Search Documents

By A. K. Alzo?ubi

Block toppling in natural rock slopes has been under investigation since the 1970?s. De Freitas and Watters (1973) introduced the term ?toppling? to describe the movements of rock slopes by rotation in steeply dipping beds. The Lornex pit case history from British Columbia (Canada) was chosen to study the effect of mining on the stability of toppling rock slopes. A discrete element approach that allows fracturing of intact material was applied successfully to model the composite rock slide-rock topple movement. Three main movement modes were observed in the field and the numerical model; the sliding of the top of the slope exposed normal scarps, the toppling at the middle part of the slope exposed obsequent scarps facing opposite to the slope face, and dilation of the rock caused by fracturing at the toe formed loose material. The development of the rupture surface at the toe of the slope was traced and did not evolve into a continuous rupture surface throughout the slope both in the field and the numerical simulation. Good agreement was achieved between the deformations recorded in the field and the numerical simulation.

Jun 1, 2012

"The successful commissioning and ramp up of the Albion Process™ at the GPM Gold Project relied on the successful scaling up of the process from batch and continuous pilot plant campaigns (Voigt et al., 2015). Critical information about reaction kinetics and residence time, grind size and pulp density were determined at the laboratory scale and successfully applied to the commercial scale. A limitation of small scale testwork, is that some parameters cannot be measured reliably and scaling up is a function of the physical size of the equipment which isn’t possible to test with laboratory scale equipment. Oxygen mass transfer rate is one such parameter since this is a complex interaction of many factors including slurry temperature, solution and slurry chemistry, slurry viscosity, agitator type, dimensions and power, oxygen bubble residence time, oxygen purity, tank geometry and oxygen injection technique. Oxygen generation represents an important operating cost for the Albion Process™. Pivotal to the Albion Process™ operating economically at atmospheric pressure is the capability to efficiently transfer oxygen while utilising as much oxygen injected to the process as possible. To respond to this Glencore Technology developed the HyperSpargeTM supersonic gas injector. This paper compares the HyperSparge™ against other sparging techniques to quantify the benefits of oxygen injection via a supersonic gas jet on scale up of the oxygen mass transfer system. The paper then examines plant survey data from the GPM Gold Project to demonstrate the very high oxygen utilisation that can be achieved with a correctly designed oxygen mass transfer system.INTRODUCTION One of the main challenges in chemical reactor design is the scale-up of processes from the laboratory to industrial scale. Processes which cannot be faithfully simulated with an experiment at the laboratory scale face challenges due to the physical dimensions and complexity of full scale operation. One example of this is the design of oxygen mass transfer systems in atmospheric oxidative leaching circuits such as the Albion Process™. A number of constraints associated with the use of laboratory scale equipment to design full scale circuits are involved in gas mass transfer processes in agitated slurries such as the Albion Process. Chiefly, typical laboratory and pilot size equipment lacks the required volume to provide useful design data without relying on empirical correlations: the specific agitator power input is artificially high, the bubble residence time in the vessel is artificially low, the oxygen partial pressure at the base of the vessel is artificially low and the oxygen delivery method may differ significantly to the industrial process. Further, the dynamic nature of the process introduces additional impacts on gas mass transfer, including the presence of solids, recycle streams and minor elements, plus the variances within the reality of a process plant such as disruptions or variance of feed quality."

