Search Documents

By W Boughton, L Gilbert

The Australian Water Balance Model (AWBM) has found widespread use in Australia in estimating the streamflow behaviour of catchments. It has been used at the Ridgeway Gold Mine, in central west New South Wales, to estimate streamflows in creeks potentially affected by loss of spring-fed baseflow due to mine dewatering. The AWBM estimates are used to assess the effect of mining on streamflows and the need to provide compensatory flow releases, which would be drawn from mine water supplies, into the creeks, in compliance with regulatory consent requirements. The monitored flows in some of the creeks exhibit non-typical behaviour, with streamflows increasing in autumn months despite a lack of significant rainfall. This behaviour is believed to be due to the combined effects of discharge from rock fractures and the effects of evapotranspiration in the riparian zone. A modified version of the AWBM has been developed which much more closely simulates the observed flow behaviour and which will be used in ongoing flow assessments for the mine. This paper outlines the difficulties involved in modelling low flows in small catchments that are subject to a number of influences (other than mining), describes the development of a refined model to improve simulation of low flows and baseflow in small headwater catchments and highlights the need for good baseline data to calibrate such models.

Jan 1, 2006

By G Harbort, T Georgiev, M Phillips

Phu Bia Mining Ltd, a subsidiary of Pan Australian Resources Ltd owns and operates the Phu Kham copper concentrator located in the Xaysomboun District, Lao PeopleÆs Democratic Republic. Construction and commissioning of the 12 Mt/a copper concentrator and associated facilities was undertaken by Ausenco Ltd and handed over to Phu Bia Mining Ltd in April, 2008. The first copper concentrate was produced in April 2008 and the ship carrying the first shipment of copper concentrate set sail 27 July 2008. Nameplate mill throughput was reached in August, 2008 when 1 020 000 dmt of ore was treated in the milling and flotation circuit. The Cu-Au mineralisation is contained in skarn and stockwork mineralisation and is interpreted as a distal expression of a conventional porphyry copper-gold system. Copper mineralisation is principally in the form of chalcopyrite with lesser bornite. Gold occurs as small grains, typically associated with copper minerals. In the upper portions of the orebody, oxidation and water table movements have resulted in near surface leaching of the copper and below the leached zone, supergene enrichment resulted in chalcocite mineralisation. The circuit operates with a semi-autogenous grinding (SAG) û ball mill circuit, feeding a bank of OK200 rougher cells. Rougher concentrate is reground in an IsaMill prior to entering a cleaner circuit consisting of three stages of cleaning and one stage of cleaner scavenging. The concentrate typically assaying 24 per cent Cu and 6 - 7 g/t Au is hauled for over 1000 km across the border to the Port of Sriracha in Thailand, and stocked in sheds at the wharf from which it is shipped to various Asian smelters. This paper discusses the successful commissioning and ramp up to design tonnage and metallurgical performance. In addition, a program to optimise both the comminution and flotation circuit is detailed with reference to grinding efficiency, flotation residence time and size by size mineral recovery.

Jan 1, 2009

By Fisher WJ

The'treatment of the South Alligator valley uranium ores passed through three phases dictated by economic circumstances during the years 1956- 640 In the first phase high grade ores were treated by hand sorting and wet gravity separation for recovery of high grade concentrate to meet a United States Atomic Energy Commission (U.S.A.E.C.) contract for plus 50 per cent pitchblende concentrates. Secondly tailings from the gravity plant and some high grade ores were trucked to Rum Jungle and sold to the Australian Atomic Energy Comm- ission (A.A.E.C.). Thirdly solvent extraction plants were built at Moline (previously Northern Hercules) by United Uranium N.L. (UOU.N.L.) and at the South Alligator River by South Alligator Uranium N.L. (SOA.U.N.L.). These were the first solvent extraction plants designed in Australia, as earlier plants used the ion exchange process for recovery of uranium oxide. The plants were small, indeed the S.A.U.N.L. 15 ton per day plant was possibly the smallest commercial plant known, but they operated efficiently with good recoveries, and were placed on a care and maintenance'òbasis when contracts were filled. Sulphuric acid was supplied in bulk to both plants by the A.A.E.C. from the 30 ton a day acid plant at Rum Jungle. Gold was recovered as a by product of uranium ore from the Moline plant.

