Search Documents

By E. L. Chanturiya

The research and characterisation for compositional, physicochemical, structural, electrical and flotation properties of various pyrite samples for a copper-zinc sulfide ore was carried out. Various methods were used during the research, such as optical microscopy, X-ray diffraction, electron probe micro-analysis (EPMA), phase emission analysis, routine chemical analysis, auger electron spectroscopy (AES), scanning electron microscopy (SEM), back-scattered electron images (BSE), potentiometry, and instrumental neutron-activation analysis, flotation. Analysis of obtained results established the interrelation between impurity structures and concentration of electric charge carriers in minerals, Butyl xanthate sorption and flotation yield of pyrite. The research concluded that pyrite samples differ by morphology, micro defects of structure, concentration of donor and acceptor impurities (Co, As, Sb, etc.) and conductivity parameters (thermo-electrical force, specific resistance and concentration of charge carriers The peculiarity of pentagon-dodecahedral pyrite is the high concentration of electric charge carriers (electrons) and the more negative surface potential (by 25–75 mV) in comparison to cubic pyrite. The surface of cubic varieties is more active, therefore it is oxidized in alkaline lime medium much faster, than the surface of pentagon-dodecahedral varieties. This phenomenon is caused by high reaction ability, irregular jointing and defects of cubic pyrite. This promotes the increase of calcium ion sorption on its surface and the decrease of Butyl xanthate sorption. According to this, an increase in alkalinity (lime medium) from a pH of 10.0–11.5 leads to an increase of gold content reporting to the tail of bulk flotation. Gold content is increased from 0.58 g/t (?? 9.5) to 1.9 g/t (?? 11.6), which represents an increase in gold recovery of 24.68 to 79%, respectively.

Jan 1, 2016

By D. D. Hogarth

"Edward Haycock, Engineer and Public Contractor Edward Haycock was born in Shrewsbury, England, June 14, 1813. His father was John Haycock, a timber merchant and soap manufacturer, residing at Swan Hill Court, Shrewsbury, and his mother Esther was the daughter of William Hilton of Hempstead, Hertfordshire. Edward's paternal grandfather, John Hiram Haycock, was the first of a line of architects that ""changed the face of Shrewsbury"" and ""provided some of the best examples of typical Victorian architecture in Shropshire""(1). Nothing is known of Edward's early life or education, although it appears that he made no attempt to follow this artistic trend. In 1833, Edward immigrated to Canada. The following year, he married Mary Butler, daughter of Johnson Butler, a Lieutenant-Colonel in the Lincoln Militia during the War of 1812. Mrs. Haycock, as co-heiress of Johnson Butler's estate, was assigned 600 choice acres of farmland in Brooke Township near present-day Sarnia. This alone would have guaranteed a tidy income, but the Haycocks soon disposed of this land, the last lots being sold in May 1840. Instead, Haycock turned his hand to engineering and, for a number of years, was employed by the Great Western Railway first in Woodstock and later in Hamilton. He then moved to Port Hope, tried farming, worked in the engineering office of the Port Hope, Lindsay and Beaverton Railway Company, and later constructed a portion of this railway(2). During his stay in Port Hope, Haycock met his future partners Ralph Jones, a contractor, and Thomas Curtis Clarke, chief engineer with the P.H.L. and B. Railway Company. The alliance was styled Jones, Haycock and Company and their most successful venture was the construction of the Government Buildings in Ottawa. This work was the crowning achievement of Haycock's career and, no doubt, his proudest moment was at 11:30 a.m., April 2, 1860, when his daughter Mary Emily, then a little girl of 4, with a special silver trowel ceremoniously laid the first stone. Of special interest in this project were the quarrying operations, which introduced Haycock to the art and difficulties of mining as well as to the potential returns of mines. Sandstone, for facing, was drawn from four quarries, 10 to 12 miles from the Departmental Buildings. Haycock seems to have been in charge of these operations, which in the early stages involved an average labour force of 86 men and 43 teams. However, by 1861, quarrying had declined in importance and the contractors were able to concentrate whole-heartedly on the construction site."

