Search Documents

By Haofeng Xie, Lijun Peng, Xujun Mi, Xue Feng, Xiangqian Yin, Zhen Yang, Guojie Huang

The Cu/Al composite wires have been widely used in cable industry. Especially in the development of aerospace, the light weight character of wires is particularly important. The wires are fabricated by a drawing process and heat treatment. Mechanical and electrical properties are measured and analyzed. The bending behavior is studied by scanning electron microscope. INTRODUCTION Cu/Al composite is a typical bimetallic composite that has been used in plenty of fields such as automobile and aerospace. The composite has the advantages of excellent conductivity as well as low weight, which cannot be obtained from single copper or aluminum. Industrial products of Cu/Al composite include Cu/Al composite joints (Uscinowicz, R., 2013), Cu/Al bimetallic sheets (Li, X. et al., 2011), Cu/Al flat bar (Wu, Y. & Liu, X. & Xie, J., 2014) and CCA wires (Ahmed N., 1978). CCA wires refer to the composite wires that copper layer concentrically coated on the surface of aluminum core conductor, implementing solid combination of two metals on the interface and forming an integral. At present, the aircraft cable generally use copper or copper alloy conductor, which makes the wire in the aircraft occupy a considerable proportion due to the large density of copper. Therefore, the use of Cu/Al composite wires instead of copper wires for weight loss, is of great significance to the development of aerospace technology industry. Heat treatment is an indispensable procedure to improve plasticity during cold working process, which is of great importance to preparation of wires (Wang, Q. et al., 2008). During the heat treatment, the Intermetallic Compounds (IMCs) are inevitable formed at the contact area of Cu/Al due to the occurrence of diffusion (Lee, S. et al., 2012). According to the results of former researchers, kinds of IMCs were discovered. Antoine Gueydan (2014) identified the formation of three IMCs (Al2Cu, AlCu, and Al4Cu9) at the interface between copper and aluminum after thermal aging. IMCs have a significant effect to the properties of Cu/Al wires. Bending performance is a vital property for the actual application of wires. The brittle IMCs may create a stress concentration that can cause crack initiation during bending process. This work focus on the mechanical properties of Cu/Al composite wires after heat treatment. The effect of various annealing condition on mechanical and electrical properties are studied, in order to find the appropriate annealing conditions, which produce optimal combination properties of Cu/Al clad composite wires. Bending fracture of composite wires is discussed by morphology observation.

Jan 1, 2019

By B. Dyck, L. Verhelst

"Colloidal silica in Key Lake’s Solvent Extraction (SX) feed solutions has presented an operational problem for the mill throughout its history. The colloidal silica stabilizes aqueous continuous emulsions, resulting in elevated solvent losses and operational downtime. Through the years, many attempts have been made to solve this problem, but no viable solutions were found. By revisiting an idea dating back to the 1979 feasibility study and re-evaluating it under current operating conditions, a practical solution was achieved. This paper discusses Key Lake’s history around colloidal silica removal, starting with coagulation using a polyethylene oxide polymer (PEO), and ending with coagulation using a polyethylene glycol (PEG) polymer. The results of a mill trial using POLYSIL® RM1250 introduced at doses up to 300 ppm into the counter current decantation (CCD) circuit to clarify SX feed solutions are discussed with a focus on the benefits to SX.INTRODUCTION Colloidal silica has historically been a significant operational problem in the Key Lake mill. Silica originates from clays in the ore as well as concrete backfill intermixed with the ore resulting from the mining method used at Key Lake’s ore source, the McArthur River mine. The silica is dissolved as silicic acid into solution in the mill’s sulphuric acid leaching circuit. Once in solution, silicic acid polymerizes (Hearn, Smethurst, & Boskovic, 2016) forming a fine suspension of stable colloidal particles. These silica colloids are unaffected by flocculants and sand filtration reporting to the pregnant leach solution (PLS) as a fine turbidity in solution. Silica concentrations typically ranged from 700 to 1200 mg/L Si in the PLS fed to SX. Throughout Key Lake’s history, silica interactions in the Solvent Extraction (SX) process have made SX a mill bottleneck and a source of significant reagent costs."

