Search Documents

By M Noy, P Hawkes

Improvements in the drill and blast process can impact on loader performance in a number of ways. The main effects being improved loading cycle times, less non-productive cycles such as oversize removal, clean-up and face raking and better bucket fill factors. The impact of improved loading cycle times on the overall cost and productivity of the load and haul cycle is very much dependent on the loader truck match and the management of the haul fleet. Previous work has shown that a 20 per cent improvement in dig cycle times may only lead to three per cent or less improvement in the overall productivity of the load and haul process. However, improving the mass loaded per pass by five per cent will lead to a five per cent improvement in productivity for any given haul fleet situation, assuming sufficient truck capacity. Work by Orica Explosives at Lab ChrysotileÆs Thetford Mine, Quebec, Canada showed a relationship between muckpile fragmentation and truck payload. With this in mind, work was carried out to determine the effect differing muckpile fragmentation distributions can have on excavator bucket fill factors. This work was performed in the laboratory to a 1:100 scale. Nine different distributions were used. These were characterised by the Rosin Rammler parameters, xc the characteristic size, and n, the uniformity index. The values of xc and n used were modelled on those previously measured at a Sydney quarry. For the range of distributions measured, it was found that the fill factors were lowest at a low characteristic size and a high uniformity index and highest at a high characteristic size and a low uniformity index. In other words the best fill factors were achieved with a more dispersed muckpile distribution with a larger characteristic size. The difference in fill factors was 16 per cent indicating that controlling the drill and blast process to produce a specific muckpile distribution can have a significant impact on the overall cost-efficiency and productivity of the load and haul process. Field measurement by Orica Explosives at a quarry in Canada supports this conclusion showing improvements of up to seven per cent in average bucket load by either increasing the characteristic size or decreasing the uniformity index of the muckpile.

Jan 1, 1999

By Hutton W

The Argyle Diamond Mine is the first significant diamond producer in Australia. The project has been developed with new concepts in circuit design, process control technology, organisational development and training. After its first year of operation, the Argyle Heavy Medium Separation Plant has proven extremely efficient in recovering diamonds. Apart from cyclone wear, no major problems have been encountered. Ferrosilicon consumption is well below the design level which is a reflection of the sound design of the medium circuit. An Audit Plant continuously monitors the Heavy Medium Separation Plant tailings for diamond loss.

Jan 1, 1987

Agitation leaching data has generally not been analysed to extract the maximum amount of information that is available. Analysis of heap leaching systems has been developing over the last five years to include the underlying rate determining process. This has been found to be diffusion control for all copper leaching; irrespective of whether they are oxide or sulfide minerals. Extension of the diffusion model has enabled better scale-up protocols to be developed. Acid consumption in copper heap leaching operations has been found to be a first-order chemical controlled system. The analysis of the data is relatively straightforward. However the interpretation and scale-up is not as direct as for agitation leaching. The differences in the residence time distributions (RTDs) are required to properly account for the scale-up between test columns and field. The leaching of oxide copper in agitated systems has also been found to be diffusion controlled. However, there are significant differences in the control mechanisms. Initially the leaching control is the supply of acid to the mineral surface. This is limited by the diffusion through the surface boundary layer and is thus subject to the level of agitation. Higher agitation provides thinner boundary layers and faster diffusion rates. Similarly, higher grade material creates a thicker concentration boundary layer and relatively slower leaching. Acid consumption in agitated leach systems is also a first-order system. However, the interpretation of the RTD is easier from batch testing to continuous multiple CSTR series plant operations. Altering the method of acid delivery can significantly reduce acid consumption rates. Predilution of the acid minimises the local acid concentration near the addition point and can reduce the consumption by up to 50 per cent. Modelling of the combined leach rate(s) and acid consumption rates in agitated systems allows comparison of various leaching strategies and selection of the most appropriate. Similarly, the model allows the identification of economic limits to leach recovery; where the cost of acid consumption is greater than the value of the copper recovered. From this analysis selection of residence times for agitation leaching can be determined. The modelling tools are useful in identifying optimum conditions for the leaching process.

