Search Documents

By M. Epiney, A. Ghahreman, R. Kim1and

"In the presence of sulfidic refractory ores, increasing the dissolved oxygen (DO) concentration can positively affect the gold leaching rate. To identify the role of DO in gold cyanidation, electrochemical behavior was studied in the presence of 3 different ores. Sample 1 was a low sulfide pyrite ore, contained 5.14% pyrite, 0.19% galena and 3.09% S. Sample 2 was a pyriticore as well, contained more sulfide as 8.35% S, and 12.4% of pyrite. Sample 3 was a tailing of silicate gold ore, still containing75 g/tAu, 0.13% Pb and 0.18% S. Gold cyanidation kinetics were studied by cyclic voltammetry (CV) and chronoamperometry tests. With sample 1, the gold oxidation peak current density from CV curve was increased to 1.38mA/cm2under oxygen injection, while it was only 0.66 mA/cm2with air injection. From chronoamperometry test, the reaction rate was also faster under oxygen injection. Sample 2 showed similar behavior with sample 1, but the gold oxidation peaks higher than sample 1, i.e. 1.75 and 2.27 mA/cm2, under air and oxygen injection, respectively. However, it seemed that the gold oxidation was impeded by sulfide ions for a longer period. In the presence of sample 3, the gold oxidation peak was the highest among three ores –2.75mA/cm2under oxygen injection, because of its lowest sulfide content. However, from chronoamperometry test, it was also shown that the gold oxidation was impeded because of a significant amount of Pb in the ore sample.INTRODUCTIONIt is well known that gold is leached under oxidative condition (Marsden &House, 2006). Through the most representative and oldest gold leaching technique, cyanidation, more than 90% of gold can be selectively leached from an ore. According to Elsner’s equation, gold is leached in cyanide solution by forming cyanide complex [Au (CN)2–], and oxygen is consumed as an oxidant(Eq. 1)."

Jan 1, 2017

By P. G. Smith, A. Axiuk

The objective of this paper is to present, from a practical perspective, a review of the most relevant maintenance procedures that are accepted or prescribed to be the most effective in optimising service life potential and to ensure continued safe use of steel wire ropes for shaft mining applications. The paper will address the most common operational issues encountered in the care and operation of shaft ropes for both conventional drum hoists and multi-rope friction winders. For each distinct maintenance procedure presented, a limited amount of theory is discussed to identify the underlying mechanisms at play that must be addressed and to emphasize the logical basis for the recommended course of action. It is recognised that each installation is unique and that the recommended maintenance procedures may not always be practical or cost effective from an operations standpoint under select circumstances, however the intent remains to promote industry best practices for the knowledge and benefit of the mine hoisting community, from experienced maintenance personnel to new entrants to the industry alike.