Jan 1, 2018

By E. Ghali, C. Su, G. Houlachi

"The influence of lead ions on zinc electrowinning process was investigated by means of electrochemical noise measurements (ENMs) and cyclic voltammetry in conjunction with scanning electron microscopy and X-ray diffraction. All electrochemical experiments were performed in sulphuric acid electrolyte containing different lead ion concentrations as impurity. Lead was added in six trace levels between 0.05–0.8 mg/L in the bath. The lead content of the zinc deposits was dependent on the introduced lead concentrations. The overpotential associated with zinc electrodeposition shifted to higher values with the increase of lead concentration in the solution. An appropriate correlation was found between the different concentrations of lead in the electrolyte and the morphology of zinc deposit by ENM. The results showed that the increase of lead ion concentrations is generally accompanied with the decrease of skew and increase of kurtosis values that could be related to the morphology of zinc deposit. Effectively, the morphology changes from well-defined hexagonal platelets to large hexagonal, layered platelets and finally to non-symmetric refined crystalline structure, respectively.INTRODUCTION In commercial zinc electrowinning, zinc oxide is leached from the roasted calcine with an aqueous acid sulfate electrolyte. Then the zinc-rich solution is purified and transferred into an electrolytic cell. During electrolysis, zinc is deposited on aluminum cathode where lead-silver or pure lead is served as anode. Electrodeposition of zinc could be influenced by several parameters such as bath acidity, temperature, current density, the nature and concentration of impurities as well as additives in electrolyte. Metallic impurities play a complex role during zinc electrowinning and they can adversely"

Jan 1, 2016

By M. Korchynsky

"The key words which characterize vanadium are: unlimited availability, versatility of applications and price stability. The supply of vanadium is assured by diversified sources, distributed all over the globe. The inexhaustible raw materials base is complemented by a strong vanadium industry. Both the fully integrated vanadium producers and converters of vanadium oxide or vanadium-containing slags or residues guarantee an adequate supply, commensurate with the steady growing demand.The major share of the world's vanadium output is being consumed by the steel industry. As an additive to steel, the versatility of vanadium is particularly impressive. A few hundreds of one per cent of vanadium convert plain carbon steel into high-strength, low-alloy steel with more than double strength. On the other extreme, high-speed steels made via the powder metallurgy route show superior performance with vanadium additions as high as 6 or 8 percent. Vanadium is used as a cost-effective alloying addition in steels for high-temperature service, fully alloyed heat-treatable steels, new dual-phase steels for automotive components, rail steels, etc., to mention only a few applications. Vanadium is also an established essential addition for titanium alloys. The chemical industry is relying on vanadium compounds as important catalysts.In spite of a wide diversity of applications and continual growth in consumption, vanadium has exhibited, over the past several decades, a remarkable price stability, free of conjunctural fluctuations. Because of its availability and versatility, it will continue to be one of the key metallic elements for future technologies.Key Features of VanadiumIn attempting to single out the key features of the metallic element vanadium, three descriptive characteristics come to mind: availability, versatility and price stability."

Jan 1, 1982

By A. Atrafi, L. Barroilhet

The top size of particles in the flotation of potash ores, which can be as large as 4 mm, exceeds by far the top size in other flotation plants. It is then understandable that while long chain amines are used in the flotation of fine fractions (below 0.8 mm) of potash ores the coarse particle flotation also requires an extender oil. While new and very promising fluidized-bed flotation machines (e.g. HydroFloat) constitute a significant development in the flotation of coarse particles, in the area of extender oils, as reviewed in 2007 by Strathdee, Gotts and McEachern, there have been no new developments to replace the industry standard asphaltene-based carcinogenic extenders. This situation first of all results from the experimental problems that arise when water-soluble minerals like sylvite are to be tested in saturated brine. Both oils and longchain amines are water/brine insoluble. The oil with the amine dissolved in it can however be emulsified and then used as an extender oil. Such oil droplets must wet KCl particles and the emulsion must be stable to avoid handling problems. In this paper we test the use of the phase inversion technique as a method of studying wettability of KCl particles by the oil in saturated brine, and the effect of amine dissolved in this oil on the wettability. The results show that this relatively simple technique can be used to characterize the wettability of fine KCl particles by the tested oil and to determine the effect of added amine on it, and so it can be useful in selecting proper extender oils.

