Search Documents

Zircon is extensively used as moulding sand in the production of steel and high-duty iron castings. To achieve a satisfactory grade of zircon concentrate, the zircon particles may need ,to have surface coatings removed, as such coatings can hinder electrostatic and magnetic separation of zircon from associated minerals. Xn addition the presence of surface coatings on the zircon. particles can cause sinterins and fusion of the zircon to the east metal resulting in "burnt-on" sand or fritting of the casting. "Burnon" necessitates cleaning of the casting by grinding or chipping, which is expensive and results in loss of definition on the casting face.Hudson (1966) has pointed out ,that some coatings on mineral sands are lightly-adhering clays which can be removed quite readily by agitating the sands in water for a few minutes-thus their removal constitutesno problem. However, the heavy gingery coloured coating which adheres strongly to the surface of the particles in some deposits, and which has generally been considered to be a form of iron oxide (Baker, 1962; Hudson, 1966), cannot be removed effectively by attrition cleaning in water (Hudson, 1966). Such coatings limit the usefulness of these concentrates in the foundry industry.An investigation of strongly-adhering coatings on "ginger zircon" concentrates from the Yoganup deposit of Westralian Sands Ltd has shown that the stain consists of a cemented mixtvre of hydrated iron and aluminium oxides and kaolin minerals, and that it can be removed by a relatively low cost treatment.IDENTIFICATION OF THE STAIN BY XRDX-ray powder diffraction (XRD) patterns were obtained from small samples of stain scraped, individually, from the surface of hand-picked zircon and ilmenite crystals. These scrapings were mounted on quartz fibres and exposed to CoKa radiation in a 57 mm Debye camera. To avoid heavy fogging of the x-ray films, a substantial amount of the iron oxides was preferentially leached from the scrapings (before mounting) with an ammonium oxalate-oxalic acid solution (Rooksby, 1961). The residual material gave a fairly well resolved powder pattern (Table 1). A...

Jan 1, 1975

By N Madani, N Battalgazy

Geostatistical simulation has been widely used in mineral resource classification of metalliferous deposits based on international standards such as JORC code which is one of the most extensively used around the world for reporting the mineral resources and ore reserves alongside with objectives of the companies (Sadeghi, Madani and Carranza, 2015). However, the modeling process becomes challenging whenever the relationship between the variables of interest is complicated and cumbersome to model. This characteristic sometimes manifests itself in complex spatial and global cross-correlation measures, deeply depending on the formation and genesis of the deposit. The objective then is to generate the models that not only reproduces these significant characteristics, but also, it leads to a better understanding of a mineral resource estimation and successive decision-makings. In this respect, there are different approaches taking into account the spatial correlation structures, for which can be classified as independent simulation, co-simulation, and factor-based methodologies. In this paper, three techniques: Turning Bands Independent Simulation (TBSIM), Turning Bands Co-Simulation (TBCOSIM) and Projection Pursuit Multivariate Transform (PPMT); from those aforementioned approaches are selected to model two cross-correlated variables (Iron and Aluminum Oxide) belonging to an Iron ore deposit located in Brazil, in order to examine which methodology better reproduces the corresponding complexity in terms of local correlation measure. CITATION: Battalgazy, N and Madani, N, 2018. Mineral resource assessment in complex ore deposits based on international standards, in Proceedings Complex Orebodies Conference 2018, pp 79–81 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

"DEEPHOLE " or "Longhole" drilling is the name given to the drilling of prospecting holes with the pneumatic hammer drill. The drilling bit is of the same form, and is prepared in the same way as ordinary rock drill steel, and is extended to the bottom of the hole by sectional hollow rods, through which water is forced.The cuttings from the hole provide a sample of the ground drilled.Deephole drilling was developed at an American mine where the cost of diamond drilling, owing to loss of diamonds, was excessive, and proved very successful, holes being drilled as deep as 220 ft., in limestone, at a cost of one dollar per foot. The use of the method in other mines, and in a variety of rocks, has since been described in the technical literature. From the published descriptions the following data are drawn:

Jan 1, 1930

By G Mudd, N Haque, S A. Northey

Life cycle assessment (LCA) provides an internationally standardised framework for estimating the environmental impacts associated with products or services (International Organisation for Standardisation, 2006). A particular strength of LCA is the ability to consider indirect impacts that occur at different stages of a product’s life (eg raw material acquisition, manufacture, use, disposal or recycling) and through its supply chain (Figure 1). A wide variety of impact categories are able to be considered by LCA, such as the potential contribution to global warming, ozone depletion, marine eco-toxicity or freshwater eutrophication.CSIRO has a long history of using LCA to compare the environmental impacts associated with alternative mining, mineral processing and metal production technologies (Haque and Norgate, 2014; Norgate and Haque, 2012, 2013). These ‘mine-to-metal’ assessments have primarily focused upon estimating embodied energy and greenhouse gas impacts associated with these production processes; however, more recently there has been a refocus to also consider consumptive water-use impacts in more detail (Northey et al, 2014).CITATION:Northey, S A, Haque, N and Mudd, G, 2016. Water-related data requirements for improved life cycle assessment of mining, mineral processing and tailings management, in Proceedings Life-of-Mine 2016 Conference, pp 16–18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

Powered support plays a major role in longwall mining and improper selection may lead to a disaster. While different countries follow different norms, a universal approach is needed to be developed. For this purpose, a computer program C-ALPS

Jan 1, 1998

The seemingly insatiable world demand for mineral and energy products is continuously pushing out the frontiers of exploration and development in countries around the Pacific Rim.