Jan 1, 1999

By Eric Poulin, Anthony Clapperton, Jocelyn Bouchard, Jaime Cristobal Rojas-Montes, Benjamin Legare

"Several grinding mill dynamic simulators have been developed in the last half-century. However, complete circuit simulations are mainly limited to academic investigations, and on-site applications for advanced control or real-time optimization are scarce. One particular issue that has certainly curbed a more widespread use is the time and efforts required for model calibration. This paper illustrates this challenge and presents a calibration method based on dynamic simulation using industrial data and laboratory testwork. The simulator models discussed originate from the work of Austin and Luckie (1972) for grinding mills, and Plitt (1976) for hydrocyclones. A two-stage approach based on a least squares minimization allows determining calibration parameters values. Firstly, laboratory testwork are required for characterizing breakage coefficients of the ore. Secondly, step change responses and their simulation— effect of ore and water feed rates on output flow rates and size distributions—allows identifying transport/mixing conditions. Simulation results are in agreement with actual process responses to variations of feed conditions obtained from a plant survey.INTRODUCTIONDynamic models for grinding circuits has been intensively studied since the 1970's notably by Austin and Luckie (1972b), Klimpel and Austin (1984), Rogovin and Hogg (1988), Napier-Munn et al. (1996), Liu and Spencer (2004), and King (2012) among others. The resulting models primarily serve in simulation applications for process equipment sizing, which incidentally also helps developing a better understanding of comminution operations. An obstacle curbing a more widespread and targeted use of grinding simulation for process control and optimization purposes is the time and efforts required for dynamic model calibration. It remains a cumbersome task that is typically not well detailed in technical papers. This could explain why dynamic process simulators are mainly confined to academic applications."

Jan 1, 2016

By Shuan-cheng Gu

Roof bed separation often occurred due to the deformation incoordination of surrounding rock following the excavation of mine roadway. Bed separation has effect on the bolts, and the estimation of the influence will directly affect the safety of support systems. In this paper, the hyperbolic function model to analyze the load transfer mechanism on the bolts was simplified as the exponential function form for easy calculation. An elastic-plastic analysis model of the bolt loading occurred by the bed separation was established. And the development low that the bed separation affected to the bolt loading was discussed. According to the parameters analysis of different separation values and locations, the influence law of the bolt loading caused by roof bed separation was summarized. Finally, the effects of bed separation were considered for the bolting design, it was able to provide a reference to the anchorage design of stratified rock.

Aug 1, 2013

By Jean-Luc Beaudoin

"In addition to the actual energy consumed, billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays. The principles of a power factor regulator, the two ways of improving the power factor and methods for calculating the capacitor values required will be described.The rate structure of the utility company is founded on three cornerstones: the energy consumed during a given period of time and two penalties imposed when the power factor is low or the power demand is high. Even though the normal consumption of a customer might be 10 kW, with a peak demand of 20 kW only once a month, the wiring and associated equipment at the input to the customer's plant will have to accommodate this peak demand. The power company has no means of forecasting these demands and cannot therefore provide the additional equipment necessary. So it exacts a penalty, and the customer must take all possible steps to avoid these peak power demands. This can be accomplished by using an automatic peak load regulator which will selectively disconnect the loads which are not essential in the operation of a plant .The principles of such a controller will be described.Principles of power factor regulatorsThe operating principles of a power factor regulator will now be described. It might be asked why the power factor of an electrical installation in a mine, or a factory, should be corrected at all, but there is a simple answer. In addition to the actual energy consumed, the billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays."

Jan 1, 1982

By Richard Simon

This paper presents an ongoing study on the use of borehole breakouts to estimate in situ stresses at depth in a Canadian underground mine. Breakouts were identified using an acoustic televiewer (ATV) probe. Rock samples were tested in a laboratory to determine their failure curve. Breakout analyses were performed using a 2D failure criterion and a multiaxial failure criterion. Analyses were carried out using both short-term (peak) and long-term strengths (the latter considered here as being represented by the damage initiation threshold DIT). The analyses have shown that the use of the longterm strength and a multiaxial failure criterion leads to results that are more consistent with stress measurements performed in the field, in the vicinity of the mine.

