Search Documents

By B. N. Church, R. H. Seraphim, J. T. Shearer

"The Lexington-Lone Star CU-Au deposits straddle the Canada U. S.A. border, south of Greenwood, British Columbia. This 3 km long linear porphyry system occurs in a northeast dipping belt of sheared quartz porphyry and serpentinite. The best grades of mineralization occur in three principal bodies known as the Pit zone, the Northwest zone and the Lexington Main zone. The Pit zone at the Lone Star mine is the largest of the mineralized bodies and consists of fracture fillings and disseminations of pyrite, chalcopyrite and minor molybdenite, hosted by the Lexington quartz porphyry. The Northwest zone, discovered by drilling through overburden near the 49th Parallel, consists of pyrite-chalcopyrite-gold mineralization in the quartz porphyry and the footwall serpentinite. The Lexington Main zone has the highest grade of gold and occurs near the footwall of the quartz porphyry with the mineralogy and setting similar to the Northwest zone. Alteration of the host quartz porphyry is mostly sericitic and chloritic; alteration in the adjacent serpentinite is mostly talc and carbonates.A weighted average of the drill-indicated reserves is 19.5 million tonnes grading 0.56% CU and 0.55 gl t Au.IntroductionThis paper describes copper-gold mineralization associated with the Lexington quartz porphyry in the Greenwood mining camp of south-central British Columbia and adjacent parts of Washington State (Fig. 1).Access to the property is mainly by a network of farm, logging and old mining roads to the U.S. border, 10 km south of Greenwood, British Columbia."

Jan 1, 1995

By E. A. Morris

It has been shown that Alberta oil-sands fluid coke can be effectively used to reduce SO2 to elemental sulphur while simultaneously producing sulphur-impregnated activated carbon (SlAC). In the capture of mercury from industrial flue gases, SIAC has proven to be a highly effective adsorbent material. The current research aims at developing an existing SlAC technology to meet the needs of copper smelters for mitigating both mercury and SO2 emissions, while making elemental sulphur as a co-product. The challenge behind this undertaking is that these flue gases generally contain percent levels of 02 and H20 vapour (2-12%). The focus of this study is therefore on the feasibility of reducing SO2 using fluid coke under copper smelter flue gas conditions, as well as the optimisation of SIAC properties for capturing vapour phase mercury. It is hypothesised that mercury capacity is strongly affected by the 02 potential of the activation gas due to changes in surface sulphur types arising from different reduced sulphur species. To verify this, gas chromatography is used to analyse the reaction products while XPS and XANES will be used to describe the nature of sulphur on the SlAC surface. CVAFS analysis of mercury capacity will finalise the hypothesis assessment. Preliminary results indicate that 02 at 5% does not play a significant role in SSA or pore development. As expected, increased residence time contributes to SO2 reduction and elemental S yield.

Jan 1, 2007

By S. Koppalkar

ABSTRACT: The development and evolution of the gravity recoverable gold (GRG) test procedure at McGill University is reviewed in this paper. Since the late 1980s, the research group led by the late Professor André Robert Laplante at McGill University has undertaken fundamental studies and applied research of the Knelson concentrator to develop a sustainable method of estimating GRG. Historically, a concept of “free gold” was used, and it was de?ned as the gold that could be separated and recovered from gold ore by amalgamation. Due to health and safety hazards, the practical use of amalgamation has declined. Around 1994, a methodology using a 3-in Knelson concentrator to measure gravity recoverable gold was established at McGill University. As a result of more than 10 years of improvement and optimization, this technique has become a standard method of evaluating GRG for gold ores, gold plant streams and platinum group metals. By 2006, about 200 GRG tests were carried out at McGill University on ores from all over the world. Recently, a modi?ed version of the GRG test (a simpli?ed test) was developed to provide a quick and rough estimate of the GRG in a sample; this simpli?ed test has the advantage of reduced mass, processing time and cost. To recognize and honour the contributions made by the late Professor Laplante towards the establishment of a standard test procedure for assessing gravity recovery potential, the authors propose that the GRG test be named after Laplante.

