Search Documents

By D. E. Smith, M. K. Murthy

"The commercial potential of a silica-kaolin deposit that occurs on the banks of and close to the Missinaibi River in the District of Cochrane, Ontario, is under evaluation by Algocen Mines Limited. The geological features of the deposit, as well as its probable origin, are described. Mineralogical analysis of the deposit samples indicates that the principal minerals are quartz and kaolinite clay; it is estimated that about 20 per cent of the deposit is kaolin clay. The impurity minerals present are: a slightly magnetic Fe-Ti oxide mineral, goethite, muscovite mica, tour-maline, staurolite, anatase and zircon. Laboratory research studies are in progress to develop and evaluate suit-able methods for the separation of silica sand from kaolin. Results to date indicate that good-quality silica sand with an Fe,03 content in the range of 0.012 to 0.025 per cent can be produced. It appears that the clay portion can also be beneficiated to yield products meeting commercial requirements. It has been possible to beneficiate a portion of theetlay to obtain the particle size distribution now specified by industry. However, research is continuing to develop suitable separation and beneficiation methods which can produce kaolin clay meeting all the commercial requirements."

Jan 1, 1970

By M. Kucharski

The model of the Outokumpu direct-to-copper process deals with a steady-state process the parameters of which do not depend on time. To give a prediction for the process outcome, "a modified black box" method, which ignores most of the chemical reactions in the furnace, was used. This method takes input and output parameters into consideration. The presented model describes the Outokumpu direct-to blister process in the form of the set of linear equations which give mass and enthalpy balances as well as the distribution of elements between blister copper and slag. However, only major substances where quantities in the feed charge exceed a certain level (for example 0.5 kg/ lMg of smelted concentrate) are taken into consideration. Minor elements are distributed among slag and metal phases in a different way. Some of the equations are derived from distribution coefficients. The value of distribution coefficients can be calculated from plant production data.

Jan 1, 2007

By L. J. Cunningham

Introduction The property of Rouyn Merger Gold Mines, Limited, is in Rouyn and Joannès townships, Western Quebec, seven miles east of the town of Rouyn. Traversing it is the east-west trending Cadillac-Bouzan fault. Diamond drilling in 1944 and 1945 along a shear zone south of the fault indicated an ore deposit lying at the contact between sedimentary and volcanic rocks and dipping approximately 60° to the northwest. In the summer of 1945 it was decided to sink a shaft to investigate the indicated ore zone. In the immediate vicinity of the deposit, bed-rock is overlain by clay beds, in some places as much as 70 feet thick. Consequently, possible shaft sites were limited to those locations where overburden would not be excessive. The most favourable site was about 125 feet to the south of the ore zone as projected vertically from bed-rock to the surface. Accordingly, it was decided to sink the shaft at this point, with an inclination of 60° N. W., paralleling the dip of the ore zone.

Jan 1, 1948

By Peter A. Cain, John C. Folinsbee

"A 4-ft.-diameter shaft has been drilled to a depth of 2,790 ft. in strong, hard, basic Precambrian rocks at Lynn Lake Manitoba. This was done on the property of Sherritt Gordon Mines Limited for the purpose of ventilating and developing the ""N"" orebody, which is located approximately 4,000 ft. south of the Farley shaft.The drilling was done under contract by two drilling companies. Peter Bawden Drilling (1964) Limited drilled the initial 12:1,4-in. pilot hole to a depth of 3,000 ft. Shaft Drillers Limited of Canada then reamed the hole to 4 ft. in diameter to a depth of 2,790 ft. At this point, the reaming was stopped because of the difficulty in passing a change in direction in the line of the pilot hole. The hole was completed by driving a raise 200 ft. from the 3000 level to the bottom of the 4-ft. hole using an Alimak raise climber.Cuttings from the reaming operation were directed into the 12:1,4-in. pilot hole, where they fell to the 3000 level and were removed by a mucking machine and standard mine development cars.The elapsed time from the start of the pilot hole to the completion of the reaming operation was ten months, with an average advance of 279ft. per month. There was a two-month delay between the completion of the pilot hole and the start of the reaming operation.The 12:1,4-in. hole was drilled in an elapsed time of 45 days from the time of setting up the rig. The average advance per day was 66.8 ft.The reaming operation was done in an elapsed time of 194 days. A one-month delay required to repair damaged equipment left 163 days for the drilling and setting-up operation, for an advance per day of 17.1 ft."

