Search Documents

By S. Banisi, J. A. Finch, A. R. Laplante

"A technique for on-line simultaneous estimation of gas and solids holdup (volume fraction), based on a combination of conductivity and pressure difference measurements, is proposed and tested in a laboratory flotation column (10cm in diameter and 447cm in height). Fundamental concepts underlying this technique and the effect of relevant parameters are discussed. In the studied range, 3-30 %v/v gas holdup and 2-18 % v/v solids holdup, experimental results showed good agreement between the estimated and actual holdup values (as determined by an isolating technique). The relative accuracy of the solids holdup estimation increased when solids density or solids concentration increased. Frequent re-calibration of pressure transducers was found necessary for accurate phase holdup estimation.IntroductionGas holdup is a key parameter in controlling the performance of flotation columns. For example, flotation rate is affected by bubble size and gas rate both of which, in turn, affect gas holdup. Moreover, gas holdup also determines the slurry residence time which indicates a direct influence of gas holdup on recovery.Gas holdup determination has been the focus of many studies (e.g., Castillejos, 1986; Marchese et al., 1992). Some of the techniques which have been used are given in Table 1."

Jan 1, 1994

By L. T. Munn

"IT IS NOT necessary here to dwell on the fact that sulphur is currently in short supply. It may be well, however, to •point out that this •storage is not merely a temporary condition, but that, judging by trends in world consumption of sulphur, it may •be anticipated that requirements will double in the next ten years.Even with improved techniques for mining elemental sulphur in the United States and the new finds in Louisiana, there is much concern as to how these future sulphur requirements can be met. It appears necessary to .turn more and more to other sources than elemental sulphur for •additional production. The three major alternative sources were:(1) By-product sulphuric acid •from smelter gases.(2) Sulphur and sulphuric acid from iron sulphides.(3) Sulphur from hydrogen sulphide contained in natural gas. The Jumping Pound sulphur plant of the Shell Oil Company of Canada, Limited, is designed to produce sulphur by the •third of these methods.Jumping Pound is a natural gas field about 20 miles west of Calgary where Shell has a number of producing wells."

Jan 1, 1952

By W. B. Xie

The hardening behaviour and microstructure evolution of Cu-30Ni-30Mn alloys aged at 350 °C has been investigated utilizing optical microscope, scanning electron microscope, transmission electron microscopy and Vickers hardness tester. The results show that the discontinuous precipitation of NiMn phase results in a remarkably hardening effect in Cu-30Ni-30Mn alloy during aging at 350 °C. The maximum hardness (~494HV) is attained in the sample after aged for 48 h. The NiMn precipitates are ordered and have a face-centered tetragonal structure. The coherent orientation relationship between the NiMn precipitates and Cu matrix is (220)Matrix // (220)P, [1-1-2]Matrix // [1-1-2]P. In addition, there is a linear relationship between hardness and volume fraction of the discontinuous precipitation, which indicates that the hardness increment of Cu-Ni-Mn alloys aged at 350 °C is attributed to the microstructure characteristics of discontinuous precipitation. The high strength of discontinuous precipitation colony is caused by the formation of nanoscale NiMn precipitates with a lamellar structure in discontinuous precipitation. INTRODUCTION Cu-Ni-Mn alloys are attractive candidates for oil drilling, aerospace and energy applications due to their high elasticity, high strength and excellent corrosion resistance (Sun et al., 2009; Liu, Yang, Xia, Jiang, & Gui, 2016). The high strength of the Cu-Ni-Mn alloys is mainly attributed to the precipitation of NiMn phase (Shapiro, Tyler, & Lanam, 1974; Xie et al., 2015). The uniformly dispersed nanoprecipitates formed by continuous precipitation can impede dislocation movement, and thereby lead to a significant improvement in strength of traditional precipitation-strengthened alloys. However, it is reported that there are two precipitation types observed in Cu-Ni-Mn alloys, namely, continuous precipitation and discontinuous precipitation (Shapiro et al., 1974). The discontinuous cellular colony with a lamellar structure nucleates at grain boundaries, and progressively grows inward the grain on the process of discontinuous precipitation (Ng, Bettles, & Muddle, 2011). It is found that the discontinuous precipitation can occur in many Cu-based alloys, such as Cu-Ni- Mn alloy (Shapiro et al., 1974), Cu-Be alloy (Monzen, Hasegawa, & Watanabe, 2010) and Cu-Ni-Sn alloy (Zhao, & Notis, 1998). Many studies consider that the discontinuous precipitation results in a detrimental effect on hardness and strength, and the discontinuous precipitation occurring during aging treatment should be suppressed (Markandeya, Nagarjuna, & Sarma, 2004; Semboshi, Sato, Iwase, & Takasugi, 2016). The mechanical properties can also be improved by discontinuous precipitation in AZ91 magnesium alloy (Tamura, Kida, Suzuki, & Soda, 2009) and AM30 magnesium alloy (Saikawa et al., 2012). Jun (2017) found that the reduced interlamellar spacing of precipitate fibers in discontinuous cellular colony leads to a significant increase in hardness. Indeed, the strengthening contribution of discontinuous precipitation is similar to that of continuous precipitation in Cu-20Ni-20Mn alloy. Discontinuous precipitation of NiMn phase can provide a significant strengthening effect in Cu-Ni-Mn alloys.