Jan 1, 2010

By Andrew Matyas

"During the summer of 1968, the author was employed in the Research Department of Dominion Foundries and Steel, Limited, Hamilton, Ontario. Over the years, Dofasco has been conducting a program for developing more efficient control of its basic oxygen steelmaking process. The author was thus able to obtain a variety of viewpoints from both research engineers and furnace operators. He also had access to extensive literature dealing with BOF control schemes underway at other major steel producers. This paper describes the present state of developments in BOF steelmaking control.The necessity for efficient BOF control is pointed out. To appreciate the variables to be controlled, a brief outline of process fundamentals is included. Technical aspects of present methods of practical control are examined in detail; the relative merits of dynamic over static control models are emphasized. Finally, it is shown how an effective dymic-optimizing control scheme serves as the basis for closed-loop computer control of the process."

Jan 1, 1970

By M. Jackson, R. McDonald, T. Osken, D. Robinson

"The addition of sulphidic materials in the leaching of nickel laterites has several potential benefits that include improvements in the rheological behaviour of the blends, reductions in the sulphuric acid and steam requirements, sweetening of the nickel grade of the combined feed material, and the option of using a range of sulphidic materials. The current study examines the oxidative processing of 30% w/w blends of nickel concentrate and nickel laterite ore at 250oC. In particular, the viability of using low oxygen overpressures was examined for significant amounts of nickel flotation concentrate, up to 12% w/w. Further to this the impact of process water quality, in particular the presence of chloride, upon the kinetics of extraction and the mineralogy of the residue were also investigated. This paper will present the results of preliminary work in this area.INTRODUCTIONThe use of sulphidic ore as a source of sulphuric acid during oxidative hydrometallurgical processing is not a novel idea and can be traced back over forty years (Seidel & Fitzhugh, 1968). A series of patents pertaining to application of this approach for laterite ores can be subsequently found (O’Neill, 1973; Opratko et al., 1974; Rodriguez, 2008a, 2008b; O’Callaghan, 2010; Liu et al., 2011) and a few of articles containing published data (Ferron & Fleming, 2004; Quinn et al., 2009). The use of pyrrhotite tailings as a source of sulphuric acid has also been employed for the leaching of converter slags (Perederiy et al., 2011).It is known that hydrometallurgical operations such as the HPAL plant at Murrin Murrin have added small amounts of sulphides as either transitional (mixed sulphide/oxide) ore or non-smeltable concentrate. This can improve the rheology (Rodriguez, 2009) and provide heat credits. However these plants are generally limited in their ability to add such materials due to their reducing nature and given under highly acidic conditions that the breakdown potential of the titanium used for the autoclave lining is significantly reduced. A suitable oxidant must therefore be present to ensure the potential remains sufficiently high."