Jan 1, 2017

By L. Vollert

"The application of pneumatically-assisted fluidized bed flotation, specifically the ERIEZ HydroFloatTM technology, has found widespread use in non-sulphide processing (particularly phosphate, potash and coal) for the recovery of coarse particles. In gold processing, centrifugal gravity circuits and flash flotation cells are typically employed for the recovery of coarse and near-size liberated gold which tends to accumulate in recycled grinding streams due to bypass to the classifying cyclone underflow streams owing to the higher specific gravity of these gold particles. Early removal of this gold from the grinding circuits contributes toward the reduction of downstream processing losses as a result of overgrinding and particle shape deformation in the case of flotation processing, longer leach residence times in the case of extractive processing, and surface occlusions in the case of both flotation and extractive processing. Furthermore, recovery to bullion attracts higher payment terms by way of comparison to concentrate sales in the case of copper-gold concentrators. This paper assesses the application of pneumatically assisted fluidized bed flotation for the recovery of coarse liberated gold through the analysis of piloting data generated from the operation of a continuously operated 16 inch ERIEZ HydroFloatTM unit treating a sized coarse grinding circuit stream. The paper presents the stage recovery by size performance of the ERIEZ HydroFloatTM unit together with quantitative gold deportment analysis to demonstrate the efficiency with which gold was recovered during this pilot campaign and then compared to more conventional processing units – centrifugal gravity and conventional flotation.INTRODUCTION Newcrest Mining Limited (NML) has identified that an opportunity exists for improving the recovery of coarse composite particles at its current operations, both as a means for improving overall recovery and as an opportunity for early gangue rejection. As such, Newcrest Mining Limited has taken an interest in the application of pneumatically-assisted, fluidized-bed flotation i.e. ERIEZ HydroFloatTM technology. This interest dates back to 2011 with sighter testwork carried out on their Australian-held ore bodies (Kohmuench et al, 2013). Newcrest continues to assess ERIEZ HydroFloatTM potential for coarse composite recovery and, in the case of the topic of this paper, coarse gold recovery based on examples in the literature which demonstrate the efficiency of this technology in this regard (Carmona Franco et al., (2015); Miller et al., (2016); and Kohmuench et al, 2013)."

Jan 1, 2017

By T. Billotte, G. Tirand, J. Zollinger, V. Robin, B. Rouat, D. Daloz

The grain structure prediction of metallic alloys during a welding process is often an issue. In addition to the welding parameters and the alloy nominal composition and properties, the base metal grain structure and chemical homogeneity also play an important role in the formation of the final microstructure. In this paper intensive characterisation of solidification structure in gas tungsten arc welding of Ni base alloy 600 are described. It is shown that in transverse section of the weld, while the grain structure shows some texture following constrained solidification growth, grain density in the weld is similar or greater than grain density in the heat affected zone. This suggests that simulation of the welding structure needs, in order to be predictive, to take into account : epitaxial growth, secondary nucleation events and 3D growth inside the weld pool.

Jan 1, 2015

By Barry W. Schmitke, J. M. Marino

"Cigar Lake Mining Corporation is presently operating an underground test mine in northern Saskatchewan, with a view to developing a high grade uranium deposit. The mining test is intended to demonstrate that the innovative mining methods designed are safe and economical. Two vertical mining methods are considered for the test:• box hole boring from the lower level;• blind boring from the upper level.In both cases, it is anticipated to freeze the ground before excavation to ensure hole stability and limit the inflow of water. Special care will be taken to minimize radiation exposure of personnel.Remote controlled equipment will be used where applicable.The access to the orebody was an important component of the test. After shaft sinking to a depth of 500 m, development work commenced at the 420 level in fractured sandstone which was grouted to restrict the inflow of formation water. The drifting continued in a section of poorly consolidated sand, clay and sandstone; this area was frozen to allow stabilization prior to excavation. At the 480 level relatively little water was encountered in the altered basement gneiss and grouting was not necessary; however, extensive ground support was required in the soft ground areas."

Jan 1, 1992

By L. Paulino, R. A. Camilli, J. Yamamoto, J. C. Araujo

The first paper presented on this work [1], showed how bath ratio was increased from 78% to over 95% using a structured approach to reduce bath chemistry variability. This update will illustrate the steps taken and update the results presented earlier, showing the effects of long power interruptions and several load reductions as well as load increase during the period from 1999 to 2005. Current efficiency was affected by such processes upset; however, bath ratio in range (±0.05) is still higher than 90%, even after an increment of more than 6 kA. This review will explain each of the steps taken to reach stability in this critical smelting parameter.

