Search Documents

By Kevin C. Milne

"The solution of problems associated with development of a sour gas reserve will be of increasing importance in tl1e next few years if gas export is approved •by the National Energy Board. The purpose of this paper is to review briefly the history of the Carstairs gas field, and tCI describe in a general manner the reservoir, and the producing and processing facilities.HISTORYThe Carstairs gas field was discovered in April 1958 when the discovery well, Home Carstairs 10-17, was successfully completed as a gas well in the Elkton member of the Turner Valley formation. Geo-graphic location of the field is shown in Figure No. 1. Note that the field is about five miles west of the town of Carstairs, Alberta, which in turn is about 40 miles north of Calgary. Drilling subsequent to the discovery well resulted in three addition-al producing wells and one dry hole during I.958; two producing wells during 1959; and one producing well and one dry hole during 1960. Thus, seven producing wells and two dry holes have been drilled in the Carstairs field to date.In November 1959 a 12-section block in the Carstairs field was unitized on a surface acre basis. Mean-while, in June 1959, operators in the field executed an ""Interim Plant Agreement"" that provided the money needed to start construction of a joint venture processing plant and gathering system. Construction of the plant and gathering system was completed in February 1960."

Jan 1, 1960

Mineral engineering is defined as those engineering activities that relate to the discovery, development and utilization of mineral resources. Using petroleum engineering as an example, it is shown that the breadth of the field to be studied is a major educational problem. Breadth of field is aggravated by the rapidity with which technological demands may change. At present, special short courses serve to update engineering education. Recent experience suggests an increased rate of change for the future. The fact that engineers have typically human needs and goals, and the fact that engineers respond to these in our free society, introduces a third class of problems. One approach to the solution of these problems is the unified engineering curriculum based on a core of subject mat-ter common to all engineering. Experience suggests that the unified curriculum is an effective method to minimize the importance of the first two problem areas presented, and shows a degree of success in handling some problems within the third area. Perhaps, for the good of all segments of society, it is best to have both career-oriented and unified curricula represented by educational institutions of high quality.

Jan 1, 1963

By D. A. Akinlade, N. L. Richards, D. C. Murray, W. F. Caley

To investigate the effect of adding Ti to a Ni-Cr-Fe powder metallurgy alloy, a thermodynamic software package was used to predict the phase transformations that occurred during thermal processing. Specifically, the effect of adding 3w/o Ti to a 6w/o Al modified ternary Ni-Cr-Fe alloy (the quaternary) was simulated and the phase transformations that might occur in the material on sintering were obtained using the thermodynamic modeling tool. These predictions were subsequently compared with experimental results obtained by X-ray diffraction and metallography. For comparison, selected compacts were prepared containing only the ternary + 3w/o Ti (no Al). Based upon compressibility curves, the optimum pressure for producing the new Ti compacts was 500 MPa vs 600 MPa for the quaternary composition with Ti. In each case, hardness of the base alloy was enhanced by the Ti addition whereas the residual porosity remained relatively constant at about 19%. Finally, although SEM/EDS failed to confirm the presence of Ti in the gamma prime intermetallic, XRD spectra showed a shift in lattice parameter on addition of Ti, suggesting that the intermetallic was of the form Ni3(Al,Ti).