Jan 1, 2023

By M. Abumiya, N. Onodera

"The synthesis of large scorodite particles in non-ferrous metallurgical industries usually requires a high-cost operation involving heating and high-pressure autoclaving. To overcome these obstacles, an atmospheric-pressure process for scorodite synthesis (DMSP®) was developed, in which ferrous ions were oxidized by oxygen gas in the presence of pentavalent arsenic ions. This process gives scorodite of good crystallinity with particle sizes as large as 15-20 µm. The solutions used for scorodite synthesis in the DMSP® are prepared from various residues containing arsenic from non-ferrous smelters. The solutions may be contaminated with Cu, Sb, and Bi, for example, and therefore the effects of such impurities on the formation of crystalline scorodite need to be investigated. In this study, the effects of Cu, Sb, and Bi contaminants on the formation behaviors of scorodite particles in the DMSP® were investigated systematically.INTRODUCTIONThe synthesis of crystalline scorodite (FeAsO4·2H2O) is a suitable method for arsenic (As) stabilization and storage of As-containing by-products such as flue gas dusts in non-ferrous smelters. It is expected that the formation of large, highly-crystalline scorodite particles would be an ideal method for avoiding the release of arsenic to the environment. Generally, autoclave methods under pressurized oxidation conditions at temperatures above 100°C have been used for the formation of arsenic minerals such as scorodite. However, the autoclave method requires sealed vessels that are resistant to high pressure, heat and acids. This process is also unfavorable on account of the high construction expenses, and high running costs as a result of vapor heat loss. Processes for synthesizing scorodite under atmospheric conditions at temperatures below 100°C which do not need an autoclave have therefore been extensively investigated (Demopoulos, Droppert, & VanWeert, 1994; Demopoulos, 1996; Demopoulos, Lagno, Wang, & Singhania, 2003; Droppert, Demopoulos, & Harris, 1996; Filippou & Demopoulos, 1997).Recently, Fujita et al. (Fujita, Taguchi, Abumiya, Matsumoto, Shibata, & Nakamura, 2008a, 2008b, 2009; Fujita, Taguchi, Kubo, Shibata, & Nakamura, 2009; Fujita, Taguchi, Shibata, & Nakamura, 2009) developed a new method for producing large scorodite crystalline particles with improved filtration and washability properties at normal atmospheric pressure and temperatures below 100°C. In the new method, oxygen gas (O2) is blown into solutions containing a high concentration of arsenic ions (As(V)) and ferrous ions (Fe(II)). The Fe(II) ions were subsequently oxidized to ferric ions (Fe(III)), resulting in the formation of large scorodite particles. High supersaturation of solutes such as Fe(III) will result in excessive nucleation, and the formation of poorly crystalline phases. The scorodite formation must therefore be conducted in a manner that avoids the critical supersaturation level being exceeded. It is supposed that the oxidation of Fe(II) to Fe(III) by O2 gas in the new method suppressed the supersaturation of Fe(III) during scorodite formation. The low Fe(III) supersaturation resulted in formations of highly crystalline scorodite particles of size of around 20 µm. In June 2008, based on the developed process described above, DOWA began experiments to verify the industrial capability of a plant with a capacity of 30 MT/month of As. It was successfully proven that it is possible to produce crystalline scorodite industrially on a commercial scale. This process was named and trademarked as DMSP® (Kubo, Abumiya, & Matsumoto, 2010)."

Jan 1, 2012

By T. G. Joseph, M. J. Bolster

ABSTRACT This paper explores passive seismic measurement as an alternative, nonintrusive approach to conducting annual brake testing on surface mine sites. Dictated by the test site location, this evaluation adhered to the brake testing procedure as per British Columbia occupational health and safety regulations. Results showed excellent correlation to those reported via conventional practice: Comparing stopping distance, time, and velocity for the proposed instantaneous passive seismic versus conventional approaches, less than a 0.5% variance was evident. A viable alternative, the passive seismic approach, allowed an entire fleet of trucks to be sequentially evaluated for annual brake testing without disrupting operations by installing mechanical testing equipment.

Jan 1, 2012

By Arthur L. de Carle

"IntroductionThe Key Lake uranium-nickel deposits are located within a Mineral Lease centred at latitude 57 ° 12' north and longitude 105 °39' west along the southeastern rim of the Athabasca sedimentary basin in northern Saskatchewan, approximately 240 km north of La Ronge (Fig. 1). Access is provided by an allweather provincial highway from Pinchousc, situated about 200 km to the south, and a private airstrip maintained at the mincsitc.These deposits have been developed by Key Lake Mining Corporation on behalf of the Saskatchewan Uranium Joint Venture. Participants in the joint venture include Saskatchewan Mining Development Corporation (50%), Urancrz Exploration and Mining Limited (33 1/3 %) and Eldor Resources Limited (16 2/3 %).Considerable geological work has been conducted on the Key Lake orebodies and reported in summary papers published by Dahlkamp and Thn, (1977), Dahlkamp, (1978), Gatzweiler eta/., (1979) and Kirchner el a/. , (1980). However, intensive geological research is ongoing, particularly since many problems regarding ore genesis and controls remain unresolved . Exploration History and DevelopmentThe events (Gatzweiler eta/., 1980) which led to the discovery of the Key Lake ore bodies began in the summer of 1971 by following up on the reports of airborne radiometric anomalies and anomalous radon values in the Zimmer Lake water situated approximately 5 km to 6 km to the southwest. This work succeeded in locating a few high-grade uranium and nickel-bearing boulders associated with esker material. An integrated program, consisting of various geochemical and geophysical surveys along with diamond drilling, culminated in the discovery of the Gaertner orebody during July 1975. Subsequent fence drilling across the strike extensions of this ore structure located the Deilmann deposit, approximately I km to the northeast, in June 1976"

