Search Documents

By Chas Kemsley

NO. 6 shaft at Dome Mines, Limited, is an internal shaft going down vertically from the sixteenth, or 2,000-ft., level to the twenty-ninth, or 4,000-ft., level, with loading station and sump below this. It is located approximately 4,600 feet east of No. 3 shaft, the latter being Dome's main shaft through which ail ore, men, and material are handled. The decision to sink this shaft was made in May, 1935, and work was commenced almost immediately. To reach the site of the new shaft, 3,100 feet of cross-cutting, and 1,400 feet of slashing to widen existing cross-cuts, was necessary. On account of the long haul and the large amount of material to be handled, trolley haulage was decided upon and installed as soon as possible to facilitate the removal of waste rock from the crosscut and other necessary excavations. Figure 1 shows a cross-section of the cross cut and the manner in which the trolley wire is supported and guarded. For hanging each individual cross-piece, two holes are drilled into the roof and filled with snug-fitting wooden plugs. Into these, %-in. ragged hanger bolts arc driven by means of a stoper. The bolts are of various lengths to allow for irregularities in the face of the rock, and they have sufficient thread to permit several inches of adjustment for proper alignment of the cross-pieces. These hangers are spaced at 8-ft. intervals except at the curves, where 5-ft. spacing is used. A 2 in. by 6 in. cedar plank is fastened to the cross-pieces directly over the centre of the track. To this the trolley-wire supports are bolted, and 1 in. by 10 in. cedar boards are nailed on each side to act as guards. Two power-supply cables, one telephone cable, and one .Y2-in. conduit lighting circuit are also supported on the trolley-wire hangers, as shown in Figure 1. A 20-in. ventilating pipe and a 10-in. air line are placed as shown, thus acting as a guard to prevent workmen from walking on the track.

Jan 1, 1938

By John Stoten

"The 1980s have proven extremely difficult years for many resource-based organizations. Mining companies have learned how to weather the negative effects of inevitable economic cycles. However, with some notable exceptions, such as gold mining companies, the mining industry has faced a broader and deeper round of cutbacks than any experienced since the 1930s. Downsizing has been a major issue for many mining companies as they have faced the need for dramatic staffing cost reductions in the recent past.The continuing current rapid rate of change in technology and the marketplace, coupled with increasing merger and acquisition activity, will provide an on-going need for some companies to face major reorganization. This inevitably will involve down-sizing activity in some instances.Given this scenario, it is worth reviewing the industry's past experiences to identify approaches and techniques that could prove of value in handling a future staff downsizing challenge. This paper is based upon a downsizing consultant's experiences with the mining industry and other sectors, and highlights what appear to be key staff reduction planning and process issues.Planning for DownsizingA review of companies' downsizing activities of the last few years reveals four key activity stages which need to be addressed to ensure a successful transition. These stages are:1. organization planning;2. developing cost reduction strategies;3. implementing downsizing; and4. building for the future.A business situation that is severe enough to require drastic staff cuts typically affects all aspects of a company's operations. Most mining companies have reviewed cost efficiencies in many operational areas. However, these reviews often have been short term in focus . As a result, some companies have experienced multiple downsizing; each event a response to an immediate economic threat. This has sometimes resulted in an unstable organizational environment, with severe stresses on staff morale and productivity.In the long term it is more efficient and less stressful to the organization to adopt a more comprehensive and longer-term strategy. Especially in capital intensive mining operations, it makes sense to review all areas of business activity, not just staffing."