Jan 1, 2006

By S. S. Burns

"AbstractShovels of 18 cubic yard capacity and larger are described which incorporate advanced technology and techniques providing performance and operation tailored to meet the needs of open-pit mining.To achieve the goal s of increased production at lower cost with consideration of maximum availability, lower energy consumption per ton and low •impact on pit power, Harnischfeger Corporation developed a solid -state drive system (""Electrotorque"" - P&H trademark) and applied unique transmission methods.To date, more than 250,000 hours of experience in different parts of the world under varying operating and environmental conditions has proven that the ""Electrotorque"" shovel is the shovel of the future, today.This paper will discuss the electrical features and touch briefly on some mechanical features.Introduction to ""Electrotorque""THE hoist, crowd, propel and swing machinery of an electric mining shovel are driven by direct-current motors.A D.C. motor is used instead of an A.C. motor because the torque output per ampere input is at a maximum and the fact that it is doubly-fed (armature and field ) provides optimum flexibility in control.The power that is available in the pit is alternating current power. It is therefore necessary to change or convert this A.C. power to D.C. power so that the D.C. motors can be used."

Jan 1, 1977

By Richard Howie

Avian Diversity ?? Pre-mining ?? 110 - 125 species would have occurred ?? Dominated by forest species ?? Wetland productivity unknown ?? Post mining ?? 192 documented ?? Forested species in reduced numbers ?? Increase in wetland species ?? Increase in open country/grassland species

May 1, 2008

By Geo. E. Cole

A GREAT deal of time and energy is now being devoted to the study of post-war reconstruction and rehabilitation, in spite of the fact that as yet we have not won the war in which we are presently engaged. If you feel that the study of post-war problems takes our thought away from the problem immediately before us, you may well query, "Well! What has all that to do with winning the war, our most urgent problem today?" The answer has been given by Principal James of McGill University, Chairman of the Cabinet Committee on Reconstruction: "Reconstruction is something which must be thought of in advance, partly for the purpose of recognizing exactly the influence of war-time activities, controls, and regulations on the post-war Canadian scene. Many people are acutely interested in this great problem. It is not that they are not interested in the war itself, or epochal events that are taking place from day to day. They have a vision of that future which they hope will be Canada's, and this vision inspires them to even greater efforts at the present time". The trend of events would indicate that changes, economic and industrial, after this war will be greatly out of line with those that followed previous wars in history, for the present struggle has involved every nation in the world. In the peace that will come, every engineer will have a task in bringing the most desirable order out of the most distressing chaos. We certainly are living in a changing world; we are witnessing geo-graphical and economic readjustments that no other generation in world's history has ever witnessed. And there is an opinion gaining strength in our Dominion, as in other lands, that after this war we shall live in a world in which our process of thinking and our very way of life will have to undergo drastic changes to cope with the new order of things. Sadly our world of today has had to revise the sublime vision that nation shall not lift up sword against nation, while salvage operations continue to beat ploughshares into tanks and the peaceful pruning-hook into a weapon for the deviltry of the commando.

Jan 1, 1943

By P. Lausch, Z. X. He, J. F. Archibald

"Documented underground fill failures have resulted because of the lack of adequate knowledge concerning fill strength and other physical parameters, as well as to a lack of consistent quality of fill materials being used by operators. On the basis of literature review and correspondence with backfill operators at 18 mines throughout the province of Ontario, non-systematic quality control procedures have been shown to exist, both within different levels of single operations and between separate mining operations, which act to provide inferior engineered fill materials and erratic application response in situ.Assessment of existing procedures set by mine operators for determining backfill physical parameters, and recommendation of optimum fill material testing and manufacturing guidelines are presented in this paper.A series of standard fill characterization test procedures are recommended to provide substantial, though not comprehensive, fill behaviour review. The purpose of these recommendations is to propose industry standards for backfill quality review. Data acquired could be utilized for fill design functions and as a means of comparing fill quality parameters between sites in a regular and more systematic fashion than is presently done."

