Search Documents

By John C. Lyons

"The Wabana iron ore deposits occur as flat-dipping beds of oolitic hematite and chamosite, of Lower Ordovician age, which outcrop for 3 miles along the northwest coast of Bell Island, Conception Bay, Newfound-land, about 16 miles from St. John's.The deposits occur in three zones, Upper, Middle, and Lower beds, separated respectively by 30 feet and 215 feet of shale and sandstone. They are primary sediments laid down in a shallow tidal basin by the precipitating action of a marine environment on iron-rich fresh waters flowing into the basin.The ore-bearing zones, while of wide areal extent, are not uniform beds of hematite that can be mined wholesale. The action of waves and currents during sedimentation; the delta pattern, velocity, and transporting power of streams flowing into the basin; the contours and oscillations of the sea bottom on which the sediments were laid have all been fundamental in the emplacement of richer and thicker mineable sections, and of lean zones so intercalated with shale as to be unmineable.The preservation of the deposits is due to their location in the Conception Bay syncline and to a considerable upthrust of the country east of the bay in post-Ordovician time.The hematite deposits were first recognized as such in 1892, and soon after were acquired by the Nova Scotia Steel and Coal Co. They are now being mined by Dominion Wabana Iron Ore, Limfred, a wholly owned subsidiary of the Dominion Steel and Coal Corporation, Limited. Production started in 1895, and up to the end of 1955 totaled 58,588,516 long tons of hematite ore, having an average dry analysis of about 51 5 per cent iron, 11 8 per cent silica, 0·9 per cent phosphorus, and l ·5 per cent moisture. About 40 per cent of the total tonnage mined has come from surface stripping and on-shore mines. These areas have now been almost completely depleted, and operations are confined to submarine mines extending for two miles off shore under the waters of Conception Bay. Three sub-marine slopes are currently in operation, Nos. 3 and 4 working in the Lower Bed and No. 6 in the Middle Bed. A general picture of the workings is shown in isometric projection in Figure 1. Submarine mining has been entirely by the room-and-pillar method, with an extraction of 60 per cent. The deepest workings, at a vertical depth of 1,850 feet below sea-level, have a rock cover of about 1,500 feet. No mining is done in areas where the rock cover is less than 200 feet. To date mining has explored six square miles of a potential area that may exceed 50 square miles."

Jan 1, 1949

By Robert B. Parsons

"The tax reform process marches on. The December 16, 1987 measures tabled by Finance Minister Michael Wilson represent one more step toward the objective of total reform of Canada's income and sales taxes. While the income tax changes are taking shape, much work still needs to be done on the sales tax side of the coin.IntroductionOn December 16, 1987 Finance Minister Michael Wilson tabled measures to implement the changes to Canada's income tax system that were proposed in the June 18, 1987 White Paper on Tax Reform. The measures were set out in a Notice of Ways and Means Motion; draft legislation relating to preferred shares, research and development expenditures; and draft regulations regarding capital cost allowance, certified films, flow-through shares, and the resource sector. The reaction of the government to the recommendations made by the Finance and Economic Affairs Committee Report on Tax Reform (the Blenkarn Committee), the Report of the Standing Senate Committee on Banking, Trade and Commerce and through consultations with interested groups and organizations, business, labour and individual Canadians is set out in a booklet of supplementary information.The basic features of the reformed income tax system set out in the White Paper remain. However, a number of significant changes have been incorporated in the Notice of Ways and Means Motion and other material. The following comments address those area s where changes have been made to the original White Paper proposals."