Jan 1, 2010

"One of the workhorses of the minerals industry is the autogenous grinding (AG) mill and its derivative the semi-autogenous (SAG) mill. These are relatively well understood, but not so Scrubbers. Scrubbers are mechanically of the same appearance/function, so what is the difference between an AG mill and a scrubber? When, or under what conditions should a scrubber be used and when should an AG mill be used? Can the processes within be mathematically modelled?In the past decades, the minerals industry has focused most of its attention on the modelling of unit processes such as cone crushers, HPGR’s, AG/SAG mills and ball mills within conventional processing circuits. Less attention has been placed on the modelling of scrubbers. This paper reviews the difference between scrubber and AG mill modelling, highlighting some of the similarities, with a view to confident comminution circuit designs.Engineering practitioners should be comfortable with these circuit designs and not shy away from considering AG mills for both small and large scale plants. AG mills can treat both harder or softer ore and scrubbers are for only softer ores. This paper differentiates scrubber and AG mill modelling in a similar way that overflow ball mills and grate discharge ball mills are analysed. Smaller scrubbers (600 kW) are suited to small scale soft ore (100-300 t/h) operations. Larger scrubbers up to 2,500 kW have the capability of very high throughput, in excess of 1,750 t/h with soft fine feed ore. AG mills are scalable up to 28 MW and are capable of treating harder ores at rates exceeding 2,000 to 4,500 t/h. Observations are that the specific energy requirements for the mill grinding duty is wide and varied. This is to a large degree the crux of the matter in sizing, as well as, differentiating, scrubbers from AG mills.INTRODUCTIONAG milling is a mature technology that has been used in minerals processing applications for more than 100 years. In the last 50 years, harder metalliferous ores have seen the introduction of steel balls to assist in the grinding/milling action. Tumbling mills used in such a configuration are called semiautogenous mills (SAG). The greater minerals industry is no newcomer to the use of fully autogenous (AG) mills. Perhaps scrubbers are. What is the difference? When should a scrubber be used versus an AG mill? How are they mathematically modelled?"

Jan 1, 2016

By J. W. Bingay

The expansion of the mining industry, with other industries, of course, is dependent upon a supply of fresh capital from year to year. Mining is a speculative form of investment, though there is a wide range of risk as between indiudual undertakings. All of the leading financial writers, nowadays, agree that expansion is being seriously interfered with by the unprecedented load of taxation Canadians are carrying. Individuals have less for investment and corporations are obliged to defer necessary expenditures in order that the demands of the taxing authorities may be met. Naturally, speculative investments such as mining exploration suffer first. Undoubtedly, a great deal of cash raised by taxes, if left in the hands of individuals and corporations for investment and expansion, would have been far more beneficially used and would have developed the country more than any use made of it by the government, in the way of bonusing new industries, or the undertaking of large schemes of development. Government undertakings of this nature are often entered into without a proper knowledge of cost and probable return. Expert expenditure of the same sums by business men or corporations undoubtedly would generally produce more prosperity for the country as a whole. The absolute necessity for lower taxation is being increasingly known to the public at large, and eventually it is hoped that our governments will see the economic impossibility of continuing the present rate of expenditure. The successful Finance Minister of the near future will not be the one who can borrow the most money.

Jan 1, 1924

By Azadeh Riahi

The main goal of this paper is to investigate the effects of permeability anisotropy in Large Open Pit (LOP) mines for problems that exhibit homogeneous anisotropic characteristics. The most important effect of the groundwater flow in open pit mines is on the stability of the pit slopes. This study will investigate the effects of having increased permeability in both horizontal and vertical directions on three aspects of LOP behavior, location of phreatic surface, pore pressure distribution and stability of slopes. The hydromechanical coupling is simulated using a one-way coupling approach. The Shear Strength Reduction method (SSR) is applied to assess the stability of slopes. The studies performed in this paper suggest that anisotropy in permeability leads to a significantly different regime of pore pressure dissipation depending on two aspects, ratio of anisotropy and the relative magnitude of permeability to simulated time. As a result, variation in safety factors and the location and depth of the failure surface must be expected.

