Search Documents

By Firth B. A

The classification performance of a Dutch State Mines (DSM) Rapped Sieve Bend has been investigated in a series of experiments. Coal slurries of a nominal 0.5 mm size were classified in the separation range of 0.10 to 0.14 mm at pulp densities from 6 to 21 per cent by mass of solids, and flow rates of 110 to 1375 litre min-1.The results obtained showed that the partition curve and water split io oversize was dependent on the solids flow rather than slurry flow rate or pulp density. For most of the operating conditions considered an accurate classification of the fine coal was obtained. The undersize efficiency was susceptible to solids flow rate, and was less than 70 per cent for solids flow rates greater than 16.7 tonne hour-1 metre-1 width of screen.

Jan 1, 1983

By Rixon K. L

Hargraves (1983) has reviewed the phenomenon of instantaneous outbursts of coal and gas with special attention to Australian occurrences. The purpose of this discussion is to highlight some problems and omissions in his review that reflect particularly on the authors' structural geological investigations of outburst-prone coal seams.It is surprising to find that much of the authors' reported work has either been glossed over or the results distorted by Hargraves (1983) and it is, therefore, important to clarify the contribution that structural analysis of coal seams can make.For many years it has been known that faults provided preferred loci for gas outbursts (for example, Briggs 1920-21) but the roie that faults played in outburstprone seams was unclear. The present authors reviewed the association of faults and outbursts drawing upon local investigations and the world-wide literature (Shepherd et aI., 1981), and discussed some wideranging aspects that result from the high coincidence of faults and outburst sites. Without repeating large segments of this article the authors will discuss four aspects of coal seam faulting and fracturing.

Jan 1, 1983

The authors describe two stratiform intrusions within a two miles thick ophiolite belt, one of the many ophiolite (serpentine) belts of the eugeosynclinal sequences of the Kalgoorlie System (metamorphic age c.2700 million years). Unusually good evidence of gravitational differentiation involving cumulates for an Alpine type peridotite-gabbro intrusion has been obtained, in spite of modifications of the original igneous rocks imposed by regional metamorphism. Unmetamorphosed relics of cumulate rocks are a surprising feature of this occurIfence.'fhe differentiation process reflected in the layered sequences is compared to that of the Stillwater Intrusion, Montana. Phase, cryptic and rhythmic layering are recognized. The economic significance of this study lies not only in the possibility of nickel mineralization in this ophiolite belt, but also in that much detailed information on the nature of these belts, which is difficult to obtain in the case of the more altered and sheared rocks of the belts carrying gold and nickel ore deposits nearby, is gathered from the Yilmia occurrences.

Jan 1, 1969

Mr. Chairman, distinguished guests, ladies and gentlemen. Thank you for asking me to your conference, with its most fundamental and appropriate topic of 'Investment in Mining'. I must confess at the outset that I am one of those Australians who has rarely visited your fair land of New Zealand. This is in fact only my third visit, with all three related to Institute Conferences, and all much too brief. In so many ways your country provides a counterpoise to ours, despite the obvious disparities in size and population. And I am not only referring to the Bledisloe Cup! We would certainly each be much more lonely without the other, in this strange long-lost corner of the globe û if globes can have corners. Such an important factor in common in our shared heritages has been the mineral industry we have won from our alluvials and our rocks û especially for gold. So much of the major mineral developments which have supplied the world's appetite for metals and fuels in the past two hundred years has come from the countries settled in that period by people from Europe, especially those from the British Isles. So much of the technology for mineral and metal extraction has come from the skills of those people in New Zealand and Australia. And so much of the further development of metal processing and manufacturing of productive equipment has come from those people and from their cousins throughout the world. It is, I believe, a fair question to ask why we have failed to build on those early and considerable successes, and why we have in so many ways apparently been so content to allow others to add value to our raw materials, and to take our technological developments on to levels far beyond those that our domestic markets could sustain.