Jan 1, 1966

By Jochen Petersen, Jean-Paul Franzidis, Allan Nesbitt

This study presents a method for the determination of intra-particle diffusivities in ion-exchange resins for the purposes of evaluating the state of resin degradation during service. The method uses a zero length column (ZLC) in a closed circuit with variable speed pump and reservoir. The intra-particle diffusion is determined from absorption data by using the Nernst-Plank approximation along with the ‘mass transfer factor’ - which is a product of the mass transfer coefficient (kf )and the concentration of the adsorbing ion in the liquid at the surface of the resin - in a computer algorithm fitting simulated curves to experimental data.. Through this approach the changed intra-particle diffusivity, of a gel-type acid resin, over a 1000 loading and elution cycles, is shown.

Jan 1, 2014

TRE ? worldwide leader in InSAR ? Spinoff of Polytechnic University of Milan ? Numerous patents for cutting edge technology (e.g. SqueeSAR?, PSInSAR?) ? Focus solely on InSAR with over 13 years experience ? ISO 9001 quality certification ? Powerful scalable parallel processor to handle all jobs What can InSAR provide for mining? An advanced suite of tools for monitoring ground deformation over mine sites: ? Deformation maps ? A dense network of measurement points ? Time series ? Cross sections of surface profile evolution

Aug 1, 2013

By Alan E. Cameron

WE assemble again today in this comfortable, hospitable Inn to begin this, the 58th, Meeting of our Society. It is just a year ago when last we met but that year was, probably, the most portentious year in the whole history of mankind. In that year, the German 'Atlantic Wall' was broached, the Rhine was crossed, and Germany, as a Nation, has ceased to be. The agony of Europe is over; convalescence may be, probably will be, slow. But blood no longer flows in Europe. Time will heal the sores, cover the scars, regenerate the industries, rebuild the cities, and re-establish the people. True, the war of all wars is not yet over. True, a bloody conflict remains . But, the power of the United Nations now converges on one target. The rain of blood will be heavy. We can hope the storm will be short. The sun is on the horizon. The light of peace 1s in the sky. What of that Peace? Are we ready for it? Have we a 'sure foundation ' for our future world? Are the footings under that foundation broad and substantial? Can we look forward with confidence to a lasting peace and a fruitful life? The United Nations, even as this is being written, are in conference in San Francisco, placing the footings, rearing the foundations for a world edifice. There are bickerings; there are jealousies. The world is tired, and a tired family always squabbles. We can, we must, believe that the decisions they make, the edifices they rear, will be better than anything we each could effect separately. It will be a compromise, probably; it will carry things that will hurt us, just as it will carry things that will hurt others. We can, we must, believe that the good of the whole is a greater good than the good of the part. Each Nation within the United Nations must sacrifice something, each part of each Nation must sacrifice something, each individual within each part of each nation must contribute something, if the whole is to be wholesome. Sacrifice and contribution must be the order of the day if the New World we are about to build is to be worth while. What of Nova Scotia? The world has travelled far in the last year; how far has Nova Scotia gone? Canada has preparations for the Peace under way; what has Nova Scotia done? Is Nova Scotia preparing counter measures for the sacrifices it must make? Is each of us ready to contribute his share?