Jan 1, 1988

By A. H. Anderson

THE travelling grate coking process was developed by Shawinigan Chemicals, Limited, at their Shawinigan Falls plant. The first production unit went into operation a month prior to the outbreak of the war. Since then a substantial part of the coke used in the manufacture of calcium carbide has been produced by this process. In the following will be given a short account of the development work, a description of the process and the equipment, a discussion of the properties of the coke, the economics of the process and its future possibilities. EXPERIMENTAL WORK The carbide industry is a large consumer of coke, one ton of commercial carbide requiring for its production 1,200 lb. This coke must meet certain specifications in order to be acceptable. It should have a low ash content, preferably below 8 per cent, and the sulphur and phosphorus content must not be above specified limits. The size of the coke is also important. If it is too large it has to be crushed before it can be used in the furnaces, and if it is too fine it may have to be screened and briquetted. In addition, it must be dry. Although it was generally possible to purchase coke, including petroleum coke, and coke fines, in the quantities required, it became increasingly more difficult as time went on to obtain coke of a suitable quality at an attractive price. It was therefore natural for us to look to coal carbonization as a means of basing the supply of the fundamental raw material for carbide manufacture on something more solid than the shifting conditions of the coke market.

Jan 1, 1944

By John C. Robbins

A new technique for the determination of trace levels of uranium in solution has been developed. A compact laser emits short, but intense, ultraviolet pulses to excite the green fluorescence of a uranyl-complex formed by the addition of a proprietary reagent to the sample. Organic species present in most natural waters also fluoresce quite intensely, but their emission does not last appreciably longer than the excitation pulse, in contrast to the relatively long persistence of the uranyl fluorescence . Electronic 'gating' is employed to separate the long-lived contribution, rejecting substantially the organic emission. Results using the laser fluorescence method on many sets of natural waters of various origins have been compared against corresponding values generated by independent laboratories. Correlation has been generally good over a range from less than 0.1 to more than 100 ppb U. Solid samples have also been analyzed after extraction of the uranium into solution. Accuracies adequate for most exploration purposes have been achieved, but further work is required to determine effects of interferences in samples with complex matrices. The transport and deposition of uranium in natural waters is controlled by the organic and inorganic chemistry of the waters involved. It is suggested that interpretation of very low uranium levels will be aided by additional measurements of conductivity and organic content, with subsequent statistical treatment.

Jan 1, 1978

By Shintaro Takamiya, Kazunari Yoshida

"Recently, small sized micro-needles for medical are required more frequently by patients. The biggest reason is that it presents great burden on the patients, due to the size of the needle injection. People need to use a very small needle to lower the pain, but the downfall is that it makes them more expensive due to their complicated manufacturing method. Therefore, we need to fabricate a needle by wire-drawing to decrease its price. Tube-drawing is beneficial for its production value; however, in conventional tube-drawing it is difficult of control the wall thickness of the tube and makes it 1mmor lower in diameter. That is why, we propose fluid-mandrel drawing for new tube drawing. This method allows fabrication of a fine tube by using the pressure of the fluid in the tube. In this research, the goal is the fabrication of a fine tube by fluid-mandrel drawing and its evaluation. Finally, the fabrication of a fine tube by fluid-mandrel drawing was conducted and in result a tube with a diameter of 0.2mm, high strength and thin wall and fine inner surface was drawn, which can be used as a lesser pain micro-needle.INTRODUCTIONThe main manufacturing method of the current medical needles is roll forming. With this method, it is difficult to make a tube with a diameter lower than 1mm. Deep drawing has been proposed and used as method to further reduce the diameter, but this method is costly and the injection needle obtained by this method is several times more expensive.Therefore, we need to obtain a fine medical needle by drawing process that can be mass-produced and inexpensively manufactured. However, with the conventional drawing process, it is not possible to obtain a syringe needle with a reduced diameter easily, that is why, a fluid-mandrel drawing has been proposed which can reduce the diameter without damaging the inner surface. The methodology of the method is, a fluid is filled in the sealed tube and the pressure inside the tube during drawing is responsible for the good inner surface and wall thickness. It is also expected that the fluid can be easily discarded and that the tube can be manufactured on a long scale."