Jan 1, 2019

By B. R. Rakishev

Balanced development of mining works at all the benches of a working zone by use of the excavator-automobile complex is achieved by transition to the technology of the bench excavating with cross panels by the two-sub-bench scheme with the changing levels of the working platforms (is patented in Kazakhstan). In deep quarries realization of this technology will allow to reduce the current volumes of the stripping ore excavation by 10?15 % and more, to increase the opened reserves of minerals by 20?50 % to decrease volume of mining-capital works for construction of stripping excavations by 2?4 times and to provide efficient use of powerful excavator-automobile complexes.

Aug 1, 2013

By C. A. Morais, L. V. Resende

"The technological development observed in recent years has stimulated the application of rare earth (RE) elements. Amongst their various applications it is well worth mentioning their use in electronics, superconductors, nuclear medicine, as well as in special inks - as those used in radar invisible airplanes. TV and computer monitor screens present as coating a powder containing some rare earth elements, mainly Europium and Yttrium. The recovery of the RE elements from electronic scrap is extremely important as the economic and environmental issues are concerned. This paper describes the study of the Eu and Y recovery from e-scraps. The first step of the process was the leaching of the powder obtained by manually scraping the inside surface of the screen. After the optimization of the leaching, the dissolution of Eu and Y was higher than 98 w/t% and a pregnant sulfuric liquor containing 11.9 g L-1 Y and 0.72 g L-1 Eu was obtained. The second step was the separation of the metals found in the liquor by the solvent extraction technique. The separation of Eu and Y was carried out in a counter current circuit compound of 3 extraction stages, 7 scrubbing stages and 15 stripping stages. DEHPA was used as the extractant, whereas a diluted sulfuric acid solution was applied as scrubbing agent and a hydrochloric acid solution at high concentration was used as the stripping agent.INTRODUCTIONThe rare earths (RE) are a moderately abundant group of 17 elements composed of lanthanides, scandium and yttrium. Amongst the RE, promethium (Pm) is extremely rare, however several of the RE elements are not very rare and occur dispersed in a variety of forms (Greenwood & Earnshaw, 1984; Tyler, 2004).The innumerable applications of the RE elements are based on their particular properties, mainly their spectroscopic and magnetic properties (Martins & Isolani, 2005). The technological development observed in recent years has stimulated the application of rare earth (RE) elements. They have been used in agriculture, electronics, superconductors, nuclear medicine, automobile industry, special inks – as those used in radar invisible airplanes, X-ray screens, high intensity mercury vapour light bulbs, neutron scintilators, charged-particle detectors and optical memory reading systems (Maestro & Huguenin, 1995; Nagaosa & Binghua, 1997; Sánchez et al., 1999)."