Jun 1, 2012

By H. Sato, Y. Sato, T. Ooishi, K. Sakamoto

"Sumitomo Metal Mining Co., Ltd.(SMM)'s Niihama Nickel Refinery(NNR) produces high quality Nickel cathode, Cobaltcathode and other by-products using hydrometallurgical refining process called “MCLE”(Matte Chlorine Leach and Electro-Winning). In 2005,NNR started to use nickel and cobalt mixed sulfide (MS) produced by one of the SMM’s subsidiaries Coral Bay Nickel Corporation(CBNC)’s HPAL plant in Philippines, although its main and the only raw material until then was nickel matte. With start-up of the second HPAL plant at Taganito in 2013, NNR expanded its production capacity of nickel cathode from 41,000 to 65,000 tpa and finally achieved its target in 2015 by producing 65,980 tpa. SMM developed the technologies to improve poor reactivity of MS and installed new facilities to cope with increased Cobalt and Sulfur production at that time. This paper describes the technical approach to increase MS treatment with high efficiency.INTRODUCTIONThe Sumitomo Metal Mining Co., Ltd.(SMM)Niihama Nickel Refinery(NNR) produces Nickel cathode, Cobalt cathode and other by-products using Matte Chlorine Leach and Electro-Winning (MCLE) process technology. SMM uses nickel matte and nickel & cobalt mixed sulfide (MS) as raw materials for the MCLE process. Table 1 shows typical composition of these raw materials. Nickel matte had been only raw material until 2005, and with start-up of Coral Bay Nickel Corporation (CBNC) operation in the Republic of the Philippines, MS became major part of it. In 2009, when CBNC doubled its production capacity, NNR also expanded its plant capacity of electrolytic nickel from 36ktpa to 41ktpa, keeping an eye on the possibility of 65ktpa with oncoming SMM’s second HPAL in Philippines. Poor reactivity of MS was the prime concern at that time because our intention was to increase production with MS. Nickel extraction rate deteriorated with increasing usage ratio of MS in raw materials. To keep high nickel extraction rate under high ratio of MS, NNR developed a new leaching technology. Another concern arising from treatment of MS was Cobalt and Sulfur contents that are much more than those of nickel matte as shown in Table 1.NNR introduced new technology of solvent extraction process as to Co/Ni separation process in order to keep cost competitiveness instead of the conventional cobalt oxidation–neutralizing method. As to sulfur products, new sulfur productive facility was installed to improve the exposure to sulfur dust and the hot working conditions for workers. As a result of process development and installation of new facilities against the problem with MSusage,65 ktpa production was achieved in 2015."

Jan 1, 2017

By S. Khallouk, J. Zollinger, J. R. Kennedy, E. Bouzy, B. Rouat, D. Daloz

Titanium aluminides recently replaced Ni-based superalloys as turbine blades in the last LP stage of aircraft engines. To extend their range of use at higher temperature their properties need to be improved, either by alloying or processing. An efficient solution is to reduce the grain size during the solidification process. In the first part of the paper, an overview is given on the possibilities for grain refinement of such alloys, based on literature data and new results. The most efficient grain refinement is obtained with boron addition which leads to boride formations that are detrimental for in-use properties of turbine blades. In this work, the use of the high grain refinement potency of inoculation with non-brittle particles has been used by developing new refractory-based inoculants. The effect of one of these inoculants on grain refinement of an as-cast structure in a Ti-46Al is presented; resulting in a reduction of the grain size by a factor of 3.While less efficient compared to the potency of boron containing alloys, the grain refinement is effective and does not introduce any embrittling particles.

Jan 1, 2015

By S. Orangi

A representative sample of ramming paste from a peripheral seam in an aluminium electrolysis cell was taken in order to develop a process to fabricate ramming paste samples in the laboratory. To this end, paste material was compacted in multilayers in a mould designed to be representative of peripheral seams in Alcoa's smelters. The density distribution in the representative sample was measured ranging from 1.51-1.76 g/cm3. The density range obtained by the proposed methodology in laboratory is 1.47-1.77 g/cm3. The results demonstrate that the proposed fabrication method adequately duplicates paste density from the cell for both one and two layer compaction. Finally, preliminary results related to the compressive strength and Young's modulus of laboratory samples were obtained at various temperatures and are presented in this paper.

Jan 1, 2011

By M. N. Pons, E. Benizri, B. Laubie, A. Bani, Université de Lorraine LRGP, P. Kidd, A. J. M. Baker