Jan 1, 2017

By M. B. B. Research Council of Alberta Crockford

Introduction Kootenay strata of Lower Cretaceous age contain much of the highest rank coal produced in Alberta. These strata outcrop in the foothills and mountains of southwestern Alberta and southeastern British Columbia, and the economic value of the coal seams contained in them was evident to the earliest explorers, who refer co them in their journals. Lacer, investigation of the .coal measures was undertaken by prospectors and by a succession of geologists, most of whom were in the employ of the Federal government, but some acted for private interests. Surveys by these men proved chat foothills and mountain regions hold immense quantities of high-grade coal within easy reach of transportation facilities, and their conclusions have accelerated the development of the coal-mining industry m Alberta. Among geologists who have contributed much to our knowledge of the region are J. M. Dawson, G. M. Dawson, R. C. McConnell, D. B. Dowling, J. D. Mackenzie, B. Rose, J. R. Marshall, B. Rose, J. R. Marshall, B. R. McKay, J. A. Allan, and J. L. Carr. The present paper is to a great extent a compilation of the work of the above men and of several others who have investigated the area lying between Bow river and Crowsnest pass. Space does not permit a list of all the sources of information so chat only chose of prime importance are given in the text. Data for the map and ?cross-sections of Figure 1 were taken from the following published maps of the Geological Survey of Canada: Cascade Coal Basin, Pub. 933; Canmore, Maps 322 and 323; Upper Elk River and Upper Highwood Rivers, Pub. l980; Blairmore, Pub. 1584; Southfork Coal Area Map l03A; and of the Research Council of Alberta: Highwood-Elbow Area, Map 20; and Ribbon Creek Area, Map 21. In some cases, the cross-sections have been simplified or otherwise altered, and for these revisions the writer cakes full responsibility. The stratigraphic sections of Figure 2 have been taken from published reports of the above mentioned organizations. The area covered in this paper is shown in Figure l. It is wholly within Alberta, and reaches from township 5 to township 27 and from range 1 co range 11, west of the fifth meridian. Its location is about fifty miles west of both Calgary and Lethbridge. Topography of the area ranges from foothill on the east to mountainous on the west. In this paper' the foothill region is considered to be chat which lies immediately east of the most easterly mountain ranges, such as Livingstone and Highwood. There are two principal coal mining districts in the area, one served by the main line of the Canadian ?Pacific railway and centring about Canmore, the other by a branch line of che same railway and centring about Bellevue, Blairmore, and Coleman.

Jan 1, 1949

By Yang Shuxin, Guo Qiliang, He Ping, Lu Lizhi, Yao Rui

"We combined stepwise regression and constrained regression statistical method to obtain the best boundary conditions for the calculation of in-situ stress field in Wushaoling tunnel using finite element method. Our numerical results reveal that: the main geologic factors contributing to the initial background stress are gravity and tectonics; the principal stress values would drop in fault zones; the angle between the maximal horizontal stress and the axis of Wushaoling tunnel is acute; Wushaoling tunnel tends to become stable when this tunnel has 2:1 ratio of the height to its width; the possibility of rock-burst exists under high stress.INTRODUCTIONStress state of engineering region is an important factor affecting the stability of project. Geological disasters in the project area are closely related to their stress environment. Wushaoling tunnel which is 20,050 meters long, lying along Lanzhou-Wuwei segment of Lan-Xin Railway in China, is the key project of Lan-Wu double-track railway. The region surrounding this tunnel is under a high stress environment. Accurate identification of the stress environment of the engineering area and the interaction between geomaterials and geotechnical engineering construction holds significant scientific and practical value for engineering design, construction, and operation.Many scholars explored and discussed the present-day tectonic stress through investigations of tectonic evolution history (Ding, & Lu, 1986), crustal deformation (Zoback, 1992), focal mechanisms (Yang et al., 2003, Xie, Cui, & Zhao, 2004), and so forth. However, the above methods would only provide the approximate direction of the principal stress in a broad region, and could not give the absolute stress values. In-situ stress measurement is one of the primary means to directly gauge the current crustal stress. However, in-situ stress measurement can only be applied in small number limited by measurement conditions."