Jan 1, 2012

By S. C. Ells

Introduction An investigation of the bituminous sands of Alberta was begun by the Mines Branch, Department of Mines, in 1913. This investigation was interrupted during the period 1916-19, but was resumed in 1920. Work completed in October 1924 has included detailed topographical surveys of extensive areas, examination and sampling of principal outcrops, the mining of trial shipments, laying of demonstration pavements, and a study of methods adapted to the recovery of hydrocarbons from the crude bituminous sand. Bituminous sand consists, for the most part, of clear quartz grains, cemented together by petroleum residuum or bitumen. In form the quartz grains are most irregular, varying from sharply angular to smooth, waterworn shapes. The bitumen has a specific gravity of 1.018 and has a penetration of 9.00 mm. (77° F. 100 grams 1 sec.). The percentage of bitumen associated with the sand varies from 5 to 25 per cent. A large tonnage is available in which the percentage of bitqmen is 15 per cent or over. Production Up to the present time, production has been restricted to requirements for experimental .and demonstration work. The total quantity shipped for such purposes has not exceeded 750 tons.

Jan 1, 1925

By C. R. Ross

"The purpose of this paper is to review the activities of international organizations concerned with the problem of dust hazards in mines and to indicate the extent of Canadian participation in these activities. The work of the International Labour Office in sponsoring conferences and reports on the appraisal and control of dust hazards and in the development of standard radio-logical classifications is considered in some detail. Also discussed are the role of technical societies, such as the American Conference of Government Industrial Hygienists, in the development of proposed standards for dust exposure and the functions of international committees concerned with particular hazards, such as the U.I.C.C. (Inter-national Union Against Cancer) Committee on Asbestos and Cancer."

Jan 1, 1969

By S. Kashani Nejad, M. Bellino, K. Collins, C. Tovee, J. Godwin

Motivated by safety considerations, logistical issues, transportation cost savings, product diversification, and marketing preferences, several uranium producers are revisiting their business models and supply chain configuration and, instead of selling dried yellowcake to downstream refineries, they are moving to build in-house calcining facilities. Drying and calcining plants are relatively low-cost facilities to build and operate. The execution period of a typical yellowcake drying and calcining project is also relatively short and alternative construction methodologies, such as modularized solutions, are available. The drying and calcining technologies used for yellowcake are relatively mature, environmentally contained, and well supported by qualified vendors. The drying and calcining circuits also seamlessly integrate with upstream and downstream operations. These either produce a dried yellowcake or calcined U3O8 which are notably safer and easier to transport and market. This paper presents an overview of the recommended technology and project development considerations for yellowcake drying and calcining facilities.

Jan 1, 2020

By K. Shen, A. J. Sinclair, N. Champigny

"Fluid inclusion studies from the Cinola deposit indicate low salinities and low C01 contents of the ore fluid. This supports a suggestion that the mineralizing fluids originated from pore water in the fluviatile host rock (mid-Miocene Skonun Formation). Bimodal distribution of filling temperatures suggests the existence of at least two temperature regimes centred on 160°C and 270°C during mineral deposition. Independent age and stratigraphic evidence indicates that depth of mineralization is between 1.1 and 1. 8 km, corresponding to a hydrostatic load of between 110 and 170 bars.RESUMELes donnees sur les inclusions fluides du gisement Cinola indiquent de basses salinites et basses teneurs en C01 . Ceci confirme que les fluides mineralisants ont ete derives de l'eau interstitielle prise dans les sedimentsfluviatiles hates. La distribution bimodale des temperatures d'homogenisation implique !'existence de deux regimes de temperature concentrees vers 160°C et 270°C pendant Ia mineralisation. La profondeur alaquelle le gisement s'est forme est evaluee d'etre entre 1.1 et 1.8 km a partir d'informations stratigraphiques independantes: ceci correspond a des pressions hydrostatiques de 110 a 170 bars."