Jun 1, 2012

By M. Nejati, A. Paluszny, R. W. Zimmerman

A numerical method is proposed to propagate multiple discrete fractures leading to primary fragmentation in a mine that is being worked using block caving. Deformation is computed using the finite element method, fractures are represented explicitly, and the mine domain is discretized by an unstructured mesh. Bedding planes are represented by systematically varying the elastic modulus of the rock and by defining horizontal weakness planes. Fractures and matrix are represented using parametric surfaces, and tips are defined by their boundary curves. Tip advance is controlled by a failure criterion, and a criterion for propagation direction and magnitude, based on the evaluation of the modal stress intensity factors. A novel domain integral approach is applied to accurately compute stress intensity factors (K) ahead of fracture tips in three dimensions. The method does not require a structured volumetric mesh structure around the crack tip, as integration is performed over a series of virtual surface domains along the crack front. The method is efficient, as it makes direct use of automatically generated, arbitrary tetrahedral meshes, and approximates stress intensity factors (KI, KII, KIII) along each crack front using Interaction-integrals. As opposed to the JIntegral, the method does not decompose K a-posteriori, but instead uses an auxiliary field to directly compute modal K. When using this method, numerical approximations of K do not exhibit dependence on the mesh layout, and require meshes that can generally be ten times coarser than are required by displacement- and stress-based methods. Volumetric meshing requires only, on average, 17% of each computation step. Thus, cracks do not follow any pre-existing mesh structure, and the method is well suited for high-density fracture datasets. The method is demonstrated for primary fragmentation of a mine area covering 110 initial draw points, immediately beneath a 2m high undercut. Displacement is constrained at all boundaries except the surface of the undercut. The growth of the fractures is investigated at the onset of the undercut. Ninety initial disc-shaped fractures are taken into account, each having an initial radius of 10 m. Fractures grow around the undercut, intersect the bedding plane boundaries, and the domain is fragmented as a result.

Jan 1, 2015

By E. W. Garner

THE greatest problem confronting business managers in modern times is not production, but distribution. It would be easy to expand productive output, but it is difficult to find markets for all that is produced. The fundamental source of economic difficulty, in the view of many observers, is a lack of proper balance between productive capacity and consumptive capacity. The studies conducted by the Brookings Institution on the general subject, "The Distribution of Income in Relation to Economic Progress", have led to conclusions of far-reaching significance, which may be summarized briefly as follows: (1) We have never lived beyond our economic means or capacity. (2) We have not been suffering from general overproduction. (3) We have not as yet reached a stage in our economic evolution at which it is possible to provide adequate standards of living for everybody. ( 4) It would require less than a 25 per cent increase in purchasing power among the masses to absorb our full productive capacity. (5) Production-curtailment programmes-whatever their merit in meeting temporary maladjustments-can only lead to national impoverishment. (6) Our inability to find markets adequate to absorb the full output of our productive establishments is explained by the unequal distribution of income and consequent restricted flow of purchasing power through consumptive channels. (7) The slow rate of growth of consumptive demand serves to retard the rate at which new capital is constructed, and hence the rate of economic progress. (8) The primary need is a rapidly expanding total income, and a broader diffusion of this income among the masses of the people. (9) A broader diffusion of income can best be achieved by reducing prices as rapidly as increasing efficiency will permit. That is to say, the benefits of technological progress, mass production, and low unit costs must be promptly passed on to consumers in the form of lower prices-giving more for each dollar.

Jan 1, 1936

By Rachel S. Prudhomme, Michael L. Jeremic

"The consolidation of mine backfill by free zing is a concept which has been under study in the mining engineering laboratories at Laurentian University during the past three years. The proposed underground application of freezing involves the artificial freezing of in-situ backfill by means of a refrigerated brine solution which would be circulated through a circuit off freeze pipes. The most interesting findings to date are: (I) The uniaxial compressive strength off frozen fill is considerably higher than that of cemented fill in a ratio of 20:1 (aggregate to cement), and (2) load deformation characteristics of the frozen fill suggest that a higher ice content results in more brittle failure and that samples which have initially failed can still support up 10 one-half the ultimate load without additional failure.Although at this early stage a derailed economic analysis of the procedure has not been possible, a general evaluation of the costs involved suggests that the method could be competitive with the hydraulic placement of cemented backfill. Results obtained from laboratory investigations indicate that the freezing of backfill is a structurally feasible option .IntroductionGround consolidation by freezing is based on the principle of transformation o f water contained in an aggregate-slurry into ice, which act s as a binding agent between the bulk particles, and which results in the transformation of a granular soil into a ""rock -type"" material. The abrasive nature of the particles enhance s the strength o f the ice by providing internal friction. As a result of this internal friction, the chances of plastic flow of the frozen mass when in a loaded condition are reduced(1). T he strength of a frozen aggregate is al so dependent on the grain shape of the aggregate particles which may or may not promote particle interlocking(2) and on the temperature since, below the freezing point of the water/aggregate mixture, the strength of the frozen mass increase s with decreasing temperatures.In the shaft sinking industry, artificial freezing of loose , unconsolidated soils has been in practice for several decades. Shafts for Saskatchewan 's potash industry have been sun k to depths of 3000 feet by employing artificial freezing to stabilize the Blairmore Formation(3). The common procedure for freezing ground for shaft sinking is summarized as follows(4,5): I) 150 mm diameter bore holes spaced on 1.5 m centres are drilled in a circular pattern with a radius of 1.5 m outside the periphery of the proposed shaft."

