Search Documents

By John C. Luck Jr.

"DEVELOPMENT of oil emulsion mud dates back to the early days of rotary drilling when oil was added to the drilling mud solely for the purpose of freeing stuck drill pipe. After the drill pipe was freed, and drilling resumed, this oil was considered a contaminant. Efforts were made to remove the oil but some of it remained and was emulsified with the drilling mud, thus forming a mechanical emulsion.During the late 1930's, operators found that adding crude oil to drilling muds seemed to alleviate 'sticky-hole' problems and so oil was allowed to remain in the mud. This practice was adopted when it was found that faster drilling rates and longer bit life were obtained. These observations led to the development of emulsion drilling muds. During the past five years their application has become more widespread because of the lower fluid losses obtained, greater lubrication qualities, faster penetration rates, and generally better hole conditions.An emulsion may be defined as a two-phase system consisting of a mixture of either finely divided oil droplets in water or of finely divided water droplets in oil. The surrounding liquid is known as the continuous phase. The emulsifiers reduce the interfacial tension, making the droplets tend to repel each other so that they remain dispersed and stabilized. These emulsions are classified as oil-in-water or as water-in-oil, depending upon whether water or oil, respectively, is the continuous phase. Briefly, close inspection shows that they consist essentially of globules of• the one liquid suspended in a continuous mass of the other liquid. Oil emulsion muds are usually of the oil-in-water type. Two basic types of emulsifiers •commonly used in Canadian muds are soaps and lignites."

Jan 1, 1954

This paper outlines the position and capabilities of Western Canada's bituminous coal industry, and indicates the increasing importance of Japan as an export market. The use of coal in Japan is reviewed, especially as regards future trends, and an appraisal is made of Canadian coal in comparison with domestic Japanese coal and imports from other countries. The importance of maintaining a solid nucleous within the Canadian bituminous coal industry is emphasized. I N RECENT years, Japan has emerged as a valuable market for Canadian exports. The first major product exported in volume to Japan was wheat, which has become very successfully established in Japanese markets. Following this, iron ore gradually found a market in Japan, with exports usually based on long-term contracts. This iron ore was produced entirely in British Columbia In 1958, the Western Canadian bituminous coal industry -jointly with the Dominion Coal Board -sent an official mission to Japan to investigate the

Jan 1, 1964

By L. Veleva, Garcia. A., G. Perez

Aluminum is a metal used for the transmission of electricity of high voltage, in the construction industry and other areas. In atmospheric conditions aluminum forms an oxide layer (Alz03'H20) as a result of its corrosion, entering the passive state. The oxide layer can be destroyed by the presence of ions (Cr, SOx-n) developing localized (non uniform) corrosion attack by pitting, difficult for evaluation. The concepts of fractals and self-similarity were used in this study for the characterization of the development of localized corrosion. Images obtained with a scanning electron microscope (SEM) of samples of electrolytic aluminum wire that have been exposed during one year in ruralurban and marine-coastal environments of the humid tropical climate of Mexico, have been processed. The development of pitting has been studied as a function of time, making a statistics of the frequency of appearance of pits versus the area occupied by them. The data show that the distribution of the pits follows a power law. Therefore, the concept of self-similarity can be applied for the study of the phenomenon of localized corrosion, describing their development with time.

Jan 1, 2006

By M. J. Merwin

Heat treated seamless tubular products are processed in a fashion that can be easily modified to produce dual phase microstructures, through the implementation of intercritical soaking prior to quenching. Dual phase steels are known to possess low yield strength compared to tensile strength. The steel line pipe market is interested in low yield-tensile ratio materials for application in reel barge pipe laying operations. In the current work compositions of commercially produced material already in use for the line pipe market were examined and dual phase microstructures were successfully developed. The microstructure and properties of the materials were found to be stable over the range of intercritical temperatures employed. Tempering temperature and, somewhat unexpectedly, small chemistry differences were found to have the largest influence on properties. Excellent toughness performance was observed in samples tempered at temperatures in excess of 550°C. Tempering in this temperature regime produced materials with strength suitable for application as API X60 line pipe. A difference in tensile strength between steels of similar chemistry was observed, and is not fully understood at this time. Welding performance was considered through simulation of three regions of the heat-affected zone. Neither intercritical temperature, nor tempering temperature, were found to have a significant influence on the heat-affected zone properties. The peak temperature achieved in the thermal cycle was the only significant factor. The hardness of the heat-affected zone was found to increase continuously with increasing peak temperature. While toughness was found to be low for both partially-transformed and coarse-grain heat-affected zones, the toughness of the fine-grained heat-affected zone was substantially better. Based on the results found in this laboratory study, a limited production trial is expected.