Jan 1, 1986

By C. R. Stelck

"AbstractThe Cardium formation of northeastern British •Columbia •contains an erosional unconformity that becomes progressively more severe northward until, •at Liard river, the stratigraphic hiatus eliminates the underlying Lower •Cardium sandstone, the Kaskapau formation, and the upper Dunvegan sandstones. The area of unconformity roughly coincides with the distribution of the continental facies of the earlier Dunvegan formation. Along Wapiti river, the zone fossil Scaphites ventricosus Meek and Hayden is found in the Bad-heart member of the overlying Wapiabi shale; Scaphites :preventricosus. Cobban marks the base of the Wapiabi shale; Scaphites cf. corvensis •Cobban is found in the middle shale member of the •Cardium formation. The log of the Red-Willow No. 1 well shows close similarity to the outcrop sections south of Wapiti river. The Cardium formation is mainly late Turonian in age. Two other pre-Cardium Turonian sands of north-eastern British Columbia are named the Wartenbe and Tuskoola sands.IntroductionTHE Upper Cretaceous Cardium (Bighorn) sandstone formation of the Foothills of northeastern British Columbia carries within its formational limits an erosional unconformity. The unconformity decreases to the southeast, becoming in immediate shoreline regions, now under the plains, a minor diastem. Such diastems, or stratigraphic intervals of non-deposition, occurring in the shallow unda-zone are paralleled in the deeper portions of the unda-zone by the phenomena of sub-aqueous winnowing. '.This winnowing and re-working •at critical depths creates sand areas with porosity."

Jan 1, 1955

By Anna Maria Venezia

Bimetallic Au-Pd catalysts supported on amorphous silica-alumina (ASA) with vary amount of alumina (0, 8, 14, 28 and 100%) were prepared by the simultaneous reduction of palladium and gold precursors by ethanol in the presence of the polyvinylpyrrolidone (PVP). X-ray diffraction and X-ray photoelectron spectroscopy analyses indicated formation of alloyed Au-Pd particles. Ammonia temperature programmed desorption measurements were performed to monitor the acid strength and the amount of acid sites on the catalysts after their reduction with 10%H2/Ar at 573 K for 1h. The effect of the support acidity on the catalytic activity was investigated in the simultaneous hydrogenation (HYD) of toluene (T) and naphthalene (NP) in the presence of dibenzothiophene (DBT). Coke formation was also determined. Under the selected conditions (P = 5.0 MPa, T = 523 K, WHSV = 41.2 h-1), all the catalysts were resistant to poisoning with 113 ppm of S (as DBT). The hydrogenation activity of toluene and the HDS activity of DBT were found to correlate with the concentration of the medium strength acid sites. The enhancement of the HYD activity and the S- tolerance was related to modifications of the electronic properties of the metal atom upon interaction with the Brönsted acid sites and upon intermetallic interaction.

Oct 1, 2003

By F. H. Samuel, H. Tahiri, S. Valtierra, H. W. Doty, A. M. Samuel

L'affinage des grains dans les alliages d'aluminium consiste à augmenter le nombre de sites de cristallisation de la phase a-Al afin d'obtenir une structure fine. Les alliages mères de type Al-Ti-B sont largement utilisés comme raffineurs des grains. Cette étude a pour but d'établir des mécanismes convenables d'affinage des grains dans l'alliage A356 en utilisant cinq alliages mères et deux températures de coulée (750°C et 950°C). Les résultats montrent que la phase a-Al prend une forme selon l'alliage mère ajoute; les échantillons coules a haute température montrent une taille de grain plus grosse; les températures de germination et de croissance augmentent avec I' augmentation du Ti ou du B et la taille des grains diminue. L'alliage mère Al-4%B montre une puissance remarquable en comparaison d'autres alliages mères. Pour cet alliage mère, le titane résiduel dans l'alliage A356 réagit avec le bore pour former TiB2 qui, par la suite, agit comme un germe actif pour la phase a-Al.