Jan 1, 2016

By Philippe Henry

HYDROMETAL is using suitable technology to reintroduce lost metal units into the industrial cycle, thereby saving resources and energy while keeping the environment cleaner. Hydrometal is treating on average 60000 t per year of complex materials through a unique hydrometallurgical recycling concept. Zn, Cu, Sn, and Pb are the most important in volume, but in the last 15 years, Hydrometal has also developed a few specific recycling treatments for the minor metals including Ge, In, Co, etc. In 2010, Hydrometal commenced the recycling of RE (Rare Earths) from wastes generated by the RE refining industry in Europe and has decided to initiate new recycling projects for the RE recovery from the magnet or glass industries. Two case studies of recycling of materials in our integrated hydrometallurgical facility (Hydrométal) in Belgium are discussed: recycling of cerium from polishing sludges; and recycling of Ni- Co from cement produced in the zinc industry.

Jan 1, 2014

By Jeonghwan Kim

Intelligent Excavation System (IES) has been considered to be one of the desirable solutions to improve the productivity, quality and safety of the current earthwork processes. IES is composed of various hardware and software modules including task planner (work command generator), local and global work environment sensors, GPS and other sensors to acquire the excavator?s status, robotic controller and electronic valves, and the manipulator (excavator). A data communication manager was required to coordinate the signal or data-flow in between these modules considering the operational status of IES such as; excavation start/completion, truck detection, terrain model update, emergency stop, local sensing, GPS/motion sensor data handling, and so on. This paper presents the role and functions of this data communication manager. After every possible operational status of IES operation was identified, a protocol of each communication process in the form of string-type was made. The components of IES are connected with either wired or wireless network. Therefore, they can communicate with the manager using socket (TCP/IP) communication. The data communication manager is also capable of accessing a web-based project management information system, which constantly updates the performance of excavation robot to online database.

Aug 1, 2013

By J. Sadaki, G. Dodbiba, S. Murakami, T. Fujita, S. Matsuo, H. Ono, K. Okaya

Printed circuit boards (PCBs) from discarded personal computer (PC) and household appliances were crushed by mechanical crushing or water explosion to remove mounted parts. More parts were stripped from PCB for PC composed of epoxy resin than from PCB for household appliance composed of phenol resin. In an attempt to raise the copper grade of PCB by removing other components, a carbonization treatment was investigated. The crushed PCB without surface-mounted parts was carbonized under a nitrogen atmosphere at 1073K. After screening, the char was classified by size into oversized pieces, undersized pieces and powder. The copper foil and glass fiber pieces were liberated and collected in undersized fraction. The copper foil was liberated easily from glass fiber by stamping treatment. On the other hand, tantalum capacitors were collected from mounted parts. The tantalum-sintered bodies were separated from molded resins by heat treatment at 723 to 773K in air atmosphere and screening of 0.5mm. Silica was removed and 70% of tantalum grade was obtained after more than 823K heating and separation.

Jan 1, 2011

By M. Jarvis, D. B. Dreisinger, T. Hitchins

Mineral carbonation (MC) has been extensively researched all over the world since it was found as a natural exothermic process to permanently and safely sequester CO2. In order to accelerate the natural process, various methods for carbonation of Mg-/Ca-silicate minerals and other industrial wastes have been studied. It has been found that the MC efficiency will increase with an increase of CO2 pressure, retention time, temperature, mass ratio of Mg or Ca to Si in minerals, specific surface area, and the slurry concentration in a specific range, and with the introduction of an effective catalysts, for example, 1M NaCl and 0.64M NaHCO3 or carbonic anhydrase. However, there still is not a successful industrial application because of high economic cost and slow reaction rate. It is not economic to exploit Mg- and Ca-silicate minerals deposits or tailings to sequester CO2 by MC, due to the cost of grinding and heat pre-treatment and in some cases the whole sequestration process may result in more CO2 emissions than the amount of CO2 sequestered, due to the requirements of energy inputs. The process however, may be profitable as a whole (with carbon credits). It is suggested to combine MC with recovery of valuable metals from ore deposits in order to reduce the cost for MC by cost sharing for mineral recovery.

