Search Documents

By J. Lu, D. B. Dreisinger, G. Houlachi

"Zinc metal is primarily produced by electrowinning from sulfate solution. Zinc electrowinning is very sensitive to impurities such as Co and Ni. These impurities have to be removed to produce high-quality zinc and maintain a high zinc current efficiency. Zinc dusts are used to remove these impurities by cementation. However cobalt cementation is extremely slow and it is typically activated by the addition of Cu and Sb. Even with the use of Cu-Sb activation, cobalt is still difficult to remove. The zinc dust used for cobalt cementation is negligible compared to that consumed for hydrogen evolution. In some plants up to 6-7% of electrolytic zinc is used for cementation. This is a great waste of energy. Cu-Sb activation is not well understood. The objective of this study was to further understand the Cu-Sb activation and then find a way to reduce hydrogen evolution and promote cobalt cementation. The investigation reveals how hydrogen evolution (or zinc dissolution) and cobalt cementation and re-dissolution change with temperature, zinc dust dosage, the concentrations of copper and antimony and time. In the Cu-Sb activation, copper is deposited on a zinc particle to produce a porous shell. The zinc particle as an anode dissolves while the shell as a cathode provides a place where cobalt cementation and hydrogen evolution occur and they are catalyzed by antimony. A certain level of antimony (around 0.1 mg/L) is a key to maintain the catalytic effect of the shell. At a higher antimony concentration, cobalt cementation is accelerated slightly while hydrogen evolution is increased greatly. When a zinc particle dissolves to a certain degree, cobalt loses its cathodic protection and starts to re-dissolve. The change in cobalt concentration is determined by the rates of cobalt cementation and re-dissolution. The operation conditions can be optimized to maximize the cobalt removal and minimize the zinc dust dosage.INTRODUCTIONMost of the world’s zinc metal is produced by electrowinning from sulfate media. Many impurities such as iron, copper, cobalt and nickel are co-extracted into solution with zinc. Iron, mercury, indium, lead and tin are removed by co-precipitation as hydroxides. Copper, nickel, cobalt, aluminum, arsenic and germanium are partially co-precipitated with iron while cadmium, magnesium and chloride remain in solution. Cobalt, copper, cadmium, nickel and etc. are subsequently removed by cementation with zinc dust to achieve an acceptable current efficiency and high purity metal product for the economical production of zinc. Zinc provides a strong thermodynamic driving force for the cobalt cementation:"

Jan 1, 2016

By Brian O'Hearn, Doug Hanson

"The most commonly used tendon supports in the Sudbury area include rock bolts, rebars, friction anchors and cable bolts. Due to the fact that these tendons are physically different and employ different anchoring systems they offer varying degrees of stiffness, yield ability, load capacity, anchor dependability and energy absorption. These differences coupled with variable rock mass and changing stress conditions have made it challenging to engineer the design of an effective support system. By tapping into the knowledge and experience gained by ground control practitioners, an empirically based rating system has been assembled that offers a guide to designers of support systems when choosing the most effective tendon support over a range of rock mass and stress conditions.A methodology referred to as support planning can be used to design support systems whose rehabilitation costs will be minimized. The use of multiple tendon types in anyone support layout is advocated, particularly when the stress state of the rock mass to be supported is expected to undergo a change."

Jan 1, 1995

By A. Khan, C. Ciriello, W. Oliveira

"The purpose of this paper is to demonstrate the value of Operational Readiness (OR) in the successful delivery of capital projects. OR can be captured using several technical and practical definitions:• To ensure that the capital project being delivered is capable of an effective start up, ramp-up as planned and a sustainable productive operation.• To function as intended when started, with the appropriate people able to run it.• To increase the value in delivering the product/service through established systems, processes and procedures, while simultaneously minimize risk to both the project and the business.Historically, mining and metallurgical capital projects concentrate efforts on cost and scheduling during the implementation and design phases. The completion and subsequent handover of the operational unit is the main objective.When reviewing the mining and metallurgical industry’s capital projects, it seems many poor results and errors in terms of project design and ramp-up are self-inflicted, with the project neglecting to account for key aspects of the future operational plant. Interestingly, if the problems for the future plant occur during project implementation, they can be prevented during the project phase. It is required to connect the operational knowledge with the project in order to ensure an effective start up and operation.The benefits of OR will be shown to be applicable not only to mining capital projects but also to sustaining and business transformation projects. The paper also includes industrial examples showing both proper and improper use of OR techniques.The paper will cover 3 main areas of Operational Readiness: the OR model, OR related risk elements (i.e., risks associated specifically with the improper execution of OR) and conclude with OR specific case studies."