Jan 1, 1968

Host minerals for gold have been of great interest to exploration geologists and metallurgists for a variety of reasons. The depletion of high grade ores in many parts of the world requires that greater attention be given to the study of host min-erals for gold. Some host minerals have been employed in exploration as traces for gold. They are also essential in the design of extraction processes for treating gold ores.This paper reviews the mineralogy of important gold deposits of Papua New Guinea (PNG), Indonesia and New Zealand and focuses attention on the ore minerals and rock-forming minerals that host gold.

Jan 1, 1994

By McPherson M. J

This paper describes a major ventilation study for the expansion of the El Teniente mine operated by Codelco, Chile. El Teniente is one of the world's largest under- ground mines. The design effort was under- taken in three stages and involved a partial mine ventilation survey with network simula- tion, detailed stope ventilation investiga- tions, and design of the entire mine ventila- tion circuit based on production plans to achieve 112,000 tons per day by 1995. The partial ventilation survey provided values of representative friction factors and resistances for typical ventilation raises and airways. These values were used to conduct detailed modeling of the block caving levels to investigate the most cost effective and practical means of providing the required ventilation. The results of these analyses were extrapolated to the proposed expanded mechanized zones.

Jan 1, 1988

The occurrence of metallic minerals in Australia to the time of the proclamation of South Australia as a Colony in 1836 was unknown. It is, therefore, perhaps, surprising that British settlers arriving in the Coromandel included among their number a German scientist Johannes Menge who had been appointed by the South Australian Company to the post of Mine and Quarry Agent and Geologist on 1 July 1836. His instructions were to `explore the natural productions of the Colony above and below ground and to superintend the working of quarries of stone and slate, the boring for water, metal, lead, coal and other mines at a salary of ú150 per annum for one year and for as much longer as the Company require your services not however exceeding five years'. In the event, he was to have little influence on those matter.

Jan 1, 1993

The state-owned Swedish company LKAB is one of the world's largest producers of iron ore. LKAB mines the greater part of its ore underground, and very high efficiency is vital if it is to compete successfully with open pit mines. Consequently, computers and OR are essential parts of the company's operations. This paper gives some examples of success- ful computer and OR applications at LKAB, coupled with some remarks on the costs and benefits of OR.

Jan 1, 1977

By Yao S, Wang P, Zhang C

The Zhilingtou Au-Ag deposit is situated in the eastern part of the complexly deformed and metamorphosed South China Caledonian Fold Belt. It consists of seven orebodies that are almost exclusively hosted by biotite plagioclase gneiss of the Precambrian Chencai Group. They form an apparent en echelon pattern in both cross-section and level plan. Three different ore types, based on mineralization textures, have been recognized within the Zhilingtou lode. These are Au-Ag-rich quartz veins, Au and Ag-bearing silicified rocks and Au-Ag-containing altered rocks with quartz stockworks. The mineralization is principally composed of electrum, argentite, pyrite and minor sphalerite, galena as well as traces of hessite and chalcopyrite plus a gangue assemblage of quartz, rhodonite, sericite and chlorite. Fluid inclusions related to Au-Ag mineralization yield a wide range of homogenization temperatures from 110 to 447¦C, with two distinctive peak values at 250-300¦C and 350-400¦C respectively. S30Si values of quartz veins and silicification from the three stages of mineralization range from -0.1 to -0.4%o. The mineralization at Zhilingtou is interpreted as forming by recirculated meteoric water extracting ore-forming elements from metamorphic rocks due to Mesozoic volcano-magmatic activity.

Jan 1, 1995

Spatial data processing using geographic information systems produces qualitative results which are superior to those from other existing software tools. However, the answers to various quantitative questions in mining operations is often limited by the capacity of the GIS to process appropriate spatial data. The efficient operation of a large underground mine demands that an adequate GIS be put in place.