Jan 1, 2017

By T. Patching

"A GLANCE BACK AT what has happened in the past is often a useful guide to the future, although it should be used mainly to provide a sense of direction rather than a map that must be followed. As a preamble to discussing some of the questions posed by the organizing committee it may be appropriate to briefly review the distribution and careers of the graduates of our Department since the first degree in mining engineering was awarded in 1916. An attempt has been made to keep a record of the locations and careers of the Department's 540 graduates in mining and metallurgical engineering. Almost all of those who graduated before 1930 have now retired, but a very large proportion held positions as senior executives prior to retirement. A major proportion of those who graduated before 1950 are now in what might be considered senior management positions. Those who have 10 to 20 years of experience are generally in work of senior engineering responsibility or in supervisory or junior management ranks, while those who graduated in the last ten years appear to be generally in staff engineering or junior supervisory positions. This classification is admittedly imprecise because it is difficult to determine from a job description whether duties should be considered of an engineering or management nature - a distinction between the two terms is often over-emphasized. Nevertheless, the trend from technical engineering to management responsibilities with seniority and years of experience is clear in the careers that we have been able to follow."

Jan 1, 1972

By V. Nudo, R. del Villar, A. R. Laplante

"Fine iron ore recovery from the tails of Les Mines Quebec Cartier was investigated using Reichert trays and spirals. The effect of feed rate, density and splitter setting on the performance of rougher, cleaner and recleaner stages of a 2DS tray assembly was determined using 2- and 3- factorial experimental designs. The tray concentrate, assaying 27% Fe, was further upgraded by spiral to yield a concentrate assaying 55% Fe. Further laboratory scale testing showed this material to be easily upgraded to 65-66% Fe with high Fe recoveries.This paper presents the metallurgical results of the three tray stages. The model used to predict the performance of a full recovery circuit is then described. Simulation results are presented and their reliability assessed. Finally, an economic evaluation of the proposed scavenging circuit is summarized.INTRODUCTIONThe Mount Wright plant (UWP), located near Fermont, Quebec, processes daily 130,000-150,000 tonnes of iron ore assaying between 27 and 33% Fe, to upgrade it with three stages of 44.5 cm pitch GEC spirals to 66% Fe, while rejecting approximately 80,000 tonnes assaying between 6 and 11% Fe (1-3). Heavy liquid separation (at 3. 3 g/mL) of the plus 37 µm fraction (+400 mesh) of the tails reveals that a significant fraction of the iron is in the sink product, below 150 pm (100 mesh), as shown in Table 1. Also shown is the iron grade of the sink and float fractions. The high grade of the fine sink indicates that hematite ls well liberated below 105 µm (150 mesh), as previous studies have shown (4,5). The iron grade of the floats is very low in the fine size range, but increases with increasing size above 105 pm, because of incomplete liberation. Overall, two thirds of the plus 37 µm iron ls in the sink product, which constitutes less than 10% of the total tail."

Jan 1, 1987

Real time analysis of ore quality between the mine and mill provides major benefits to copper mining and processing operations. Prompt gamma neutron activation analysis (PGNAA) is a proven technique that has been successfully applied for real time conveyed flow multi-elemental measurement. The advantage of PGNAA is that it measures through the full conveyed cross section continuously and provides representative element measurement without the need to constantly sample coarse (primary crushed) conveyed flows. High specification PGNAA analyzers enable accurate measurement over time increments as short as thirty seconds. Elements such as copper can be measured to a precision of 0.02% copper which is sufficient for high confidence in decisions for bulk flow diversion. Increments of eight tonnes are being diverted through a bulk ore sorting application to remove batches of waste from mill feed as well as divert material to different stockpiles based on ore quality. Longer measurement increments of two to five minutes are suitable for blending control of ores to reduce feed quality variability and to control average ore quality within a target range. Feed blends can be adjusted as frequently as required but typically multiple measurement increments are composited to produce a rolling average ore quality. The paper details two case studies where analyzers have been successfully used to measure conveyed flows for blending and bulk diversion applications. The real time measurements of ore composition are also used for ore reconciliation, in metal accounting and providing process operators with advance warning of ore quality changes that may affect grinding performance and cause process upsets. Real time ore quality measurement has proven beneficial in improving copper processing performance through better utilising plant capacity in a leaching operation, optimising ore feed quality, and reducing unnecessary processing of waste. INTRODUCTION Representative real time elemental analysis of conveyed ore quality using fully penetrative technologies has been available to the minerals industry since the 1990s. The Prompt Gamma Neutron Activation Analysis (PGNAA) technique was developed into a conveyed material analyser and soon adopted by the cement and coal industries which recognised the benefits in real time quality management. These commodities were ideally suited to this measurement technique as operations generally involved conveying bulk material prior to processing. Measured quality was used to divert material to different destinations or used to control blending for improved quality consistency. Uptake in the minerals industry, however, has been slow until the last ten years, and particularly until the mid-2010s.