Jan 1, 2015

By Jamie W. Pardy

The objective of the Canadian International Development Agency program is to facilitate the efforts of the people of developing countries to achieve self-sustainable economic and social development in accordance with their needs and environment. The British Columbia Ministry of Energy and Mines (BCMEM) is the executing agency for the four-year Peru Minerals and Metals Public Sector Assistance Project which began in December 1998. The primary beneficiary is the Ministerio de Energía y Minas del Peru (PMEM). The project is designed to address mine health & safety, environmental management and mineral resource information. Project activities currently underway include joint development of: an inspection system, a mine rescue system, an enhanced and e-Commerce capable mineral information website, environmental guidelines for industry and standardized ministry evaluation criteria for environmental impact assessments and closure plans. In addition, reports on management options for mineral concentrate transportation, storage and handling, and on mine reclamation security policy have been delivered at workshops.

May 1, 2001

By Limao Zhang

This paper presents a BIM-based Risk Identification Expert System (B-RIES) for metro construction, composed of three main built-in subsystems: BIM extraction, knowledge base management, and risk identification subsystems. The engineering parameter information related to risk factors is extracted from the BIM of a specific project where the IFC standard plays a bridge role between the BIM data and metro construction safety risks. An integrated knowledge base, consisting of fact base, rule base and case base, is established to systematize the fragmented explicit and tacit knowledge. A hybrid inference approach, with case-based reasoning and rule-based reasoning included, is developed to improve the flexibility and comprehensiveness of the system reasoning capacity. During the safety risk identification process, B-RIES is able to improve the inefficiencies in engineering information extraction, reduce the dependence on domain experts, and facilitate knowledge sharing and communication among dispersed clients and domain experts. A typical safety hazard identification in the Mingdu station, located in the Wuhan Metro Line Two, is presented in a case study. The results demonstrate the feasibility of B-RIES, and its application potential. B-RIES can be used as a decision support tool to provide guidelines for safety management in metro construction, and thus increase the likelihood of a successful project in a complex environment.

Aug 1, 2013

"The pressure leaching of alkali-pretreated limonitic laterite ore in nitric acid was studied. The optimal leaching conditions are as follows: leaching temperature of 458 K, initial nitric acid of 2.44 mol/L, leaching time of 60 min, liquid to solid ratio of 2:1 mL/g, agitation speed of 500 RPM. Under the above conditions, the extraction of nickel and cobalt can be achieved as approximate 95% and 80% respectively while that of iron is as lower as 1%. The leaching residue containing 70% of iron in the form of hematite and trace amount of chromium is suitable as the raw material for iron-making. The nitric acid in the leaching solution can be regenerated and further recycled to leach. INTRODUCTIONIt has been estimated that 60%-70% of the world land-based nickel resources presented in nickel laterites containing 130 million tons of nickel although these only accounted for about 42% of the world nickel production (Sudol, 2005; Luo et al., 2010). The nickel resource of laterite has not yet been fully utilized. Due to the increasing global demand of nickel and the declining global reserves of nickel sulphides, there is an increasing focus on the processing of the huge reserves of laterite ores today. Nickel laterite ores can be simply divided into two types, namely, silicate-rich and limonite. The former can be treated effectively by pyrometallurgical process in which the ferronickel product or nickel/iron sulphide matte is produced (Monhemius, 1987). The limonitic laterite is rich in iron in the form of goethite which is the main nickel-bearing mineral and usually contains cobalt associated with a manganese phase (Chang et al., 2010; Georgiou and Papangelakis, 2004). The limonitic laterite is usually processed by hydrometallurgical methods, such as atmosphere acid leaching (AL) (Xu et al., 2005; McDonald and Whittington, 2008), high pressure acid leaching (HPAL) (Chou et al., 1977; Georgiou and Papangelakis, 1998; Rubisov et al., 2000; Whittington and Muir, 2000) and reductive roasting-ammonia leaching (Caron Process) (Whittington and Muir, 2000; Valix and Cheung, 2002). The AL process can proceed at lower temperature, thus the operation costs may be very low. But two biggest problems associate with the AL process, namely, the slow rates of nickel extraction and potentially the significant amount of impurities such as iron and aluminum in the leaching solutions, which hampers the wide application of the AL process. The Caron Process uses the pyrometallurgical and hydrometallurgical methods together to obtain the metallic values, but the overall metal recovery is relatively low, especially for cobalt. In recent years, the environment-friendly process of HPAL has become increasingly important because it is most suitable for low-grade ores and leads to high extraction of the valuables. However, the HPAL process needs a much higher temperature and pressure (503-533 K, 4-5 MPa) to maintain a relatively fast leaching rates, which results in higher operation costs. Moreover, another serious problem of scale formation in autoclaves occurs in the HPAL process, for example, in Moa Bay, up to 20 cm scale may build up resulting in 5 days descale downtime per month. In addition, the iron residues cannot be utilized for ironmaking due to the presence of high content chromium (Ema and Harada, 1987; Owada and Harada, 1987; Takagi and Furui, 1987)."