Jan 1, 2005

A number of suggestions have been made to improve the design of cells used for electro winning and electro refining of metals. Most of these designs have been aimed at increasing the current density used in order to improve cell capacity, although the purpose of some has been to produce electro deposited metals in a continuous manner. Improvements in the electrolyte flow pattern in conventional cells have resulted in an increase in the rate of mass transport of metal ions to the electrode surface; giving rise to lower concentrat- ion polarization and an improvement in the nature of the product obtained, Other cell designs are based on a moving electrode, usually a rotating disk, and these may include provision for removal of the product in a continuous manner, The maximum current density which can be used in an electro- lytic deposition process is determined by the limiting diffusion current, the physical nature of the, product, the purity of the product required and by the increase in power costs which result from the higher cell voltages, This paper examines the properties of an agitated bed of particles as an electrode system when used for a metal deposition Process,

Jan 1, 1969

By T Akiyama, J A. de Castro, H Nogami

Blast furnace is a countercurrent moving bed reactor that produces pig iron from iron bearing materials like pellet, sinter or lump ore. The furnace has cylindrical shape and the lump solid materials are alternatively charged onto the top of the furnace. Hot air is introduced through tuyeres that are set on the lower furnace wall. Auxiliary fuels (pulverised coal, oil or natural gas) and raw materials (fine ore or fluxes) are injected into the furnace with blast air from the tuyeres. In front of the tuyeres, coke particles react with oxygen in the blast air and generate carbon monoxide. The hot reacting gas heats up the lump solids and reduces iron oxides in the upper furnace. In the middle height of the furnace, the reduced iron and slag are fused by the combustion heat and form the cohesive zone. The molten iron and slag that are generated in this region trickle down through the packed bed of coke particles and flow into the bottom of the furnace. Therefore, the flows of gas, lump solids and liquids exist at the same time in the lower part of the blast furnace.

Jan 1, 2000

By Deutsch G. P

The output of an underground mine often depends entirely on the mine winding system. -Decisions made--at the design stage affect the economy and operation'of the mine'.througb -its entire life. A modern mine winding installation is an integrated system and its design requires a multidisciplinary approach including expertise in the-materials handling, mining, mechanical, civil, structural, electrical and control engineering fields. The paper-sets out the elements of typical mine wind- ing systems-and describes some of the more important decisions which must be made during the planning and design process, It is no longer.adequate to. base the choice of a system on the pre- ferences and experiences of individuals. Major Australian winding install- ations are usually designed on the basis of overseas experience and some of the detail design is often carried, out overseas. Differences in basic design criteria occur from country to

Jan 1, 1973

Although the 'exi'stence of bauxite in Australia has been known for many years it is only recently that exploitation has commenced.. of the two most' important` deposits, strangely at almost diagonally opposite tips of the continent. Recognition of the importance. of the bauxite in the South/West corner came about initially through the efforts of a well-known Australian mining company which,` with some outside financial help, tackled the early exploration with commendable foresight and courage.

Jan 1, 1964

The use of pipeline-c to carry crude'oil and petroleum pro-ducts is a reliable and economic*Way to transport large quantities of oil. The length and size of these pipelines have continued to grow throughout the world as the demand for petroleum has in-creased and as the price of other transportation-methods has risen. At the present time pipelines 'can move a barrel of oil a distance of 100 miles at an average cost of ,80.06 U.S. dollars.The major elements in pipeline design are discussed. Methods of calculating pressure drop and horsepower requirements are pre-sented. These are variations of standard equations.in which the elements of each equation are expressed in terms common to the petroleum industry. Major equipment is discussed., particularlyas it relates to operation and economics.Cost data are presented to aid in preliminary economic ana-lysis. Curves illustrate the cost of oil transportation at flow rates between 10,000 and 500,000 barrels per day and permit the selection of pipe diameter-which will result in minimum operating costs.

Jan 1, 1962

Many stress measuring instruments use overcoring stress-relief principles but adopt different sensing techniques. Every technique is subject to certain limitations of rock types and conditions. To investigate the performance and reliability of the instruments in field measurement, a simple and practical approach has been developed to allow comparable laboratory results to be obtained which simulate in-situ rock and stress conditions. Four commonly used devices, the USBM deformation gauge, the CSIRO HI cell,the CSIR triaxial cell and the UNSW SI cell were thoroughly tested in the laboratory. Some conclusions have been drawn as to their suitability and reliability in different field conditions. Recommendations are provided for the choice of an appropriate technique for a given rock type and condition. A new thin-wall cell that overcomes the disadvantages of earlier devices has been developed and tested. Its laboratory performance shows that it has good prospects.