Jan 1, 1945

By M. Barati, K. Ebrahimi-Nasrabadi, P. W. Scott

"The conversion of cryptocrystalline magnesite to caustic magnesia was studied experimentally at temperatures of 400–1,200°C and for calcination times of up to 8 h. A differential thermal analysis– thermal gravimetric analysis showed that decomposition begins at temperatures as low as 340°C and is completed at 600°C. Specific surface area, iodine adsorption number, crystallite size, and loss on ignition were measured to characterize the product quality. It was found that high-quality caustic calcined magnesia can be produced in a narrow temperature (600–650°C) and time range (1–4 h).RÉSUMÉ La conversion de magnésite cryptocristalline en magnésie caustique a été étudiée de manière expérimentale à des températures de 400 à 1200 °C et pour des temps de calcination atteignant 8 heures. Une analyse thermique différentielle – analyse thermique gravimétrique montre que la décomposition commence à des températures aussi basses que 340 °C et qu’elle est complète à 600 °C. La surface spécifique, l’indice d’adsorption de l’iode, la taille des cristaux et la perte au feu ont été mesurés afin de caractériser la qualité du produit. Il a été trouvé qu’une magnésie caustique calcinée de grande qualité peut être produite dans un petit écart de température (600 à 650 °C) et dans une période de temps variant entre 1 et 4 heures."

Jan 1, 2015

The Mineral Industry of Canada in 1951 Continuance of the remarkable, successive increases in the value -of Canada's mineral production, chief basis of the nation's post-war expansion, was one of the highlights of Canadian development in 1951, when, according to the preliminary estimate is-sued by the Dominion Bureau of Statistics and reported in the BULLETIN for February, 1952, mineral output for the year reached a new high of $1,228 millions. This marked an increase of 17.5 percent over the previous year, which was the first in which the billion dollar mark had been reached, and an increase of 143.7 per cent over 1946, when production was valued at approximately $503 millions. While higher prices for the principal base metals accounted for a large part of the 1951 increase, quantity gains were made by copper, nickel, zinc, asbestos. lead, cement, and strikingly important. by petroleum, the value of which exceeded for the first time that of coal production. Gold was an exception to the general trend, being lower in both quantity and value than in 1950. For the first time nickel .came within $9 millions of surpassing-gold as the leading mineral product. Metals and Fuels The value of all metals, estimated at $733 millions, was 18.7 per cent more than in the previous year. Nickel advanced 11 per cent in volume and 34 per cent in value. Copper was up 2.4 per cent in quantity and 21 per cent in value, zinc rose 6.6 per cent in quantity and 35 per cent in value, and although the volume of lead produced was lower by 8 per cent, its value increased by 17 per cent. The tonnage of iron ore was 31 per cent higher than in 1950.

Jan 1, 1952

By C Carbonneau

In order to successfully produce columbium pyrochlore concentrates, St. Lawrence Columbium and Metals Corporation had to face two principal problems met in several new operations but possibly made more acute than usual owing to the newness of the project. 1.-The ore is particularly complex, as it is made up of an elaborate intermingling of carbonates and discontinuous ultra-alkaline rock bodies of various ages and types in which no less than seventy mineral have been re-ported. Obvious petrographic or structural controls are lacking. Ore boundaries have to be defined on the basis of assay results and the determination of several minerals which occur in trace amounts. 2.-The pyrochlore concentrates produced had to com-ply with a set of stringent specifications. This fact, combined with the low Cb205 content of the ore, necessitated the use of a beneficiation process that would have to operate at a concentration ratio greater than 100:1. A brief description of the mill circuit is given. Mill stability was obtained through extensive mineralogical study of the mill feed coupled with close geological and engineering control of the mining operations.