"Serpentine (i.e. ultramafic) outcrops in Europe cover more than 10,000 km2 and have a low-fertility and low-productivity, making them unattractive for traditional agriculture. In general, these areas are slowly abandoned by local farmers, affected by strong rural exodus and landscapes undergo a process of closure. However, ultramafic landscapes have the potential to provide multiple ecosystem services that can contribute to Europe’s goals towards insuring food security, production of renewable raw materials and renewable energy. Phytomining (agromining) aims at cultivating metal hyperaccumulator plants that are able to accumulate Ni and other strategic elements from metal-rich soils and transport them to the shoots (>1%), which can then be harvested as a bio-ore. Such metal-rich biomass can be used to recover highly valuable metals, e.g. nickel (Ni) and also to produce energy (heat, electricity). Nickel agromining can thus offer an eco-efficient alternative to classical pyro- or hydrometallurgical processes without disturbing the soil cover and the geology from soils and rocks that would be considered as low grade ores or sterile material for conventional mining methods.Phytomining agroecosystems can lead to better soil resource efficiency and can offer a fully integrated, new agromining agriculture that could cover thousands of km2 in Europe, benefit local communities with a sustainable rural development and provide a wide array of ecosystem services which will need to be optimised under a life cycle assessment methodology:1. Production of bio-sourced metal products2. Production of energy biomass3. Restoration of soil fertility for conventional agriculture (Ni stress)4. Limiting Ni intake by local populations and farmers5. Use and conservation of local biodiversity (plant and soil fauna and microflora) as cultivated ecosystems6. Store carbon in cultivated soils7. Enhance pollination activity at landscape level.Nickel agromining could therefore change the economical balance in historically-disadvantaged ultramaficregions of Europe"

Jan 1, 2016

By E. Swartzman

"IntroductionGENERALLY, the necessity for mining coals of higher impurity content, the drive for lower costs by intensive mine mechanization, changing market requirements, and the increasing competition of oil and natural gas, have continued to result in an upward rise in coal preparation, and have necessitated a more intensive study of coal preparation problems.Increasing adoption of •continuous mining equipment, for example, is introducing new problems in coal preparation. Limited experimental work in the United States (1) shows that the effect of the continuous miner on size distribution varies with the characteristics of the seam. In some seams, the fines problem is lessened, in others it is greatly aggravated. Generally there is a decrease in the relative amount of the top sizes (plus 2 in.) and a substantial increase in the intermediate sizes (down to about 1/8 in.). Contrary to expected results•, where continuous miners with vertical-moving cutting heads are used, an increase in impurities in the slack sizes does not necessarily occur where draw-slate is taken. This is because the draw-slate tends to be kicked out in lump form. However, if a seam contains bands •and lenses of impurities they are bound to be in the mined product."

Jan 1, 1952

By M. D. Gerst

The degree to which copper will continue to be in an integral part of the world economy in the future will depend largely on the dynamics of global economic development, the primary and secondary copper resource stock, technological change, and potential environmental constraints. We have characterized the copper cycle of 1994 for all of Earth's regions and for the planet itself (T. Graedel et al., Environmental Science & Technology, 38, 1242-1252, 2004) and recently updated that cycle to year 2000. In this paper, we compare various features of the 1994 and 2000 cycles. The three largest-using regions, Asia, Europe, and North America, all increased their absolute rate of copper use between 1994 and 2000, and all increased the per-capita rate of copper use as well. Globally, the use of copper increased by about 32%, from 11.7 to 15.3 million metric tons, while population increased by only 8%. Various changes are seen in scrap trade, finished products trade, and other parameters of the cycle. We conclude by considering how the rates of technological change and growth in demand, especially in Asia, may influence the copper cycle in the years ahead.

Jan 1, 2007

By R. E. Eyre

ALTHOUGH the idea of roasting zinc concentrates in suspension had intrigued investigators for a number of years, no commercial application of a process appeared successful until the development of the "Cominco" process. The efficiency and high capacity of this process may be judged by the fact that nearly all other electrolytic plants and many zinc retort plants in the world use this method. A furnace of the Cominco type can roast without special preparatory treatment and without supplementary fuel, mineral sulphides such as zinc sulphides and iron sulphides containing varying amounts of moisture at any desired rate ranging from one-half up to full capacity. The full capacity of a unit is in general about three times that of a multiple hearth furnace of the same size. The latest type of "Cominco" furnace can be built for capacities from 25 to 500 tons per day. The quality of the calcine is subject to positive control and may be