Jan 1, 2016

"Classification is an important aspect of mineral processing plants and if not operated efficiently can compromise both the throughput and recovery of the circuit. This paper discusses the benefits that can be obtained by operating the classification section efficiently. Since classification in most of the mineral processing plants is carried out using either hydrocyclones or screens the case studies involving the two classifiers were used in the discussion. Studies where optimising the classification circuit lead to improvements in the performance of the overall plant were included to show the benefits of paying attention to this area that is usually neglected. The data from the mill-float mill float, SABC, and Single Stage SAG mill circuit case studies have shown that the circuit throughput can be increased throughputs without compromising recoveries by optimising the classification circuit. On plants where the ore can be liberated at coarser sizes the experimental results have shown that replacing hydrocyclones with high frequency screens can lead to improved plant throughput with no detrimental effect on recovery. The discussion has included information on design and operational considerations for plants that have or intend to use hydrocyclones or screens that could make the classification circuit more efficient.INTRODUCTIONComminution is the process in which particles are reduced in size mainly by crushing and grinding. In most mineral processing circuits comminution is carried out to liberate the valuable minerals prior to subjecting the ore to a recovery process were values are concentrated or extracted (Mainza, Evertsson, Benzer, Tavares, Powell, Rule, Plint, …, 2013). Comminution is an energy intensive process and is usually achieved in stages. It is common to have a classifier after each comminution stage. The process is carried out in stages to minimize energy usage and to improve the efficiency of the process in meeting product specifications. Although comminution circuits have been advancing classification has remained a key component of the comminution circuit design (Mainza et al., 2013). Mainza et al. (2013) summarised the role of classification in mineral processing circuit as: to allow material in the equipment that can promote high operational efficiency, to improve material handling in the circuit, to minimize overgrinding of material to reduce energy consumption, and to provide the best quality product to enter the next stage of processing. Classification stages are employed in comminution circuits to ensure that high throughputs are processed without compromising the product quality or to produce a fine product at relatively low energy. If neglected classification can have detrimental effects on plant performance."

Jan 1, 2016

By Yuki Tsunazawa, Sho Fukui, Chiharu Tokoro

"A milling process is one of the important unit processes in mineral processing. In the milling process, the control of particle size distribution is necessary for the later physical separation process. Since the milling process is strongly affected by the equipment designs, operation conditions and raw materials, the control for particle size distribution of milling products is mainly based on empirical rules. Recently, the discrete element method (DEM) has been widely used as an effective tool to investigate the behavior of grinding media. Although the behavior of grinding media can be accurately simulated, it is not well-established the way to predict particle size distribution after milling by the DEM simulation.The objective of this study was to develop a new method to predict particle size distribution in ball milling using the DEM simulation. To predict particle size reduction, a correlation between experiments and the simulation was investigated in various operation conditions, that is, wide range of the rotation speed and the filling ratio of grinding media. In experiments, after lime stone was ground, the average and variance of particle size distribution were evaluated using some kinds of distribution equations. In the DEM simulation, direct simulation of particle disintegration in milling process is generally very difficult because of huge computational load. Therefore, collision energy between grinding media balls orgrinding media ball and wall was used as a factor of particle disintegration.As a result, a good correlation between experiments and simulation was obtained. In addition, the particle size distribution in ball milling could be predicted using this correlation. Therefore, these results indicated that the use of the correlation between experiments and the DEM simulation was an effective approach of predicting the particle size distribution in milling process."