Jan 1, 1965

By R. B. Ellestad

Introduction Lithium has been known since 1817, when it was discovered by the Swedish chemist, Arfvedson, while working in the laboratory of Berzelius on the chemical analysis of the mineral petalite, LiAl(Si205)2. Development of the chemistry of lithium proceeded slowly, following the early work of Davy, Gmelin, Bunsen, and Matthiessen. Approximately seventy years elapsed before lithium products assumed any commercial importance, and for a considerable period it was a' very minor industry. Their chief early use seems to have been in medicine, and in the production of lithiated water. Other more important uses were gradually discovered, and the industry has had a slow but steady growth. Chemistry Lithium is classified as an alkali metal, along with sodium, potassium, rubidium, and cæsium. Like these, it is a silvery-white metal, which can be cut with a knife; it is harder than sodium, but softer than lead" It is remarkable in having a density of only 0.53 gram per cubic centimeter, which makes it the lightest metal. On ignition in air, it burns intensely to form chiefly lithium monoxide, Li2O. Like the other alkali metals, lithium reacts vigorously with water to form hydrogen and lithium hydroxide. The later is a strong base, and reacts with acids to form salts. The salts of lithium are in general analogous to those of the -other alkalies, but many of them have unique properties. For example, lithium chloride and bromide are extremely hygroscopic, and have a very high water solubility. Lithium fluoride, phosphate, and carbonate, on the other hand, are all relatively insoluble, unlike the corresponding sodium and potassium compounds. In this instance, lithium exhibits its frequent tendency to resemble the alkaline-earth group of elements (calcium, strontium, and barium). Many of the special and valuable properties of lithium are related to the extremely small size of the lithium ion.

Jan 1, 1948

By Steven Hart

In September 2009, Newmont began the commissioning of a 3 stage crushing and milling circuit at its Boddington Gold Operation in Western Australia. The Boddington ore has been recognized as one of the hardest and most abrasive ores treated to date and this played a pivotal role in the selection of crushing and HPGR technology for this operation as opposed to the more conventional SABC circuit. This paper will examine the scale up from laboratory to pilot plant and full scale operation of the crushing circuit. There have been many challenges to overcome in the first 18 months of operation; however, the HPGRs have in general met design expectations and performance is expected to improve further with ongoing design changes

Jan 1, 2012

By B. F. Osborne

"A new sensor cannot be considered in isolation from the process in which it is utilized. This paper, describing an on-stream particle size analyzer, therefore gives considerable emphasis to the slurry handling techniques employed to ensure that the instrument is presented with a representative sample. A new sampler is described, which continuously abstracts a small, representative sample from a closed pipeline containing a flowing slurry. This sample is then diluted, thoroughly mixed and pumped to a head tank, from where a continuous stream is fed at a constant rate to the size analyzer. Data are presented to show that particle size segregation is minimal throughout this sampling and sample preparation. A continuous particle size analyzer based on a separation principle is described, and the basic parameters of size distributions, and how they relate to this particular instrument, are considered. Typical results are given. An electronic system is presented which accepts the basic sensor outputs, and converts these to a particle size signal suitable for process control. Finally, the use of an inplant computer to process the sensor signals to obtain a particle size signal is briefly considered."

Jan 1, 1972

By C. R. Larsen, R. G. Bradburn, A. L. Mular, B. C. Flintoff

"Following the acquisition of grinding- circuit data at Brenda Mines Limited for simulation purposes, various methods to mass balance the circuit were evaluated. Unfortunately, different answers were obtained for different balancing methods. A data-adjustment procedure was therefore developed. The procedure assumes that all ""best-fit"" criterion. A search is conducted with the minimum set of water masses and narrow size ranges of solids around the circuit (called search variables), which permit the computation of any of the measured data points. Search variables are used to calculate measured values for an objective function of the form: [ ] where W, is a weighting factor•, M1 is a measured value and M. is a corresponding . value calculated from search vanables. The best values of M, are those which minimize R. The above method is compared with others that have been utilized for mass balancing circuits."

Jan 1, 1976

By Douglas A. Grieg

THE EXCUSE for producing still another paper dealing with the oilfields of the Middle East is the overwhelming importance of this area to everyone, both inside and out of the oil industry. Figure 1 shows the area defined as the Middle East for the purpose of this paper. No description of what constitutes the Middle East is generally acceptable to everyone and, in fact, in many parts of the world it is referred to as "Western Asia". At the time ?the writer went to work as a geologist in the Middle East -this was in 1926 -there were just three known oilfields, namely, Hurghada in Egypt, Naft Khaneh in the Transferred Territories of Iraq, and Masjid-i-Sulai-man in Persia. Their combined producing rate at that time was around 100,000 barrels per day. Toda y, just thirty years later, some forty-two fields have been proven to exist, and a recent discovery in Syria -if commercial -may add one more to the list. Producing rates at the end of last year ( 1956) were approaching four million barrels per day. This sizable figure re presents nearly 23 per cent of the total Free World's production. What is more important still, something over 70 per cent of the Free World's proven oil reserves are known to exist in the subsoil of the Middle East.