Jan 1, 1989

By J. L. Feng, F. Zhang, S. K. Hu

"Cracking is one of the most serious damages in tunnel linings, which is often observed by in-situ inspection to tunnel engineering. It is difficult to better characterise for the deformations from continua to discontinua by the traditional continuum mechanics due to emerging of crack initiation, crack propagation, and coalescence, at several scales. In this paper, the process of failure that was from micro damage to macro crack in concrete tunnel linings under experimental load conditions, was quantitatively simulated by the combined finite-discrete element method (FDEM). Comparison of the simulating results with that obtained by the full-scale test of concrete lining under different loading conditions in the literature was respectively good agreed and shows that such FDEM technique is appropriate to model the continuousdiscontinuous problems. The present study indicates that the FDEM technique could be benefit to quantitatively evaluate the stability and damage level of tunnel lining system. INTRODUCTIONMost damage to tunnel linings is caused during the construction phase, which can emerge in a form of single macro cracks or even large-scale spalling. The cause of such damage is mostly the occurrence of, either impermissibly large contact stresses resulting from high thrust loads combined with production and installation tolerances in the segments resulting in a geometrical lack of fit (Maidl et al., 2012; Transportation Research Board, Basic Research and Emerging Technologies Related to Concrete Committee, 2006), or unallowable tensile/shear stresses appearing in the tunnel linings under complicated loading conditions (Ansell, 2010). Such a macro failure phenomenon may also be regarded to as a result of growth, coalescence, initiation of microcracks in tunnel linings due to the complicated loading action, and even potentially lead to an instability or collapse of the local or entire tunnel system. Much work has been devoted to investigate for the characters of micro and macro cracks, the influence factors of damage patterns, the settlement of a tunnel, the width, length and density of lining cracks, especially from classifiedly and qualitatively (Wang, 2010; Huang et al., 2013). However, the safety evaluation of tunnel is definitely required to not only inspect in situ, but further also quantify computing and analyzing for tunnel lining systems, so as to provide a global viewpoint of process of the tunnel deformation, which aims to help for subsequent decisions, e.g. controlling traffic flow or immediately repairing task. Additionally, the design of lining thickness and its structural analysis that is mostly determined by previous experience and similar construction examples is also needed to be improved."

Jan 1, 2015

By P. Condori

Palabora Mining Copper has a unique ore body composition which unlike other copper ore bodies has three main components in significant proportions; these are copper bearing ore, magnetite and dolerite. The high content of dolerite, a hard barren material, creates a high proportion of pebbles which normally are recycled back to the mill. This action increases the mill bearing pressure and power progressively until corrective actions are taken. A logical action to solve the pebbles generation would be to incorporate a pebble crusher. This in fact was done however two fundamental issues were encountered; the high content of magnetite and existence of a cyclone classification section. Due to the high content of magnetite, metal detectors have not been able to work efficiently to separate tramp metal which causes damage to the pebble crushers. The existence of cyclones in the circuit had a detrimental effect on the final product when the pebbles crusher was online producing coarse sandy material. Due to the difficulties in treating pebbles via conventional procedures and the unique Palabora ore composition and characteristics, sorting technology was investigated at laboratory and pilot scale. It was found that a combination of optical and electromagnetic sorting could efficiently separate dolerite from the copper bearing and magnetite ores. This paper reports the findings of the laboratory and pilot scale work performed and discusses the additional benefits to the circuit.

Jan 1, 2012

By V. Vakiloroaya

The paper aims at developing a hybrid solar-assisted air conditioner system for performance enhancement and energy efficiency improvement. To increase sub-cooling of the refrigerant at partial loads, we propose a new discharge bypass line together with an inline solenoid valve, installed after the compressor to regulate the mass flow rate of the refrigerant vapour passing through a hot water storage tank. For control design, a lumped parameter model is first developed to describe the dynamics of the system in an explicit form of input-output relationship. The system has been fully-instrumented to examine its performance under different operation conditions. The system model is then validated by extensive experimental tests. The predictions from the models exhibit a good coincidence with experimental results, judging by an RMS error less than 15%. Based on the obtained dynamic model, a linear quadratic regulator (LQR) is applied to optimize a cost function of the output errors and control efforts. The key challenge is to regulate the refrigerant temperature entering the condenser by controlling the valve opening. The design approach is then tested in a transient simulation tool to predict the system performance in transient conditions. The experimental results obtained from implementation with PLC demonstrate that the proposed system delivers higher system efficiency owing to the higher refrigeration effect in the direct expansion evaporator. Thus, the novel development is promising for improvement of energy efficiency, enhancement of the system performance while fulfilling the cooling demand. Consequently, between 25 and 43% of monthly electricity can be saved on average.