Jan 1, 2016

By D. M. Xue, T. B. Li

"With the increase of human engineering activities, global climate change and active plate tectonics movement, the giant landslide frequently occurred in southwest China, which caused huge property and human losses. Besides, the potential landslides pose severely threaten to the construction and operation of airports, railways, highways and power stations etc. In order to provide accurate guidance for the landslide investigation, stability analysis and mitigation, the giant landslide is redefined according to landslide volume, depth of slip surface, complexity of landslide mechanisms, and degree of landslide mitigation difficulty, and classified with the typological classification approach based on the twofold attributes of landslide behavior including formation mechanisms and reactivation features. Finally, the threefold particularity of the giant landslide is also summarized, which enables a more effective landslide mitigation design.INTRODUCTIONWith the increase of anthropogenic activities, global climate change and active plate tectonics movement such as continual uplifting of Qinghai-Tibet plateau and strong earthquakes, the occurrence of giant landslides was in ascending trend in southwest China (Huang, 2009), which caused serious destruction, and greatly endangers such engineering construction from safety, time and economic aspects as airports, railways, highways, power stations, etc. Giant landslides have huge scale, complex formation/reactivation mechanisms and mechanical behavior. They may not be identified during the hazard investigation, but may be firstly initiated or reactivated due to the following engineering activities, heavy rainfall or strong earthquakes. Consequently, the landslide mitigation is inevitable and costly. However, it is difficult to control the deformation of giant landslide with lack of a correct understanding of genetic mechanisms (Marui, 2012; Zhang, 2000) and the excessive large sliding forces of the slide blocks calculated by the conventional limit equilibrium method. For instance, the failure of anchored pile wall for the No.102 giant ancient landslide (Zhu et al., 2012) and stabilization measures for the Sidi Rached viaduct landslide(Guemache et al., 2011); four rows of piles had not prevented the occurrence of the No.12 landslide in a high fill slope in the Panzhihua airport (Li et al., 2012)."

Jan 1, 2015

By A. P. E. Dirige

The stability design of cemented backfills is normally conducted using conventional approaches. Analytical or numerical models, backed by trial-and-error methods, are the primary means used to describe or predict the support performance of backfills during mining. The stability of paste backfill free-standing faces is a major concern due to potential consequences to production, ore dilution and safety. Available analytical or mathematical models are developed based on assumptions of the failure modes that may occur when vertical fill faces are exposed during adjacent mining. Numerical modeling serves to provide an understanding of backfill strength and deformation behaviour. Such approaches offer inherent limitations and generally result in conservative designs. In this paper, centrifuge physical modeling was conducted not only for performance evaluation studies, including stability analysis, but to develop an understanding of the strength and deformation behaviour of paste backfill exposed faces when the adjacent ore zone is removed. The failure mode and mechanics of failure observed in the centrifuge model of a given prototype situation are discussed in detail. Centrifuge model results were compared to numerical modeling and it was concluded that a sliding block failure mechanism that resembles a circular slip appears to be the predominant failure mode.

Aug 1, 2013

By H. Weissenbaeck, B. Nowak, M. Oesterreicher, R. Stastny

The producers of certain metals like nickel and cobalt increasingly face a shortage of easy-to-mine and easy-to-process ore bodies. Their focus is shifting towards alternative raw materials which in turn demand new, different extraction techniques. One potential route for processing a ferrous ore with a non-ferrous target metal is atmospheric leaching with hydrochloric acid followed by purification of the pregnant leach solution (PLS). For the separation of iron from the PLS, and, in turn, the extraction of the non-ferrous compounds, the following flow sheet is proposed. Pre-concentration of the PLS, oxidation of ferrous (if present) to ferric chloride, hydrolysis of ferric chloride leading to the precipitation of hematite and the evaporation of hydrochloric acid, followed by crystallization of non-hydrolysable metal chlorides by means of sparging hydrogen chloride into the solution. Hydrogen chloride required in the latter step is produced internally by super-azeotropic distillation of regenerated hydrochloric acid. The liquid filtrate from the crystallization step is recycled to hydrolysis. Depending on the specific composition of the PLS, the hematite produced contains only traces of other impurities, whereas the crystallized mix of non-hydrolysable metal chlorides – containing also the target metal in enriched form – contains ferric chloride only in an amount referring to the filter cake moisture. These crystals can then undergo further hydrometallurgical separation and extraction processes. As an example, this flow sheet is proposed for treating nickel laterite ores. Experiments related to the demonstration of crucial assumptions in the flow sheet are presented. Based on those experiments a mass and energy balance of the flow sheet was calculated and is presented here together with a table of the major consumables in order to provide a basis for an operating cost estimate and other process economics.