Jan 1, 1985

By Real Daigneault, François Robert, J. Paul Golightly, Jean-Yves Cloutier, Jayanta Guha, Pierre Pilote

"The Casa-Berardi East, Center and West deposits, located in the Archean Abitibi, Sub province, are hosted by volcanic and sedimentary units of varying compositions, less than300 m from the Casa-Berardi fault (CBF). The CBF, a brittle structure, represents an increment in the structural evolution of a regional-scale deformation zone showing ductile-brittle behavior known as the Casa-Berardi deformation zone (CBDZ). The CBDZ is characterized by a mylonitic Sc1 foliation which is folded a.n4 deformed by a later sczfoliation in high strain zones.Four generations of quartz vein and fracture systems have been recognized within the Casa-Berardi deposits. Most economic gold mineralization, occurring in the second generation system, is found within high strain zones. This system hosts three types of mineralized structures: (1) banded quartz veins; (2) swarms of veins and mineralized host rocks; and (3) disseminated sulphides along fractures. An early carbonate hydrothermal alteration zone (pre- to syntectonic) surrounds the deposits. Alteration associated with gold mineralization is contemporaneous to late ( syn- to post-tectonic) relative to the development of progressive deformation in the CBDZ. The geological characteristics and paragenesis of the four quartz vein and fracture systems developed as an integral part of the geodynamic evolution of the Casa-Berardi deformation zone."

Jan 1, 1990

By G. P. Kundargi

India is one of the fastest growing economies in the world. The role of the Iron & Steel industry is very important for the development of the country. Iron and steel are among the most important components required for the infrastructure development of the country. This is one of the fastest growing sectors. The demand drivers for the Indian Iron & Steel industry are increase in the activities of the manufacturing industry and infrastructure development. Indian Iron & Steel industry with its strong forward and backward linkages contributes significantly to overall growth and development of the economy. The industry today directly contributes 2% of India?s Gross Domestic Product and its weightage in the official Index of Industrial Production (IIP) is 6.2%. Manganese is a main ingredient for production of steel. Almost 90% manganese is being utilized by the steel industry worldwide. Globally, there is no substitute for manganese as on date. There is huge gap between demand and production of manganese ore in the country. To meet this demand gap and to support for growth of national economy, MOIL Limited (formerly Manganese Ore India Limited), a Government Enterprises, producing annually around 1.1 million tonnes (mt) of manganese ore and value added products, has geared up with various infrastructural activities to increase the present production capacity of 1.1?1.5 mt in 2016?2017 and 2.2 mt in 2020?2021. The paper deals with the technological improvements and infrastructural development activities of MOIL; this will help MOIL to become the market leader in manganese ore production globally in the coming years.

Aug 1, 2013

By P. Zhang, K. Liu, L. Ou

"The strength and mechanism of Portland cement prepared from stone coal vanadium slag were studied in this paper. Initially, the slag was used as silicon raw materials to prepare clinker. By blending the prepared clinker with gypsum, waste, and fly ash, a series of different grades cement got well prepared. All of performances of the cement were up to the requirements of China’s national standard. The hydration products and microstructure of cement were identified and analyzed by X-ray diffraction and scanning electron microscopy. With the comparison of cement hydration characteristics at different ages, the strength formation mechanism of cement was clarified. The experimental results suggested that adding the fine materials (mainly waste and fly ash) to replace part of clinker would accelerate cement hydration, as it provided additional surfaces for the nucleation and growth of hydration products. And the hydration products were similar to ordinary Portland cement, mainly containing the amorphous calcium silicate hydrates (C-S-H), acicular ettringite (AFt) and portlandite (CH). With hydration time increasing, the hydration products continuously covered the cement particles, resulting in a thicker surface layer. As a result, it gradually condensed into a dense structure block with small pores and smooth surfaces, which led to higher strength. In conclusion, using the vanadium slag to prepare Portland cement can realize the utilization of solid mineral wastes, which will bring huge ecological and economic benefits.INTRODUCTIONWith the development of China’s mining industry, more and more mineral waste residue is discharged every year. These solid wastes cause varieties of resources and environmental problems on people’s living area. While at the same time, the demands of cement are increasing with the remarkable development of the construction industry. Thus, in recent years, utilization of proper solid waste to prepare cement has become an efficient way to deal with the solid mineral wastes problems (Boncukcuoglu, Kocakeri?M, & Tosunoglu, 2002; Simatupang, Hanafi, Purwasasmita, Imran, & Pane, 2012; Tsakiridis, Papadimitriou, Tsivilis, & Koroneos, 2008; Yun, Yong, Choi, Lee, & Lachemi, 2009)."