Jan 1, 1990

This paper reviews the developments in understanding of the entrainment mechanism and its modelling in industrial flotation processes over the last 30 years. Both valuable and gangue minerals in the pulp zone of an industrial flotation machine can be transported through the froth zone to the concentrate launder in the water which must also be transferred from the pulp zone to maintain a stable froth zone in conventional flotation. A size dependent portion of each entrained mineral continues in normal circumstances to the concentrate launder. The size dependency arises because the larger particles are able to drain more successfully from the froth region. Gangue minerals are recovered by a number of mechanisms, entrainment being an important one in many cases. The entrainment mechanism is discussed on the basis of the pattern observed in recovery û size data for minerals. Its industrial implications are discussed and means of minimisation of the importance of the mechanism are also discussed. Various means proposed for mathematical modelling of the entrainment mechanism are also described. The effect of process variables on key parameters in these models is reviewed. Properties of both the pulp and froth zones are discussed where needed and means of taking additional measurements with devices developed over the last ten years are discussed as part of the collection of more detailed data on the flotation process in general and the entrainment mechanism in particular.

Jan 1, 2005

The Australian mining industry is at an interesting stage in its development. Of the large number of mining companies in Australia, some are still solely domestic in their focus. others have made their first tentative forays offshore, and others are global players of significance in the world industry. It is not long ago that the entire industry was almost exclusively domestic in its focus. Very few companies before the early 1980s had ventured offshore, and those that did so were considered quite risque. The initial moves were made mainly by large companies who could afford to lose the funds expended in getting started in a range of offshore locations.

Jan 1, 1995

Development of a New Dry Density Separator for Fine-Grained Materials

Sep 13, 2010

Simple quotation of quantities of coal reserves neglects the relationship between qualities of coals and their efficient use. If exploitation of a deposit is contemplated, its life expectancy can be deduced only if its reserves are estimated according to the coal user's technological standards. A wide range in properties will satisfy a steaming coal, whereas a high vitrinite high rank coal would be preferred for coking and a low inertinite low rank coal for conversion. In competitive trading the buyer's commercial specification may require weighing against the producer's practical ideals, especially when beneficiation is critical. Differentiation of grades in quality of a deposit provides an intelligent understanding of the economic importance of the deposit. The Wongawilli seam of the New South Wales Southern Coalfield exemplifies the effect of quality criteria upon the extent of in situ, recoverable and marketable classes of economic reserves. Effective management of a deposit will result from simultaneous quotation of coal qualities and quantities in a statement of its reserves.

Jan 1, 1979

This paper describes the application of the Total Productive Management (TPM) technique as a performance improvement initiative for a coal mining operation. It discusses the objectives of TPM, with the driver for improved production performance being the Overall Equipment Effectiveness (OEE) of the equipment or process, and with the development of "ownership" as the behavioral approach to equipment management and continuous improvement through cross-functional and area-based teams. It illustrates the concept of equipment management as defects management.The scope for application of TPM to the coal mining industry is immense. The harshness of the operating environment can be a major generator of equipment defects, and a current paradigm in the industry accepts these defects as an unavoidable outcome defining maintenance costs in this environment. However recent benchmarking studies have highlighted that maintenance costs per operating hour in some mining operations are more than double the vendor's estimate of "best practice". The paper refers to these studies which also compare maintenance costs of fixed and mobile plant and equipment to "best practice" outcomes in comparable process industries.

Jan 1, 1998

By K Paki, K Parker, J F. Dupont

The Mount Charlotte grinding circuit at KCGMÆs Fimiston mill was recently equipped with three 650 mm CAVEX cyclones in order to improve the overflow P80, reduce the fines bypass to the underflow and improve the underflow density/recovery of water to the overflow. After the first two sets of surveys were conducted air core boosters (ACBs) were installed on the 650 mm CAVEX cyclones in an attempt to further increase their performance. JKTech was approached to assist with the examination of the data obtained from the surveys; this data was intensively modelled to determine, to a high degree of confidence, the impact the changes to the cyclones had on the classification and the benefits to the plant. This paper outlines the outcomes of the trial and the methods used to determine those outcomes.