Jan 1, 1993

"5.1. IntroductionThe sample preparation requirements for bulk analyses of platinum-group elements (PGE) are different from the requirements for ore microscopy and in-situ analyses. It is necessary that the initial sample collection results in as representative a sample as possible for both types of analyses. Ingamells (1980) believes, however, that sampling is always imperfect and that there is no such thing as a truly representative sample. Once collected, the usual low content and irregularly dispersed nature of the PGE require that samples for bulk analyses be made as uniform as possible, whereas in samples for ore microscopy and in-situ analyses the PGE must be concentrated. Because of the generally high specific gravity of platinum-group minerals (PGM), certain precautions must be taken, such as mixing the sample material in the bags prior to opening.5.2. Preparation forBulk Analytical MethodsThe principal factors that determine the size of the sample required for a bulk analysis are grade, heterogeneity and grainsize. Initially, the grade and sample heterogeneity can only be estimated and a sampling methodology is developed with experience. It is essential at all times, however, that the assayers have information about the source of the sample and the purpose for the analysis. Information on the grain-size, which can only be obtained through mineralogical analysis, is also very important for PGE analyses, but, unfortunately, is often ignored.5.2.1. Samples fromUnconsolidated DepositsConcentrations of PGE may occur in eluvial deposits as well as in a large variety of alluvial deposits, including those of fluvial and glaciofluvial origin. These deposits are often difficult to map and sampling is further complicated by the wide range, from sand-size to boulders, of the non-POE-bearing constituents, and by the irregular distribution and shape of the ""pay streaks"". PGE concentrations in unconsolidated deposits are largely composed of resistant Pt-Fe and Os-Ir-Ru alloys (cf. Cabri and Harris, 1975 and Raicevic and Cabri, 1976), thus making comminution to the usual-150 to -200 mesh somewhat unreliable, due to the malleability of these alloys."

Jan 1, 1979

By Erik Q. Dahl

The strength of green and sintered pellets during reduction under various conditions in a laboratory kiln has been investigated. Equipment and test methods are described, together with the results obtained. The strength of sintered pellets drops sharply when the reduction starts, and goes through a minimum at the 70 per cent oxidation level. At more advanced reduction, the strength increases with increasing metallization. Successful use of green pellets as kiln feed requires that more attention be paid to the pellet preparation than is necessary when producing pellets for separate sintering. In particular, the ores have to be ground to a greater fineness. The initial strength of green pellets is low. Below the 70 per cent oxidation level, however, the strength of these pellets is about the same as the strength of sintered ones. Additions of such materials as silica, limestone and anthracite coal; within reasonable limits, affect the strength only slightly.

Jan 1, 1966

By B. R. Richards, B. G. W. Robinson

"This paper shows how metal values can be profitably won from a comparatively small and remotely located but high-grade orebody. To do so is not uractical for a large mining company, with its necessarily high overhead of services and organization essential to a large producer.To evaluate, develop and profitably exploit a limited but defined ore deposit becomes only a problem of determining the dollars required to win the dollars available. This paper will record how this was carried out during 1965 and at the same time describe the history, development and production plant of this property."

Jan 1, 1966

By Tong Gao, Jingyu Qin, Xiangfa Liu, Zengqiang Li, Yaoxian Zhang

"The recycling of aluminum materials is a green industry while Al–Si–Fe is a typical scrap aluminum alloy. The key point of recycling Al–Si–Fe alloys is to separate Al and Fe. A method by introducing Al–Si–Fe alloy into Mg melt has been investigated in this work. A separation layer with gathered Fe–rich and Al–poor Fe3Al0.7Si0.3particleswereobtained at the bottom of the cooled ingot, indicating that ß–Al5FeSi phase evolves to Fe3Al0.7Si0.3,and quantities of Al are released to the upper Mg matrix simultaneously. However, the evolution of Al3Fe by adding binary Al–Fe alloy into Mg melt is different. It is supposed that element Si plays an important role in the phase evolution procedure, thus affects the performance of this method.INTRODUCTIONThe rapid development of aeronautic, automotive and aerospace technologies strongly depends on the consumption of materials while sustainable development is the future direction. Aluminum is a recyclable material and Fe is one of the most common impurities. Fe can be introduced into Al alloys by adding low–purity alloying materials and by using unprotected ferrous crucible, tools, or equipment (Belov, Eskin, & Avxentieva, 2005; Lu& Dahle, 2005).For instance, wear–resistant rings are usually inserted into piston head when producing Al–Si pistons and an infiltration procedure by putting the cast iron rings into Al melt before casting is always essential. As a result, both the re–melting of pistons and the reuse of Al melt for infiltrating rings lead to the enrichment of Fe element, which can be even high to5 wt.%(Viala, Peronnet, Barbeau, Bosselet, & Bouix, 2002).It is widely known that coarse ß–Al5FeSi particles will form in high Fe–contained Al–Si–Fe alloys which is harmful for the mechanical properties. In the past decades, several methods to eliminate the harmful effect of ß–Al5FeSi have been investigated which can be widely referred (Munson, 1967; Lee, Kawamura, Inoue, Cho, & Masumoto, 1997; Suárez–Peña& Asensio–Lozano, 2006; Eidhed, 2008).These methods can be divided into two kinds. One is to aggregate and remove the Fe–rich phase through the methods of centrifugation, gravity filtration or magnetic separation. The other way is modifing the morphology of flake–like ß–Al5FeSi by overheating the melt or adding neutralized elements. However, these traditional methods are rarely used due to respective disadvantages, while the commonly used method in industries is using primary aluminum for dilution. However, only less than 30wt.% of scrap Al can be added into primary Al melt for each melting work while it also results in the decrease of product quality simultaneously(Zhang, Liu, & Liu, 2016)."