Jan 1, 1990

By Atkinson D

This paper briefly outlines the develop ment of the froth flotation plant at Coal Cliff Colliery. The plant was superimposed onto the original flow sheet in which fines were merely thickened and filtered. Test work leading up to the installation is described and the final layout is discussed. Details of the concentrate and tailings systems are given. Preliminary results of a further extension involving the use of a Davcra flotation machine are also given.

Jan 1, 1974

The chief use of manganese ore is in the production of ferromanganese alloys for steelmaking. Manganese ores generally occur in tropical areas, which influences the type of treatment required. Present methods of treatment are relatively unsophist- icated but demands by customers for tighter specifications will necessitate the installation of gravity concentrator at many mines At present only limited tonnages of minus j in. product can be sold hence future development will centre around methods of producing an agglomerate satisfactory to the smelter.

Jan 1, 1969

Hydrocyclones are widely used in both mining and various industrial sectors. Considerable fundamental research work on the modelling of hydrocyclone classifiers has been carried out through the past 25 years. Based on the similarity principle, the hydrocyclone classification was taken as a whole physical process and a group of similarity numbers were obtained with the help of dimensional analysis in this paper. Then, the functional dependences of the similarity numbers have been established. The variables optimisation was carried out with the multiple objectives linear planning programs developed in this study.

Jan 1, 1993

The output of Dexin Pit Copper is up to 33 million tonnes a year and the final depth is more than 500 m. As a cost reduction measure, the in-pit crushing and conveying system has was introduced to deliver ore from the pit to mills. This paper describes the in-pit crushing and conveying system, and highlights the optimum level where the shovel-truck haulage system transfers into In-pit Crushing and Conveying system, relocation of an in-pit crushing system, and includes the impact of the transferring point when the costs change.

Jan 1, 2003

By Equivar J, Mirabal C, Pyper R

In 1984, work was started to determine the viability of heap leaching silver-containing waste dumps from Cerro Rico near Potosi - Bolivia, at an elevation of 4300 meters (14 100 ft.). The result today is an unusual heap leach utilizing fine crushing, grinding, and agglomeration to process 1000 tonnes per day of ore containing 200 g/tonne silver. The unique metallurgi- cal, economic, and political factors will be discussed which led to the decision to build a heap leach rather than a conventional agitation leach plant. Capital and operating costs will be given along with some of the uncommon process design and equipment problems encountered while developing the operation.

Jan 1, 1991

Largely inherited from the past and from strictly internal laboratory use, the certification of reference material using round-robin assaying is often insufficient for the use made today for external assay laboratory control by client parties. Certification often needs to be revisited on the basis of existing round-robin data, especially to derive reproducibility parameters to the end of establishing probabilistic performance gates for operational error detection on a batch per batch basis (ie batch-ærejectionÆ). The most common difficulty arises when only a few certification samples have been analysed in one single batch by each laboratory, so that the round-robin data do not contain the full variability that needs to be quantified. Existing certification data sets from properly submitted round-robin samples were studied using analysis of variance to derive a remedial method, leading to the proposal of default correction factors to restore full variability estimates when no other avenue is available.

Jan 1, 2008

The Broken Hill orebodies have 'traditionally been mined by cut and fill trethods. In the mid-1950's New Broken Hill Consolidated Limited experimented with sublevel longhole open stoping but did not pursue the method due to inefficient loading and poor fragmentation. The introduction of longhole open stoping in 1968 was a radical change and was necessary to enable the profitable extraction of lower grade orebodies and this method is now used for 55% of the production from The Zinc Corporation, Limited and New Broken Hill Consolidated Limited mines.

Jan 1, 1982

This paper addresses the unique environ- mental programmes which prevail at Ranger and their importance in the future profitability, of Ranger Uranium Mines Pty Ltd. (RUM) Industrial relations, general safety, and occupational health have long been regarded as part and parcel of the concept to 'manage for profits'. More recently, the need for environmental protection has also become an important management consideration. This is particularly so at the Ranger Uranium Mine where environmental protection is very closely and continuously regulated. Since the commencement of operations at Ranger some three years ago the company has operated within these regulations and demonstrated clearly that yellowcake can be produced efficiently, economically and safely. The company also recognises that in order to ensure continuity of production, it will have to continue to operate within these strictly supervised Regulations.