Jan 1, 1995

By G Power

The successful implementation of sublevel caving (SLC) at Ridgeway Gold Mine (Ridgeway) requires the technical aspects of caving and flow behaviour to be understood. Cave propagation must be controlled and continuous to allow safe extraction of ore below. The understanding and use of processes to manage granular flow behaviour are also required to ensure economic metal resource recovery. Caving and flow technologies are thus critical to the economic viability of the application of the SLC mining technique to Ridgeway Gold Mine. At the time the Ridgeway SLC design was approved there were significant technical uncertainties associated with cave mining methods, including the SLC mining method in competent rock masses. This was in spite of the fact that caving is a relatively low cost mining method. Unique features generating technical risks at Ridgeway include: the fact that the orebody is blind (550 m below surface); highly competent cap rock (RMR >50); and high aspect ratio (height to width ratio of 3:1). Due to the presence of these unique features Ridgeway is considered to be beyond the current state-of-the-art in SLC mining technologies. The success of the technique at Ridgeway to date has indicated that blind SLC mines in strong rock mass can be operated safely and productively, if the technical risks are understood and properly managed. The risk management process was defined by the use of a formalise process to identify and assess the risks to the mine. The major mining related risks were formalised into Major Hazard Management Plans (MHMP) which contained a description of the risk, early triggers indicating the creation of a hazard and a series of agreed responses to be automatically initiated in the event of each trigger occurring. This paper outlines the following with respect to the critical technology areas of caving and flow: international industry, state-of-the-art technology; gaps in the application of this technology; the application of risk management, new processes developed at Ridgeway to bridge these gaps, including issues encountered; and trials and experimentation conducted to develop the new processes.

Jan 1, 2003

By Sivell W

We discuss the origin of the Patuki ophiolite complex and the Dun Mountain ultramafics of Middle Permian age in Nelson, New Zealand. It is shown that the Patuki volcanics have strong affinities with tholeiites of mid ocean spreading ridges transitional to alkaline basalts similar to those from fracture zones and ocean islands. At D'Urville Island, typically pillowed alkaline basalts enriched in rare light rare earth elements (LREE) - ophitic spilites - are associated with LREE-depleted (N-MORB-like) tholeiitic spilites with intergranular textures. The metabasalts are associated with a wide variety of sediments, and with sediments are intruded by conformable sheets of serpentinite. Coarsely crystalline mafic and plagiogranitic rocks signify vents and magma chambers, and we propose that the group developed as ocean crust from a slowly spreading mid-ocean ridge, transform association, overwhelmed at intervals by volcaniclastic sediment. Detailed mapping at a scale of 1:5000, and stratigraphic and geochemical development and structural coherence, show that the group is not melange in the Franciscan sense. The Dun Mountain Group, of serpentinites, peridotites, dunites, gabbros and other rocks, intruded the upper Patuki Group as a linear series of aligned pods and sheets. They carried up with them tectonic inclusions of older rock, which were metasomatised, and altered wall-rock, and one low angle dike passed several hundred metres into overl~ing sediment, at moderate temperatures (500 C). The rocks did not act as a floor (and alleged source) for the Patuki, but partly post-dated and were emplaced into Patuki.

Jan 1, 1987

Stressed steel cables, similar to those used in pre-stressed concrete, have been used for rock mass reinforcement, in civil engineering, for many years. This type of reinforcement has been attempted for open pit wall support, on several occasions, but has never gained wide acceptance as a practical approach because of high cost and complexity of installation in a mining environment. On the other hand, untensioned, fully grouted cable dowels (cable bolts) have gained wide acceptance for ground support in underground mining and it is perhaps surprising that this technique has not been used to a greater degree in open pit mining. The first systematic application of this technique in Australia was at the Mary Kathleen uranium mine in 1976, where it was spectacularly successful in maintaining steep stable walls in a jointed rock mass with unfavourably dipping structures. Cable bolting, and other techniques, are now being used to an increasing degree for wall support in both small and large open pits, for two basic applications: 1. stabilisation of potentially unstable sections of a wall, or 2. to allow steeper walls and reduce waste stripping volumes. In virtually every situation, wall rein- forcement has significant economic as well as technical advantages. The paper describes the development of the techniques, the mechanisms of wall support, the methods used, and discusses several case histories of its application to Australian open pit mines.