Jan 1, 2018

By J. E. Udd, L. B. Geller

"Mine-shaft wire-rope discard regulations include, among other criteria, a limited amount of permissible loss-of-breaking-strength (LBS). Currently, this parameter is estimated on the basis of non-destrutive-testing (NDT) with electro-magnetic (EM) type instruments. This paper analyses the accuracy with which these estimates have, so far, been obtained in practice.It concludes that while certain types of testers have produced better results than others, the desired accuracy level has not been attained. Also discussed are the putative reasons for this situation, and appropriate actions that the mining industry might wish to take."

Jan 1, 1990

By T. V. Simpkinson

Abstract A brief history of the electric arc furnace process of steel-making is given. The greater relative importance of this method of steel manufacture to the Canadian steel industry, as compared with its importance in the steel industry of the United States, is shown. The scope of the process is outlined and brief mention is made of the difficulty of obtaining melting stock low in alloy content. The physical chemistry of steel-making is discussed at length in simple terms, with emphasis on oxidation, de-oxidation, and the role of hydrogen. Carbide-type and silicon-type slags are described and the particular usefulness of each is outlined. The importance of various factors in the melting practice is evaluated on the basis of practical experience. Introduction Although electric furnace steels constitute only a small portion of the total weight of steel used in industrial operations, their importance is relatively much greater than is indicated by comparative tonnage figures. Tool steels, which are vital to all industry, are made almost exclusively by the basic electric arc furnace process, as are stainless steels, valve steels, and the higher alloy types of the class usually referred to as "alloy steels'. For many applications where steel other than electric furnace quality is often used, and when first cost is secondary to performance in service, the extra steel cost of electric furnace quality material is usually returned with interest by consistently longer service life. The electric furnace is pre-eminent in the quality alloy steel field because of the control that may be exercised over conditions of oxidation, de-oxidation, and temperature, the fundamental operations in steel making.

Jan 1, 1948

By W. G. Dallas

The social and environmental problems presented by the location of a large zinc/ lead ore body within one mile of a thriving town are described. The development problems are social, involving the education of the in habitants , and environmental, requiring the development of a planning strategy and the evolution of a baseline and post -operational monitoring system. The necessity for an environmental-impact assessment and a thorough baseline study is emphasized. The continuing psycho-social consideration of community reaction is advocated.