Jan 1, 2019

By Daniel Torres Espinoza, Jose Pinedo

"Ventilation is a vital service in underground mines, required to provide fresh air to the work force and dilute diesel equipment gases (CO, NOx) and diesel particulate matters (DPM). At a Mexican precious metal mine in the state of Chihuahua there is a VOD system implemented using Howden’s control and monitoring system and a state of the art tagging and tracking technology. The JM zone of the mine is ventilated using a push and pull system, using automated regulators on each level to control the air going in and out of the levels. The implementation of advanced control strategies using Howden’s VentSim™CONTROL allows the mine to generate significant savings and increase health and safety of the workers.INTRODUCTIONIn underground mines, ventilation is a requirement in order to maintain the fresh air needed for personnel and equipment. Ventilation regulations dictate the amount of air required underground to carry out day to day operations by limiting the exposure that workers have to toxic gases and other pollutants. Regulations for required airflow in underground operations for diesel pollutants are generally provided on vehicle rated brake horsepower, in Mexico the requirement is 75 cfm/bhp. In underground mines, ventilation services can account to up to 75% of the mine’s energy consumption, and it is very common for fans to operate all the time because of a lack of control infrastructure for the ventilation system. By the implementation of a Ventilation On Demand (VOD) system a mine can reduce this consumption with different control strategies. The main infrastructure required to implement this system consists of remote control of ventilation infrastructure (fans and regulators), a communication network between throughout the mine with the surface and a tracking system for personnel and diesel equipment. Software is required to determine fresh air requirements based on the tracking system data and then send the control commands to the different ventilation infrastructure. In 2015, San Julian Mine acquired Howden’s VentSim™CONTROL (formally SmartEXEC) and the hardware solution to deploy a VOD system at their operation. The VOD system and Fresnillo plc’s San Julian Mine in Chihuahua, Mexico, consists of control of 10 surface exhaust fans, 2 surface intake fans, and 12 underground automated regulators. It also includes the monitoring of 46 flow sensors, 28 CO sensors, 28 NO?? sensors and 42 temperature and humidity sensors, approximately 500 personnel tags, approximately 220 vehicle tracking tags with diesel status (ON or OFF) and approximately 250 tracking zones. This paper discusses the control strategies that have been implemented at San Julian Mine since the system was commissioned and the next steps that will be taken at the mine with the system as they test different level on VOD."

Jan 1, 2019

By Darrell McClarty, Roger Payne, Matt Haggis, Michael Courtin, Deborah Berthelot

"Over forty years of uranium mining in the Elliot Lake region of Ontario (I 956-1996) has resulted in the production of over 300 million pounds of uranium. With the completion of mining activity, Rio Algom Limited and Denison Mines Limited are utilizing progressive environmental technologies and management systems to reduce and manage the environmental risks associated with the 150 million tonnes of potentially acid-generating tailings in nine regional waste management areas. Water covers designed to reduce oxygen entry and thereby significantly inhibit acid generation have been applied at six of the sites with the Quirke site serving as a demonstration site for the Mine Environmental Neutral Drainage program. All five of Rio Algom Limited' s effluent treatment plants are monitored and controlled from a central control station utilizing a Supervisory Control and Data Acquisition (SCADA) system based on ""Fix Dmacs"" technology. Scheduling, auditing and reporting of plant operating and environmental monitoring programs for the entire watershed are controlled utilizing the Regional Environmental Information Management System (REIMS). Proper application of these technologies and management systems facilitates delivery of cost-effective environmental monitoring, care and maintenance programs at these sites and provides tools to demonstrate compliance with all environmental performance criteria.IntroductionCost-effective management of multiple tailings management areas distributed throughout a 35 km watershed requires the application of leading-edge environmental technologies. Long-term monitoring, care and maintenance costs must first be minimized through the application of decommissioning technologies that inhibit acid generation and minimize the release of contaminants from the sites. On-going operating costs must then be controlled through the application of environmental management strategies that optimize the allocation of resources while ensuring compliance with regulatory and Company environmental requirements.Using sites in the Serpent River Watershed as an example, this paper demonstrates the effectiveness of water covers as a decommissioning strategy to inhibit acid generation. In addition, the Telemetered Environmental Operating Control System and Regional Environmental Information Management System are reviewed as examples of the application of environmental technologies to the management of environmental programs."