Jan 1, 1957

By C. M. Anson

Introduction The prosperity of any country today is dependent upon the efficiency and growth of its primary steel industry. The ?march of the United States of America to its present commanding position in world affairs parallels the growth of its steel industry. The remarkable growth of that industry was possible only because bountiful providence endowed that country with adequate supplies of the raw materials necessary for steel making -coal and iron ore. If we accept this hypothesis, and surely we must, then to what extent can we envisage the future of our own country? This symposium deals with the most important of the raw materials required for steel making -iron ore. If we are blessed with a bountiful supply of iron ore, then surely a glorious future awaits only our taking advantage of that blessing. It is becoming increasingly evident that Canada has immense iron ore deposits. It is my privilege to make you acquainted with one of these, one that can only be classified as among the more important ore reserves in the world. I refer to the Wabana ore deposits in Newfoundland. Location These deposits lie under the floor? of Conception bay, off the east coast of Newfoundland. They consist of a series of beds which outcropped for a distance of about three miles on the northeastern shore of Bell Island, dipping at approximately 8° toward the northwest. This three-mile outcrop is the only key to the occurrence.

Jan 1, 1951

By Pizhi Zhao, Jingwei Zhao, Zhenshan Liu, Yiheng Cao

"A new Al-Mg-Si-Zn alloy designed for automotive outer panel was trial-produced with industrial procedure. The final product shows a strong planar anisotropy. X ray diffraction analysis shows such strong anisotropy is caused by the dominating cube texture component in the final product. The reason for such high cube texture component was investigated by tracing texture evolution starting from the hot roll slab. It is found that certain cube texture components already exists in the hot rolled slab. The density of cube texture component shows as a wavy change through the following1st cold rolling, inter-annealing, 2ndcold rolling and solution treatment. This study shows that the cold rolling in the laboratory can well represent the texture evolution during the industrial production. The results obtained by lab rolling hints that change of second cold rolling reduction has weak effect on the planar anisotropy, when the gauge of hot rolled slab and final sheet are fixed.INTRODUCTIONWith the rapid progress of light-weighting in the automotive industry, aluminum sheets get more and more application as closure panel and structure parts. Recently the dominating alloy for outer panel is 6xxx series, containing the main alloy elements Mg and Si. The popular gradesareAA6016,AA6111, AA6022, and AA6014. These alloys still cannot satisfy the various requirements from automotive manufacturers. Most suppliers of automotive aluminum sheets are developing their own specific grades according to the customer’s demand. To increase the baking response, anew Al-Mg-Si-Zn alloy was designed, concerning the high combination energy between Zn solutes and vacancies formed during the quenching stage of automotive sheet manufacture. This combination is helpful to the precipitation of ß”phase during the paint baking (Wang, 2015,2016; Yan, 2014).The plastic strain ratio (r value)is a key index of the formability of automotive body sheet. A high r value means a good formability. The r values in different directions can be used to evaluate the planar anisotropy of the metal sheets. The trial produced Al-Mg-Si-Zn sheet shows a strong planar anisotropy with respect to r values. Since the r value is tightly related with texture, the texture evolution from hot roll slab (HRS) to final T4P temper was analyzed with X ray diffraction (XRD) to find the reason for the high anisotropy. Besides, the cold rolling reduction (CRR) was varied in the laboratory to modify the texture distribution, i.e., the planar anisotropy."