Aug 1, 2013

By C. S. Lord

"AbstractThe slow progress of conventional geological reconnaissance of the northern Canadian Shield during the past twenty years clearly indicates the need for a radically new field technique. Operation Keewatin, involving the use of helicopters as the traversing vehicles, was planned and executed by the Geological Survey of Canada in response to this requirement.About 57,000 square miles of District of Keewatin, N.W.T., were mapped during the 1952 field season in appropriate detail for publication at 1 inch to 8 miles. The Operation disclosed about 14,100 square miles of Precambrian sedimentary and volcanic rocks ranging in •age from Archaean to Late Proterozoic. About 7,700 square miles of this area are underlain by greenstone. This work was accomplished in a field season of 113 days, including the spring break-up. Routine aerial geological observations were made from two helicopters flying about 300 feet above the ground; these observations were checked by more than 1,700 landings and about an equal number of aerial observations from heights of less than 50 feet. Logistical support was •provided by a Norseman aircraft on skiis or floats. Combined helicopter and Norseman flying time was about 990 hours. More than 1-00 square miles were mapped per helicopter-hour, and about 815 square miles were examined each day that both helicopters operated. The reconnaissance cost about $207,000, or $3.63 per square mile mapped.As a result of this trial use of helicopters there is now available a reasonably proven method whereby an acceptable geological reconnaissance of the barren grounds of the Canadian .Shield within the Districts of Keewatin and Mackenzie might be completed within a decade. Thus, within a few years, it could place at the disposal of the prospecting and mining fraternity data which, by conventional methods, might not be made available to this generation. Due weight must be accorded this time factor when evaluating the aerial technique."

Jan 1, 1953

By R. Pakalnis, H. Miller, Madill. T.

"This paper describes a methodical approach to the estimation of the orientation and the magnitude of in-situ stresses. The study was performed at the Ruttan Mine, Sherritt Gordon Mines Ltd. , a 6,000 T.P.D. underground operation, located in northern Manitoba, Canada. It involves an initial estimate to be made based upon: structural interpretation • virgin stress measurements conducted in other areas (world wide, regional)The verification of the prevailing stress regime was made by conducting CSIRO hollow inclusion(1) overcoring measurements. The current cost for a virgin stress determination is about $7000 per measurement(2) and the difficulty encountered in attaining a good reading is high. This paper will describe the analytical procedures employed at Ruttan in evaluating the in-situ stress magnitude and orientation based on three overcore tests. It is proposed to perform an additional six measurements in order to verify the following results:Vertical stress = av (MPa) = 0.027 by depth (m)Major principal stress = o! """" 2.5 xav (340°/-20°)*Intermediate principal stress = a2 - 1.2xav (070°/0°)Minor principal stress = a3 """" o.8xov (160°/-70°)IntroductionThe Ruttan Mine of Sherritt Gordon Mines Ltd., a 6,000 T.P.D. underground operation, is located in northern Manitoba, Canada (Fig. I). The Ruttan copper-zinc orebody is a multi-lensed, steeply dipping (70 degrees) en-echelon deposit. Individual lenses have a maximum strike length of 350 m with widths varying from 7 m to 61 m. The mining method is o pen stoping with delayed backfilling and extends from surface to 860 m below surface."

