Search Documents

By Troman L, Groutsch J. V

The Kwinana Nickel Refinery began operations in 1970 processing sulphide concentrates from Kambalda using the Sherritt Gordon pressure leach and hydrogen reduction process to produce nickel metal as powder and briquette. Over the years a number of changes have seen the refinery capacity increased from the original design capacity of 15 000 tpa nickel on an all concentrate feed to its current design capacity of 42 000 tpa nickel on an all matte feed. This paper outlines the changes in plant equipment and process for the most recent refinery expansion from 35 000 tpa to 42 000 tpa which have been implemented since 1992.

Jan 1, 1996

Cyanidation tests by bottle agitation were conducted on an oxidized lead-silver ore containing approximately 12% Pb and 500 g/t Ag. Over 60% of the silver was leached when the ore was ground to 100% passing 0.15mm, whereas 50-60% of the silver was leached when the ore was only ground to 100% passing 0.5mm. Slurry handling and dewatering at the fine grind size were very difficult due to the high clay content of the ore, however this problem was greatly reduced at the coar- ser grind size. The silver recovery at the fine grind size was very dependent on cyanide solution strength with stronger cyanide sol- utions (containing more than 0.1% NaCN) re- sulting in lower solution silver contents. This was thought to be due to the precipi- tation of leached silver by zinc, which was also leached from the ore by the higher cyanide levels. There was a critical zinc level in solution of approximately 1000ppm, above which the silver recovery fell markedly. Cyanide and lime consumptions for this ore were high (typically 5 kg/t and 40 kg/t respectively), hence the processing of this particular ore by cyanide leaching is un- economic at current silver prices.

Jan 1, 1987

By D Morrison, P Goodman

The cycle time between adjacent stopes is critical to achieving the required production rate from 3500 Orebody; one of the Enterprise Mine orebodies. Current Mt Isa cemented fills require a 90-day cure period which had to be cut to 30 days while maintaining the required strength criteria. The Enterprise Mine Feasibility Study recommended that this be achieved by Cemented Slurry Rock Fill (CSRF), but that on-going research into paste fill be continued. The continuation of the research, in conjunction with overseas visits has recommended that the 3500 Orebody be filled with paste fill, with the potential to fill other orebodies. The paste fill will comprise cyclone and thickener dewatered copper tailings to which Portland Cement (PC) is added before vertical borehole delivery and undergound pipeline reticulation to individual stopes. The benefit is not only re-use of copper tailings but also much reduced binder usage.

Jan 1, 1998

By X Yang, T Zhang, Z Li, Z Yan, M A. Williams, S Qin, P Wilson

Continuous development of complex new steel grades to meet the ever-increasing demand of high performance causes recurrent issues in steel continuous casting such as surface quality defects (eg cracks, depressions, deep oscillation marks) and productivity challenges (eg faster casting, near-net shape casting). Continuous casting of steel is a highly successful metallurgical process. Much of this success can be attributed to the performance of the casting powder that is added to the top of the mould, creates a liquid slag pool as it is heated, and forms a slag film between the watercooled copper mould and steel shell during its passage down the mould. Mould powder selection is a compromise between the conflicting requirements of heat transfer and lubrication. In an EU RFCS (Research Fund for Coal and Steel)-funded project, various techniques are developed to offer the opportunity to adapt the slag film to meet the conflicting needs in different parts of the mould such that mild cooling can be generated in the meniscus, mid-broad face or corner areas whilst maintaining lubrication and offering higher cooling rates in other areas of mould. This has significant potential to address the industrial issues in product quality and productivity of continuous casting. This paper reports, as part of the EU RFCS project, the determination of crystallinity and porosity in slag films for casting challenging and innovative steel grades using new methods. In comparison with the methods such as X-ray powder diffraction (XRD) analysis and optical microscopy / scanning electron microscopy (OM/SEM) analysis that are currently adopted by the industries, EBSD (electron backscatter diffraction) has been employed to determine the crystallinity of the slag films taken from industry casters. X-ray computed tomography (XCT) plus 3D image reconstruction has been used to determine the slag film % porosity with pore volume, pore size distribution, and pore location, which can be linked with the performance of the slag films during casting different steel grades.