Jan 1, 2012

By N Robb

This paper gives an account of the laboratory testing, plant testing and final inclusion of the two-stage sulphuric acid leaching process in the Milliken mill. Operational results for September, 1962, are presented, showing a uranium extraction of 95.5 per cent, with a saving of some 16 lbs. of 100 per cent H~S04 and some 9 lbs. of lime per ton milled. Methods for effecting further improvements in the process are indicated. HISTORY P RIOR to the incorporation of two-stage leaching, the process for the treatment of uranium ores at Milliken consisted of a single-stage sulphuric acid leach, followed by a solution recovery step involving washing in thickeners and two-stage filtration. The thickener overflow solution was subsequently concentrated and purified by ion exchange, and the uranium was recovered, by two-stage precipitation, as ammonium diuranate. Figure I illustrates this flowsheet. For satisfactory extraction of uranium from the. Milliken ore, a high residual acidity, of the order of 40 grams per litre of free acid in the discharge solution, must be

Jan 1, 1963

By Bunting S. Crocker

This paper reviews the trends in the past two years in autogenous grinding throughout the world. It covers rock grinding in South Africa, Sweden, Canada, the United States, Finland and Germany. To properly orient the discussion on this subject, the paper attempts to define and classify the scope of autogenous comminution. As this is a relatively new subject, there is often considerable confusion regarding the various practices, which sometimes differ widely. By clarifying the types and forms, we hope to help clear up this con-fusion. Autogenous grinding is being carried out, throughout the world, either in mills grinding in water or solution or in dry mills using air classification to remove the finished material. The wet grinding, particularly, can be divided into: (1) (2) (3) Primary autogenous grinding, or "run-of-mine" grinding. Secondary autogenous grinding or semi-autogenous grinding or rock pebble grinding. Combination processes. -This covers plants in which pebbles made in the primary mill are re-moved and used as grinding media for fine grinding in secondary mills.

Jan 1, 1963

By S. P. Chong, N. C. Shih, G. A. Turner

Fine powders, with the bulk of the particle diameters Jess than 10 microns, were aerated so that each particle was, on the average, separated from its neighbours by 1.3 to 2 mean diameters. In this state, measurements were made of the viscosity and settling rate of the powder, and the interfacial tension between it and a moist pellet. From the viscosity measurements, qualitative analogies are drawn between the behaviour of the aerated powder and that of a dense gas near its critical point.