Jan 1, 1988

The mineral processing industry is in boom times. The focus on mill availability and therefore profitability has never been greater, as grinding mill maintenance often dictates the entire plant shut down duration. Advances in mill systemsÆ quality and reliability and the faster, safer relining afforded by RMEÆs Mill Relining Systems have significantly enhanced grinding plant availability and utilisation. Yet relining performance is still affected by the design and planning by a team of stakeholders long before the maintenance team set foot in the mill. For a greenfield grinding plant project, these team players include: 1. project owner, 2. project manager, 3. mill supplier, 4. liner supplier, 5. plant operating personnel, 6. plant maintenance personnel, 7. mill relining crew, and  8. mill reline system supplier (RME). The complex and sometimes competing design demands of mill construction and operation together with the pressure of tight timelines can result in even simple maintenance requirements being overlooked let alone optimising plant design and planning for maintenance. This paper identifies all the involved stakeholders in an effective mill relining 'team' and gives principles and considerations for each to more effectively achieve the goals within their vital roles. This paper is aimed to be a practical guide for grinding mill designers and planners to more fully exploit the advances in Mill Relining Systems and improve their mill profitability.

Jan 1, 2008

By D Hill

In the Ngakuru area zeolite deposits occur in late Quaternary lacustrine vitric tuffs of the Ngakuru Formation and two of the deposits are being mined. The Ngakuru Formation overlies the Ohakuri Ignimbrite dated at c. 240 ka, and is overlain by younger alluvial sands and gravels. Individual zeolite deposits contain 50 - 80 per cent zeolite over a thickness of up to 45 m in thinly stratified vitric tuffs and are localised along NE-trending normal faults. Glass shards in the tuffs are replaced by the silica-rich zeolites mordenite and clinoptilolite. Amorphous silica (opal A), opal-CT, Kfeldspar and smectite are also present. The zeolites and other minerals are very fine grained (<10 8m), with open meshes of crystals that result in high porosities (52 - 70 per cent) in mordenite-rich tuffs. Zeolitic tuff samples typically have cation exchange capacities of 80 to 110 meq/100 g and internal surface areas of 25 - 58 m2/g, which combine to give high liquid and odour absorption capacities. The first zeolite deposit (Mangatete) was found in 1992, and this and the Twist Road deposit are worked by quarry benching into the side of hills. The zeolitic tuffs are dried and crushed to produce a variety of products including adsorbents for soaking up oil/chemical spills and animal wastes, animal feed supplements, water treatment, and sports turf and slow release fertiliser. The Ngakuru zeolite deposits formed at shallow depth (<100 m) along fault zones from reaction of glass-rich tuff beds with groundwater-diluted geothermal water during the late Quaternary, and are as young as 8500 yr BP from 14C dating of plant material in sinter associated with the Mangatete deposit.

Jan 1, 2005

The Archaeozoic Willyama Complex at Broken Hill has suffered several periods of deformation and metamorphism. New structural and petrological information together with that available from the literature gives a picture of the metamorphic evolution of the Barrier Ranges. Several epochs of metamorphism are recognized, and potassium-argon dating of minerals has been applied with limited success to the resolution of these epochs.INTRODUCTIONAdvancements in the mineral industry at Broken Hill over the past eighty years have been accompanied by a continual striving towards increased understanding of both the geological history of the Barrier Ranges and the environment of the Broken Hill ore deposits. However, although many detailed studies of selected localities and particular-aspects of Broken Hill geology have been carried out recently, the regional geology of the Barrier Ranges as a whole has received little attention from a petrological viewpoint since the pioneer investigations of Mawson (1912) and Browne (1922). There still remains a great need for regional surveys combining field studies of the habits, structures and outcrop relationships of the various rock types with laboratory investigations of their chemistry, mineralogy and microscopic ,fabrics. Recording observations arising from three brief visits to the Broken Hill area during 1959 and 1963 may stimulate further surveys.During one of these visits, the generosity of the Zinc Corporation Limited in providing field transport and geological guidance enabled the writer to collect material and study field relationships and appearance of the various rock types at numerous localities covering most of the Willyama outcrop. A complete study has not been conducted...