Jan 1, 2006

By J. S. Moretzsohn, D. F. Graham

"Airborne Synthetic Aperture Radar (SAR)was acquired over the Carajás Mineral Province, within the rainforests of the Amazon, which hosts the world’s largest Fe-ore deposit(Santos, 1986). Significant chemical weathering exists in this humid environment. PrevalentAu mineralization is thought to be generally associated with deformation zones in Archean schists.Radar data have proven to be very useful as an aid to geological mapping in the tropical rainforests of the Amazon Basin in Brazil. In these densely vegetated areas, a sense of regional structural trends is obtained as a con-sequence of the sensor/terrain geometry. The top forest canopy is the main terrain reflector of X-band radar energy, and consequently is the main terrain surface feature expressed in processed radar imagery. Radar is important for extending t,he continuity of mapped structural lineaments. Differential weathering is related to variations in radar image texture which is used to infer gross lithologic variations and relative age relationships of major rock units. Specifically, quartzites and banded iron formation are highlighted in the radar imagery due to their unique tonal and textural appearance, in contrast to schists, gneisses and metavolcanic rocks. As tropical areas are typically enveloped in cloud or mist, radar data are invaluable in providing information for logistical planning of field mapping activities."

Jan 1, 1997

By A. McMullen

"IntroductionTHE LOW-VOLATILE bituminous coals of the Brazeau field, Nordegg, Alberta, are soft and weak in structure. The seams contain .bands of inferior material, locally designated 'black jack', and thin bands of friable carbonaceous shale having no definite horizon but usually 'floating' in the seam. Because of the weakness• of the coal and the friable nature of the shale bands, run-of-mine coal usually contains a very high percentage of fines, as •Shown in the following table:SIZE WEIGHT. %Plus 1/2 in 25.61/2 – 1/4 in 13.31/4 - 1/8 in 14.6Minus 1/8 in 46.5The most convenient way of cleaning the fine coal would be by treating it in association with the coarse coal, so that no additional plant would be necessary. To a limited extent this is possible in certain types of equipment, notably the jig. A system of washing without pre-sizing is not •attractive, however, when dealing with the friable coal under consideration, which contains •a preponderant proportion of fines. At the new Brazeau washery, separation is made at 3/8-inch on •a Robins 'Vibrex' •screen, the coarse sizes being cleaned in •a standard pulsator-type jig. A feldspar jig is used to clean the minus 3/8-inch fraction."

Jan 1, 1954

By J. S. Roper

"IntroductionSNOW LAKE is situated in northern Manitoba at latitude 54° 55 and longitude 100°, 400 miles northwesterly of Winnipeg, 80 miles northeast of The Pas, 80 miles east of Flin Flon. A 38-mile road from Wekusko, on the Hudson's Bay railway, serves the community.The mine is located in and close to the southern edge of the Precambrian Shield in typical low-relief muskeg and lake country.The Howe Sound Exploration Company, Limited optioned the property from Nor Acme Gold Mines, Limited, after preliminary diamond drilling had outlined two orebodies of low-grade arsenical gold ore.Following the examination and study of geological data and of 50,000 feet of diamond-drill core, and metallurgical tests made during 1942 to 1945, a decision was made to develop the mine and build a 2 ,000-ton mill concurrently. This development has been described by G. C. Lipsey in a paper entitled The Development of a Mining Operation from Diamond-Drill Data which was published in the August. 1952, issue of Mining Engineering.Geological Features of the OrebodiesThe orebodies at Snow Lake occur in volcanic rocks of acid to basic composition and, to a lesser extent, in intrusive hornblendite. The hornblendite is a massive, uniform, .coarse-textured rock except in the immediate vicinity of the ore zone, where it becomes sheared and carbonatized. The acid volcanics have been converted to quartz-garnet-biotite gneiss, and the basic volcanics to amphibolite gneiss. Orebodies have been formed by the replacement of all three rock types."