Jan 1, 1961

By Matthew Scott

Introduction The refining of precipitate is the final stage of all the processes involved in gold mining and cyanide milling, by which the precious metal is at last obtained in a concentrated form, which can be accurately valued and marketed. Possibly one ought to say, conveniently shipped, for accuracy in valuation depends in many instances on a toughening treatment given the bars as received at the Mint so as to obtain a homogeneous metal that lends itself to representative sampling; which, of course, entails a surcharge on the regular Mint charges for the extra work necessarily undertaken. There are several methods of refining zinc-gold precipitate, each with its advocates; the method employed depending not always on the quality of the bullion produced but on the local exigencies of the case in point. These methods are more or less detailed in various textbooks and it is not the purpose of this paper to discuss them, but to confine ourselves to the specific case as stated in the title of the paper. At the outset, it behooves the writer to express his thanks to Mr. Brigham, the General Manager of the Hollinger Mines, for the kindly consideration and encouragement given in developing this process. This will be better understood when one considers the immense values involved, tending towards conservatism in practice, and making one chary of radical innovations. This process has been in satisfactory operation now for about two and-a half years, during which time over twenty-five million dollars value in fine gold has been produced, so that it may be reasonably held that the process is successful.

Jan 1, 1931

By A. Hynes, T. Skulski, D. Francis

The Archean volcano-sedimentary succession in the LG-3 area has undergone two phases of deformation and has been metamorphosed to upper greenschist and amphibolite facies. Marine, fine-grained sediments and mafic pyroclastics comprise the lowest observed stratigraphic unit. These sediments are overlain by a thick sequence of submarine basalts and minor basaltic andesite. The lavas are characterized by high Al/Al+Si, Ti values, low Mg numbers and flat REE profiles (lOx chondrite). A sedimentary prism of coarse elastics which was deposited close to an exposed plutonic highland, overlie the volcanics. Massive lavas of basaltic andesi te and associated volcano-sediments comprise the uppermost stratigraphic unit. These lavas are characterized by high Mg numbers, Ni, Cr, LREE (lOOx chondrite) but low Ti, Al/Al+Si and HRee. The supracrustal rocks were intruded by tonalites and tonalitic gneisses.

Jan 1, 1984

By D. Jean Hutchinson, Mark Diederichs

"Cable bolts are an important support component in modern underground mines. If an optimized cable bolt system is to be achieved, it is insufficient to focus on cable bolt layout design or on cable bolt installation in isolation. Cable bolt support, like all engineered systems, requires a holistic approach, encompassing integrated elements of design, implementation and verification. The “Cable bolting Cycle” described in this paper incorporates these components along with related tools and procedures which should be used together to ensure effective and efficient cable bolt support.Design involves the consideration of demand, capacity and constraints as outlined in this paper. The demands imposed on the sup-port system by the rock mass response to excavation under the combined action of stress and gravity must be matched to the capacity of the cable bolt array. The cable bolt system capacity is a function of the component strengths of the steel strand and the bond (load transfer) and by the deformation response and retention characteristics of the system. The design is bounded by operational and economic constraints.Implementation of the cable bolt array can then proceed and must include appropriate protocols of communication, training and quality control, in addition to both general and site specific installation procedures. Implementation will be discussed as the sum of these components.Implementation of the cable bolt array can then proceed and must include appropriate protocols of communication, training and quality control, in addition to both general and site specific installation procedures. Implementation will be discussed as the sum of these components.The information presented in this paper represents a very abbreviated version of much broader concepts, procedures and design charts, presented in a practical cable bolting handbook by Hutchinson and Diederichs (1996)."

Jan 1, 1996

By N. Shi, T. G. Joseph

ABSTRACT Before any large plant is moved onto an oil sands dominated surface, particularly those surfaces encountered in-pit, it is imperative that the ground be evaluated for bearing capacity. A 2230 tonne mobile in-pit hopper/crusher facility designed for operation in the Canadian oil sands was modeled. This evaluation focused on track and outrigger pad versus ground interactions as the key performance indicators of appropriate ground performance below the unit in both operating and repositioning propel modes. A study of cyclic oil sand behaviour was also inferred from laboratory cyclic plate load data as an extension of the simulation model indications.