Jan 1, 1963

By Johnson T, Huynh D

The State Electricity Commission of Victoria is conducting a program of research and development into alternatives to the use of conventional boilers for the generation of electricity from brown coal. The objectives of the program are to reduce the cost of electricity generation and also to improve the thermal efficiency so as to reduce the emission of greenhouse gases and other pollutants. The program presently includes the following four technologies: Hydro-thermal Drying, Direct Coal Fired Gas Turbine, Integrated Gasification Combined Cycle, and Steam Fluidised Bed Drying. The Hydro-thermal Drying process produces a combustible coal-water-slurry fuel which is suitable for use in a coal fired gas turbine. The coal fired gas turbine has the potential to produce electricity at a lower cost than conventional power stations and when combined with a steam cycle, it will also use significantly less coal. The Integrated Gasification Combined Cycle process gasifies the coal, cleans the gas, and then bums it in a gas turbine/combined cycle. This process is being developed in Europe and the USA in order to meet their stringent emission regulations. It offers Victoria cleaner more efficient and cheaper electricity.

Jan 1, 1992

NATURE OF ORETHE Edna May ore consists mainly of clean quartz of a moderately hard and tough nature. The gold content is "free" and fairly coarse, so that a large percentage is recovered by amalgamation. The ore is practically free from metallic minerals.GENERAL OUTLINE OF PLANT AND TREATMENTThe ore, received from underground in trucks, is broken by a jaw breaker, then stamp-milled, follow~d by partial filie-grinding in pans. Mercury is used both in the mill boxes and pans. The pulp, on leaving the pans, passes over amalgamating tables and is then elevated by tailings pulp to cone classifiers and separated into a sand and slime product, each product receiving a separate cyanide treatment-sand by leaching in vats and slime by agitation and decantation in a "Trent" plant. Gold solutions from both sand and slime are precipitated together by zinc shavings in the usual type of precipitation boxes. Accumulated slime is trucked from the dam to a vortex mixer and from this point receives with the cement slime the same treatment.ORE BREAKING AND TRANSPORTThe ore is trucked from the brace of the shaft along an overhead line to the breaker station. Hence it is, by means of a "kick-up" dumped upon a grizzly, set with 2-in. spaces, the oversize being broken by a 15 x '9 Fraser and Chalmer jaw...

Jan 1, 1919

As in other countries, gold mining inNew Zealand has been cyclic in character. Looking at these cycles may provide insights as to what may occur in the future and that is the basis for this study.   New Zealand has experienced four gold mining cycles. The first began in 1857, peaked in 1866 and terminated in 1890. This cycle was characterised by alluvial gold mining by individuals and small groups. This is referred to as the Labour Led cycle. The second cycle began in 1890 and reached its peak in 1906 and terminated in 1929. This cycle was characterised by the use of dredges in alluvial gold mining and was also the peak of hard rock mining. This cycle is referred to as the Technology Led Cycle. The third cycle peaked in 1940. This cycle was far less significant than the previous cycles, arising out of the depression when the unemployed embarked on small scale alluvial mining. This overprinted the continuing decline that occurred after 1906. This cycle is here referred to as the Depression Overprint Cycle.   The fourth cycle began in 1984 when production began to climb rapidly from a very low base. The growth in production was spurred by rising gold prices in the early 1980s resulting in relatively low grade gold-bearing alluvial ground becoming economic. But in the 1990s, production from the new hardrock mines in Coromandel and Otago has overshadowed alluvial production. This cycle is here referred to as the Price Led cycle.   What are the future prospects for gold in New Zealand? Although there are many factors involved, this will be largely determined by two factors; firstly, continued access to prospective gold-bearing properties, and secondly, the price of gold. Based on these factors, three future industry scenarios have been developed. The first of these is industry collapse, in which access to prospective property is constrained and prices mayor may not weaken. The second is industry consolidation, in which the available ground is accumulated by a small number of large companies who can use economies of scale to weather price fluctuations. The third scenario is industry growth, in which access to prospective ground is constrained in environmentally sensitive areas but is otherwise relatively unconstrained. Efficient companies are allowed to work in a policy and economic framework that allows them to make a major contribution to the economy.   While the industry cannot control these critical factors, a good knowledge of the positive role gold mining could play in the future economy may provide a framework by which the access issue, in particular, may be addressed from a balanced perspective.