Jan 1, 2005

By A. E. McIlhinney, I. E. Puddington, C. E. Capes, A. F. Sirianni

"Two main problems are associated with the removal of pyritic sulphur from coals. The first is due to the fine state of dissemination of pyrite, which requires grindin1 to a very fine size to accomplish liberation. The second problem is caused by the similar surface chemical characteristics of coal and pyrite, which complicates separatio11 methods based on this property. In the work described here, the problem of fine particle size was overcome by using the selective oil agglomeratioa method developed at the National Research Council of Canada. Recovery of more than 90% of the combustible values was possible, even with particles only a few microns in diameter. Experiments using conventional chemical depressants for pyrite met with little success. It was found, however, that pyrite may be rejected during coal agglomeration through treatment with the iron.oxidizing bacteria, thiobacillus-ferrooxidans. The conditions for maximum pyrite separation are described and possible mechanisms by which the bacteria act are discussed."

Jan 1, 1973

By Zhiyang Long, Ruiling Xiao

"A mine shaft is one main development method of establishing access in an underground mine. The construction technology of the mine shaft sinking is complicated and large equipment setup on surface and in the mine shaft. The paper briefly reviews a single-line operation method, parallel operation method and mixed operation method as well as the features of the one operation method with the excavation, lining and installation. The special construction technology mainly would include ground freezing methods, full diameter shaft drilling methods, caisson methods, grouting technology and concrete curtain methods as well as other methods. The paper summarizes the shaft sinking numbers and effects by the special construction methods during different periods. The paper states the shaft sinking conditions and the each created record conditions in the coal, metallurgy, non-ferrous metal, hydropower, highway, railway, nonmetallic and other industries. The paper has a prediction on the shaft sinking requirements and development tendency in the future for China.INTRODUCTIONA mine shaft is one main development method of access in an underground mine. In recent years in China the new shaft mines represent 45% of the total number of new mines. With the development of new mining area under construction and the development of deeper mines, the ratio of the mine shaft as access for underground mines will increase. The construction technology of the mine shaft engineering will be complicated, the operation site footprint will be small and the working environment will be more difficult. The mine shaft sinking operation will often be varied by the geological conditions and affected by underground water inflows, seam gas outbursts, geothermal and other natural conditions. The safe construction of the mine shaft sinking will be challenged by all these conditions. Although the mine shaft engineering will only be about 5% of the total mine roadway engineering, the mine shaft construction period often will take over 40% of the total mine construction period. With the progress of modernized mine production technology and the construction of a high production and high efficient mine, the mine transportation roadways mostly would be set in the seam and the engineered amount of the mine rock roadways reduced year by year could cause more prominent long extensions of the mine shaft construction period. Therefore, in order to speed up the construction, to shorten the mine construction period and to realize the investment benefits as early as possible, the technical level of the mine shaft sinking should firstly be improved and the construction speed of the mine shaft engineering and sinking should be speeded up, which would have important significant benefits."