Jan 1, 2016

By Louise Corriveau

A Targeted Geoscience Initiative transect in the eastern Grenville Province reveals an extensive VHMS-style cupriferous hydrothermal system among rhyolitic pyroclastic rocks of the Wakeham Group at La Romaine, Québec. The volcanic rocks outcrop sporadically along a < 10 km-wide by about 100 km-long belt correlated with the south-eastern extension of the Wakeham Group. This belt occurs among voluminous, magnetite-bearing, granitic gneiss. At Lake Musquaro, 1.51 Ga metarhyolitic to dacitic lapillistones and flows, locally with aluminous nodules and veins, are intruded by 1.49 Ga feldspar porphyries. This volcanic package was deposited on typical Wakeham Group arenite (< 1.52 Ga) interbedded with nodular, muscovite- and fibrolite-bearing gneiss, and minor marble hosting finely layered garnetiferous hornblendite, garnetite and magnetite-bearing coticule. The latter are interpreted as meta-exhalite and with the associated albitite (sodic alteration), aluminous veins (hydrothermal leaching) and magnetite-rich granitoids, they are key elements in the search for concealed mineral deposits in this area. At La Romaine, to the south, 1.5 Ga lapillistones outcrop structurally above metasediments and below a composite amphibolite unit of uncertain origin (lava or sills) with magnetite-rich (BIF?) units. An extensive zone of aluminous gneiss, with lapilli textures, provide evidences for severe hydrothermal leaching of the volcanic rocks prior to metamorphism. An adjacent siliceous vein-textured unit likely represent a zone of intense silicification (74 wt.% SiO2), while aluminous, hematite to magnetite-bearing veins in adjacent felsic gneiss (tuff?) preserve evidences for the sequence of alteration events. Despite granulite-facies metamorphism, the main characteristics of the amphibolite unit persist along the entire belt. This competent unit likely served as a cap rock; the garnetite, diopsidite and hornblendite it hosts provide effective guides to the sites of fluid discharge and mineralization. A number of Cu showings, modest in size, were discovered in this unit. Their systematic occurrence, in a structural-stratigraphic sense, indicates that this setting is attractive for mineral exploration despite high-grade metamorphism and deformation. Late-stage veins laden with fluorite crosscut these alteration zones, and are themselves metamorphosed, indicating that hydrothermal activity was polyphased. SHRIMP U-Pb ages obtained on detrital zircons (1 arenite) and on igneous zircons (5 volcanic rocks, 1 porphyry and 6 granitoids), pervasive arc-type geochemical signatures and presence of in situ rafts of barium-rich garnetite in the granitoids indicate that sedimentation and volcanism occurred between 1.52 and 1.49 Ga coevally with hydrothermal activity and emplacement of a sub-volcanic 1.5 Ga granitic batholith with early, 1.53 Ga tonalite intrusion. Such a geological context can sustain large-scale hydrothermal cells and development of VHMS, Cu-Fe oxides or SEDEX deposits.

May 1, 2003

By Takao Oishi, Go Ohara, Toru Kitazaki, Masahiro Tanaka

"The High Pressure Acid Leach (HPAL) plant for nickel-cobalt mixed sulphide production at Coral Bay Nickel Corporation (CBNC) in the Philippines has been in operation since 2005 with a capacity of 10,000 t/year of nickel. Subsequent to the commissioning of the second plant in 2008, the production capacity increased to 22,000 t/year of nickel (Llerin et al., 2011). CBNC’s annual nickel production reached more than 24,000 tons of nickel in 2014. The concepts to achieve this capacity are the high availability and the reciprocally flexible operation of both plants. The availability depends on some factors, such as the control of impurities in the process and the equipment condition, to mention a few. In the HPAL process, it is not only the autoclave operating conditions that affect nickel extraction but also the impurities in the ore greatly influence it. The major element in the ore is iron and most of this iron is precipitated as Fe2O3, while the rest remains as Fe2+ or Fe3+ sulphate in solution. These ions in solution reduce the availability, so it is important to control the formation of iron ions by controlling the impurities in feed ore as well as the HPAL conditions. This paper presents the general HPAL process and the behaviour of impurities, focusing on iron behaviour in the HPAL process.INTRODUCTIONCoral Bay Nickel Corporation ProfileCoral Bay Nickel Corporation (CBNC) was founded on April 2002, as a joint venture of four companies; namely, Mitsui Corporation (18%), Sojitz Corporation (18%), Nickel Asia Corporation (10%) and Sumitomo Metal Mining Corporation (SMM) with a controlling stake of 54%. Aside from its capital share, Nickel Asia Corporation also supplies the ore and limestone for the High Pressure Acid Leach (HPAL) plant located in Rio Tuba, Philippines, as shown in Figure 1 (Tsuchida, 2008). The objective of the CBNC project is to produce 22,000 t/year (original design) of nickel and 1,500 t/year of cobalt, as sulphide, by the treatment of nickel laterite ore which is a low grade nickel oxide ore in the Philippines (Mines and Geosciences Bureau, 2014). The sulphide product has been exported as a raw material to the SMM Nickel Refinery in Japan for 30 years. The product of this plant, a mixed (Ni/Co) sulphide, is shipped to the SMM’s Nickel Refinery in Niihama, Japan. SMM Corporation provides the technology and management personnel to the plant. SMM Corporation also supplies the sulphuric acid, which is the main reagent for the HPAL process."