Jan 1, 1984

One of the major changes in the resource industry in the nineties has been the re-internationalisation of the industry. The history of the resource business has been one of companies from the developed world utilising the cash flows from their operations to explore and develop mines in less developed regions of the world. This resource development has progressively generated wealth and economic development, which in turn, has led to a new generation of exploration and mining projects. In South America, Chile had led the way in a mining resurgence, now closely followed by Argentina, Brazil, Venezuela and Peru. Although Chile has long had a significant copper mining industry, the pre-nationalisation phase was driven by American capital; the current phase has been spearheaded by R.T.Z. - B.H.P. at Escondida with Canadian junior companies, in particular, providing major speculative impetus. The Australian junior companies have not been significant in South America.

Jan 1, 1995

As Coal Mining Areas develop, problems relating to strata control increase. The "easy" coal has been extracted and the future development lies in the direction of greater depths of cover and more difficult strata conditions. To provide solutions to the problems encountered the techniques of constructing and testing physical models have been developed and refined. With a sound knowledge of model theory allied to practical experience, mining research engineers use physical cemented material models to examine, assess and solve mining problems relateu to strata behaviour and environment. For a model to provide the answer to a particular mining problem it is essential that as much information as possible be obtained from the mine or area of a mine which the model is to represent. Details relating to the strata, geological malformations, and the stress environment must be collected and collated to ensure reliable results.

Jan 1, 1976

By J M. Dwyer, S Williamson

Acceptable post-closure performance of decommissioned mining operations is a critical factor in persuading todayÆs environmentally conscious public that the mining industry will not continue to burden future generations with the legacy of environmental tragedies. Post-closure impacts must be identified and managed through robust engineering design if the post-closure environment is to be environmentally sustainable. To manage potential post-closure risks (environmental, health, safety, social and economic) within acceptable limits, WMC incorporates a risk-based approach to closure planning and engineering design. WMCÆs risk-based closure engineering design process provides a simple methodology for developing robust closure plans û the process æengineers outÆ unacceptable risks and æengineers inÆ a sustainable post-closure environment. Benefits of the risk-based process include stakeholder endorsed closure criteria for an agreed post-closure land-use, focusing of resources on major risks, and a realistic and accurate estimate of the required closure provision. The outcome is an increased likelihood of satisfying the three pillar goals of sustainable development û a financially sound solution that poses a low risk to the environment and future generations.

Jan 1, 2003

By N Ross, N Goldup

In recent years the heavy mineral mining industry has started to look more closely at the feasibility of mining moderate to high slimes deposits. During the initial stages of orebody evaluation the primary purpose of the pilot plant is to produce heavy mineral concentrate for metallurgical evaluation. Hence, generally little consideration is given to the disposal of the waste material (slimes and tailings). This paper suggests additional, simple, low-cost, tests that can easily be incorporated into an initial pilot plant operation. With this data a more definitive evaluation of available waste disposal options can be made during the early stages of the project. Thus, permitting better project focus and utilisation of resources. These tests include free settling of slimes, natural slimes drying and consolidation (undrained and drained), tailings stacking angles, and particle size distributions of input and waste streams, etc. The objective and method of each test is summarised, together with its relevance to possible waste disposal options. The results of this preliminary testwork can later be used to expand upon and define further tests for the second phase of pilot plant operations, which will enable a more definitive evaluation of a proposed waste disposal solution.

Jan 1, 2001

Passive systems for the treatment of acid mine drainage (AMD) are typically more economic in the long term than active systems. Various flow charts for treatment selection have been prepared by scientists in the USA, however, they have typically not included a variable important at New Zealand AMD sites on the West Coast: topography and available land area. Very steep topography, dense and often protected vegetation (and animals such as snails), and a high-rainfall climate result in AMD with very high flow rates in locations with very limited space for remediation. Flow charts specific to New Zealand have been prepared which accommodate topography and available land area. Parameters necessary to use the flow charts are iron and aluminium concentrations, pH, ferrous to ferric iron ratio, dissolved oxygen concentration, topography and available land area. Prior to full scale construction, is it recommended that flow rates be quantified, small-scale trials be conducted, and cost, effectiveness, limitations, and risk of failure be reviewed for various options. One full-scale remediation system has been installed in New Zealand based on this methodology and another is planned. The performance of these systems, as well as future systems to be installed, will be used to validate these treatment system flow charts.

Jan 1, 2007

By Lysnar R, Horswill M

Since the introduction of the pocket calculator, electronic measuring equipment, lasers and computers, the mine surveyor's approach to his work has changed. Where he once used steel bands he now uses infra-red, visible light or radio waves. The reading and storing of angles is done automatically and he now has to be familiar with the facilities that a computer can offer, instead of plotting and calculating manually. This highly sophisticated equipment is continually being upgraded, modified and fine tuned. This paper will attempt to highlight some of the equipment at present in use by the surveying profession and research currently being conducted by the WA School of Mines. The various options in EDM will be considered including the latest unit capable of measuring distance without the benefit of a reflector, thus enabling the surveyor to co-ordinate points that were previously thought inaccessible. The School is currently working on changes to the GAK1 Gyro Theodolite which may improve results and enable the operator to have more control and confidence in his observations. Areas under consideration are improved lighting, binocular viewing and interfacing the instrument to a stopwatch. In the last few years the computer is being used not only for surface pickups and control but also for underground work. We will highlight the underground options in this area and the software available.

Jan 1, 1987