to understand the quench sensitivity of an alloy, it is essential to understand its precipitation process. Precipitation is a diffusion-controlled process and the diffusion is made complicated by the so-called quenched-in vacancies. These vacancies form during solution treatment, become “excess” when temperature goes down, and annihilate during the following cooling and ageing treatments, making diffusion now a function of both temperature and time. This paper first investigates the formation and annihilation of quenched-in vacancies and their effect on diffusion. The diffusion affected by quenched-in vacancies is considered in the kinetic models to realise the calculation of TTT/CCT diagrams for aluminium alloys. The calculated CCT diagrams have been used to explain the observed quench sensitivity and age hardening behaviour of various commercial alloys. The transformation from GP zones to other hardening phases during ageing is also discussed.INTRODUCTION The heat treatment of aluminium alloys mainly consists of three stages: a solution treatment at an elevated temperature, quenching from this solution treatment temperature to room temperature, followed by an ageing treatment to allow the precipitation of strengthening phases(Davis, 1993).The following statements generally describes how quench sensitivity is observed in heat-treatable Al-alloys: faster cooling results in,(i) less precipitation of coarse phases formed at high temperature during cooling, (ii) more solutes kept in solution before ageing, and (iii) larger amounts of hardening phases being formed, i.e. a greater hardening potential. Thus, the quench sensitivity of an alloy is closely related to its precipitation kinetics."

Jan 1, 2018

By Huan-Qiang Zhang, Gang-Hai Huang, Yu-Yong Jiao, Fei Zheng, Zhang. Xiu-Li

An efficient and accurate three-dimensional (3-D) contact detection algorithm is of vital importance in large-scale computing of discontinuous deformation analysis. The contact detection algorithm takes up a large proportion of the whole calculation time because of the increasing calculation number in three-dimensional case. For block systems which consist of convex polyhedrons, the efficiency and accuracy of the contact detection algorithm is a great challenge. The presented contact detection algorithm in discontinuous deformation analysis (DDA) method is carried out in three phases: the global neighbour searching, the local contact type searching and the contact transferring. A contact detection algorithm for 3-D DDA is presented with some improvements on the three phases. A grid-based global neighbour searching algorithm is used to eliminate unnecessary neighbour blocks to the exact number. The local contact type searching includes two steps. In the first step, the common plane method is used to determine the contact type between convex polyhedrons. In the second step, the contact pairs detected by the common plane method are divided into four basic types. In the third phase, the four contact types are transferred into two basic contact types, vertex-to-face contact type and edge-to-edge contact type, which are managed in a uniform procedure. Three verification examples are calculated, the results show that the proposed algorithm based on the three contact detection phases is robust and efficient.

Jan 1, 2015