Jan 1, 1986

The Kundana underground narrow vein gold mine had a recent history of large and damaging seismic events. Following a period of seismic events on 30 July 2001, in which nine miners were temporarily entrapped at depth due to falls of ground in several parts of the decline, the mine operation was required to develop a seismic management system to mitigate seismic risk to the operation. A micro seismic systems and boundary element modelling of mine sequence highlighted large-scale footwall faults and the mining of gold bearing shear veins to be focal structures for seismic energy release between depths of 300 m to the base of mining at 650 m. The integration of seismic data, identification of geological structures and mapping of zones of failed rockmass led to the successful generation of a non linear boundary element model and a seismic hazard strategy. This enabled mine sequences to be assessed daily, monthly and periodically for potential seismic hazards and therefore assigned both economic and personnel risks for the recovery of the ore reserve at the Kundana Underground Operation.

Jan 1, 2005

By Bronson B

The geotechnical and environmental aspects of heap leaching are very closely tied during design, operations and closure. Potential environmental impacts from heap leaching are mostly due to land disturbance and water quality issues, including both groundwater and surface water. Water quality issues are mostly related to containment design, which is primarily a function of proper sizing of the facilities and site specific liner design. Geotechnical analyses is the dominant discipline in providing cost efficient, operationally effective and environmentally sound heap leach facility designs. Much has been published on geotechnical aspects of heap leach design, for example Van Zyl, Hutchison and Kiel (1988) and Van Zyl (1987). This paper will emphasize a few specific aspects related to the geotechnical and environmental consideration for heap leach projects. These aspects are: ò site investigation; ò containment design; ò slope stability; ò heap flow dynamics; and ò closure design. Design of a heap leach project must consider not only the operating life but also closure and post-closure considerations. As a matter of standard practice, designing for closure is an extremely important concept. Not only is it important for environmental aspects, but experience also shows that projects designed for closure will be overall more economical for the total life cycle of the project. Closure considerations are also important during project feasibility evaluations to ensure that total life cycle costs are evaluated.

Jan 1, 1994

By King ND

This paper presents an economic study comparing two gold recovery processes, zinc precipitation (Merrill-Crowe) and carbon-in-pulp (CIP). Capital, operating, and gold losses costs from an actual CIP plant study are compared to costs developed from a hypothetical Merrill-Crowe process flowsheet. ' Results indicate an overall economic advantage to CIP over Merrill-Crowe for plants processing slurries within the range of the five gold solution grades selected for this study.

Jan 1, 1982

By Paine G. G

The Red Dome Gold/Copper Mine is located approximately 15 km west of the township of Chillagoe which itself is approximately 220 km by road west of Cairns, Far North Queensland. The deposit, with other mines in the Mungana region, was worked from about 1901 to 1927. Exploration by Amoco Minerals Australia in the 1970s and early 1980s outlined a geological resource of 15 million tonnes. A mining reserve of 9.3 million tonnes was identified and originally developed by Elders Resources Limited. The mine commenced operations in March 1986 and was the first large-scale gold project in Australia to be developed solely on the heap leach process. The mine operated successfully as a gold heap leach operation until 1989 when new grinding, flotation and carbon-in-leach plant facilities were installed to process the non heap-leachable component of the orebody including the copper rich -ore. In March 1991, Red Dome Pty Ltd became a wholly owned subsidiary of Niugini Mining Limited. After six years of successful operation and having excavated a 200 in deep pit, it became evident in 1992 that unless more open cut reserves could be identified the operation was limited to six to nine months of high grade ore and a further 15 months of low grade stockpile material. A preliminary feasibility study was carried out to assess the viability of deepening the open cut. This indicated that from a technical and financial point of view it was possible to expand and deepen the open cut. This presented the daunting challenge of developing a 300 in deep, single access, open cut between a high chert ridge, a government railway line and a National Park. The meeting of this challenge is the subject of this paper.