Jan 1, 1970

By John Vergunst

"This paper traces the development of Ontario 's cap lamp standard. Over the years, numerous Coroner's Juries investigating fatal mine accidents have made recommendations with respect to underground lighting. As well, recommendations to improve mine lighting have been made by two Commissions, investigating mine safety in Ontario.During the past few years, the performance of any cap lamp worn by miners involved in serious accidents, have been measured by the Mining Heal/h and Safety Branch. Large variations in light output were found between and among cap lamp types. These variations have been attributed to the lack of quality control on the bulbs, design of the cap lamp head piece and in some cases, poor maintenance.In 1986, a series of underground tests were conducted to establish the minimum light output from cap lamps required to visually identify loose ground. The results of these tests indicated that a cap lamp should produce a minimum peak illuminance of 1500 lux measured at 1.2 metres from the light source. On May 30, 1987, Ontario became the first province in Canada to legislate the minimum amount of light required to visually assess ground conditions. INTRODUCTIONPoor lighting has been identified as a factor which can contribute to mining accidents. Over the past decade, several Coroner's Juries as a result of inquests into mining fatalities, have recommended improved lighting in mines.The Joint Federal-Provincial Inquiry Commission into Safety of Mines and Mining Plants in Ontario, was appointed to report upon the adequacy of existing arrangements and practice s that may affect safety. This Commission completed their report in April 1981, and recommended that inadequate lighting be investigated as a possible cause of all reportable underground accidents, and that a comprehensive research programinto mine lighting be undertaken.In response to the first recommendation, the Mining Health and Safety Branch of the Ministry of Labour, hereafter referred to as the Branch, initiated a program to measure lighting levels in all fatal accident investigations where inadequate lighting was a possible factor."

Jan 1, 1989

By T. A. Utigard, S. Pedler

Ilmenite from the Everett deposit in Quebec was characterized both chemically and mineralogically. The sample investigated contained the following main components: 40% Fe2O3, 21% TiO2 and 21% SiO2. The ilmenite grains contained about 20 to 25% hematite intergrown blades, with widths ranging from 2 to 30 \u03bcm. Crushing the sample to less than 0.85 mm led to significant liberation of the ilmenite from the gangue minerals. Gravity separation followed by magnetic separation of this size fraction led to a TiO2 concentrate grading of about 30% TiO2, with a recovery of 94%.

Jan 1, 2010

By R. H. Knudsen

"In view of the chronic overcapacity problem in the world potash industry and Saskatchewan's recent emergence as a major producer, the long-term outlook for potash productive capacity and consumption is of importance and interest to both the Saskatchewan Government and the potash industry. This paper is based on a report recently published by the Saskatchewan Department of Mineral Resources on projected world potash productive capacity and consumption for the ten-year period 1970 to 1980. Potash productive capacity and consumption are estimated on a country and regional basis and projected annually to 1980. Tables and graphs are included which summarize projected capacity and consumption for the period and illustrate the impact of Saskatchewan's capacity upon the North American and world potash industries."

Jan 1, 1973

By D. C. R. Espinosa, P. Aliprandini, J. A. S. Tenório, M. M. Jiménez Correa

"Nickel and cobalt are the main value metals in nickel laterite ore. Cyanex 272 is an extractant used to separate nickel from cobalt present in leach solutions. Previous studies demonstrated the extraction of cobalt, magnesium and manganese at pH 5 using Cyanex 272 as extractant, while nickel remained in aqueous solution. However, it is difficult to separate cobalt from a solution containing magnesium and manganese. One possibility to change the metals’ behavior during the solvent extraction process is to change the mixture of extractants used. In order to study the solvent extraction of cobalt from a solution containing manganese, magnesium and nickel, a mixture of two extractants was investigated. Cyanex 272 (CY) and Versatic 10 (VC) were selected as extractants in the organic phase. The extractant concentrations used were: 20% CY; 15% CY, 5% VC; 10% CY, 10% VC; 5% CY, 15% VC; and 20% VC. In all cases, kerosene was used as a diluent, at 80 vol%. The synthetic leach solution used in this study was prepared according to the composition of a typical nickel laterite leach solution. The pH value of the solution used was 5, and the aqueous/organic ratio used in solvent extraction testwork was 1/1. The study has shown that the composition of the organic extractant mixture did not increase cobalt separation.INTRODUCTION Sulfide and laterite deposits are the main sources of nickel. However, production from nickel sulfide ores has been decreasing over the years, relatively speaking, increasing the focus on the exploitation of laterite nickel ores (McDonald & Whittington, 2008). Laterite ore deposits are found in tropical and subtropical regions. A characteristic of laterite ores is the presence of a complex and heterogeneous mixture of metals (Crundwell, Moats, Ramachandran, Robinson, & Davenport, 2011; Georgiou & Papangelakis, 1998; Gupta, 2003; Kesler & Simon, 2015; Moskalyk & Alfantazi, 2002; Oliveira, 1990). Nickel concentrations in laterite ores are typically 1–2% (Dalvi, Bacon, & Osborne, 2004)."