Jun 19, 2024

By S C. Bhowmik, R Gupta

This paper presents the ventilation problem faced by Jaduguda uranium mine, operated up to a depth of 905 m. The first two stages of the mine workings are up to 555 m, which are nearly exhausted. The third stage of the mine is from 555 m to 905 m and presently most of the stopping and development activities of the mine are carried out in the third stage. The total available intake quantity in the third stage was only 21 m3/s. As a result, the mine was facing a radiation hazard. The different instruments and the methods used for monitoring of radiation levels are also presented in the paper. It was observed that the average individual effective dose (external + internal) of radiation workers in Jaduguda mine increased from 6.93 mSv/y in 1995 to 9.5 mSv/y in 2001 and during this period the average individual effective dose of mine workers of the world was less than 5 mSv/y. Keeping this problem in view, a detailed ventilation investigation has been carried out in this mine. Initially the requirements of intake air quantity have been assessed by carrying out field investigation in different stopes and it was found that the third stage workings require nearly 100 m3/s. A detailed ventilation survey has been carried out in the total ventilation network and a basic ventilation model of the mine has been prepared. Different alternative schemes for effectively ventilating the third stage workings of the mine were simulated and a set of recommendations were made for implementation. The recommendations were partially implemented in 2002. As a result the total intake quantity to third stage workings increased to nearly 70 m3/s and the average individual effective dose (internal + external) of mine workers came down from 9.5 mSv/y in 2001 to 6.65 mSv/y and 6.60 mSv/y in 2002 and 2003 respectively. The implementation of remaining recommendations is in progress. Finally, a mathematical model has been formulated from the first principle for predicting air quantity requirements in cut and fill stopes in uranium mines and this model is being validated for further use.

Jan 1, 2005

By B G. Lottermoser

Phosphate induced stabilisation has been used to create passive iron phosphate coatings on pyrite and pyrrhotite. The formation of solid phosphate coatings on sulfide grains thereby inhibits sulfide oxidation. The aims of the study were to determine whether phosphate induced stabilisation could control sulfide oxidation and metal mobility in partly oxidised, polymineralic, sulfidic mine wastes. Waste materials were obtained from the acid mine drainage generating, abandoned Montalbion silver mine site, far north Queensland, Australia. The waste consists of quartz, kaolinite/illite, sulfide minerals (galena, chalcopyrite, tetrahedrite, sphalerite, pyrite, arsenopyrite), and pre- and post-mining oxidation products (hydrated Fe, Cu, Pb and alkali mineral salts). SEM observations of waste material treated with potassium orthophosphate showed that metal, metal-alkali and alkali phosphate coatings developed on all sulfides (with the exception of tetrahedrite). The abundance of phosphate phases was dependant on the availability of cations in solution for complexation with the phosphate anion. In turn, the release of cations was dependent on sulfide oxidation or the dissolution of efflorescent mineral salts. Experiments aiming to dissolve these phosphate coatings û using a strongly oxidising solution û showed that the phosphate coatings remained stable, preventing acid generation and metal release. The results of this study demonstrate that liquid phosphate stabilisers can suppress sulfide oxidation and immobilise metals in partly oxidised, polymineralic mine wastes.