Jan 1, 2016

By Oleg G. Tovmachenko

We have studied optical properties of fluorescent nanoparticles. These particles consist of a metal (gold/silver) core, an empty and a dye labelled silica shells. The different dye molecules with moderate quantum yields (about 0.3) has been used. Almost all of types of nanoparticles show fluorescence enhancement. This enhancement is strongly dependent on the degree of the overlap between the surface plasmon band of the metal and the absorption/emission band of the dye molecules. The results are interpreted in terms of competition between local field enhancement and quenching of fluorescence by the metal surface.

Oct 1, 2003

By C. R. Edwards

"Equity Silver Mines Limited owns and operates an open pit silver 111ine located 37 km southeast of Houston in the Omineca District of British Columbia, Figure l. The property is approximately 300 km west of Prince George and 417 km east of the Port of Prince Rupert. This is the largest silver mine in Canada and one of the five largest silver producers in the western world.Equity is a subsidiary of Placer Development Limited, which owns 70 of Equity's issued and outstanding Common Shares. Placer was responsible for financing and developing the property and now provides general management and administrative services.All mining is by open pit methods, using three 1600 P&H shovels, eight 45 t Caterpillar and three 77 t Wabco trucks, three 40R rotary drills, two D8 dozers, one 9888 front-end loader and other ancillary equipment. We are now phasing out the Southern Tail pit and bringing the Main Zone into productior; see Figure 2.Comminution in the concentrator is achieved via primary, secondary, and tertiary crushers followed by rod and ball mills. The flotation circuit, with Southern Tail ore, produces a concentrate containing between 3 000 and 6 500 g of silver per tonne, 201 copper, and 25 g of gold per tonne. Running Main Zone ore, concentrate grades will decrease to about 4 500 g of silver per tonne, 17% copper, and 18 g of gold per tonne. Design milling capacity is 5 300 tpd, which is often exceeded.The flotation concentrate contains relatively high levels of antimony and arsenic. Because of these impurities Equity was unable to obtain economically acceptable long-term sales contracts for flotation concentrate. For this reason a leaching process was developed, and a plant designed, built and placed in operation. Due to the complex and unique technology involved, many start-up problems were encountered but by March 1983 the leach plant was considered ""fully operational."" This paper describes some of our progress and problems in bringing the Equity leach plant through its start-up period."

Jan 1, 1984

By R. P. Townsend

It is a widely accepted "fact" that a Koepe friction hoist is generally the best solution for production hoisting when compared to a double drum hoists. This would appear to be true if one looks at the initial capital cost of just the hoist, and also if one compares the size of the motors selected for the duty. But is this the whole story? What are the longer term costs involved in the hoist's operation, and what are the relative efficiency's of the two designs? Perhaps the Koepe hoist design enjoys a better reputation than it deserves.

Jan 1, 2011

By A. Galibois, H. Monette, J. L. Collins

This paper deals with the problem of caving, which occurs in varying degrees in blast holes before loading. It is shown that the distribution of the amount of caving in materials may be described by a gamma density function. A decision model to determine the optimal depth of over-drilling 'in order to minimize the expected additional cost per hole is described. Two different policies are discussed. In addition, charts which permit the mine operator to realize significant savings have been drawn for different actual situations.