Jan 1, 1985

By O. K. Mahabadi, A. Lisjak, B. S. A. Tatone, N. Vlachopoulos

"Numerical simulations are widely adopted in the design of several types of rock structures, including tunnels, caverns, rock cuts, and open pit and underground mines. In recent years, analyses based on the hybrid finite-discrete element method (FDEM) have been shown to provide a realistic representation of rock mass deformation and fracturing processes. To date, the FDEM approach has successfully yielded qualitative and quantitative results for several practical rock engineering applications, yet it has lacked the ability to consider the implementation of rock-reinforcement measures. Since rock reinforcement is often used in civil and mining applications to improve the strength and deformational behaviour of a rock mass, the ability to incorporate such features into FDEM analyses is essential to extend its applicability to a broader range of problems. The work presented in this paper represents an important first step towards developing a simulation tool that can be used for practical rock engineering applications, including the design of underground excavations and rock slopes.INTRODUCTIONRock support and reinforcement measures are often employed in civil and mining rock engineering projects in order to maintain or improve the strength and deformational behaviour of rock masses. The preferred type of reinforcement or support elements along with the preferred layout and timing of installation depend on the in-situ ground conditions, the nature of the rock mass and excavation method. Over the last two decades, numerical modelling has been increasingly used to design and attempt to optimize rock reinforcement and support systems. As such, most rock engineering-specific modelling software now offers various approaches for modelling different rock reinforcement and support elements."

Jan 1, 2015

By B. McHenry, A. E. Wraith, P. J. Mackey

The Wallaroo smelter on the Yorke Peninsula, South Australia commenced smelting operations in 1861 treating ores from the nearby Moonta and Kadina mines. The plant expanded and modernized on several occasions and was a leader in the successful introduction of new technology to improve operations. It operated continuously until 1923 when local mines became exhausted; in the closing stages of the 19th century it was the largest copper smelter in the world outside of those in Swansea, Wales. In 1892 a small electrolytic refinery was established at Wallaroo, the first in Australia, based on principles developed by Elkington at Pembrey, Wales in 1869. The Wallaroo refinery was specifically built to recover gold and silver from copper produced by smelting gold-containing feed materials shipped from Western Australia. This first venture into electrolytic refining was replaced in 1903 by a somewhat larger refinery which, although modest in size for its time, with a capacity of about 1000 tonnes of cathode copper per year, was very productive in precious metals. Anode copper was produced by an updated version of the reverberatory-based Welsh process until 1910 when barrel-type pneumatic converters were introduced based on American practice; subsequently, anodes were cast by tapping the precious-metals rich "bottoms" portion of converter copper as produced at about one-fifth into the copper blow. The present paper describes the Wallaroo refinery, its anode supply and products, supported by initial observations on a sample of a Wallaroo cathode held in the collection of the South Australia Museum, Adelaide SA, Australia. INTRODUCTION Australia ranked 6th in the world for copper mine production in 2018, with an output of 918,000 tonnes of mined copper, after Chile, Peru, Congo, China and the USA; about 40% of Australian mined copper was smelted in the country. Interestingly, the world ranking of Australia in mined copper has, with a few variations, remained about the same for more than 100 years – of interest, it was also the 6th largest country for copper production at 21,089 tonnes in 1899. At that time, all or most of the copper was smelted in the country (Mackey, 2016). Copper was first discovered in Australia in 1842 in South Australia not far from Adelaide; additional copper discoveries in the region soon followed. At first, copper ore was shipped to Swansea, Wales for smelting (Bampton, 2003). However, in addition to the long, 150 day one-way sea passage, it seems Welsh smelters preferred higher grade of ores – these aspects and likely a mood in the new colony to be independent of Swansea (Evans, 2014) evidently encouraged local smelting at the mine sites using small, Welsh-type reverberatory furnaces fired with hardwood as fuel and operated by Welsh and Cornish migrants. The first large copper smelter in Australia commenced in 1848 at Bremer, near Callington some 60 km east of Adelaide. With larger discoveries on Yorke Peninsula, the Wallaroo copper smelter at Wallaroo Bay on the west coast of the peninsula commenced operations in 1861 (Bell & McCarthy, 2008). Thus began one of the most successful, and in its day, one of the most advanced and innovative plants in Australia if not the world. In the late 1860s, it was considered one of the largest copper smelters in the world (Bell & McCarthy, 2008)