Jan 1, 1994

WHEN the writer resided at Zeehan, qn the West Coast of Tasmania, some years ago, he took a keen interest in the geology of the district and availed himself of the opportunity to investigate occurrences, of the varied minerals in which the field abounds. The following notes were compiled as a result of one of his periodical visits to the outlying mining districts, when an examination was made of the bindsay Reward tin mining property, which has an area of 140 acres. This is most easily reached from Renison Bell, the centre of the North Dundas tin-fields, on the Emu Bay railway, 'about' eight miles north east of Zeehan. Thence a pack track some 14 -miles long connects with the mine, crossing the Piemah River by a fine suspension bridge.The mine itself is situated on the main south leading spot of the Parson's Hood Range, at an altitude of some 1600 ft. above sea level. The Parson's Hood Range is composed of granite and is an extension of the rugged Meredith Range. A remarkable feature is the uniform topography of the surrounding country when viewed from the peaks. Except where dissected by the rivers and creeks, the surface is practically level and, indeed, affords a striking illustration of an ancient uplifted peneplain.The mine has been opened by means of trenches and adits, and the ore-body proved to extend for a length of 30 chains, with an average width of about 100 ft. Its general trend is west-north-west, and its dip, which is steep, corresponds to that of the country-rocks. These latter, which are of sedimentary origin and generally regarded as of pre-Silurian age, have been tilted at high angles, consequent, no doubt, on the crustal movements produced by the intrusion of the huge granitic masses which now form the high ranges in the vicinity.It may be here remarked that it is not Within the scope of this paper to deal with the sequence of events leading to the geological structure...

Jan 1, 1923

By Prasad S, Chatterjee S. S, Singh B. N

The chief source of metallic iron for steelmaking in India, even today, as it is in most part of the world, is through blast furnace (BF) route. This will continue to be so in the foreseeable future as the technology is most efficient, both process and economy-wise. However, as the world is moving into the next millennium, a critical look is being given to the process primarily because of its non-ecofriendliness (as a result of extensive use of metallurgical coal/coke requiring elaborate pollution control facilities) and huge investment involved for supporting facilities like extensive raw material preparation and handling, agglomeration, adoption of sophisticated instrumentation and control system, etc.

Jan 1, 1999

Possibilities for Flotation Acoustics Monitoring - A Review

Sep 13, 2010

Real Time and In Situ Measurement of Elemental Composition Using Lasers

Sep 13, 2010

By Larkin F, Farrer E, McGhie R. R

The Electrolytic Zinc Company of Australasia Limited commenced productive operations during February, 1936, at the- Rosebery and Hercules mines, which are situated near Rosebery, Tasmania. At this time it was decided that before re-organizing the steel sharpening shop a test should be made of the relative merits of conventional drill-steel and detachable bits. For this purpose Ingersoll-Rand type"I" thread centre hole.jackbits were selected and seventy-two of these were tested against conventional steel. Results indicated that, under the conditions pertaining at these mines, j ackbits should prove more economical than conventional drill-steel bits, and that a large-scale test, under working conditions, should be made. This was done by gradually replacing conventional drill-steel with jackbits at the Rosebery mine. Results were satisfactory and by the end of 1936 both mines were using only the jackbits.