Jan 1, 2017

By Graham Sim

Agenda ?The Water Challenge ?Examples from Three Case Studies ?Mine Drainage, 99% recovery ?Mine Drainage, 80% recovery ?Road Dust Control ?Technology Development ? Conclusion Global water challenges Assuring sustainable quantity Improving water quality Reducing energy consumption

May 1, 2011

By Mike Dry, Mani Manimaran, Mykolas Gladkovas, Mariam Melashvili, Chris Fleming

Development of a new hydrometallurgical flowsheet requires quantitative description and optimisation of all chemical processes in each step in the process, as well as mass and energy balances across a fully integrated circuit incorporating all the unit operations. This paper covers steps leading to early modelling of a gold processing plant based on a bromine/bromide lixiviant. Research conducted at SGS Lakefield in collaboration with Albemarle provided the data that were used in the development of this model. A previous investigation in this series described the leaching behaviour of various mineral types in Stabilized Bromine reagent. This paper is concerned with the gold recovery operations associated with a conceptual bromine leaching process. The recovery of gold by different types of resin and activated carbon was studied, along with various methods of stripping the gold from the extractant. The circuit is closed by electrolysing the spent leach liquor to oxidize some of the contained bromide back to bromine that would allow recycling the regenerated leach solution back to the leach step in the process.

Jan 1, 2015

By John S. Stevenson

ZEBALLOS is a relatively new mining camp. It is on the west coast of Vancouver island, approximately 195 nautical miles northwestward from Victoria. Previous to 1934, a small amount of placer gold had been recovered from the Zeballos river and tributary creeks. However, it was not until the winter of 1934-35, when shipments of high-grade gold ore were made from the property of the White Star Gold Mines, Limited, that lode gold mining really began. Since then, several new mines and many promising prospects have been found. Milling in standard sized mills only commenced late in 1938, when the 75-ton mill of Privateer Mines, Limited, and the 50-ton mill of Spud Valley Gold Mines, limited, were first turned over. The most striking feature of the camp is the high-grade quality of the ore as usually mined. At one property, the ore along a drift 650 feet long has ranged from 5.8 ounces per ton to 17.5 ounces, over average vein-widths ranging from 8.3 inches to 14.5 inches in selected blocks along the drift. One . high-grade shipment of 196.6 pounds of ore from the same property contained 142.877 ounces of gold. The present paper deals only with that part of the area in which mining operations are most active, namely the main Zeballos River valley and its tributaries, Spud and Goldvalley creeks. During the summer of 1938, prospecting was carried on beyond this circumscribed area. The geology and early developments in the area have been described in the following reports: (1) CLOTHIER, G. A., Annual Report of the British Columbia Minister of Mines, 1929, p. 376; 1930, p. 441; 1932, p. 205; and 1933, pp. 252-254. (2) GuNNING, H. C., Geological Survey of Canada, Summary Report, 1932, Part A-II, pp. 29-50, Zebaltos River Area, Vancouver Island, B.C. (3) STEVENSON, John S., Annual Report of the British Columbia Min-ister of Mines, 1935, pp. F-38-40. ? ( 4) BANCROFT, M. F., Geological Survey of Canada, Memoir 204, 1937, Gold-Bearing Deposits on the West Coast of Vancouver Island Between Esperanza Inlet and Alberni Canal. (5) STEVENSON, John S., British Columbia Department of Mines, 1938, Lode-Gold Deposits of the Zeballos Area. (6) MAcDoNNELL, G. F., The Privateer Mine, Zeballos; The Miner, Van-couver, B.C., December, 1938.

Jan 1, 1939