Jan 1, 2019

By A. Iizuka

This study was aimed at separating and recovering arsenic, antimony, and tin from refining byproducts generated in a nonferrous smelter. The target byproduct was a silicate slag containing the above elements. The silicate structure of the slag was destroyed by alkali roasting, which then enabled leaching of arsenic, antimony and tin in solution effectively. Arsenic was selectively leached out by hot water after alkali roasting of the slag, while remained antimony and tin in the residue were leached out by a hot hydrochloric acid solution. However, when the solid-liquid ratio in the leaching solution was increased, hydrous gelatinous silica (gel-like silica) was formed during the hydrochloric acid treatment and filtration became difficult. Therefore, high temperature and high pressure leaching was attempted to improve the filterability of the silica leaching residue. In the high temperature and high pressure treatment, the hydrous gel-like silica was transformed into easily filterable aggregated silica, and thus, filtration became easy. By investigating the neutralization and sulfurization treatment for the obtained hydrochloric acid leachate (second leachate), it was possible to separate antimony and tin. INTRODUCTION This study aims to separate arsenic and recover valuable metals such as antimony and tin from refining byproducts generated in a nonferrous smelter. The target smelting byproduct is antimony-containing slag in this study. In many cases, alkali roasting was adopted as pretreatment for extraction and recovering valuable metals from smelting residues and wastes (Rao, 2006). For antimony-containing slag in this study, one effective method for separating arsenic is to convert arsenic to sodium arsenate (Na3AsO4) by roasting with a sodium compound and then to remove arsenic by hot water leaching. In addition, by alkali roasting, the silicate structure of the slag is destroyed, and effectively alkalizing tin and antimony is accomplished. Then, precipitating and recovering tin and antimony leached into the acid solution are considered possible by sulfurization and neutralization treatments. In this research, we conducted basic studies on the following. 1) Destruction of silicate structure in slag by alkali roasting and leachability of arsenic. 2) Conversion of hydrous gelatinous silica to aggregated silica by hydrochloric acid treatment of residues after arsenic leaching under high temperature and high pressure, as well as leachability of antimony and tin. 3) Separation and recovery of antimony and tin by sulfurization and neutralization treatments of hydrochloric acid leachate. These topics of investigation can support to consider the separation and recovery process of arsenic, antimony, and tin from antimony containing slag.

Jan 1, 2019

By C. Gordon Saunders

"The ungraded-fibre mill is located at the mine site and has a rated capacity of 6,600 tons of ore input and 1,200 tons of ung1•aded fib1 •e product per day. Power for operation is obtained from a diesel generating plant located on the site, which has a capacity of 5,300 kW. The preliminary milling process consists of prima1•y and secondary crushing, drying and temporary storage of plus-1 1h -in. material. The final milling processes are two stages of crushing and three stages of screening, with air-lift separation of the fibre from the host rock. The central mill building also houses a machine shop, mill maintenance shops, a mobile equipment overhaul shop, an engine and majo1•-component overhaul shop, and a warehouse. Major changes to the milling ci1•cuits since start-up have been the addition of a larger secondary cone crusher, ct third dryer, adding a rotary distributor to the feed of the screening section and adding an automatic start-up sequence for all equipment except crushers and fans. The operation of the mill is coordinated from a central control room, where a ""mimic"" panel indicates the operation of all major units in both the ore preparation and the screening sections. Product quality is controlled by continuous sampling and frequent labo1•atory analysis, which provide data fm• the adjustment of aspirating hoods and mill feed rate. Operating problems unique to this location, and common to a sub-arctic environment, are discussed."

Jan 1, 1976

By G. Mousavian, R. Bagheri, N. Dalili

Polypropylene (PP) and its composites have an increasing use in automobile and domestic industries. Since the published results on strain rate effect on yield behavior do not match, and there is a high attention paid for effect of nanometeric fillers on deformation behavior of composites, in this research the strain rate effect on yield behavior of PP and the effect of nanometeric fillers on deformation behavior of PP have been studied. Microscopic observations and tensile tests in different strain rates on neat PP samples and on samples filled with 5, 10 and 15 %wt have been used. A dramatic change in behavior for the modulus and post-yield slope curves when the strain rate is between 0.0433-0.05 s-1 has been observed. Microscopic observations on PP indicate a change in deformation mechanism from shear yield to crazing at the same strain rate that the change in behavior of curves occurs. It has been observed that in PP nanocomposites with higher amount of calcium carbonate, fracture in early stages of deformation occurs in lower strain rates. In other words for a fixed stain rate there is a critical filler percentage such that if the filler percentage is higher then early-stage fracture will occur. Similarly for a fixed filler percentage there is a critical strain rate and in higher strain rates early fracture will occur. The critical stain rate will decrease as the filler percentage increases and vice versa.