Jan 1, 1939

By X Dahe

SLon vertical ring and pulsating high gradient magnetic separators (VPHGMS) possess the advantages of high efficiency and high reliability in beneficiating weakly magnetic minerals. In recent years, models SLon-2250, SLon-2500, SLon-3000 and SLon-4000 have been developed. This paper gives several examples of their applications in oxidised iron ore and ilmenite processing flow sheets to improve iron and ilmenite recoveries.CITATION:Dahe, X, 2017. Recent development and application of SLon vertical ring and pulsating high gradient magnetic separators in the iron ore and ilmenite processing industries, in Proceedings Iron Ore 2017, pp 461–466 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By A B. Christie, S C. Cox

Effective land-use planning requires accurate knowledge of mineral resource potential. Mineral companies during reconnaissance exploration, feasibility investigations and mine development also use this type of analysis. The Institute of Geological and Nuclear Sciences is undertaking a two-year project reviewing the resource potential of the West Coast of the South Island of New Zealand. Spatial prospectivity models have been developed as part of this resource assessment process, using computer based statistical pattern recognition techniques to delineate areas that are prospective for mineral deposits and to test deposit genesis models. Digital GIS data-sets of mineral occurrence were correlated against geology and exploration information. The distribution of mesotherrnal shear zone gold deposits in the Reefton Goldfield, were examined against geological data-sets from both the regional (QMAP) and local prospect-scale mapping. Weights of evidence analysis generated a correlation matrix that highlights relationships and degrees of association that might otherwise not normally be recognised.   Mesothermal shear zone gold deposits have strong positive spatial correlations with Greenland Group host rocks and areas with moderate to high quartz vein densities; moderate-strong positive correlation with regions <500 m from folds, with regions <600 m from faults and five to eight kilometres from granite contacts; moderate correlations with Ntrending fault and fold segments; and no/weak/poor correlations with fault intersections, fold-fault intersections, bends in regional structures and magnetic and radiometric data. The regional and prospect scale data sets give different results, with the more detailed prospect scale mapping giving generally better correlations. This emphasises the value of detailed geological mapping in the exploration process.   Maps generated by prospectivity modelling consistently highlighted areas of known mineralisation and generate targets where follow-up investigation is warranted. The prospectivity per unit area provides a measurable value that should change as new information comes to hand and, in addition to highlighting targets, can be used to measure the impact of increased exploration expenditure and assess the effectiveness of exploration investment.

Jan 1, 2001

By H Hutchinson

Froth flotation is applied to mineral sand concentrates in order to produce commercially viable xenotime concentrates. Experiments indicate that a xenotime product containing 38% Y2O3 at 47% recovery or 34% Y2O3 at 83% recovery can be obtained from a 27% Y2O3 feed. The process involves a primary stage of reverse flotation at which oxide and silicate gangue is floated, and secondary stage of direct flotation at which xenotime is floated. Of the various collectors screened an amphoteric compound was found to be effective at both stages. This was made possible by the addition of sodium silicate at the second stage, which acted as depressant for the remainder of the gangue. Similar studies on a low grade feed material were somewhat unsatisfactory as the grade achieved fell short of what was targeted.

Jan 1, 1990

Coal has become an enormously important export industry. Owing to a range of mainly natural advantages, Australia has been able to almost treble its exports in a little over the last decade. Australia is now the world's second largest exporter and coal is now the nation's largest single export earner.Despite this very significant growth, Australia's competitive position is in jeopardy.

Jan 1, 1984

This paper discusses support requirements for the proposed monorail system to be used in decline development. The monorail drilling and loading systems are systems that move on the rail (monorail) installed in the roof of the decline and supported by roof bolts, suspension chains and steel supports. However, due to the weight of the components of the two systems, it is imperative that the force in each roof bolt, suspension chain and steel support capable of suspending the weight of the heaviest component is determined. Numerical models that relate the weight of the monorail drilling and loading components to the required strength in the support system have been developed. Using these developed models, numerical values of the forces in each roof bolt, suspension chain and steel support, required to suspend the weight of the heaviest component of the monorail drilling and loading systems are determined.

Dec 6, 2010