Jan 1, 1977

By A. C. Hitchins, C. N. Orssich

The Eagle zone is a gold-bearing, sheeted, quartz vein porphyry deposit hosted by the Cretaceous Dublin Gulch biotite granodiorite stock, located in central Yukon, 50 km north of Mayo. The deposit occurs at the western end of the stock and has been drill tested over a 1000 m by 500 m area, to a depth of 150m. Mineralization consists of 1 cm to 2 Cm wide, parallel, grey and white quartz veins with accessory gold, arsenopyrite, pyrite, pyrrhotite, chalcopyrite, native bismuth, bismuthinite, and scheelite. Vein densities range from two to fifteen veins per metre and average approximately five per metre. The majority of the veins have potassic and or phyllic alteration envelopes. Alteration of the granodiorite becomes pervasive as vein densities increase. Mineralization outside of the Eagle zone, but spatially related to the Dublin Gulch stock, includes: (i) scheelite bearing sheeted quartz vein zones within the east-central portion of the stock; (ii) a swarm of gold-bearing quartz-sulphide veins up to a metre wide in a zone along the northern contact of the stock and extending 7 km further west; (iii) the Mar scheelite skarn located on the south side of the stock; and (iv) cassiterite-bearing breccias located 2 km north of the stock. A geological potential resource of 64.5 Mt tonnes at a grade of 1.03 g/t Au has been estimated for the Eagle zone from widely spaced core and reverse circulation drill holes. Mineralization is open at depth, on strike to the west and beneath the hornfels to the north.

Jan 1, 1995

By Hiwa Salimi, Foley. Stephen R, Loghman Moradi

Common water-miscible organic solvents including DMSO, DMF, methanol, ethanol, acetone and THF in combination with HCl and low concentrations of H2O2 were investigated for dissolution of gold. THF showed the best result demonstrating that gold powder could be completely dissolved in 1.5 hours in 1.0 mol/L HCl and 0.2 mol/L H2O2. No complete gold dissolution was observed for the rest of solvents even after 24 hours. The rate of gold dissolution was measured by dissolving gold wire in THF/HCl/H2O2 mixture. The rate of gold dissolution in optimised condition was 75 g m-2 h-1 at room temperature and significantly increased to 590 g m-2 h-1 by raising the temperature up to 60 oC. Although a THF/HCl/H2O2 mixture showed a slower dissolution rate in comparison with aqua regia, however the applied conditions are considerably milder which is highly promising for gold leaching in an industrial scale.

Jan 1, 2015

By Eduardo R. Rodrigues, Ankur Narang, Roberto Federico Ausas, U. T. Mello, Jose Maria Segura Serra, M. R. Lakshmikantha, Ignacio Carol, Kamal C. Das

"Modeling of big faults or weak planes of strong and weak discontinuities is of major importance to assess the Geomechanical behaviour of mining/civil tunnel, reservoirs etc. For modelling fractures in Geomechanics, prior art has been limited to Interface Elements which suffer from numerical instability and where faults are required to be aligned with element edges. In this paper, we consider comparative study on finite elements for capturing strong discontinuities by means of elemental (EFEM) and nodal enrichments (XFEM) for Geomechanical applications. For general fracture scenarios, Oliver et al. (2008) have demonstrated advantages of EFEM over XFEM for including: (a) ease of modeling in any standard finite element code due to the possibility of static condensation, (b) higher accuracy in some cases for coarse meshes, and, (c) a reduced computational cost. However, there has been no work that considers cohesive fractures in Geomechanics. We present a numerical analysis based on a linear constitutive model and linear triangular elements for the bulk and a linear constitutive behaviour for the fault for a representative set of fault planes in a circular tunnel made in rock mass. In the numerical examples we consider both well-traced and bad-traced meshes. We focus on traction profile analysis for both EFEM and XFEM, since that is crucial to understand the cohesive fracture behaviour specially rock joint. Therefore in each case, shear, normal and stress ratio are compared across the two methods along the fault plane. This is the first such work that compares XFEM and EFEM behaviour for Geomechanics problems.For the considered class of problems and the sharp penalization approach without regularizations adopted, it can be observed that accuracy and robustness of EFEM may strongly depend on the fault orientation with respect to the element edges, while, XFEM is independent of fault alignment with element edges. It has been also observed that, with mesh refinement model, stress oscillation completely removed with XFEM however EFEM fails to provide oscillation free results with finer mesh in case bad-traced model. We also performed error analysis and found that in case of bad-traced mesh the average error in the XFEM is 84% smaller than of EFEM and for XFEM the error goes to zero with increasing mesh resolution, while for EFEM the error increases with mesh resolution. Thus, we experimentally demonstrate that, XFEM performs better than EFEM in terms of accuracy and rate of convergence with marginal increase in computational cost. This work hence provides novel insights on the application of XFEM and EFEM in Geomechanics."

Jan 1, 2015