Jan 1, 2007

By A Domanti, C Jewkes

This paper describes the design and constructability issues investigated in the selection of a trenchless solution in comparison to trenched construction options as part of a scoping study for the augmentation of the existing Bulimba Creek Trunk Sewer in Brisbane. Initial work involved the planning of alignment options vis-a-vis ground geology, geotechnical conditions, location and depth of shafts considering potential construction technology, flotation and stability of the tunnel, availability of construction sites and the influence of construction works on neighbourhood properties and the immediate environment. Two design pipe sizes, DN1200 and DN1500, were considered, and factors including jacking forces, specification of product pipes, pipe joints, pipe jacking methods and the associated impacts of ground settlement were carried out. Of particular interest was research on suitable lubricating fluids with the potential to minimise jacking forces and maximise the length of pipeline between launch and reception shafts.

Jan 1, 2008

The Japanese Government promulgated the æLaw Concerning Special Measures Against DioxinsÆ on 16 July 1999 and it was enforced on 15 January 2000. This is a unique law specialised to protect the environment by the control of dioxin emissions from waste incinerators and several industrial processes. In this law, a few metallurgical processes other than waste incinerators are designated as æspecified facilitiesÆ emitting certain dioxins. Thus, emission standards for dioxins to the air were set for electric arc furnaces (EAF) for steelmaking, iron ore sintering, zinc recovery from EAF dust and aluminum recycle processes. In this paper, the inventory of dioxin emissions for Japan and the recent research and development to reduce emissions from those processes are introduced. Further, some details on the formation mechanism of dioxins and future subjects for effective control of their emissions are discussed.

Jan 1, 2002

By M J. Ireland, D P. Horne, S J. Simpson

The Sinclair Nickel Project, wholly owned by Xstrata Nickel Australasia (XNA), includes an underground mine, a concentrator, a village, an all-weather airstrip and associated mine infrastructure. The operation is located 70 km north of Leonora in the prospective and historically productive eastern Goldfields region of Western Australia. Xstrata Nickel has successfully developed the Sinclair deposit into a 350 kt/a operation since its discovery in November 2005, with contained nickel metal production to date in excess of 10 600 t, of which 5500 t is from the underground operation.The narrow, continuous, medium-grade Sinclair nickel sulfide deposit accessed by the Phoenix Decline has a shallow 15¦ - 20¦ plunge that is approximately 1000 m long down dip and open at depth to the north. The flat plunge and low-grade nature of the orebody presents challenges regarding the amount of horizontal waste development that can be economically excavated, which in turn affects ventilation, egress, mine services and diamond drilling.The mineralisation is hosted between an ultra mafic hanging wall and a basalt footwall and is being mined using a bottom up, sublevel open stoping method. The stopes are retreated to a central access, filling voids in the process with waste mullock where possible and using cemented mullock fill where end exposure is required. Tight filling the flat dipping hanging wall has proved to be challenging given the angle of repose for the waste mullock fill is steeper than the angle of the hanging wall.Reconciliations of mine performance against the original feasibility study show positive changes and operational optimisations enabling Sinclair to achieve its mining targets in a safe, sustainable and economic manner. This paper discusses the mining operations associated with the first two years of the Sinclair Underground Nickel Project, providing an overview of the various issues encountered and the lessons learnt in the process.CITATION:Ireland, M J, Horne, D P and Simpson, S J, 2012. Overcoming mine design and production challenges at the Sinclair underground nickel project, in Proceedings Narrow Vein Mining 2012 , pp 37-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

With the exeption of the United States, Canada and Russia, oil has not been around in quantity near world centres of population. Production: in Western Europe is insignificant. Japan is without production as are Australia, Southern Africa, India; Brazil, Chile, New Zealand and China. The United States is, however, a large importer of crude oil. The very fact that oil is produced generally away from centres of population means that it has to be carried by sea to the area in which it is required. There is, therefore, a constant flow of oil around the world in very definite channels.

Jan 1, 1962

This paper addresses; land use, rehabilitation and the State/Federal regulatory process, in light of Australia signing various international conventions and agreements in the area of environmental protection. The conventions on biological diversity, climate change and the implications of the Rio and Agenda 21 declarations are examined. The implementation of these initiatives through the Inter-Governmental Agreement on the Environment, and through legistlative mechanisms at Federal and State level is explored.Particular attention is given to the biodiversity strategy in context of the need to integrate economic aspirations and environmental concerns as a basis for sustsainable development. The paper concludes with a brief comparison of the major approval processes in each State, relating to mining environmental issues.

Jan 1, 1992