Jan 1, 2003

By T Roberts, D Faulkner, G Watt

Traditional mechanised resin rock bolting in hard rock underground mines requires the installation of resin capsules into a pre-drilled hole prior to the rock bolt being spun into a hole to mix the resin and set the bolt in place. In poor rockmass conditions, especially at depth or in highly altered faults and shears, the condition of the holes often deteriorates as the poor ground around it unravels and falls into the hole. This results in partially or fully blocked holes that either damages the resin capsule when they are being inserted into the holes or prevent it entirely until the hole is continuously cleaned of debris. This deterioration of the hole condition, and continuous need to clean and re-drill holes, also increases the diameter of the hole which in turn affects the continuously mechanically coupled anchorage mechanism of the rock bolt to the rockmass as there is simply not enough resin in the hole to fill the annulus between the bolt and the rock. This results in a large increase to critical heading cycle time and, more importantly, results in the rock reinforcement not performing as per design specification and increases the risk of instability. To overcome the quality control issues with resin bolt installation in poor ground, a single pass drill, install, inject and tension self-drilling resin bolt application was designed and implemented for use in such conditions. This system allows the operator to inject a two part polyester resin through a self-drilled hollow bolt to mix and fully encapsulate the rock reinforcement. The self-drilling bolt allows for post injection of the hole after the bolt has been installed into the rock and gives the operator manual or automated control on the amount of resin used in the hole to ensure complete encapsulation and continuously mechanically coupled anchorage to the rock. This allows the reinforcement to work as designed and provide the Geotechnical Engineer extra quality control confidence in these conditions. The implementation of this single pass resin bolting system resulted in significant decreases to the resin bolting cycle time and rock bolt quality control failures. In this paper the design, implementation and embedment into the development cycle will be discussed and the in situ quality control checks used to validate the increase in rock bolt installation quality will be shared. CITATION:Watt, G, Roberts, T and Faulkner, D, 2018. Single pass drill, install and inject self-drilling resin bolt application in poor ground, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 323–343 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By A Hilli, K Kosmara, J Steyn

PT Nusa Halmahera Minerals (PT NHM) is an Indonesian joint venture company owned by Newcrest Mining Limited (75 per cent) and PT Aneka Tambang (Persero) (25 per cent). PT NHM operates two underground gold mines, Kencana and Toguraci at the Gosowong mine site in North Halmahera District, North Maluku Province, Indonesia.On 8 February 2016, a major ground movement occurred in the K-Link orebody of the Kencana underground mine, effectively blocking the only two access ways to the stoping area. Following mine clearance, it was found that a Solo production drill rig operator, who had been drilling in the Level 10 Extraction Drive was still underground, cut off from the rest of the mine by the ground movement.Communication, nutritional and logistic supply to the trapped operator was established with the breakthrough of two diamond drill holes. A range of technical expertise and opinions from both on and off-site were sought and two options were chosen for implementation of the rescue operation. The rescue was completed successfully on 16 February 2016 with the operator being rescued in good physical and mental health.CITATION:Kosmara, K, Hilli, A and Steyn, J, 2017. Eight days entrapped – PT Nusa Halmahera Mineral’s rescue of a trapped miner, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 155–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Linge H. G

The effect of sodium pyrophosphate and several polyacrylate deflocculants (Freevis 502, 528, 529 and 532; and Maxfloc 1015) on the gold loading on Calgon GRC22 and Norit R035l5 carbons was tested and found to be insignificant in a pulp free enviroument. These deflocculants can therefore be used in plants processing viscous gold pulps without fear of fouling the carbon.

Jan 1, 1990

By S Van Duin, I Porter

This paper discusses how advanced manufacturing technology (AMT), which is fundamentally reliant on and developed via multi-disciplinary skills, has benefitted non-mining industries, and what lessons can be derived from this experience to benefit the mining industry, particularly underground coal mining. Examples of AMT use in æconventionalÆ industry, some drawn from the more than 25 years experience in many different industries of the Automation and Robotics team at the University of Wollongong, are described to show typical benefits, risks and opportunities expected in using AMT. Applying AMT to mining brings many unique challenges and this paper expands on these and then provides practical examples of how a multi-disciplinary team can develop new processes and systems leading to productivity, safety and other benefits for underground coal mining.