Jan 1, 1998

By Julian Baldry

"This paper begins by describing the parameters of high-speed underground tracked drifting operations and the mucking cycle, and-discusses their variations. The railbound Haggloader 8HR is then described, as well as the Hagglund shuttle trains, outlining the advantages and disadvantages of the system. A comparison with conventional mucking operations is then given.IntroductionDrift and tunnel rounds are mucked by one of two major methods, either trackless with diesel loaders and trucks or with track loaders and cars. The aim of this paper is to compare the conventional tracked mucking cycle with the Hagglunds system alternatives.For many years, the traditional method of attacking the mucking cycle has been with a rocker shovel loader, a string of cars and a locomotive. The rocker shovel loads the first car and when full it is taken to a side drift, cherry picker or some other transfer point and is exchanged for an empty one. This empty car is then pushed back into the face and the loading continues until all cars are full . Then the whole train is taken out to a dump point where the cars are emptied. Normally the train's capacity is less than the volume of the muckpile, so the cars go back to the face. This loading cycle is repeated until all muck is removed from the heading. The last train out from the heading usually takes the loader and parks it in a side drift before continuing on to the dump where the cars are emptied.This simplified version of the traditional loading cycle excludes the ancillary work elements such as track laying and so on, but does point out that the cars must be transferred when full and that the whole train normally makes at least two round trips from the dump to the face. The prime aim in drifting is to cycle a round whithin a working shift which necessitates that no one part absorbs so much time as to prevent the completion of the cycle.Mucking, drilling and loading and the ancillary work such as rock bolting, vent and service pipe hanging typically each take one-third of the available work time. Drilling or mucking can and often do, because of various factors, take nearly half of the total cycle time. Once any segment of the operation starts to take this portion of the shift, the likelihood of missed rounds becomes increasingly greater."

Jan 1, 1981

By E. A. Collins

I TAKE it that the papers presented tonight on the subject of Reconstruction, as regards both gold and base-metals, are intended primarily to stimulate discussion of this important subject and, in regard to base-metals in particular, cannot in any manner be considered as a policy or plan to be followed as a panacea for all the ills which are bound to beset the industry when peace is declared. A famous cook-book written by a Mrs. Beeton contained a recipe for jugged hare which began with the instruction, "First catch your hare". To date, we have not caught the hare of victory and it may seem to many that any thought, energy, or effort devoted to the problem of reconstruction which will in any way impede the acceleration of the chase after victory will leave us open to the charge of being derelict in our duty as citizens. Much of our present trouble is due, however, to our lack of preparation for war in time of peace, and it follows that it is of equal importance in our national economy to prepare for peace in time of war. Most of us here tonight have vivid and sad memories of the chaos in the metal mining industry following the Great War of 1914-1918. In our own industry, mining, smelting and refining of nickel and copper, it was not a problem of absorbing the men who returned. There were only some three hundred who came back to the Mining and Smelting Division, and these men were all given their former jobs without any apparent difficulty. They were rehabilitated gradually due to the fact: that some of these men did not return for a year after the Armistice was signed. The numbers of men involved in the present conflict are much greater. We have to date in the armed forces upwards of 3,000 men enlisted from our employ.

Jan 1, 1943

By P. Hubert, J. P. Ildefonse, F. Qafssaoui, J. Poirier

Corrosion tests by corrosive alumina-lime slags were carried out on commercial high alumina bricks used in steel ladle linings and model refractories (with different raw materials : bauxite, andalusite, and different microstructures). Using (SEM) scanning electron microscope and (EDS) energy dispersive spectroscopy, microstructures of slag-corroded refractory interfaces were studied in detail. The monomineral and glassy phases, the composition of reaction products and chemical profiles were determined. A thermochemical analysis based on phase equilibrium diagrams has permitted to estimate the proportion and the composition of the high temperature intergranular liquid phase. These data were compared to the experimental microanalysis results. The viscosity of the high temperature liquids were calculated according to Urbain 's model and the relationship between the viscosity and the penetration of liquid phases were discussed. These theorical and experimental results were used to understand the complex phenomena of slag penetration and corrosion of andalusite and bauxite refractories at high temperature and to propose new ways of improvements for the formulation of high alumina refractories.