Jan 1, 2018

By G. M. Hughes, R. W. Dunn

"AbstractCurrently installed an analogue instrumentation devices at Sherritt 's Ruttan Concentrator control. and/ or measure mill tonnages, grind, pH, density , some reagent and slurry flows, and cell levels. On-stream analysis is used to assay the main process streams. The history of development of process control is reviewed from startup to the present stage of selection of a process control computer. A pragmatic approach has been taken to process control to ensure compatibility with the needs and resources of Ruttan. Emphasis is made of the need to have the mill performing well from a mechanical and instrumentation point of view and to have opera tor acceptance of the computer through training. Plans for the computer phase to achieve these objectives are outlined.IntroductionTHE COPPER-ZINC OREBODY at Ruttan Lake was discovered by Sherritt exploration personnel in 1969 and by mid-1973 a 10,000-tpd mine and concentrator were in operation. After a typical startup period , the major mechanical problems in the crusher and concentrator have been resolved. Metallurgical performance is now up to standards forecast in the feasibility study.The cost of the original instrumentation installations, including an on- stream analyzer, was about one million dollars or 4% of the cost of the milling complex. Although there was no intention of using a process control computer until the plant was operating smoothly, it was understood that all instrumentation was compatible with .a computer, but this did not prove to be correct. This paper cover s the development of the instrumentation loops to date and the control strategies that will eventually be implemented through a process control computer."

Jan 1, 1977

By Kri Inwood

"IntroductionIn 1879, when the Dominion government initiated its controversial program of industrial promotion, iron smelting in Canada was limited to one company producing coke iron on the mainland of Nov a Scotia and three small charcoal blast furnaces in Quebec. There was no steel production. By the eve of the first great war, iron and steel were being produced in very large quantities, the companies active in 1879 had disappeared and new centres of integrated iron and rolled steel production at Hamilton, Sydney and Sault Ste. Marie had come to resemble the industry as we know it today.The most dramatic change was that at Sydney, Nova Scotia, where in the early 1900s, two steelmaking companies established works. The Sydney developments have been explained as the result of resource discovery and technical change. W.J. Donald, in his authoritative account of the Canadian iron and steel industry, observes:""The most rapid growth of the Canadian iron and steel industry has occured since 1897... The remarkable growth has been caused largely by the new conditions of the industry. The discovery and use of Newfoundland ores, together with the availability of Cape Breton coal, has made the Nova Scotia industry not only possible but profitable ... It is a safe conclusion that the Canadian industry would not have been an important one, had it not been for the discovery of the Michipicoten and especially the Wabana (Newfoundland) ores""Donald also argues that metallurgical progress had been necessary to render the ores valuable,""Newfoundland ores ... contain a considerable amount of phosphorus, and were made available for steel-making by recent inventions.""The purpose of this paper is to re-examine Donald's story. It will be argued that the origin of steel -making at Sydney is somewhat more complicated than Donald has indicated. The difficulty with Newfoundland ore extended beyond its phosphorus content and a resolution required more than the basic open hearth furnace identified by Donald. Moreover metallurgical change was only one of several developments necessary to induce industrial investment at Sydney. Surprisingly, however, the discovery of iron ore in the late nineteenth century does not appear to be part of the explanation."

Jan 1, 1983

By Charles Camsell

At the last annual meeting of this Institute the programme very properly was drawn up and carried out with the special object of calling attention to the Dominion's position and problems with regard to fuel supplies. That subject, always one of serious concern, was a source of considerable anxiety twelve months ago. It is still so, but in a decidedly less degree than at that time. So far as the immediate fuel situation is concerned our anxieties have been relieved. And I think we can safely say that such a consciousness of our difficulties and determination to overcome them, has been developed in the minds of our people that there will be no slackening of the offensive until a final solution is reached. In selecting a subject of major importance for the present occasion I have felt free to digress from the pressing problems of last year and to go back, for a starting point, to the presidential address of two years ago .. I do not, however, wish to enter the controversy that has developed as a result of that address, though in spite of my own failure to amass a fortune from participation in certain mining ventures, I am decidedly inclined to the optimistic view that Dr. Corless presented of the future of our mining industry. You will perhaps have observed that in its general wording the title of my paper bears a marked resemblance to that of that address. This simila1ity of titles is not accidental. It is intentional on my part.

Jan 1, 1924