Jan 1, 2006

By P. N. Calder, D. B. Apel, S. D. Butt

Mine-wide (MW) microseismic systems use widely spaced transducers to determine the source location and parameters of stronger microseismic events, while high frequency (HF) systems use fewer transducers to monitor local areas for the weaker events that can precede stronger events. Previous monitoring at the Creighton Mine indicated that an HF transducer located 120 m away from an active stope recorded two types of activity in response to production blasting: the first occurring at the same time as the production blasts and associated with the passage of the direct seismic waves from the blast through the local area, and the second occurring several hours later and associated with the arrival of a slower moving stress change through the rock mass (which was identified by the mine’s MW system). Interpretations of locally increased stress levels, based on analysis of the recorded HF events, correlated with the nearby occurrence of two strong seismic events. These results were applied to a similar monitoring trail at the Kidd Creek Mine where the transient stress changes induced by several development blasts were monitored. It was observed that increases in HF activity corresponded with the occurrence of MW events near the transducer location, and that fewer HF events were recorded the longer this occurred after the blast. Local geological features appeared to influence the number and occurrence of both HF and MW events.

Jan 1, 2000

By H. Hamza

Efficient and effective management of extraction process tailings is an essential ingredient for the continued success and development of Alberta's vast oil sands resources. Open-pit oil sands operations north of Fort McMurray recover bitumen from flotation circuits. Process tailings are managed in carefully engineered and monitored external tailings management facilities and in below-grade mine pits. In order to support reduction of production costs and improve upon established tailings management practices, CANMET has been working with the oil sands industry in a collaborative framework to assess the potential to integrate thickened tailings into oil sands extraction process flowsheets. Albian Sands has commercialized the process while others, including Syncrude Canada Ltd., continue to evaluate the suitability of the process for their operations. This paper provides an update on R&D work undertaken in recent years to assess and develop the potential of thickened tailings technology for the open-pit oil sands operators of northern Alberta. The aim of this work was to explore opportunities to optimize process efficiency and environmental sustainability by improving water and energy conservation and develop more alternatives for tailings management and reclamation.

Jan 1, 2004

By W. H. Patterson

The history and experience of early companies in the Islands is illustrated by the typical transactions of Trans-Western from 1959 to date. Trans-Western had entered into farmout agreements with companies strong enough to carry out at least the required minimum exploratory work and then such development as might be warranted. The farmee companies were required to make deposits to guarantee work performance during the first period of validity, i.e. the first 3 years of the 12-year life of the permits, and at the rate of 5 cents per acre. At that time, a good deal of geology was available, as a result of extensive exploration that had been carried on by the Geological Survey of Canada and other geological enterprises, with field parties travelling over and camping on all of those Islands. Trans-Western's farmees then selected, from Trans-Western's priority on 13.5 million acres, what they believed were the lands most prospective of producing large oil and gas discoveries, and, having the right to trim off acreage which they considered less prospective, thereby reducing the acreage of Trans-Western and its farmees to in excess of 5.5 million acres. The farmees then commenced a 3-year program carrying out geological exploration to the required minimum of 5 cents per acre, and with some permanent and many mobile camps.