Jan 1, 2012

By S. McPherson, M. Chalkley, R. Ellenwood, W. Nicot

"The Moa JV was formed in December 1994 as a 50/50 joint venture between Sherritt Inc. and General Nickel Company S.A. of Cuba. The joint venture consists of the mine and Pedro Sotto Alba processing plant in Moa, Cuba and the Corefco refinery in Fort Saskatchewan, Alberta, Canada. Throughout its now nearly 23-year history, the Moa Joint Venture has faced a number of global, operational and process challenges. Global challenges have included high input costs such as for fuel oil and sulphur, as well as low nickel prices. Operational and process challenges have included increasing ore haulage distances, decreasing ore Ni + Co grades, and increasing ore impurity contents. For example, increases in impurities such as Mg and SiO2 in the ore result in increasing acid demand in leaching and decreasing solids content of preheated leach feed slurry, respectively. In spite of these challenges, the mixed sulphide production capacity from the Moa Joint Venture has increased from 12,500 to 37,000 t/y Ni + Co since 1994 by judiciously targeting expansion projects and by continuously performing process and operational improvements.INTRODUCTION The Pedro Sotto Alba high pressure acid leach (HPAL) plant at Moa Bay, Cuba has a long history (Maslenitzkiy, 1969; Chalkley, 1996; Carlson, 1960; Roy, 1961; Carlson 1961). The plant was constructed by Moa Bay Mining Company and started up in late 1959 after several years of process development by Freeport Nickel Company, including operation of a 10 t/d plant in Hoskins Mound, Texas and a 50 t/d plant in Port Nickel, Louisiana (Southwick, 2004), as well as development work by Chemical Construction Company (Chemico) to precipitate metal sulphides (Roy, 1955a; Roy, 1955b). The Moa plant had an original reserve of 50,000,000 t of ore, graded at 1.35 wt% Ni, 0.146 wt% Co, 3.70 wt% Si, 1.00 wt% Mg and 4.5 wt% Al. At original design rates of 2,000 kt/y of ore, the design capacity of the plant was around 25,000 t/y Ni + Co as a mixed sulphide product, which would be shipped to the Port Nickel Refinery in Louisiana for processing. In 1960, the plant changed ownership and was restarted in 1961 under Cuban management. Between 1961 and 1989, the plant was also supported by involvement from the former USSR, supplying spare parts and consumables. In 1994, Sherritt Inc. partnered with the General Nickel Co. S.A. of Cuba and formed the Moa Joint Venture. This joint venture includes the mine and Pedro Sotto Alba HPAL processing plant in Cuba and the Corefco refinery in Fort Saskatchewan, Alberta, Canada. Under this partnership, ore is processed in Cuba to produce a nominally 55 wt% Ni and 5 wt% Co mixed sulphide product that is shipped to Canada and processed by Corefco to produce class 1 nickel, high grade cobalt and byproduct ammonium sulphate fertilizer."

Jan 1, 2017

By Douglas W. Reeve, Hoc Nghia Tran, David Barham

"In kraft pulp mills, the spent pulping liquor is concentrated and used as fuel in the recovery boiler. Extensive deposits are formed in the upper section of the boiler due to the very high ash content of the fuel and the volatite nature of the ash. Deposits are composed of Na2S04, Na2C03 NaCI, some potassium salts and reduced sulphur compounds. Chloride and potassium salts are enriched in the deposits compared to the smelt due to their greater volatility.Severe corrosion of the superheater tubes in a recovery boiler has been traced to three factors: a non-uniform temperature profile in the flue gas, relatively high operating steam temperatures and high chIoride and potassium concentrations in the fireside deposits.The role of chIoride and potassium in superheater corrosion has been explained by increased Iiquid phase in deposits. Together with corrosion studies, this information has shown that kraft recovery boiler superheater corrosion due to the chloride and potassium enriched deposits can be avoided by proper boiler operation and by judicious superheater and furnace design.IntroductionThis investigation of recovery boiler superheater corrosion was initiated by the discovery of severe corrosion of the final stage superheater in a Canadian closed cycle kraft pulp mill(1,2). Metal wastage leading to tube failure was believed to be due to three major causes : the relatively high operating steam temperatures, the uneven distribution of flue gas temperature across the boiler which created a "" hot spot"" and the high chloride and potassium concentrations in the superheater fire side deposit. The mill responded to the problem by i) lowering the superheater steam temperature from 475°C to 380°C, ii) minimizing the chloride content in the spent pulping liquor, by controlling the NaCI input with recovered bleach plant effluent, and iii) changing metallurgy of a portion of the bottom section of the final stage superheater platens from ferritic steel T-22 (2.25% Cr, 1% Mo) to austenitic steel Incoloy 800H (21% Cr, 32% Ni, 46% Fe, 1.5% Mn, 1% Si, 0.6% Al) (Fig. 1). Details of the superheater corrosion experienced in the closed cycle mil! have been reported in previous papers(l ·2,) ."

Jan 1, 1984

By F. Cheuk, E. Krause, V. G. Papangelakis, G. A. Moldoveanu, S. Abendschein

Systematic studies have been conducted at the University of Toronto in order to evaluate lanthanide extraction from clay minerals from different geographical regions. It was found that rare earth elements (REE) are easily recovered into an aqueous solution via an ion exchange mechanism by leaching with electrolyte solutions containing monovalent cations under ambient conditions. In this study we assessed extraction levels of individual REEs as a function of initial clay composition and leaching conditions. It was found that, in spite of variations in clay origin, all clays consistently reached peak REE extraction levels with fast kinetics. However, terminal extractions were clay-specific. The feasibility of using seawater as a leaching solution and potential synergies with ammonium sulphate as a lixiviant was also investigated. Seawater was found to be inferior to using ammonium sulphate, and provided no observable synergy in leaching performance when used together. The aqueous phase trapped in leached clays was shown to contain significant amounts of REE, as demonstrated in clay washing tests. Techniques to improve the REE concentration in leachate through process variations were investigated. However, it was found that most techniques capable of increasing REE concentrations in the resultant leachate also resulted in reduced REE extraction.