Jan 1, 1994

Based on twenty years of experiences of applying computers in mine water engineering in Hungary, a program package was developed for home utilization and for other users abroad as well. This program package has been adapted to the CAD System of Coal Mining of COMECON countries. The main features of the "mine water subsystem" in the CAD System of Coal Mining and short descriptions of the key programs of the package are presented in this paper. Foreword The serious water problems of Hungarian mining pressed and/or stimulated its professionals to apply computers for supporting their problem-solutions. The first trials of these computer applications in mine water engineering were dated from the sixties. Owing to its twenty years of experiences in computer appli- cations in mine water engineering the Central Institute for the Development of Mining in Hungary was requested to work out the "Subsystem of Mine Water" for the Computer Aided Design System ('CAD) of Coal Mines in COMECON countries. This paper gives a brief presentation on the main features of this "subsystem"with reference to significant components.

Jan 1, 1988

By P Benjamin, H Bohannan, C Farr

Geoffrey Blainey's historical account of the mining activity on the west coast of Tasmania, æThe Peaks of LyellÆ documents the changes over 130 years of activity in the region. Commissioned by the Mount Lyell Mining and Railway Company, emphasis is placed upon the development of the Mount Lyell Mine in Queenstown. Chapter 19 æWidening HorizonsÆ details the review the Mount Lyell Company undertook in 1904/05 to ensure the future of the operation, following the pessimistic outlook regarding diminishing reserves and poor grade ore. The analogies documented between the Mount Lyell Company at that time, and Gold Mines of Australia 90 years on are remarkable, with both companies demonstrating a commitment to the Mount Lyell area through active exploration, the proactive search for alternative technology and the recognition of the valuable human resource. As Blainey writes (Blainey, 1993), æwith its expanding chemical works, its huge Tasmanian mines, its railways and smelter, its coke works and its mine crusade, Mount Lyell was probably one of the nation's five great industrial companies in 1906 or 1907. This brief phase of industrial and mining expansion had its seed in the threat of extinction . . .Æ After a number of reprieves, the Mount Lyell mine did stop production in 1994, but that only provided an impetus for a review and rebirth.

Jan 1, 1998

This paper presents a summary of the technical achievements of the Port Pirie Smelter in 100 years of lead smelting and refining. It also aims to give where possible the reasons or circumstances that led to the achievements. The major achievements took place in the areas of sintering, blast furnace, copper drossing, copper recovery, lead refining and slag fuming.

Jan 1, 1989

By C V. Putnis, T Geisler, A Putnis

In nature, ilmenite (FeTiO3) undergoes weathering through oxidation and removal of Fe to form an apparently continuous series of compositions from ilmenite to pseudorutile (ideally Fe2Ti3O9), and with further weathering, to leucoxene. To determine the mechanism of acid-leaching of ilmenite to ultimately form rutile, we have carried out an experimental study of ilmenite alteration in autoclaves at 150¦C in HCl solutions. Resulting products were studied by X-ray diffraction, scanning electron microscopy, electron microprobe and Raman spectroscopy. In some experiments the solution was initially enriched in 18O and the distribution of the isotope in the alteration products mapped from the peak shift in the Raman spectra. The results indicate that the alteration may proceed in two stages, each with a sharp interface between the parent phase and the product. The alteration begins at the original ilmenite crystal surface and along cracks through which the fluid can migrate. The first alteration product is pseudorutile û no phases intermediate between ilmenite and pseudorutile were detected. The textural relationship between ilmenite and pseudorutile suggests a coupled dissolution-reprecipitation mechanism rather than a solid state continuous oxidation and Fe diffusion mechanism. The second stage involves a further dissolution-reprecipitation step to form rutile. Raman spectroscopy shows that the 18O is incorporated in the rutile during the recrystallisation. Throughout the alteration process the original morphology of the ilmenite is preserved although the product is highly porous. The rutile inherits crystallographic information from the parent ilmenite, resulting in a triply-twinned rutile microstructure.

Jan 1, 2008