Jan 1, 1969

By O. S. Perry, G. H. Charlewood, K. Griffin, S Ogryzlo, H. Hopkins, G. MacIntosh

"The gold mines of Kirkland Lake are in Teck township, Timiskaming district, Ontario, latitude 48°9'N. and longitude 80°3'W., at an elevation of 1,038 feet above sea-level.There are seven contiguous producing mines in a length of 3;1/2 miles along the general east-west strike of the deposits. The seven mines are, in order from west to east, Macassa, Kirkland Lake, Teck-Hughes, Lake Shore, Wright-Hargreaves, Sylvanite, and Toburn.The first discovery of gold in the zone was made by W. H. Wright in 1911 on the east claim of the Wright-Hargreaves property, and the following year the Tough brothers and H. Oakes found gold in what is now the No. 1 vein_ at the Toburn. Production began at the Toburn in 1915, followed by Teck-Hughes in 1917, Lake Shore in 1918, Kirkland Lake Gold in 1919, Wright-Hargreaves in 1921, Sylvanite in 1927, and Macassa in 1933.To the end of 1946, 31,938,350 tons of ore had been milled at the Kirkland Lake mines, from which 16,132,700 oz. gold, having a value of $498,517,600, were recovered. The bullion varies from mine to mine between 800 and 900 fine, the average for all the mines being 853. The average fineness of the native gold is 941.The workings of some of the mines are more than 6,000 feet deep and sinking to depths below 7,000 feet is now in progress.GENERAL GEOLOGYThe regional structural geology of the area in which the mines of Kirkland Lake occur is described in a preceding paper in this volume by J. E. Thomson."

Jan 1, 1954

By Gennaro Delisle

"Les Services TMG (Niobec) currently treat a niobium ore in the Chicoutimi area of Quebec. The mineral pyrochlore is present in a carbonatite deposit which assays 5% to 7% apatite.The ore is ground to minus 65 mesh and deslimed at 10 micrometres. Part of the carbonates are floated with a fatty acid emulsion and rejected to the tailings as a first step to ensure the proper conditions for the flotation of the pyrochlore concentrate. The carbonate concentrate is 65% minus 44 micrometres and is composed of dolomite, calcite, 22% apatite and a minor amount of silicates.A laboratory investigation was undertaken to determine the feasibility of extracting apatite from the carbonate concentrate. This led to the development of an economic flowsheet to produce high-grade apatite concentrate. The apatite is depressed with phosphoric acid, and the pH is adjusted at 4.8-5.0 with sulphuric acid. An additional amount of fatty acid is added to permit efficient flotation of the carbonates. 1n a second stage, the silicates left behind with the apatite concentrate can be removed by depressing the apatite with AIC3 while floating the silicates with a secondary amine.The results of the laboratory tests indicate the possibility of producing an apatite concentrate assaying 38.3% P2O5 (83.7% BPL) with a recovery of 66.2%. Pilot-plant tests undertaken at the concentrator yielded a concentrate of 34% P205 and recovery of 76%."

Jan 1, 1981

By C. Hu

A MOS capacitor hydrogen sensor array is reported for hydrogen gas distribution mapping. Si(100) was used as substrate for film deposition. After silicon oxide growing on the silicon surface with dry thermal oxidation, palladium film was sputtered on silicon oxide as hydrogen-sensitive gate material in MOS structure. The 3x3 sensor array was patterned on silicon substrate and packaged in one chip. Sensors' response was test with impedance analyzer. The sensors in array were calibrated in the hydrogen concentration range from 10ppm to 10000ppm. The 2D hydrogen concentration distribution was obtained with the calibrated sensor array.

Jan 1, 2005

By R. S. Jr. Stronach

"IntroductionThe property of Campbell Red Lake Mines, Limited, is in Balmer township, Red Lake area, Patricia portion of Kenora district, Ontario. It consists of a group of twelve claims which had been staked and re-staked a number of times before George W. and Colin A. Campbell staked them in 1944. Messrs. Brewis and White incorporated Campbell Red Lake Mines, Limited, in July, 1944, to acquire these claims from the Campbell brothers, and in November of the same year re-assigned their option on the controlling interest of the treasury shares to the Dome Exploration Company (Quebec), Limited, a wholly owned subsidiary of Dome Mines, Limited.A long known exposure of sulphides on the northeasterly portion of the property, which returned low gold assays, on sampling, was the only showing of interest at this time. However, Dr. H. C. Horwood's report and map of the district had recently been published and favourable structure W3.S indicated in Balmer township. It was on the strength of this showing and Dr. Horwood's report that Dome Exploration became interested in the property.Between. January, 1945, and April, 1946, a diamond drilling programme was carried out, with completion of sixty-one holes. Five holes proved the surface showing to hold no commercial interest, so routine cross-sectioning of the property from north to south was started. The fourth hole of the series returned excellent ore intersections and from that time on the programme changed to one of extending these values. The final results of the drilling showed that what is now known as the A zone has a continuous length of some 1,200 feet, a width of 4½ feet, and an overall grade of about 0.5 oz. gold per ton. There were many other intersections of ore grade outside this A zone which could not be successfully correlated .at that time, but underground work has opened many of them. It may be said here that practically all the work to date has been confined to the southeast claims of the property."