Jan 1, 1982

By Olav Mejia

The rising energy costs and environmental considerations in mining necessitate the development of energy-efficient copper and gold processing plants. This paper presents an analysis of technical strategies aimed at reducing energy consumption in these plants. Key approaches include the integration of advanced ore sorting technologies, High Pressure Grinding Rolls (HPGR), Coarse Particle Flotation (CPF), and high-intensity flotation. Ore sorting enables early-stage waste removal, reducing the downstream processing load and associated energy use. HPGR technology, recognized for its energy efficiency, contributes to significant energy savings in comminution circuits by reducing reliance on traditional grinding methods. CPF technology further optimizes flotation performance by enabling the recovery of larger particles, thereby decreasing the need for fine grinding and reducing overall power demand. High-intensity flotation units enhance separation efficiency and mineral recovery in a compact footprint, offering further reductions in energy consumption. Together, these technologies provide energy saving opportunities to achieve a more sustainable and economically viable processing operation. This paper evaluates the effectiveness of each method, highlighting their potential impacts on energy consumption, operational efficiency, and cost-effectiveness in copper and gold processing

May 4, 2025

By J. Bigu, M. G. Grenier

"Dust size distribution and aerosol size distribution measurements have been carried out in several Canadian underground uranium mines. In addition, dust samples have been analyzed for long-lived radioactive products of the U-238 and Th-232 natural decay chains using ex-spectroscopy and -y-spectroscopy techniques.From the data collected one may summarize: (a) most airborne particulates are of size below I u-m and 50% by mass are found above 1 u-m; (b) dust clouds are bimodal; (c) preferential deposition of radon (thoron) daughters takes place on airborne particulates in the sub -micron range at about 0.1 u-m; (d) deposition of radon (thoron) daughters is proportional to particle surface area; and (e) ex-spectroscopy and -y-spectroscopy of dust samples reveals the presence of U-238, Ra-226 and some of their short-lived and long-lived decay products.IntroductionExtended inhalation of airborne radioisotopes poses a potential health problem to occupational workers. Because of this, monitoring of radiation and dust levels for dose exposure calculation purposes is not only recommended but in most cases mandatory.CANMET (Energy, Mines a nd Resources Canada) has long since been engaged in a comprehensive monitoring program aimed at determining dust concentrations in the respirable size range, aerosol concentration in the sub-micron range, and in the radioactivity associated with these particulates in underground uranium mines. Measurements have been carried-out with gravimetric dust samplers, dust size selectors (including a horizontal elutriator , a fineparticle spectrometer and Nuclepore* filters of different pore sizes) and a condensation nucleus counter(1 – 6). Inactive and active working sites have been monitored according to some typical mining operations. A summary of these data has been given elsewhere(3- 5)."

Jan 1, 1984

By G. A. Highcock

"Operations started at BCL in December 1973J and the smelter is currently in the seventh year of its fifth campaign. The next major shutdown is scheduled for 1995. During the current campaign, a number of major on-line refurbishments have been carried out without any significant disruption to production. These include the complete rebuild of both drying plant electrostatic precipitators, the installation of a new electrostatic precipitator at the flash furnace, the conversion to a distributed control system throughout the smelter, and the installation of a converter air blowing control system.IntroductionBCL Limited operates a nickel-copper mine in northeastern Botswana approximately 100 km southwest of Francistown. Surface operations for the production of high-grade nickel-copper matte at a design capacity of 42 000 metric tonnes per annum, were commissioned in December 1973. Detailed descriptions of the mine and surface facilities have been presented previously(1-3).Over the years, a number of major engineering modifications and metallurgical projects have been carried out to overcome operating difficulties. improve metal recoveries, increase production rates and provide a better working environment.One of the major results of these projects was an increase in the 19805 in flash furnace feed capacity from 70 t/h to 120 t/h of new concentrate with a nominal feed rate of 105 t/h being achieved.(4)Because of the ore characteristics, i.e. a high mass fraction of ore reporting to concentrate, BCL operates one of the highest capacity spray drying plants and flash smelting furnaces in the world(5).A schematic of the BCL smelter is shown in Figure 1. The smelter is now in the seventh year of its fifth campaign, with the next shutdown scheduled for mid-l99S. In this campaign, the following major projects were completed:"