Sep 26, 2011

Anglo Platinum recognised with its expanded operations the need to change its evaluation strategy due to increased sample volumes and the pressure it created at laboratories. The sender/receiver analytical scenarios had to change in order to curb costs and to prevent substantial investments in new sampling and analytical facilities. Given the high cost associated with correct sampling systems and sampling protocols and the shortage of technical resources a strategy of single point sampling and analysis was introduced. The analysis was then done at an ISO17025 accredited laboratory with ten per cent checks, subjected to careful statistical scrutiny. Logistical problems increased with respect to weighbridge congestion, maintaining sampling quality, throughput of samples in the sample preparation areas, manual quality control systems in place, audit trails and analytical capacity throughout all operations. This required the expedited improvement of existing sampling practices and the development of new sampling methods and equipment. Anglo Platinum is classifying and standardising sampling equipment, sample preparation and analytical procedures for all process streams with the view to minimise overall uncertainties. Major investments were made into a customised LIMS and automated equipment for data management, reduction of manual transcription errors and streamlining of sample processing. Anglo Platinum is committed in rolling out the enhancements to all sites as priority dictates.

Jan 1, 2008

The environmental and social responsibilities of the mining industry have long been recognized by the industry itself, but during the past decade it became one of the main targets for the more radical members of the community. This came as something of a shock to an industry which had always considered that it had acted responsibly within the standards of the day. As far back as early 1968, the Australian Min- ing Industry Council (AMIC) was clipping from newspapers the odd letter written by environmen- talists and critics of mining activities. In those days every such letter was carefully studied to ensure that AMIC, if not having the answers, at least had an understanding of the types of argu- ments then starting to be used against mining activity and in favour of environmental preserva- tion. Within 18 months, the infrequent letter to the editor had become a flood of such letters and feature articles, and the environmentalists' attack on mining activities had been launched in all its Vehemence.

Jan 1, 1978

It is well documented that drill and blast outcomes affect the downstream mining processes of loading, hauling, crushing and grinding but it can also significantly impact on mine profitability via dilution, recovery percentage, lump generation (iron ore), fines generation (coal, iron ore), coal loss and final wall stability. Drill and blast must therefore be optimised to improve the overall profitability via positively impacting on productivity and saleable product generation. It is however, difficult to achieve this because of the complexity of the number of parameters that must be integrated and managed across the entire mine value chain, ie the concept of æMine to MillÆ. This paper highlights, via a simple case study, the need to have a mineÆs drill and blast system both in control (so that it is predictable to a high degree) and with minimal variability (so the design actually makes it into the field). This type of management control is essential prior to optimisation work being undertaken. The æTeam ApproachÆ is discussed to illustrate the methodology of achieving drill and blast optimisation. A case study is presented to illustrate the potential benefits of this approach which in this mine represented a 27 per cent reduction in powder factor with the downstream functions achieving higher productivity with the same or reduced maintenance costs. It is essential for Australian mineÆs to implement the appropriate management strategies and experienced personnel placement to ensure that their mineÆs drill and blast system is correctly managed to facilitate the optimisation of profit. Without this, the Australian mining sector will become increasingly uncompetitive.

Jan 1, 1999

IN the ordinary course of treatment of pyritic ores or concentrates, whether for the recovery of copper, tin, gold, or any other contents, the removal of some or all of the sulphur contents is almost invariably the first step. The practice is to roast the ore in a current of air so that the sulphur is oxidized to sulphur dioxide and the metal constituents are changed from sulphides to oxides. If it is feasible to produce sulphuric acid in conjunction with the treatment process, the sulphur can be usefully employed; but if this is not possible, then the sulphur contents not only become a dead loss, but tend to be a nuisance as well in the surrounding neighbourhood.The problem of avoiding this disadvantage and making economic use of the sulphur has had attention from the early days of scientific metallurgy, and in the past few years very special efforts have been made both to drive part of the sulphur as such from pyrites and recover it, and to replace the sulphur in the S02 by carbon, with the production of carbon dioxide and precipitation of the sulphur. So far economic success does not appear to have crowned these efforts. In the case of pyrites, of the two atoms of sulphur which go to make the FeS2, the first is very lightly held. Dissociation is effected by heat alone at a temperature which is given by Peters as 5160 C.Now, sulphur and hydrogen will unite or burn together, with the production of sulphuretted hydrogen. It occurred to the writer that, if hydrogen was passed over pyrites heated to the above temperature, this first atom would be snatched away by the hydrogen, and could possibly be economically recovered.The first step consisted of some simple laboratory experiments. From these it was found that this first atom was readily removed, and that the extraction was practically complete. Further, the reaction took place at a low temperature, a dull red heat being sufficient.