Jan 1, 2016

By Robert P. Dufresne

Electrolytic cells are used in electrowinning (EW) and electrorefining (ER) of non-ferrous metals such as zinc and copper, and are a critical part of the purification process. The cell is a large basin and has an electrolyte or aqueous solution, an anode and a cathode, an insulator, and incoming high amperage. Cells are exposed to unfavourable internal and external factors that have a direct impact on their lifespan. Their deterioration can be caused by incorrect polarity, insufficient magnitude, their construction, tension stress, thermal shock, corrosion and other, and their maintenance and replacement can be time-consuming, costly, difficult and environmentally unsafe. Occupational health hazards and dangers posed by the maintenance and removal of the cell should also be taken into consideration. Modifying the design and fabrication method of the cell, using chemical-resistant reinforcement, and increasing tensile and mechanical strength will defer maintenance for a very long time. This can be achieved by a double hull system that comprises full-length composite reinforcement, polymer concrete reinforced with fiberglass pultruded rods and rebars, fiberglass structural layers, and special resin matrices. This will provide protection against thermal shocks, corrosion, leakage, cracks. The design of this cell incorporates a lifting system that will afford quick and easy install without having to move a great number of cells in close proximity, since it is strong enough to stand on its own and not have to be bonded to adjacent cells. As well, the cell can be anchored with ease as it remains stable. This is especially important because space is limited to lift and manoeuver between the cell and the double-girder overhead travelling cranes. The lifting system can also prevent electrocution and loss in product quality, while increasing efficiency and safety in the workplace. Considerable savings in terms of production downtime are also part of the equation. INTRODUCTION Maintenance and replacement of electrolytic cells in electrowinning and electrorefining are operations that pose many challenges, health and safety concerns, and give rise to substantial operational costs. These problems have existed since time immemorial. Electrolytic cells are made of conventional concrete or polymer concrete, and because of the very nature of their composition and their exposure to severe and environmental conditions, their lifespan is short. Although polymer concrete is composed of high-quality materials, and has good thermal stability and resistance to chemicals, nonetheless, maintenance is frequently required in order to maintain the integrity of the cell and to ensure the quality of refined metals. Repairing concrete is a non-permanent solution as cracks will reappear, and every repair weakens the integrity of the cell a bit more, until it reaches a knock- down point and the structure is compromised. The cell needs to be replaced, otherwise the cell will collapse.

Jan 1, 2019

By J. Bouchard, R. del Villar, A. Vazirizadeh

"Industrial flotation is a continuous and often multistage process, where particles of a given mineral species (usually the targeted one), present in different sizes, encounter a large amount of gas bubbles (normally air) to produce mineral–bubble aggregates, which are removed from the flotation device (cell or column) as a valuable product (concentrate). The bubble content inside the cell is characterized by the prevailing hydrodynamic conditions (known as gas dispersion variables), which in turn are known to influence the flotation performance. Although most researchers and practitioners agree that the relationship between the hydrodynamic variables and flotation performance exists, the lack of an adequate method foronline measuring the average bubble diameter has prevented such studies.The aim of this study is to apply appropriate hydrodynamic variables for flotation kinetic modeling (as a key feature of flotation performance) for a given introduced particle size distribution (PSD). In this regard, experiments were conducted in a laboratory flotation column (5.6 cm internal diameter for a total height of 650 cm), and mixtures of quartz (hydrophilic gangue) and talc (naturally hydrophobic mineral), classified in four different size fractions. The correlation between the flotation rate constant and given hydrodynamic variables were analyzed. Results suggest that the relative importance of hydrodynamic variables for flotation rate modeling depends on the PSD. Finally the suggested hydrodynamic variables for each of the various particle size-classes considered were used to produce single variable models for the flotation rate constant. INTRODUCTIONIndependently of the prevailing flotation conditions, the mechanisms for bubble-particle aggregation and the residence time of the phases inside the device must also be considered. In this regard, one of the most used approaches to represent the overall flotation process is as a pseudo-chemical reaction between a particle and a bubble, whose rate (at a given time) is proportional to the amount of remaining floatable species. The proportionating constant is called the kinetic constant or the flotation rate constant."