Jan 1, 1995

By Simon P. Fricker

Gold drugs have been used for the treatment of rheumatoid arthritis since the mid 20th century as disease-modifying antirheumatic drugs (DMARD) class. Methotrexate is often the preferred DMARD, and with the advent of new therapies gold drugs are now used infrequently. Since the introduction of auranofin in 1985 there has been no new clinically approved gold drug. In spite of this apparent lack of progress there has been a great deal of interest in the use of gold compounds for cancer therapy and early promising indications were achieved with a gold phosphine complex [Au(dppe)2]Cl. This compound was not entered for clinical trials, however, due to problems with cardiotoxicity highlighted during pre-clinical toxicology studies. Gold(III) is isoelectronic (d8) with platinum(II) and likewise forms square planar complexes. It is therefore tempting to speculate that such complexes would have similar antitumor activity to cisplatin. In order to stabilise the gold(III) oxidation cycloaurated complexes were synthesised with a single mononegative bidentate ligand, damp, (2-[(dimethylamino)methyl]phenyl), and two monodentate anionic ligands e.g. Cl or acetate. The damp ligand forms part of a five-membered chelate ring. The monodentate ligands are readily hydrolysed and are available for substitution. These compounds had limited anti-tumor activity in in vivo against human tumor xenografts. Mechanistic studies indicated that these compounds had a different mechanism of action to cisplatin. An alternative molecular target for these compounds is biologically important thiol-containing molecules such as the cysteine protease cathepsin B. Modifications were made to the Au(III) damp structure to give compounds with a six-membered chelate ring. These compounds were shown to be inhibitors of cathepsin B. Compounds were also tested for cytotoxicity against a panel of human tumor cell lines. Three compounds were selected for further evaluation against a human colon tumor xenograft. The compounds showed modest anti-tumor activity but with no marked improvement over the parent Au(III)damp complexes. Initial indications are that Au(III) compounds targeted against disease-specific thiol-containing biological molecules have potential as drugs, particularly for cancer. However, further work is required to produce a target-specific drug with a suitable pharmacological activity and toxicity profile.

Oct 1, 2003

By J. R. Maxwell

In 1970 expansion was completed increasing mill capacity from 2,000 to 3,000 T.P.D. Actual grinding capacity is 3,400 T,P,D. at a grind of 60% -200 mesh,The ore bodies are vein type, containing about 12% sulphides, with mill heads averaging 2.25% Cu, 0.015 oz.Au, and O.4O oz, Ag. per ton.Summary and Conclusions:During the period Jnnuar-1 1971 to December 1973 inclusive the use of large cells at Opeminka have shown that metallurgy is comparable to when using conventional cells, Operating and maintenance costs are lower, An on stream analyzer with reagents controlled by computer, are being assessed further.Opej1atljn Of Cells:!lo cell level adjustments are required when tonnage is adjusted 20 to 25%.Depending on mill heads and grade of concentrate reagents are adjusted to the first rougher for metallurgical control. Reagents to second rougher and scavengers are seldom adjusted as feed to this section has a maximum variation of about 0.2'~ Cu.Power – Maintenance and Space Requirement :Our total power consumption for 3,400 T.P,D. flotation circuit for operation and air supply is 280 H.P. Previous power drawn using conventional cells was 400 H.P. at 2,000 T.P.D.Total maintenance costs for flotation circuit has averaged $1,100.00 per year for the 3 years of operation, this cost should remain constant.Floor space required for cells and walkways is 2,000 sq.ft.