Jan 1, 2014

By Gordon G. Duncan

Historical Sketch Occurrences of native copper have been known along the Arctic coast of Canada, especially in the vicinity of the. Coppermine river, since the early part of the eighteenth century (See map, Figure 2, insert). In 1769, Samuel Hearne, a clerk of the Hudson's Bay Company at Fort Churchill, was sent to explore the 'copper mines' from which natives had been reported to secure copper for tools, fishing spears, etc. After two successful attempts, he reached the Coppermine river in 1771, accompanied by Indian guides. This hazardous trip was indeed a remarkable feat when one considers the vast distance covered, a great deal of which was barren lands. At Bloody falls, (See Figure 1) on the Coppermine river, Hearne's Indians swooped down on a party of sleeping Esquimaux, who gathered there each summer to fish, and murdered the entire band encamped on that side of the river. Hence the name of the falls. Hearne's knowledge of minerals was undoubtedly limited. He reported having seen the copper mines from which the natives were securing the copper, but he failed to prove the economic possibilities of the copper occurrences or to give an accurate description of any deposit. Sir John Franklin visited the area in 1821. He and other members of his expedition, namely, Richardson, Back, Kendall, and Hood, reported native-copper float to occur in the vicinity of the Coppermine river and Bathurst inlet.

Jan 1, 1931

By Guy Demers

"This paper defines the responsibilities and functions of the Maintenance Department, and its organization, physical and human assets, highlighting the unique operating problems. Due to the self-sufficient aspect of the Asbestos Hill Deception Bay project, the Maintenance Department cover-s fields that are numerous and very dissimilar: production, mobile, processing, service, power generation, fire protection, heating, water and sewage disposal equipment. Added to this, buildings, plant and camps, wharves and communications equipment all demand versatility, adaptability and expertise from maintenance personnel. Good maintenance practices are a necessity in this environment and are more critical than at southern locations; that is, high-quality replacement material, complete and well-controlled preventive maintenance, major repairs on a component-replacement basis, updated inventory, efficient training and permanent contacts with suppliers, combined with an equipment improvement program, updated specifications on lubricants, hoses, seals, filters, etc., are mandatory. The seasonal aspect of the operations applies a great deal of pressure on the maintenance team, as the production months do not permit major repairs. Short- and medium range planning and accurate evaluation of equipment conditions highly influence production efficiency. Maintenance control, planning and scheduling do not follow the accepted standard routines, as personnel turnover normally does not permit an accumulation of knowledge of the equipment history and condition by the •individual tradesman."

Jan 1, 1976

By Louis Frost

"Dominion No. 17 Colliery, of the Dominion Coal Company, Limited, is located in the district of New Victoria, N.S., at the entrance to Sydney harbour.This Colliery was opened in 1882 to work a submarine area of the Harbour seam (see Figure 1). It was closed in 1921 and the mine, which has a make of water of approximately 250 gallons per minute, was allowed to fill.No. 18 Colliery, situated almost a mile to the east, was opened in 1938 to work the Phalen seam in this area with the intention, later, of driving a cross-measure tunnel to mine the section of the Harbour seam lying between No. 17 Colliery and the Princess Colliery of the Nova Scotia Steel and Coal Company, Limited.In 1945 it became necessary to open this area in the Harbour seam and a cross-measure tunnel was driven from the existing workings of No. 18 Colliery in the Phalen seam, which underlies the Harbour seam at a depth of 500 feet.The tunnel was started in 1946 and completed in 1948. The cost of opening this section, which contained only 6 1/2 million tons of coal, made imperative the recovery of all the available coal and precluded the maintenance of the large barriers that had been left in No. 17 Colliery for impounding the water, especially as the maintenance of these barriers would have meant the loss of 885,000 tons of coal, or 12.3 per cent of the whole tonnage available. Therefore, a study was made to determine the best means to dewater the 250 million gallons of water lying in the old No. 17 Colliery."