Jan 1, 1955

By T. P. Weldum, W. Conger

"These studies address the relationship between mill media sizing and its grinding efficiency. Starting with the results from a review of the literature, the issues of initial media sizing for a new ball milling circuit, and then optimal media sizing for an existing milling operation, were studied. The Functional Performance parameters “Mill Grinding Efficiency” and cumulative “Mill Grinding Rates” from both plant and test-scale equipment were used, and provide valuable new insight into this topic. A plant media sizing diagnostic tool is presented, as are newly developed testing equipment and evaluation methods, and recent case studies.REVIEW OF MEDIA SIZING LITERATURE For a plant metallurgist to answer the question “How can I maximize plant profit by manipulating this grinding circuit variable?” she must know what effect the variable has on grinding circuit efficiency. Despite the significant cost of grinding media and its potential effect on production capacity, the ‘best’ media sizing remains ill-defined for any given ball mill circuit in the industry today. The underlying reasons for this will be discussed. But the importance of this issue drove Metcom and its industrial partners to take on the challenge of how to engineer the ball charge for an existing grinding circuit. In the absence of any proven method, the first step was a review of the literature. Sponsored by Cleveland-Cliffs, Inc., a broad review of the literature was undertaken, producing “The Effect of Media Sizing on Ball Milling Efficiency” (McIvor, 1997). Among hundreds of publications that were reviewed that discuss the topics of media sizing or wear, forty-five were studied in detail. These were grouped into: plant experiences; laboratory and pilot plant investigations; media wear studies; population balance modeling studies; and general papers on ball milling which included the topic of media sizing. The reader is encouraged to refer to that review. The findings remain unchanged, although some relevant papers have been written since (e.g. Staples et al, 1997; Banasi et al, 1999; Orford et al, 2006; LaMarsh, 2015). The main findings of the review were as follows:"

Jan 1, 2018

By G. H. Long, D. H. Magnusson

THE DEFINITION of the continental margin, as considered in this paper, is in the broad sense: " ... those provinces of the continents and of the oceans which are associated with the boundary between these two first-order features of the earth" (Heezen et aL, 1959, p. 17). The provinces in the area under con-sideration are: the Continental Shelf, the Continental Slope and the Continental Rise. The Continental Shelf extends from the shoreline to the shelf break, which lies at approximately the 200-meter isobath through-out the region (except north of the Grand Banks, where the break may be defined more properly by the 400-meter isobath). The Continental Slope and Rise occur between the shelf break and the 4,000-meter isobath. (The last figure was somewhat arbitrarily selected for the purpose of this paper.) The Atlantic Continental Margin as thus defined extends along the eastern coast of Canada from the International Boundary in the Gulf of Maine northward to approximately the 60°N latitude off the coast of Labrador. The area of study amounts to at }east 500,000 square miles -an area roughly equivalent to 13 per cent of Canada's total land surface.

Jan 1, 1970

By A. J. Brown

This paper presents an economic evaluation of resin ion exchange and solvent extraction for the purification and concentration of uraniferous solutions derived from sulphuric acid leaching operations. Capital and operating costs are related to the uranium tenors of pregnant solutions. The conclusions drawn herein apply only to cases where resin and liquid ion exchange are technically feasible process alternatives. It is shown that solvent extraction is economically favoured for pregnant solutions at tenors greater than 0.90 gpl U3O8. Pregnant solutions with tenors below 0.35 gpl U3O8 are best treated by resin ion exchange. Between these concentrations, the economics are marginal and the favoured process is indistinguishable within the limits of accuracy of this study.