Jan 1, 2016

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama, Ryuji Oinuma

"Recently, the arsenic grade in copper ores has been increasing year by year. Arsenic bearing minerals (enargite (Cu3AsS4) and tennantite (Cu12As4S13)) coexist with typical copper minerals such as chalcopyrite (CuFeS2). The removal of arsenic from copper ores that contain relatively high arsenic content is essential due to its adverse impact on the environment and the resulting economic consequences. In this study, arsenic removal and dissolution behaviour of Cu and As from enargite (Cu3AsS4) were investigated using ferric sulphate (Fe2(SO4)3) solutions containing sodium chloride under high pressure oxidation conditions. The effects of numerous parameters including the concentration of Fe2(SO4)3 and NaCl, temperature, total pressure, leaching time and particle size were studied while other variables such as pulp density and stirring speed were fixed at 100 g/L and 750 rpm. The results showed that more than 60% of the copper was dissolved in a 0.1 M ferric sulphate solution under the high pressure oxidative conditions, whereas the leaching rate of arsenic was less than 20%. SEM observation revealed that elemental sulphur was deposited on the surface of enargite forming a passivation layer and the residue was agglomerated. Those phenomena may cause a decrease in the copper leaching rate. It was found that more than 80% of copper was dissolved in the ferric sulphate solution in the presence of 0.34 M sodium chloride under the conditions optimized, whereas the dissolution of arsenic in the mixture did not exceed 2%. XRD analysis of the solid residues from the leaching experiments used ferric sulphate and mixtures of ferric sulphate and sodium chloride showed arsenic to be present as scorodite (FeAsO4).INTRODUCTION In recent years, there has been an increase of the arsenic (As) content of copper ores due to the gradual depletion of high grade copper ores. In some copper deposits, arsenic occurs in the form of minerals such as enargite and tennantite. The removal of arsenic in ores containing copper is critical to the production of pure copper and the management of the environmental challenges caused by the smelting process. Due to the environmental risk caused by arsenic emission and the deteriorated quality of the copper product, smelting of enargite concentrates is not an effective method for the extraction of copper (Padilla et al., 2010; Safarzadeh et al., 2014; Long et al., 2012). Therefore, a number of studies have been carried out to develop arsenic removal technologies from copper ores using various methods such as hydrometallurgy (Curreli et al., 2009; Tongamp et al. 2010), pyrometallurgy (Dalewski., 1999; Padilla. et al, 2012) and bio-oxidation (Ehrlich, 1964; Sasaki et al., 2010). Several hydrometallurgical leaching processes like sulphuric acid, alkaline sodium sulphide and sodium sulphate and ferric sulphate leaching have been developed to treat enargite ores and concentrates. The alkaline sodium sulphide leaching process has been developed for the removal of arsenic from enargite (Anderson, & Twidwell, 2008; Parada et al., 2014). The mechanism of the dissolution of arsenic from enargite in sodium sulphite solution is"

Jan 1, 2016

By A. Zrimsek, G. Vingas, R. Wolke

IN 1952, prompted by the great demand of the Canadian drilling and foundry industries for sodium bentonite, the Geological Department of Magnet Cove Barium Corporation, Limited began an extensive search for bentonite deposits throughout western Canada. Their efforts were rewarded in 1958, when substantial deposits of high quality material were found approximately 100 miles southeast of Edmonton, Alberta. The bentonite material, a part of the Edmonton formation in the Upper Cretaceous, is located approximately nine miles south of the town of Rosalind. The land where the bentonite lies has in places .been eroded by stream and glacial action to form a wide gully, convenient for strip mining methods (see Figure 1). The bentonite bed is almost flat-lying, dipping to the southwest at approximately 12 feet per mile. The main bed is 8 to. 10 feet thick and is covered with 15 to 25 feet of overburden. Before stripping, the area is drilled and sampled to evaluate the quantity and quality of the bentonite.