Jan 1, 2019

By F. Qi, T. Frišcic, C. Mottillo

"One of the principal goals of modern industry is to minimize the environmental impact and increase the materials- and energy-efficiency of transforming raw materials into valuable products. This paper will highlight our latest laboratory-scale research in low-energy, low-solvent reactivity of metal oxides and their conversion into popular metal-organic frameworks (MOFs), zeolitic imidazolate frameworks (e.g. Basolite® Z1200 component ZIF-8), and metallodrugs (e.g. bismuth subsalicylate, active component of Pepto-Bismol®). Mechanochemical ion- and liquid-assisted grinding (ILAG) and ""accelerated aging"" techniques will be presented, along with novel low-energy and solvent-free approaches, inspired by geological weathering processes, for converting metal oxides into metal-organic materials. INTRODUCTIONThe development of environmentally-friendly processes, which would in the same time be more materials- and energy-efficient than the existing ones, is one of the central concerns of modern chemical research. In that sense, the focus of the chemist has been mainly on the preparation of carbon-based organic molecules and adaptation of traditional organic synthesis to the recently delineated ideals of Green Chemistry. However, there is a growing realization within the chemistry community that significant energy, materials, and ecology-related benefits can be achieved and, indeed, targeted in the transformations of materials that are typically associated with inorganic chemistry and minerals processing. The principal aim of this highlight contribution is to illustrate how, through the use of approaches associated with solventfree chemistry and mechanochemistry (James et al., 2012), one can develop a clean and efficient system of chemical and materials transformations involving oxide precursors that normally belong to the realm of inorganic chemistry and mineral processing. In particular, this contribution will provide an overview of the recently developed mechanochemical and solvent-free reactivity of metal oxides towards small organic molecules. These mechanochemical reactions, including the methods of liquid-assisted grinding (LAG, Frišcic & Jones, 2009) and ion- and liquid-assisted grinding (ILAG, Frišcic, 2010), have so far provided a radically different means to construct advanced metal-organic materials (e.g. porous metal-organic frameworks, [MOFs] or metallodrugs) by rehabilitating metal oxides as precursors, eliminating the use of bulk organic solvents, and avoiding the use of high temperatures."

Jan 1, 2012

By Alan D. Brown

"Diesel-electric trucks are those that have some portion of the convention-al mechanical drive train replaced by electrical components. As larger and more powerful diesel engines appeared, the development of mechanical transmissions and related drive components failed to keep pace, and electrical generators and drive motors therefore came into use as an efficient means of transferring the mechanical energy of the engine to the driving wheels of the vehicle.The Berkeley Pit has been a major testing ground for the evolution of this type of truck. We now operate a haulage fleet consisting of conventional diesel trucks and two different types of diesel-electric trucks. There-fore, we have been able to obtain an interesting comparison of costs and performances between these three types of haulage units.In all phases of operation, the diesel-electric truck commands a favourable advantage over the conventional diesel truck, and represents a more efficient and less costly means of haulage. Nearly all manufacturers of heavy-duty trucks are now building, or have plans to build, such a truck."

Jan 1, 1966

By Carol A. Pilon

"IntroductionRECENTLY, the Saskatchewan Research Council (Saskatoon ) marked the completion of one of its coal-related projects with the publication of the Bibliography and Index of Coal in Saskatchewan and Adjoining Provinces and States, hereafter referred to as the Bibliography and Index of Coal. Over a two-year time period, literature was surveyed and indexed and bibliographic data were compiled using a computer-assisted information retrieval system called FAMULUS. The final publication contains 1150 bibliographic references, which are cross-referenced by six indices.The project was initiated in September 1974, in support of Saskatchewan's Coal Resources Evaluation Program , an ongoing research program sponsored by the Department of Energy, Mines and Resources (Ottawa) and the Province of Saskatchewan. This program places emphasis on such areas of concern as the occurrence of deposits, chemical and physical properties, calculation of reserves and computer-assisted applications for the evaluation of lignite resources in the Province. Attention is also given to aspects of geophysical exploration, mining conditions and economics, by-products and the transporting of lignite. These are the subject areas .covered by the Bibliography and Index of Coal.The over -all objectives of the literature indexing project may be enumerated as follows: (1) to build a specialized resource library by surveying established public and specialized libraries, and commercial data bases; (2) to enter library data into the FAMULUS information retrieval system, to be used to generate bibliographies and indexes, and to retrieve information by the use of specified searching techniques; (3) to make this library data available to interested persons."