Jan 1, 1979

By A. Dubé

Introduction It is common experience that on re-heating a fully martensitic steel below the Ac, point, a softer and tougher structure is formed as the tempering temperature is raised. The mechanism of tempering of plain carbon and low-alloy steels has been the subject of many investigations. In a very comprehensive study, Cohen and associates have recently established three different tempering stages, the last of which reaches completion at about 700°F., with heating rates of 5°F. per minute. This latter stage has been established ta be the carbide-forming stage, so that the steel consists of a mixture of ferrite and carbide, which are the metastable equilibrium phases. Any subsequent changes which take place at higher temperatures below the Ac, point in the absence of graphitization or carbide lattice conversion normally consist of agglomeration of the carbide particles. This naturally results in the softening of the steel. However, in many cases the Ac, point, as determined by dilatometry, thermal analysis, etc., only gives a rough estimate of the temperature where the reaction, ferrite plus carbides to austenite, is initiated. This appears to be especially true in the case of alloy steels in which three phases can co-exist in certain temperature ranges. Bain has given data on the three-phase equilibrium in both manganese and nickel steels. In these steels, the formation of austenite at temperatures just above the AeIL apparently involves the diffusion of the alloying elements to the first pools of austenite, thereby making the process very sluggish. As a consequence, the critical Ac points determined by ordinary methods at normal rates of heating can be quite distant from the true equilibrium Ae temperatures.

Jan 1, 1946

By L. H. Cole

FOR many years Industrial Minerals, or as they were formerly called, 'the Non-Metallic Minerals', compared with the metallics, were considered of only minor importance and as such were given scant attention in the technical press as well as in the public press. Those days are, however, happily passing, and thanks, to an appreciable extent, to the constant endeavour of the Industrial Minerals Section of this Institute, established in the fall of 1932 industrial minerals are now assuming the importance to which they are entitled. The term 'Industrial Minerals', when first adopted in this sense by the Institute, was thought to be original in its application, but it is interesting to note that it had been used many years previously by the Queensland Geological Survey in the following publication: SALT Article 1 in Industrial Minerals by B. DUNSTAN, Chief Government Geologist (Publication No. 268, in Part) Queensland Geological Survey, Department of Mines, Brisbane 1920 In Queensland, however, the term embraced some of the metals as well as the non-metallic minerals proper. The lead furnished by Canada in this matter bore rapid fruit, and already the term 'Industrial Minerals' is widely used, not only throughout Canada but in the United States as well.

Jan 1, 1939

By Junior Santos

Kinross Paracatu started the operation of the new gold processing plant in the end of 2008, being composed by one SAG mill and two ball mills. During the first year of operation the plant had several problems related to stability and throughput capacity, mainly due to low grinding efficiency of the ball mills. In this period many actions were taken to maximize the throughput rate. Among the actions are reducing the size of balls in the mills, increasing the ball charge in the SAG mill, changing cyclone configuration and return of circulating load to SAG mill. With better stability of the circuit, the second stage of improvements has begun with the objective of increasing throughput rate and also reducing operation costs. Among the actions are the optimization of ball charge in the mills and a better operational control of cyclone parts. After two years of operation was obtained a significant increase in plant capacity, but still requires the addition of a third ball mill in order to maximize the use of SAG mill, which has spare capacity.