Jan 1, 1962

By Randolph A. Pax

"The internal operation of a tumbling mill is a very hostile environment and precludes the sustainable operation of internal sensors to measure the mechanisms of charge motion and breakage events. Instead indirect methodologies are required to expand the current understanding developed within a framework of perfect mixing of the mill contents. A number of measurement approaches have been successfully used to explore the operation of SAG mills including strain instrumented lifter bolts, mill shell strain measurement and thermal (energy balance) of operating mills.Early acoustics measurement was developed by Hardinge using a 'microphone' located close to the expected toe location. This signal was an indicator of the mill fill. Improvements were implemented with the use of two microphones straddling the toe location to try to increase the sensitivity of the measurement and reduce ambiguities. Further improvements included a filtered signal indicative of steel interactions. Unfortunately, the mechanisms of signal generation and the complexity of the processes do not provide a consistent signal.In recent years, advanced acoustic measurement using arrays of microphones utilising signal processing techniques have been implemented as SmartNoise and validated on over 30 mills. This paper will discuss the results obtained with signals such as water holdup, mill shell steel hits and two each of the toe and shoulder angles. An estimate of the internal mill component wear rates is also accessible.Advanced acoustic measurements with wide bandwidths when combined with physics models and process understanding has achieved a step change in the understanding of the dynamic internal operation of a tumbling mills on time scales of 80 ms. These techniques have been used extensively on SAG mills, but have also been applied to FAG and ball mills. Acoustic measurement is used for the rapid diagnosis of mill conditions and holistic control for optimisation and stability."

Jan 1, 2016

"Sink-float analysis is often used to obtain yield-ash and density partition curves in the coal industry. These provide a valuable tool for evaluating the performance of a separation process. However, for dense minerals, obtaining complete grade-recovery and density partition curves is more difficult due to the lack of heavy liquids available with the required densities. This paper examines a potential solution to this problem which is to perform batch fractionation of mineral samples in a laboratory-scale REFLUX™ Classifier using high viscosity fluidising liquids. The REFLUX™ Classifier is a gravity separation unit consisting of a system of parallel inclined channels positioned above a vertical fluidised bed. Operated in semi-batch mode, a charge of particles is fluidised from below and particles up to a certain density are elutriated from the top of the system. The fluidisation rate is then increased incrementally to fractionate the sample at progressively increasing densities. Previous work by Hunter et al. (2014) and Iveson et al. (2015) has shown that this method provides excellent agreement with yield-ash and partition curves for coal, especially when glycerol solutions are used as the fluidising liquid. This approach has now been extended to obtain the grade-recovery and density partition curves of high density mineral samples. This method has the potential to provide the minerals industry with an effective tool to evaluate the performance of unit operations separating at cut points higher than the available heavy liquids.INTRODUCTIONMeasuring efficiency and effectiveness is of key importance in the continuous improvement of mineral processing plants. For density based separation, one way the performance of a process can be evaluated is the measurement of density-based partition curves. Currently, this is done in the coal industry using the sink-float method, where heavy liquids are used to fractionate particles into discrete density intervals. However, with high density minerals such as iron ore, liquids of sufficient density are rare, and in most cases also pose serious health and safety concerns to laboratory operators. Most commercial laboratories do not perform sink-float separations above a density of about 4400 kg/m3, the maximum density of Clerici solution without operating at excessive temperatures (Koroznikova, Klutke, McKnight & Hall, 2007; Rosenblum, 1974)."

Jan 1, 2016

By Jan Rosenkranz, Anders Sand, Lisa Malm, Nils-Johan Bolin

Within flotation technology the general trend is towards very large cells. Scale-up is usually done by postulating geometrical similarity, which implies keeping the aspect ratio constant when increasing cell volume. Consequently, the design of flotation circuits typically involves several cells of identical geometry within a bank. Using a few standard sizes in a flotation plant simplifies design, manufacturing and maintenance of the cells, but does not necessarily guarantee optimal performance and selectivity of the flotation process. Geometry parameters for a given cell volume that influence flotation cell performance include cell height, which causes changes in the hydrostatic pressure and suspension hydrodynamics, and also influences the travel distance of particle-bubble agglomerates as well as the homogeneity of the mixing. Also the thickness of the froth layer depends on the aspect ratio of the cell. The objective of this work is to gain a better understanding of material distribution and properties within a flotation cell and, based on this information, elucidate how alterations of the cell geometry can influence separation efficiency. For this purpose systematic measurements and analyses of the spatial distribution of the different phases within a 160 m3 flotation cell have been carried out with a particular focus on an industrial, low-grade copper ore beneficiation process. The concepts for sampling at different vertical and lateral positions of the flotation cell are introduced. The results from the experimental work give an understanding of internal material distribution within flotation cells. Based on the measured phase distribution and concentrations as well as particle properties at various positions within the cell, the implications for an optimized scaling and design of individual flotation cells within a flotation circuit are discussed.