Jan 1, 1952

By D. C. R. Espinosa, P. Aliprandini, F. P. C. Silvas, J. A. S. Tenório, M. M. Jiménez Correa

"Nickel ores are divided into two types: sulfide deposits and lateritic deposits. About 60% of nickel resources are found in laterite ore, while the remaining 40% is contained in sulfide ore. Laterite ore is usually processed via pyrometallurgical means or through hydrometallurgical techniques that include acid leaching and metal value recovery from solution. In this study, copper and nickel adsorption by Dowex M4195 ion exchange resin from an acidic sulfate liquor was investigated. The acidic sulfate liquor was collected from an atmospheric leaching process (AL) of laterite ore. Ion exchange experiments were conducted in a batch system by varying parameters such as pH, time, metal concentration and temperature. Initially, mono-elemental synthetic solutions of nickel and copper were used in the experiments and then a synthetic solution simulating AL liquor was tested. Test results showed that the resin exhibited high selectivity towards copper and nickel, however, a high concentration of iron in the synthetic AL solution interfered with the recovery of nickel and cobalt by the resin.INTRODUCTION Nickel is one of the most important industrial metals in the world. It is widely used in industrial applications, such as the production of stainless steel, magnets, electroplating and special alloys (Dizge et al., 2009). The main sources of industrial nickel production are sulphide deposits; only 40% of industrial production uses lateritic ores. However, it is estimated that 60% of global nickel resources are found in nickel laterite deposits (Kuck, 2016). Since industrial nickel demand continues to grow, the development of new technologies for the extraction of nickel from laterite ores has become an interesting research topic (Agatzini-Leonardou, 2009)."

Jan 1, 2017

By G. W. Poling, J. R. Hoffert

"A common practice in preventing gravity-fed tailing pipeline from plugging due to sanding is to add lime at relatively high dosage rates. The lime affects the rheology of the slurry ""vehicle"" which transports the coarser particles in a heterogeneous flow-regime. This paper describes a study of the effect of lime on the critical deposition velocities and friction head losses of Highmont Mining Company's mill tailing. Testwork using an extrusion viscometer was related to the surface chemistry changes brought about by the high lime additions. Lime additions which typically increased the tailing pH from 8.4 to 11.5 reduced the critical deposition velocities from approximately 3.2 to 1.7 m/sec.IntroductionCommon practice, at least in base metal concentrators in British Columbia, is to use high lime additions in tailing slurries when the pipeline becomes partially plugged with sands. Some concentrators, such as the Highmont Mining Co. Ltd. plant, add lime on a continuous basis during low tonnage periods and during startup/shutdown transition s. Although such high lime additions often solve temporary plugging problems, the effect of lime on slurry rheology has not been well understood.Slurry pipelines are designed to transport solids in suspension with a minimum of wear and without particle deposition. These two objectives are in opposition because the velocities required to maintain solid suspension can sometimes cause high head losses in the pipeline, as well as wear problems. Thus, the optimum velocity for a long distance slurry pipeline is in the range that provides just enough turbulence to keep coarse particles in suspension."

Jan 1, 1985

By Lloyd W. Trevoy

Titanium and zirconium heavy minerals occur in the tailings streams from processing plants which use the hot-water extraction process for recovery of bitumen from tar sand. In a research program conducted by Syncrude Canada Limited, the crude tailings stream was upgraded to produce quality zircon and titanium mineral products. To process the tailings through conventional upgrading equipment, bitumen residues must first be removed from the mineral grains. Then, by gravity separation, fines and coarse sand grains were removed and a 71% heavy minerals concentrate was prepared which was further separated by high-tension equipment into zircon and titanium minerals concentrates. The zircon concentrate was upgraded by gravity, magnetic and high-tension cleaning to produce a high-quality 98% zircon product. The titanium minerals concentrate was separated into rutile, leucoxene and ilmenite fractions. Heavy minerals distribution in tar sand drilling core samples has been evaluated for various locations on Syncrude Lease 17, and expected annual production levels of heavy minerals have been estimated. A preliminary evaluation has been made of the potential for zircon, leucoxene and rutile production and for further upgrading of ilmenite and leucoxene to synthetic rutile for titanium dioxide pigment production.