Jan 1, 2004

By Haibin Wang, Zhiwei Huang, Zhixiang Cui, Wenzhao Cui, Zhi Wang

Fangyuan Two-Step copper smelting process was commercialized in October, 2015 and has been operating for 3 years and 5 months. As the unique continuous copper smelting process with simplified flow in the world, production parameters have been significantly improved after three years. In the first half of 2018, the feed rate was above 200t/h, availability reached 97.5%, operation cost was about 20% lower than the conventional three-step processes showing obvious economic advantages. The Two-Step process in Fangyuan is composed of 1 Submerged Lance Smelting furnace (SLS) and 2 Submerged Lance Converting& Refining furnaces (SLCR). Two SLCRs work alternatively to ensure continuous production. High grade and liquid matte from the SLS is introduced to the SLCR by sealed launder to complete converting and refining. The SLCR is an original and independent innovation of Fangyuan, for which Fangyuan completed lots of development and improvement. This paper will introduce the process and experience. INTRODUCTION China is the largest producer and consumer of refined copper. Most of the processes adopted in China are conventional "Three-Step" copper smelting processes, which are comprised of smelting, converting and refining. There exists some problems in the conventional processes, such as high energy consumption, large heat loss, low altitude emission of SO2, etc. To deal with these problems, Fangyuan developed the new copper smelting process with simplified flow, low cost, clean and high efficiency. The SLCR that combines converting and the refining process was also developed, which shortens the process flow from conventional three steps to two steps. The SLCR is of great significance in promoting the development of the copper industry. Development and industrialization of SLCR At present, copper concentrates are treated in three steps: smelting, converting and refining. Anodes are also produced by continuous converting processes such as the Mitsubishi process and the Double Flash process. Problems like matte transportation by ladle, capacity limitation, and low altitude pollution exist.

Jan 1, 2019

By Yun-Soo Lee, Su-Hyeon Kim, Hyoung-Wook Kim, Joon-Hyeon Cha

A7075 aluminum alloys have high strengths but poor corrosion resistance. In order to improve the corrosion resistance, a clad sheet is suggested, that is the A7075 alloy sheet bonded to A1XXX or A6XXX aluminum alloy sheets which are surface layers with good corrosion resistance. Mechanical properties of the clad sheets are determined by the combination of the component layer sheets, and thermomechanical treatment should be precisely designed when the strengthening methods of the core and the surface alloys are quite different. In the present study, three-layered A6022/A7075/A6022 clad sheets were fabricated by roll bonding process. Simplified processes incorporating a twin roll casting were also suggested in order to reduce the processing cost. Several temper methods composed of rolling, annealing, solution treatment, and aging were suggested in order to optimize the mechanical properties of the sheets. The strengths of the clad sheets were compared with the bare A7075 and bare A6022 sheets.

Jan 1, 2015

Access to accurate real-time information is critical to maintaining efficiency and competitiveness in any modern minerals processing facility. At MMG LXML Sepon Copper Operation in Lao P.D.R., controlling the copper grade of the feed to the leaching circuit is paramount for maximising productivity and copper recovery. Since 2008, real-time analysis data has been available to process engineers from the Geoscan on-belt analyser installed on the Copper Mill feed conveyor. Access to accurate real-time results from the Geoscan has allowed the process engineers to strictly control blending based on copper grade to overcome variability in the plant feed, where conventional sampling and laboratory analysis is difficult, error prone and time consuming. In addition to enjoying these benefits since the Geoscan’s installation, in recent times the process engineers have expanded the use of the Geoscan by observing elemental results other than copper grade to control different aspects of the operation, focussing on the reduction of Gangue Acid Consumption. This paper discusses the process of expanding the Geoscan use at the operation, including an explanation of the calibration process. Additionally, a brief description of the Geoscan and its use at MMG LXML Sepon Copper Operation is provided, as well as a summary of recent calibration and analysis results. A discussion of future works concludes the paper.

Jan 1, 2016