Jan 1, 2016

By Laurence D. Burke

The electrocatalytic behaviour of gold in aqueous media is surprisingly complex and a novel view of gold electrode surfaces is proposed to explain the observed electrochemical responses. The metal surface is considered as a chemically (or redox) modified electrode, with equilibrated, low energy, surface gold atoms functioning as a relatively inert support and low coverage, high energy, protruding gold atoms (or minute clusters of same) functioning as electrocatalytic redox mediators. The protruding atoms are viewed as surface active sites and the complex electrocatalytic behaviour is attributed to the basic instability of the mediators, the diversity (and poor control) of same, and the acid/base (or hydrolysis) behaviour of the oxidized states of the mediators. It is assumed that major advances in the application of gold in the heterogeneous catalysis of gas phase reactions will be accompanied by similar advances in the use of gold in the electrocatalysis area; however, this will require considerable work of both a practical and theoretical nature.

Oct 1, 2003

By Pierre Montrueil, Marcel St-Amant

Within the next few years, underground mobile equipment will be partially automated. Mining methods will integrate more and more automation. Such an evolution will be possible only if adequate underground communication systems are developed. This is expected due to the available competence in Canadian telecommunication, to the economic pressure on the Canadian mining industries for international competitiveness and to the social changes where a better working environment (i.e. less accidents) becomes a major concern. CCARM propose the concept of a Production Area Network for Automated Mobile Units called PANAMU as an intermediate size communication system. It can be implemented using mature present-day technology and it can be integrated in some mine wide communication systems. It can evolve so as to incorporate new technologies because of its modular concepts. In this paper, the communication requirements are estimated, the amtmptions are defined, the concepts of the PANAMU are presented and an over- view of its implementation is described. CCARM presents this article to the mining industry as a document for discussion.

Jan 1, 1994

By J. A. Rogers

"The Arthur W. White Mine (formerly Dickenson Mine) is a structurally controlled, hydrothermal gold deposit. A gold producer since 1948, it has, to December 31, 1990, processed 6.9 million (m) tons (T) of ore grading 0.45 ounces per ton gold (oz/T Au). As of December 31, 1991, Proven and Probable Ore Reserves were 3.2 m. T. at 0.32 oz/T Au. The mine is located just east ofPlacer Dome Inc. &apos;s Campbell Mine, within the Cochenour-Gull.rock Lake deformation zone. It is situated on the hanging-wall side of a southeast-plunging anticline in a sequence of metamorphosed Archean volcanic, sedimentary and plutonic rocks of the Red Lake greenstone belt. Ore-bearing structures, found mainly within basaltic rocks, are brittle within greenschist-facies rocks to the northwest, but become more ductile toward the southeast, in amphibolite-facies rocks. Within and proximal to these structures, carbonate and arsenopyrite alteration decreases, whereas biotite, actinolite, pyrite and pyrrh otite all increase to the southeast.Ore and shear structures occur symmetrically about the northwest-trending, steeply southwest-dipping, flattening foliation . The three most common ore trends are on average: (A) northwest trending with a 55 degree to 85 degree dip to the southwest; (B) north-trending with a 40 degree to 50 degree dip to the west; and (C) due east-west-trending with a vertical dip. In general, the dominant direction of economic gold concentrations are explained and thus predicted by considering deformation style (brittle or ductile), rock anisotropies such as bedding and lithological contacts, and direction/magnitude of relative block movement. Direction ""A"" can be found adjacent to both right- and left-handed faults. Direction ""B "" occurs with dominantly right-handed systems and direction ""C"" is found with predominantly left-handed movement. Major faults active prior to, during, and after ore formation can have offsets in the order of 2500 feet. Movements along these faults were transpressive while their conjugate breaks were dilatant, thus creating zones for alteration and ore solution emplacement. A series of faults , each with offsets up to 30 feet were established under lower temperature brittle conditions during late- to post-ore formation. In more complex zones, formed during more ductile deformation, these faults controlled the localized geometry and, thereby, the depletion and enrichment of ore shoots, causing a high nugget effect.Although an important aspect of production planning and monitoring, grade control is also very important within a complex ore zone so that the nuggets are not missed. Detailed observation of structure at the hand-sample scale and detailed mapping at the stope scale give valuable clues to interpreting the structures on a mine-wide scale. Determining the relative movement along fault structures is very important so that using an action-reaction- type logic, potential dilatant areas can be predicted and targeted for development and diamond drilling."

Jan 1, 1992