Jan 1, 1971

By François Baillargeon

Two types of ore deposit provide the bulk of the world nickel production. They are the hypogene magmatic massive sulfide deposits and the supergene lateritic deposits. Platinum group elements (PGE) are also extracted from magmatic sulfide deposits. Recent sky-rocketing price of palladium has prompted the mineral industry to seek alternative resources. In such a manner has emerged the Lac-des-Iles type of target, a very low sulfide-bearing bulk tonnage type of deposit. Furthermore, unconventional (e.g. non-magmatic) types of deposit are now sought more intensively (Wilde et al., 2003). Considering both this trend of the PGE Industry, and that only a few magmatic deposits account significantly for the world nickel production, someone may wonder if a diversification of the hypogene nickel resources base would not be needed in the near future. Laterites are residual deposits developed on ultramafic rock under wet tropical climate. Are all ultramafic protoliths equal to generate high-grade lateritic deposit? Are some preweathering processes important to generate favourable ultramafic protoliths? The mineralogical heterogeneity of some ?dry? lateritic nickel deposits renders their ore beneficiation difficult. Is the type of nickel-bearing mineral found in the protolith a significant factor influencing the laterite heterogeneity? To contribute to answer all these questions, we have undertaken a research project on the nickel occurrences of the southern Quebec serpentinite belts. Why choosing this specific region for such a project? First because, due to continuous mining of asbestos ore since 1870, the serpentinite belts of this region are among the best exposed and studied in the world. Secondly, this region host a complete spectrum of nickel deposits that have been described before in the scientific literature. Furthermore, this region is slightly to moderately metamorphosed which make it perfectly suited to study the departure from magmatic nickeliferous paragenesis through various metamorphic conditions. As a matter of fact two orogenic events affected this region, the Taconian, in Ordovician time, and the Acadian during the Devonian. The magnitude and the timing of these dynamo-metamorphic events vary considerably through the region (Gauthier et al., 1994). These variations are now well constrained due to precise age dating.

May 1, 2003

Accurate hematite solubility data are required to construct predictive solution chemistry models for complex hydrometallurgical solutions. These data are useful in understanding Fe(III) speciation and precipitation in a variety of hydrometallurgical processes. Hematite solubility data were generated in 10 to 70 g/L H2SO4 solutions and at temperatures from 130 to 270°C, using specially modified titanium autoclaves. These measurements represent an improvement over previous experimental data because of better in-situ filtration of the sample aliquots, the approach to equilibrium via hematite dissolution, and the inhibition of Fe(III) reduction on titanium surfaces. Fe(III) reduction was particularly studied to evaluate the inflationary effect of Fe(II) on hematite solubility measurements. Chromate was found to reliably inhibit Fe(III) reduction on titanium. Finally, the generated hematite solubility data were used to construct a solution chemistry model using the OLI software.

Jan 1, 2006

By O'Halloran. Gerard F.

"ECSTALL MINING has installed in their plants the most modern equipment in the mining industry. At the minesite, digital blocked frequency controls are used to monitor all crushers, conveyors, ventilation equipment and pumps from underground. Distant pumping stations are monitored and controlled by radio. Modern friction skip and cage hoisting systems have been installed with static power supply designed for automatic operation. Rotary-type compressors of recent design are in service in place of the conventional reciprocating-type units. At the concentrator, the 800- and 1500-hp synchronous motors driving the grinding mills have static field excitation and pneumatic clutches, still meeting modern-day concepts, having been• installed in 1966. The maintenance work load has increased annually for the past eight years. The modern plant, with all the present-day sophistication, must have a welltrained and well-organized force of skilled workers, and a maintenance system which will supply realistic facts and guidelines. This presentation will review the relative location of plants, utilities, maintenance and services, plant maintenance control and mechanical control. It is the hope that enough information will be presented to weigh the size of the job and how the resources are utilized for controlled maintenance."

Jan 1, 1974

By E. M. Stiles

Introduction The papers that follow deal with recently completed major improvements in practices at the Sullivan operations in Kimberley. The papers have been prepared by members of the Consolidated Engineering Staff and outline the construction programme which has been in progress for the past three years, entailing an expenditure of some millions of dollars. Four major operational changes have been brought about in the mine and concentrator. They are: (1) A change in backfill procedure for filling stopes below the 3900 level. (2) A 12,000-ton,per-day sink-float plant at the concentrator. (3) A new haulage system from the mine to the concentrator. (4) A completely new crushing plant and ore storage facilities located underground. A brief outline of the background and history leading up to this overall project will be given to show how each started as an independent betterment and how they were finally co-ordinated into one major programme. The first of these, namely, the necessity for backfilling stopes below the 3900 level, was the most pressing problem. All filling to date bad been done above the 3900 level, where mining was carried on in an irregular pattern of open stoping. Stopes below the 3900 level were first opened in 1940 and are being worked on a regular pattern of panel sub-level open diamond drill stopes. The two areas are separated by a sill pillar traversing the entire length of the vein at the 3900 level elevation.

Jan 1, 1950