Jan 1, 2012

By S. Kivrak

The firms in construction industry could not sufficiently adapt the rapidly emerging information technologies in recent years into their corporate structures. Therefore, in an effort to further exploit the benefits of information technology (IT), integration of the experiences and backgrounds of construction industry and the advantages of IT, is one of the most open-ended fields for improvement in this industry. Utilization of IT in the construction sites will positively affect the efficiency, productivity, quality and health & safety issues in the construction sites thus the cost and completion time of the projects. Within this context, augmented reality technology, which brings a new perspective into IT, can be put into the service of construction industry. Augmented reality which has been designed to improve the services in many application domains such as school education, military warfare, military trainings, industrial maintenance, retail and medical, can be defined in the simplest form as augmenting the real world with information from the virtual world. The main aim of this study, which presents an overview of an ongoing project, is to develop an innovative method by making a construction worker, foreman, equipment operator or a site engineer watch a very comprehensive and informative animation which will enable the said staff to perform or supervise all the phases of the activity he or she is in charge for in a more efficient, productive, safer and qualified manner by means of smart glasses using augmented reality systems. In this respect, training material related with the activities in the construction sites will be prepared and with a well-fictionalized scenario, animations exhibiting all the phases and details regarding the related activity (e.g. masonry, formwork and rebar works etc.), method of statement, correct and incorrect applications in comparison-wise manner, will be produced. Therefore, the user will be able to reach the training material, method statements etc. in the animations about the activity he or she is in charge for, enabling him or her to figure out the work as prescribed in the specifications. Basic trainings about the system will be given to target group, i.e. construction workers, foremen, operators, site engineers and managers working in the construction sites to apply the system on sites after all the system was tested. After the testings, to determine the effectiveness of this system, semi-structured interviews and survey questionnaires will be conducted among the mentioned target group. Therefore, the potential benefits of this system to the construction industry can be determined. The main target of this study is to implement an efficient, thorough construction management by orienting the staff in the construction sites to perform efficient, safe and qualified works by means of smart glasses that use augmented reality. There are relatively few studies about the implementations of augmented reality technology in construction. The outputs to be attained in the end of the study have the potential of improvement of time, cost, quality and safety parameters by ensuring a qualified, safe, efficient and productive construction management via augmented reality technology in the construction industry.

Aug 1, 2013

By Jianwen Yang, Yucai Zhou, Yanhong Dong, Daixiong Chen

"The study of combined depressants for flotation separation of lead from copper has been carried out to solve the copper-lead separation problem. Test results show that the depressant of CMC (Carboxyl Methyl Cellulose) or sodium sulfite plays an important role on the selective depression of galena flotation. When the two reagents above are combined, the selective depression effect on galena is further enhanced. When the mass ratio of CMC to sodium sulfite is 1:4, galena was best depressed, with the lowest lead content in the copper concentrateClosed-circuit tests indicate that under a certain pH value of the slurry, with the best ratio of CMC to sodium sulfite as depressants, the copper concentrate with the grade of 28.23% copper and 4.12% lead is obtained, and the copper recovery is 84.87%; the lead concentrate with 68.12% lead and 0.86% copper is obtained, and the lead recovery reaches to 92.20%. An efficient separation of copper and lead is achieved with the combined depressants. INTRODUCTIONComplex copper-lead-zinc sulfide ore is abundant in China. With the rapid increase of mineral consumption, it has become one of the important sources to produce copper-lead-zinc metals. However, it is difficult to achieve effective separation of copper and lead, due to the complicated ore properties, such as fine dissemination, low copper grade, complex symbiotic relationship and similar floatability of copper and lead.Poisonous reagents of bichromate and cyanide are often used as depressants for copper lead separation. They have good separation efficiency, but pose serious pollution issues. As the environmental protection is becoming more and more important, it is a trend to replace traditional toxic reagents with new nontoxic efficient chemicals. Organic depressant FCLS studied by Liu has strong selectivity against galena, and does not depress chalcopyrite. A new type of galena depressant of CLS-01 discovered by Jin-lin Yang shows good results in the separation a mixed copper and lead concentrate. In addition, dextrin, chitosan and some other natural organic compounds (Drzymala, 2003; Huang, 2012; Qin, 2013) have also been studied to separate copper and lead."

Jan 1, 2016

Originally developed as a step change in ultrafine grinding efficiency, the IsaMill? has made inroads into conventional ball mill and tower mill mainstream grinding duties during the last 5 years - beginning with the Anglo Platinum mainstream grinding projects in South Africa. At the 2006 SAG Conference, plant testwork on the incorporation of IsaMill? technology into the McArthur River (Northern Territory, Australia) Pb/Zn primary grinding circuit was reported. The IsaMill? has now become an integral component of that circuit, treating up to 1mm top size feed and directly producing P80 45 µm rougher flotation feed. Two 1.1 MW IsaMills? are now used in this duty contributing to a 27% increase in overall plant throughput and a reduction in rougher feed size distribution. In this paper, we report on the current state of development and performance of the IsaMill? in the primary grinding duty at McArthur River and also consider future directions.

Jan 1, 2012