Jan 1, 1923

By S Youds

The backfilling operation at Olympic Dam mine supports a 9.8 Mtpa underground Long Hole Open Stoping (LHOS) operation. It involves a combination of Cemented Aggregate Fill (CAF), surface rockfill and underground rockfill. The fill material is introduced from the surface via boreholes into the top of the stopes. Due to the deleterious effects of the dust and the thickness of the atmosphere in the stope it is not possible to view the filling process either at optical or infrared (IR) wavelengths. The need for a means to measure the filling process is driven by the placement of both rock and CAF fill in the stopes. The large volumes and high relative cost of CAF makes the minimisation of CAF fill a business priority. Incorrect filling can lead to the sterilisation of ore reserve. The use of millimeter wave radar to view through the haze to give real-time data on the relative positions of the different fill masses is being developed as an in-stope fill monitoring device. This paper reviews the salient points of the technology and its potential use in the backfilling operation at Olympic Dam. The broader potential of this technology for use in the mining industry by æseeingÆ through water and dust laden environments such as that found in stopes and ore passes is also discussed.

Jan 1, 2002

By K Sommerville

BHP Billiton’s Area C iron ore operation has been in production since 2003. During 2010, below water table mining in the Marra Mamba formation commenced and dewatered ore has been successfully processed through the plant.The ability to mine below water table material increases reserves. Pits can be dewatered using a combination of ex-pit and in-pit bores. Critically it is important to allow suffi cient lead time to dewater. For Area C, in-pit bores yield the most water which presents challenges in every day operations when mining around bores. Operationally there are steep learning curves in obtaining equipment, training personnel and setting up infrastructure. Core risks include lifting, refuelling and maintaining gensets. The pipework, extraction and re-establishment work can be very manual.The challenges include blasting, mining, stockpiling, processing, water balance and disposal. Maximising up time on bores whilst minimising impacts to blast practices have evolved. Blast practices now align bores to the edge of patterns. Protecting bores have evolved from stemming bores with rock and re-drilling to using gas bags which require no drills. Based on moisture and material properties, mining of dewatered material can be categorised into three groups:1. normal,2. sheeting, and3. sheeting and top loading.Ore can go straight to the plant ore to drying pads where it takes between one and three months to drain.Stock management of these piles is important to ensure efficiency of the plant. Rules have been established for blending wet material to maintain feed capacity and some modifications to plants have been made. Dewatering of pits poses a challenge for water use. Initially turkey’s nests were established to capture water and use for dust suppression. As water abstraction has increased methods of management include using exhausted pits for storage and evaporators. Managed Aquifer recharge and use in potable water are being considered. An over arching coordination of the capacity and use are required.Important elements in dewatering include:• capacity models,• capital,• long to short planning,• day to day coordination, and • water level monitoring and balances. Success in dewatering requires a cross function team working towards a common goal. *This is an abstract only. No paper was provided for this abstract.*