Jan 1, 1978

By P. C. Santos-Munguía, F. Nava-Alonso, O. Alonso-González

"The gold recovery of a Mexican cyanidation plant, in Sonora, has been decreasing due to the increasing presence of gold tellurides. This work presents the results of different processes aimed to recover the remaining gold from the cyanidation tailings of the operation. The cyanidation in the mine is performed at 0.1 g/L NaCN and pH = 10.3, adjusted with lime. The treatments studied in the laboratory with these tailings were: cyanidation at higher cyanide concentration than that used in the plant, cyanidation with oxygen injection, cyanidation with oxygen and lead nitrate addition, and thiourea leaching. The results obtained with each of these treatments are presented and discussed with the final objective of proposing a method to recover the gold associated with tellurium.INTRODUCTION It has been demonstrated that gold telluride is refractory to the conventional cyanidation process and, for this reason, some alternative methods to recover precious metals from tellurides have been proposed. (Zhang et al., 2010). These include cyanidation with modified conditions or the use of non-cyanide leaching agents. This work presents the gold leaching results of tests performed with a sample of cyanidation tailings obtained from a Mexican deposit containing telluride species. The mine exploits a mesothermal deposit with a molar Te/Au ratio of 1, containing also lead, molybdenum, bismuth and tungsten. Gold is recovered from the ore by standard cyanidation, however, lately the gold recovery has decreased, likely due to the tellurium content of the ore. The sample used in this work was the cyanidation tailings of this deposit. It was treated in the plant by cyanide heap leaching (0.1 g/L NaCN, pH = 10.3 adjusted with lime). Some gold remained after the cyanidation and it was thought that this gold was associated with tellurium. The objective of this work was the recovery of the remaining gold from the tailings by an alternative process."

Jan 1, 2017

By J. D. T. Steyl

"This paper presents a phenomenological model of the rate of iron(III) precipitation in batch and continuous autoclaves at medium temperature operating conditions. The rate expressions are based on information obtained from the literature and experimentation at low and high pulp densities. Special allowance is made for the formation of surface nuclei, which appears to be promoted at a higher iron(III) precipitate surface area, especially in suspensions of lower terminal acidity. This leads to the formation of secondary particulates and provides the required link to simulate high pulp density leaching-precipitation systems, using low pulp density batch precipitation data. In particular, the model allows direct application of the simulation to the autoclave oxidation of iron-containing copper sulfide concentrates and provides a good estimation of the relative precipitation rate of hematite, the preferred product, compared to hydronium jarosite. Some interesting mechanistic understandings of iron(III) precipitation in autoclaves are further elucidated.INTRODUCTIONThe objective of this work is to describe the rate of iron(III) precipitation and the relative amounts of hematite compared to hydronium jarosite precipitation during batch and continuous chalcopyrite oxidation under medium temperature (MT) (~130 to 160ºC) autoclave conditions. Published information has not yet revealed sufficient mechanistic insights about this sparingly soluble salt system under these conditions. The rate expressions in this paper are based in part on current literature information, supplemented by qualitative experimental observation at low pulp density conditions, in particular the high-resolution backscatter electron (BSE) images and particle size distributions (PSDs) of the precipitates. A summary of this work and insights from the literature are presented first, after which the behaviour of iron(III) in high pulp density leaching systems is used to derive a phenomenological expression of the effect of existing iron(III) precipitate surface area on the precipitation rate. The overall regression encapsulates all the experimental results, i.e., those obtained in both batch and continuous autoclave configurations (Steyl, 2012a)."

Jan 1, 2012

By K. C. Hendrick

The paper will review the significant developments in world copper over the past ten years and their impact on the Canadian industry. It will also examine the outlook for the future.