Jan 1, 1977

By J. S. Edwards

The ISASMELT? process is recognized worldwide as a modem, flexible, environmentally-friendly and low capital cost smelting technology. Due to the inherent simplicity, and the advanced process control that has been developed, personnel become competent within weeks of being introduced to the ISASMELT? technology. This compares with the years required to become proficient with alternative technologies. Copper smelters in Australia, USA, India, China, Peru and Zambia have installed ISASMELT? technology under licence from Xstrata Technology. In the secondary copper business, plants in Belgium and Germany are processing copper and/or lead materials in ISASMELT? furnaces in a two stage process. In a single furnace smelting is followed by converting. Both plants have exceeded design capacities and are continuously improving their performance. The next evolutionary step for the technology is the implementation of the continuous copper converting process on a commercial scale. The present work describes the design status of the continuous converting process - ISACONVERT?.

Jan 1, 2007

By J. Visman

"Cyclone separators of different design are being used in increasing numbers in the coal industry of today. One recent addition, the Compound Water Cyclone, is finding application in the North American and Australian coal fields for the beneficiation of coking coals and for the reduction of sulphur and ash in steam coals. In this paper, the combination of specific-gravity separation, thickening, classification and water recovery are discussed. All of these operations can now be accomplished by means of cyclones that are effectively combined in circuits of compact design. In the layout of such integrated plants, three main sections are distinguished, namely: a Main Section for cleaning the plus-28-mesh fractions; an Effluent-Beneficiation Section for treating the minus-28-mesh fractions; and a Water-Recovery Section, where the wash water is reconditioned, and the fine solids are removed in a semi-solid state as slugs or pellets. Depending on the nature of the coal and the specifications of the purchaser, water-cyclone circuits can be flexibly combined with HM Cyclones and froth flotation, as well as with ancillary equipment for dewatering and drying."

Jan 1, 1968

By R. D. Brown

"""A matter of serious concern to the mining industry in British Columbia""; this comment reflects the attitude of the Mining Association of British Columbia toward the proposed new B.C. Mineral Royalties Act. The proposed legislation, introduced by the provincial government in February and now being debated by the legislature, combines a basic 5% royalty on the selling price, less approved p1ocessing and transpo1•tation costs, of minerals produced in B.C. with an ""excess"" royalty of 50% of any price increases over a predetetmined base. Government estimates project annual revenues of $20 million from the new royalty structure. The accuracy of these figures has been contested by the mining industry. Based on current world prices for copper the industry estimates that the provincial revenues from this mineral alone may run as high as $140 million in 1974 and $150 million in 1975. The Mining Association has warned that the new royalties “threaten to become confiscatory""."

Jan 1, 1974

By C. Peña, C. A. Zaror, M. Bustamante, M. Vega

The goal of this paper is to present the carbon footprint of Chilean cathodic copper, as a function of the electricity generation mix, ore grade, and process efficiency. Ore grades and acid leach-solvent extraction-electrowinning (LX-SX-EW) yields in the range 0.5-1.0% and 60-80%, respectively, were considered here. Additionally, electricity supply from two Chilean suppliers, SING (1.0 ton CO2/MWh) and SIC (0.4 ton CO2/MWh) was assessed. Simulation results show that oxide plants located in northern Chile, served by the SING network, feature carbon footprint within 4.3 - 11.4 MWh I ton cathodic copper, as compared with 3.5 - 9.3 MWh I ton copper in plants served by SIC. The footprint was found to increase as ore wade and process yields decrease.

Jan 1, 2011

By S. S. Sephton, Kirit C. Vyas, Melvin J. Greaves

Energy requirements for various pelletizing systems are considered from a fuel and power aspect, with the presentation of typical energy heat balance flow sheets. A partial calculation for the firing zone of a straight grate system is shown and a comparison of an actual measured and a theoretical-calculated heat balance for a grate-kiln is presented. The power used for each pelletizing system and future possible energy savings a1•e also reviewed.