Jan 1, 1974

By Steven R. McCutcheon

"The Bathurst-Newcastle district, a subcircular area approximately 50 km in diameter, contains 37 massive-sulfide Zn-Pb-Cu deposits that have defined tonnages, and has 58 additional significant occurrences. The largest deposit is Brunswick No. 12, with total reserves (including past production) of 148 million tonnes grading about 12.5% combined Pb-Zn. The deposits/ occurrences are spatially associated with a felsic volcanic pile that contains a significant sedimentary component. In the vicinity of the Brunswick deposits the pile is divisible into lower and upper sequences. The lower is characterized by megacrystic rhyolite (QFAS) and coarse- to fine-grained quartz (± feldspar) wackes and/or tuffites (QAS); the upper sequence is characterized by aphyric to sparsely porphyritic rhyolites (HWR), micro-breccias, and acid hyaloclastites with interbedded dark gray sedimentary rocks. A greenish gray to dark gray siltstone (GGS) separates the two sequences and hosts the sulfide deposits. Lithogeo chemistry of least altered samples shows that the QFAS and HWR have an igneous character, whereas the QAS and GGS have a sedimentary signature. The two types can be distinguished on the basis of total alkalies (Na2 + K2O) versus SiO2/Al2O3 and Ti02 versus Fe/(Fe +Mg). Some trace elements, such as Sr and Y, also help differentiate the two types. The QFAS differs from HWR by having higher La/Yb ratios but lower Zr and Th. The Bathurst deposits do not show a close spatial association with rhyolites but rather are stratiform bodies Oacking clastic textures) within fine-grained sedimentary rocks. The scarcity of barite and other sulfates indicates that there was little mixing between the metal bearing fluids and cold seawater. High Fe/(Fe+Mg) ratios in chlorites also indicate the fluids did not contain a significant seawater component. These features and the large size of many deposits suggest that the deposits formed from metal-rich pore waters that were released catastrophicallyfrom an acquifer in the footwall stratigraphy."

Jan 1, 1992

By G. Begin

"The expansion undertaken at Selbaie in 1985 necessitated an adaptation and expansion of the equipment maintenance system. This paper relates briefly the stages of transformation of the maintenance administrative structures, work methods and tools. The maintenance in a mechanized mine requires an expenditure level in the order of 20% of the total operating cost of the enterprise. Thus, the maintenance organization was modified to apply more computerized planning and follow-up, and the role of preventative maintenance was further advanced.IntroductionAs far as maintenance is concerned at Selbaie, the scenario described herein is a resume of the current situation. Although positive results have been obtained, this outline is in no way a detailed account of a fail-proof maintenance system.Once zone A-I was put into production, the expansion the mine experienced in 1985 had a direct impact on the equipment maintenance system. As centralized as it was in the beginning, the system is now partially decentralized.The over-all changes to the maintenance department demonstrate the flexibility required by organizations in new situations. In spite of the exceptional results obtained before the expansion, it became evident that both the maintenance and production sectors would have to be combined. In doing so, a more appropriate coordination of maintenance work could be obtained and the maintenance staff would obtain a more detailed knowledge of the equipment in each sector. In addition, by keeping the general and specialized departments centralized, it was possible to offset the negative effect s of a decentralized system, namely too much manpower."

Jan 1, 1990

By Peter Rubie

"For many years, optimising the relining of hard rock grinding mills has been complicated by:?? the large number of variables;?? the low frequency of relines (slow feedback loop);?? the potential economic risk associated with some changesA technology that has its roots in the automotive manufacturing industry is being utilised to construct a statistically accurate, configurable, and dynamic simulation of the mill relining process. The effects of various mechanisation and process changes can be rapidly modelled and compared.This technology will provide mill maintenance managers and contract relining companies with the opportunity to benchmark current performance against world’s best practice. It will also provide an opportunity for concentrator plant designers and mill manufacturers to plan for maximum plant efficiency, by designing an infrastructure and equipment combination that maximises annual plant availability.This simulation tool and its associated data set, has been developed using recent grinding mill performance data from mills of varying dimensions, liner configurations, mill relining equipment, operator and tool variables.The simulation will provide an output that the various stakeholders can utilise to make optimal decisions within the given financial, physical and technological constraints of the individual concentrator plant."