Jan 1, 1950

By G. M. Ritcey, B. H. Lucas

In the conventional alkaline leaching of concentrate containing nickel, copper and cobalt, copper is usually removed from the system, prior to nickel reduction, by sulphide precipitation. A new process is described for the selective extraction of copper and separation from cobalt and nickel, using liquid-liquid extraction. General Mills LIX-63 dissolved in a kerosene diluent is the extractant. Trace amounts of co-extracted cobalt and nickel are easily removed by a scrub treatment, and copper is recovered from the extract by sulphuric acid stripping, thus providing a solution amenable to the oroduction of electrolytic copper. Estimated processing costs are included together with a proposed flowsheet.

Jan 1, 1972

By H. P. Dibbs

An account is given of the application of neutron activation analysis to the rapid, non-destructive determination of copper in minerals, using a 14-MeV neutron source. Elements that interfere in the determination of copper by this method are given, together with the errors in the estimation of copper that result from the presence of varying amounts of these elements. The possible use of a compact "sealed-tube" 14-MeV neutron generator for the field assay of copper in minerals is discussed.

Jan 1, 1970

By G. S. Barry

INVESTIGATIONS to date have shown that, should there be the need or the appropriate economic stimulus, Canada's mineral resources are sufficiently extensive to allow considerable expansion of its non-fuel mineral industry, during the remaining part of this century and possibly beyond (1, 2). The availability of sufficient capital will be one of the critical factors which will determine whether this potential will be fulfilled. The following analysis centers on the capital requirements of the Canadian non-fuel mineral industry under one set of basic assumptions of capacity growth, cost of new and replacement capacity, rates of depletion and depreciation of mines and plant, and the cost of exploration and infrastructure. Mindful of the fact that exploration and development will not thrive in Canada unless a very positive approach is taken, the writers make no apologies for being "optimistic" about long-term production prospects. Furthermore, in the event that world demand does escalate as anticipated and the forecast realistically attainable levels of Canadian production are not reached, then Canada will not have reaped the full range of economic benefits available, and opportunities will have been lost. Projections for Canadian production between 1976 and 2000 are essentially based on the forecast published in the 1974 paper, "Towards a Mineral Policy for Canada - Opportunities for Choice (3), with some updating on the basis of recent developments.

Jan 1, 1977

By William B. Hetherington

Communities are the foundation upon which the whole structure of society rests and upon which the nation builds its hope for the future. They are not established to serve any one particular generation, nor any one element or group, but should be erected to render a lasting service to all who are to follow. They play a very vital and important role in the lives and welfare of the people, in their industrial, business, and social relations, and in the economy of the nation, of which they are the fundamental assets. Communities and civic governments are destined to be vital factors in the national welfare in the days that are to come. Any improvement in national or world conditions must have its origin within the communities. Any attempt at solution of the community problem must give some consideration to the fundamental elements which exist in every community, and to the underlying principles, and ways of life and thought, upon which community life is based. The community is, in its essence, a number of people living and working more or less closely together, sharing common rights, privileges, conveniences, and comforts, which would be impossible for the individual to obtain for himself by his own efforts alone, or in any other way than by the mutual exchange of persona! services and resources. In this way, men have increased the returns from their labour and commerce, have raised the standard of their living, with better social, educational, and recreational facilities, and enjoy a greater personal security.

Jan 1, 1943