Jul 11, 2011

By J T. Carswell

Best practice mine sampling should provide a detailed quantification of all potential sources of error at each stage of sampling, sample preparation and assaying.Quality assurance (QA) should include testing for and quantifying potential sampling errors, and should be the basis for establishing ongoing sampling protocols, should set error limits and define quality control (QC) procedures. QA should be within the framework of Theory of Sampling (TOS) but may not involve the estimation of the sampling constant and the application of Gy’s formula.Best practice QC should be carried out efficiently and in a timely and cost-effective manner with regular reporting against the guidelines established by QA.This paper provides an assessment of, and checklist for, current best practice sampling QA/QC with examples from operating gold mines including the QA/QC of underground (UG) reverse circulation (RC) grade control.CITATION:Carswell, J T, 2017. Best practice sampling QA/QC for gold and base metal mining – including how to assess the applicability of underground reverse circulation grade control sampling, in Proceedings Tenth International Mining Geology Conference 2017, pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

Exploring for deep shallow dipping orebodies can be very expensive and very difficult. Surface exploration is often not an option and obtaining the best location for underground drilling can cause production delays if drilling is carried out from development headings. The Otter/Juan mine has been in production for approximately 34 years. All of the production is now sourced from more than 1000 metres below the surface from an area known as the Edwards Lode. The orebody is shallow dipping and open at depth. Exploration drilling has been performed from decline stockpiles and from hangingwall drill drives. Drilling from footwall positions (eg decline stockpiles) into shallow dipping orebodies can often produce intersections which are unusually thick thus leading to optimistic resource figures. The decision to develop a dedicated hangingwall drilling position can vastly improve the quality of the data used to generate an orebody model. In 1997 a new extension to the Edwards Lode was discovered and named the æFÆ surface. In 1999 a resource calculation was performed using data obtained from drilling that was carried out from decline stockpiles. In 2002 a dedicated drill drive was developed into the hangingwall of the æFÆ surface to obtain better data to verify the previous resource calculation. For this case study obtaining more representative data reduced the resource estimate by 66 per cent. This information was obtained early enough to allow for alteration to the mine plan and without loss of capital.

Jan 1, 2003

By H Zhang, Y Wang, S Sukenaga, H W. Ni, H Shibata, W Z. Mu

The crystallisation behaviour of low melting point CaO-SiO2-Al2O3-MgO inclusions greatly affect the deformability of inclusions during the rolling process. The crystallisation characteristics of CaO-SiO2- Al2O3-MgO melts representing the oxide inclusions in Si-Mn killed steel were systematically investigated. The effect of Al2O3 and MgO contents on the crystallisation change were analysed under a fixed CaO/SiO2 in the complex inclusions. The continuous-cooling-transformation (CCT) and time-temperature-transformation (TTT) experiments were conducted. The results showed that the increase of MgO content increases the crystallisation ability of CaO-SiO2-Al2O3-MgO inclusions, while the increase of Al2O3 content has the opposite effect. The viscosity, liquidus temperature of oxide melt and also the initial crystallisation potential might be the reasons for the change in crystallisation behaviour. Also, the crystallisation activation energy could semi-quantitatively characterise the crystal growth during the crystallisation of inclusions. To obtain low melting point plasticized CaO-SiO2-Al2O3-MgO (CaO/SiO2=1) system inclusions, the Al2O3 content of the system needs to be controlled larger than 15 wt per cent and the MgO content should be kept at a small amount.

Aug 21, 2024

Planning of modern mines entails considerable challenges in the areas of ground control, materials handling, safety, environment, equipment and personnel. Many orebodies are not economical unless efficient mining systems are used to win the ore. Relentless pressures are placed on mine operators to force them to become more productive and to make mines more competitive in modern economies. This has generated an intense drive to adopt technologies that rely on a greater degree of mechanisation, automation and computerisation. There is no turning back; high technology in mines is here to stay: computer controls and monitoring, computer aided mine design, information management systems, etc. During the past 20 years significant advances have been made in the areas of mine design, mine equipment and geomechanics. One could rhetorically ask if the advances in mine backfill technologies have kept pace with developments in other sectors of the mining industry. This paper will look at a few key mining technology sectors and will compare the relative progress of backfill technology to these sectors.

Jan 1, 1998