Jan 1, 1971

By Lawrence Bragg

WE associate metals with hardness, toughness, and strength. But a curious paradox lies at the root of the valuable mechanical proper-ties of the metallic state: in order to be strong, a metal must be weak. This paradox, and the equally surprising fact that, in a sense, metals are not true solids at all, are among the topics here discussed by Sir Lawrence Bragg. (1) WHAT METALS MEAN TO US We employ various materials to build or fabricate the many objects we use in everyday life, choosing those whose properties are most suitable for the purpose which the object has to serve. Certain of these materials have been used from the earliest times, such as stone, wood, leather, and animal or vegetable fibres, each with its own peculiar valuable properties. Stone resists crushing and is very durable and permanent, as indeed it must be, since it has so long resisted change as a part of-the earth's crust. It is there-fore ideal for walls and buildings, and very early in his history man discovered how to make artificial stones by burning clay, with the advantage that they could be given any desired shape, and made into bricks or given elaborate forms as pottery. Wood is strong and tough and light, it resists tension as well as compression, and is nor brittle like stone. It forms beams and furniture and parts of tools or weapons. Leather is tough but at the same time iris flexible; it is ideal as straps or sheers. Vegetable fibres such as linen or cotton, and animal fibres such as wool and silk, owe their value to their flexibility and strength in resisting extension. They can be spun into yarn or rope, and woven into cloth. The technological age in which we are now living is replacing the natural products used by early man by a series of artificial products, but it is remarkable to see how in nearly every case we are copying Nature's materials. The wide use of concrete represents a developed art of making artificial stone. Artificial fibres such as rayon or ?nylon replace cotton, wool, and flax. Plastics are coming very much to the fore; they correspond to early man's use of horn, another substance with peculiar properties of roughness in all directions without the 'grain' of wood. For the most part we are following in the footsteps of our remote ancestors, though we can make for ourselves what they had to cull from wood and field. There are exceptions; for instance, we have discovered comparatively recently the number of uses to which natural rubber can be put, and are now making it artificially. This is a really new discovery; our ancestors had nothing with such remarkable powers of elastic stretching without breaking, and resistance to being abraded.

Jan 1, 1943

By D. J. M. Farnsworth

Since the 1.940's, the bulk of the ore production from the Sullivan Mine has come from pillars. These pillars, located from 100 to 2000 feet below surface, have been subjected to considerable ground pressure. Mining techniques were adopted to minimize the problems of deteriorating ground conditions. These techniques included an orderly sequential blasting of pillars along a retreat front, stage blasting of tall pillars in horizontal slices and utilization of broken pillars as "buffers". The latter two techniques involved leaving substantial tonnages of broken ore in place for as long as 4 years. Rapid oxidation of metal sulphides, with attendant heat and noxious gas generation, had occurred in a few very localized areas of the mine associated with a major water course. However, in a very short period starting in 1972, sulphide fires spread to several of the large blocks of broken ore that had been left inactive for lengthy periods. There proved to be no feasible method of extinguishing these fires, except by complete removal of the burning ore. The attendant problems of handling large tonnages of burning ore have had considerable negative impact on the mine operation. The chemical reactions involved in these sulphide fires have been studied by the mine staff to determine the conditions necessary for' initiation and propagation of the tires. Techniques to safely and efficiently handle hot ore have been implemented and refined. Lastly, and most important, mining methods at the Sullivan Mine have been revised to ensure that additional fires do not occur.

Jan 1, 1977

By A J. Kyle

After a brief description of the shaft and surface facilities, this paper describes the planning for the mining operation, the selection of equipment the general method of mining and the sequence of operation. All of the major items of equipment are described, including the components of the power system. The detailed planning is reviewed -from the shaft sinking to the three-shift mining operation. Excavation and equipment changes, as well as long-range planning, are al o di cussed. Introduction THE successful completion of the Yarbo No. 1 shaft of International Minerals & Chemical Corporation (Canada) Limited in July, 1962, added a new type of mine to Canada&apos;s many producing operations. IMC Esterhazy is a unique mining operation in Canada; in fact, it is unique to potash mining in general. Not only is thi&apos;3 a trackless operation utilizing shuttle cars and belt conveyors in its material handling systems, but it excavates all of the ore with continuous boring machine<:;.

Jan 1, 1964