Jan 1, 1976

By G. W. Poling

Sedimentation behaviour of siliceous mill tailings derived from a magnetite-chalcopyrite ore in fresh water, fresh water - sea water mixtures and full-salinity sea waters are compared. Results of batch settling tests are presented in the form of settling curves and solids flux curves. The addition of a few per cent of sea water markedly enhanced the zone sedimentation rate due to particle agglomeration caused by a reduction in zeta potential of the suspended solids. The presence of a small amount of residual, previously magnetized magnetite in the tailings also enhanced agglomeration and sedimentation. The significance of these results to submarine disposal of mill tailings is discussed.

Jan 1, 1973

By V. I. Ryaboy, V. P. Kretov, I. V. Ryaboy, E. D. Shepeta

This paper studies the features of known and newly synthesized dialkyldithiophosphates and reagents with thioamide groups when separating copper-containing and arsenic-containing minerals in the flotation of skarn-scheelite-sulphide ore at the Primorskaya concentration plant. The optimization of dialkyldithiophosphate collectors was based on the study of their surface activity at the liquid-gas interface and estimated hydrophobic abilities. The flotation experiments show that the selectivity of action of the reagent increases with an increase of its surface activity and a reduction of hydrophobic ability when separating chalcopyrite and arsenopyrite. IMA-225-5 was proposed as a more efficient dialkyldithiophosphate collector, which increases the recovery of copper by 2.8% compared to the industrially used collector IMA-I413. Selection of the optimal structure for reagents with thioamide groups (derivatives of thionocarbamate and thiourea) was carried out according to their acidity and the presence of hydrophilic particles in their structure. Calculations were performed depending on the pH of the solution of chalcopyrite to determine the optimum reagent sorption and to further optimize the structures of these reagents. The tests with reagents with thioamide groups show an increase in copper recovery by 3-4% together with a significant increase of arsenic content compared to IMA-225-5. As a stronger collector with thioamide groups, it was recommended to use sample 234, which belongs to the thiourea derivatives. IMA-225-5 was recommended for industrial tests at the Primorskaya concentration plant. Thus, this study has shown that using dialkyldithiophosphate is more appropriate if it is necessary to increase the selectivity of separation of copper-containing and arsenic-containing minerals, and using reagents with thioamide groups, or their combinations with dialkyldithiophosphates, is more appropriate if it is necessary to increase the recovery of copper or the quality of copper concentrate with less selectivity of the process.

Jan 1, 2016

By A. D. Mufch, G. P. Mitchell

"THE HARDY MINE of Falconbridge Nickel Mines Limited is located in Lot 9, Concession 1, Levack Township, Sudbury District, Ontario, 20 miles northwest of the city of Sudbury, and a mile west of the town of Levack. The ore deposit is one of the many nickel-copper sulphide bodies found on, or near, the lower contact of the well-known Sudbury norite-micropegmatite irruptive, and is one of a family of ore deposits which occur on the northwest rim of the irruptive.The property was acquired by purchase in 1935. In the same year a magnetometer survey along the footwall contact of the norite, which is covered by about 150 feet of glacial sands and clays, first indicated the location of the orebody. Drilling from 1935 to 1942 outlined the extent of the ore. Shaft sinking was commenced in the fall of 1951, and the mine is now approaching full production at a rate of about 300,000 tons per year.There are several major differences between the geology of the Levack area and the Falcon bridge area, which lies at the opposite extremity of the irruptive, 28 miles to the east. The purpose of this paper is to describe the essential features of the geology of the Levack area as seen in the Hardy mine, and to supplement the recent papers on other properties in the Sudbury area by Davidson (1), Lochhead (2), and Yates (3).General GeologyA recent review of the regional geology and an extensive bibliography of the Sudbury area can be found in the two papers by H. C. Cooke (4, 5). Some of the recent related references are: Jas. E. Thomson (6), E. M. Abraham (7), Franc. R. Joubin (8), W. G. Q. Johnstone (9)."

Jan 1, 1949