Jan 1, 2012

By C. W. Hancher, B. D. Patton, W. W. Pitt

"There are a number of nitrate-containing wastewater sources, as concentrated as 30 wt % NO3 and as large as 2000 m3/day, in the nuclear fuel cycle. The biological reduction of nitrate in waste water to gaseous nitrogen, accompanied by the oxidation of a nutrient carbon source to gaseous carbon dioxide, is an ecologically sound and cost-effective method of nitrate waste disposal. These nitrate-containing wastewater sources can be successfully biologically denitrified to meet discharge standards in the range of 10 to 20 g N(NO3-)/m3 by the use of a fluidized bed bioreactor. The denitrification bacteria are a mixed culture derived from garden soil; the major strain is Pseudomonas. In the fluidized-bed bioreactor, the bacteria are allowed to attach to 0.25- to 0.50-mm-diam. coal fluidization particles, which are then fluidized by the upward flow of influent wastewater. Maintaining the bacteria-to-coal weight ratio at approximately 1:10 results in a bioreactor bacteria loading of greater than 20,000 g/m3,This paper describes the results of a bio denitrification R&D program based on the use of fluidized bioreactors capable of operating at nitrate levels of up to 7000 g/m3 and achieving denitrification rates as high as 80 g N(N03-) per day per litre of empty bioreactor volume. IntroductionThe discharge of wastewater containing nitrate at concentrations greater than stipulated by the Environmental Protection Agency (EPA) creates an environmental hazard and constitutes a civil and/ or criminal legal liability.(I.2) At present, we have three options: (1) recycle and reuse of nitrate streams the total economic and technical balance should be Closely examined; (2) use of an alternative acid, which may pose an entirely different set of problems ; or (3) disposal of nonreusable nitrate sources by an environmentally acceptable procedure."

Jan 1, 1980

By D. W. Li

Due to the ultrasonic testing and mechanical wind speed sensor have high requirement for the environmental of the coal mine, the charge induction wind speed detection method based on wavelet analysis is proposed. The same wavelet disturbance detection method is used at a fixed distance to obtain an induction signal to obtain a pass time, and then calculate the magnitude and speed of the wind. Simulation and verification experiments show that the method has application across a wide range of test speeds (up to 60 m/s). The metal probe causes little pipeline flow field interference. The method is particularly well-suited to dusty environment, and does not cause dust deposition through long-term operation. It can be widely used in coal mines for point wind speed continuous online testing.

Aug 1, 2013

By H. Deveci, E. Y. Yazici, A. D. Bas

The leach solutions of waste of printed circuit boards (WPCB) may contain a wide range of base and precious metals with different concentrations due to heterogeneity of these wastes in composition. Therefore, selection of a suitable metal recovery method is of practical importance for downstream processing of pregnant leach solutions of WPCB. Sulphuric acid leaching of WPCB in the presence of a suitable oxidant is capable of dissolving base metals as well as precious metals such as silver. In this study, cementation of silver from sulphuric acid leach solutions of WPCB using metallic copper, aluminum and zinc was studied. The WPCB sample was assayed to have a silver content of 694 g/t. A synthetic leach solution containing 20 mg/L Ag in sulphuric acid solution (0.51 M H2SO4) was prepared based on the silver concentration in pregnant leach solutions of oxidative sulphuric acid leaching tests. Total sulphate concentration ([SO4 2-]T) was kept constant using sodium sulphate at 1 M. Metallic powders of copper (-850 +600 µm), aluminum (-425 +45 µm) and zinc (-45 µm) were used in the cementation tests. The effects of metal type (Cu, Al or Zn), dosage of metal powders (above the stoichiometric ratio by up to 2000-fold) and temperature (20-80°C) on the rate and extent of silver extraction from the solution was investigated. The effect of presence of copper on the cementation performance was also tested. Under suitable conditions high silver recoveries (>90%) was achieved using metallic copper and zinc while aluminum yielded the lowest silver recovery (i.e. 40% Ag). The kinetics of cementation by zinc was comparatively higher than that of other metals. Increasing the temperature was observed to significantly enhance both the rate and extent of silver cementation. SEM-EDS studies were performed to characterise the metallic powders after cementation.

Jan 1, 2016