Jan 1, 2013

By Scott Beer

What New Technologies Will Drive Economic Improvements? ??Historical ?1060?s: Mainframe Technologies ?1970?s: Mini Computing ?1980?s: Workstation Computing ?1990?s: Personal Computing ?2000?s: Network Computing Internet PDAs Cellular phones ??What?s the next technology improvement? ??What?s next for Mining?

May 1, 2009

By M. M. Papic

"This paper describes the Sasol coal liquefaction process, as used in South Africa. It covers coal supply, coal gasification, gas purification, Fischer-Tropsch synthesis, the major utility systems involved and the economics of the process.IntroductionThe Sasol coal liquefaction process is based on Fischer-Tropsch synthesis of liquid fuels from carbon monoxide and hydrogen, which are in turn obtained by gasification of coal with steam and oxygen. The process is shown schematically in Figure I.The first step in the process is coal preparation, in which the coal is crushed and screened to a 3-50 mm size for gasification on one side and to -3 mm size for steam and power production on the other. Oxygen needed for coal gasificatoin is produced in the air separation plant.Coal is gasified under pressure by steam and oxygen in the Lurgi gasification plant, where raw, impure gas is produced . The raw gas is first washed in a scrubber with a circulating gas liquor, heat is then recovered from it in a waste heat recovery boiler and the gas is further cooled for purification. Water-insoluble materials (tar oils) in the gas liquor are separated from aqueous solution and sent to tar refining for the recovery of tar products. The aqueous portion of the gas liquor goes to a Phenosolvan solvent extraction process, where phenols and ammonia are recovered. Water then proceeds to the effluent treatment plant.The scrubbed and cooled raw gas goes to a Rectisol gas purification plant, where all components other than hydrogen, carbon monoxide and methane are removed as completely as possible by absorption in refrigerated methanol. The acid gases (CO2, H2S) stripped from the methanol in the Rectisol unit are processed in a Stretford plant for recovery of sulphur. Regenerated methanol is returned to the process. The purified synthesis gas is passed to the fluidized-bed Synthol reactors, where Fischer-Tropsch synthesis reactions take place.The synthesis products are recovered in a product recovery unit as separate streams of decant oil containing higher-molecular- weight hydrocarbons, light oil comprised of lower-molecular- weight species, the aqueous stream containing water solubles, a C3/C4 stream, a C2 stream , a methane stream and a hydrogen-rich stream. Most of the hydrogen is recycled to the Synthol reactors; a major portion of the methane is reformed to hydrogen and carbon monoxide for recycle; the C2 fraction goes to an ethylene plant; and liquid streams proceed to the product refinery.The product refinery is used to upgrade and purify the Synthol products to specification fuels and chemicals.Sasol l, the first coal liquefaction plant in South Africa , was built in 1955. It is still operating and has a product output of about half a million tonnes per year. The Sasol II plant is in a commissioning stage and will be in full operation in 1981. It is about five times the size of Sasoll. It uses over 12 million tonnes of coal and produces more than 2 million tonnes of saleable products annually (1,2,3). The Sasol llI plant, which is a mirror image of Sasol II, is under construction and scheduled for completion in 1983."

Jan 1, 1981

By J. M. Mwase

The platinum group metal (PGM) industry is currently reliant on the crush-mill-float-smelt-refine route to process PGM ores. However, there are many instances where this route would not be feasible. An alternative process route has been developed which involves heap bioleaching to extract base metals followed by heap reclamation and a water wash step, leading into heap cyanide leaching to extract precious metals. This process was evaluated through test work on samples of Platreef ore using laboratory scale columns. After 304 days 75% Ni and 93% Cu were extracted in the bioleach experiment at 65°C, and after 60 days 58% Pt, 99% Pd and 90% Au in the follow-up cyanide leach experiment at 50°C. A preliminary process flow sheet has been developed around this. Analysis via a mineral liberation analyser showed that the remaining Pt was in the form of the mineral sperrylite, which appeared to be slow leaching in cyanide in comparison to the other mineral types. Analysis of cyanide effluent solution showed high levels of thiocyanate, which present an environmental risk for disposal and high consumption of cyanide. Further studies to develop the process for commercial application in the South African PGM industry are outlined.

Jan 1, 2014