Search Documents

By D Woolmer

Since January 2019, BHP Olympic Dam have been trialling the use of a drone based LiDAR mapping system for the purpose for surveying stope voids. This new technology utilises Simultaneous Location and Mapping (SLAM) algorithm providing positioning, stability and collision avoidance in GPS denied environments. Implementation of this system utilised underground personnel trained in the equipment’s use. The study’s intention was to evaluate the effectiveness of this equipment versus traditional surveying methods in regards to quality, safety and productivity. The trial results showed a marked improvement in the quality, productivity and personnel safety when conducting surveys. The use of the drone and LiDAR system reduced personnel and equipment requirements for surveys, thus allowing these resources to be deployed elsewhere. The technology’s simple and rapid deployment allowed multiple surveys to be conducted during a 12 hour shift, including ad-hoc work with minimal disruption to underground operations. After the drone’s initial trial, further work was conducted to utilise the Hovermap LiDAR scanner on other platforms to increase utilisation. A mounting system was created allowing the LiDAR to be mounted on a remotely operated loader or vehicle. This enabled drawpoint scans to be taken directly after production completion, resulting in faster stope close outs and drive scans for convergence monitoring. Implementation of the LiDAR system has resulted in improvements in the stope production cycle by reducing delays previously associated with data capture. The increase in the volume and quality of data has also allowed in-depth back-analysis of stopes in new mining areas to be conducted, which have driven improvements in the design process.

Mar 15, 2021

This paper reports the advances made during the development of underground mine fill technology from circa 1960 to the present and, in particular, indicates where increased input from process plant metallurgists û mainly milling, but also smelting û can contribute to further advances. Fill types pertinent to the discussion are partially deslimed, partially dewatered mill tailings fill (uncemented, cemented) and paste fill. Pertinent process plant includes hydrocyclones, thickeners, filters, elutriation tanks, holding tanks, mixing mills, pumps and pipes. Control instrumentation is a critical component of each of the process plant units. The impact of smelter practice on filling is not considered in this paper, except to note that some smelter slags are, or have the potential to be, active pozzolans and when ground to the specific surface area of Portland cement can act as partial Portland cement replacements, a factor of economic and operating significance when Portland cement supply lines are considerable and/or tenuous. The important role of process plant metallurgists has long been recognised, with Thomas, Nantel and Notley (1979) including them as one of the many categories of professionals with contributions to make. With the ever increasing sophistication of mine fill practice and its ever increasing acceptance as an essential component of the mining/ milling/waste disposal process, the scope for contributions by the modern breed of highly educated, specifically trained process plant metallurgists is becoming ever increasingly obvious.

Jan 1, 2006

PIP is regularly engaged in businesses where Greenfield Capital Projects are under- delivering on the expected business case. In most of these projects, we can identify that rigorous review has been carried out on the design and financial cost elements and substantial reporting is maintained to Boards on progress versus plan of project completion and cost. However, in all sites of this nature that we have worked at, the planning, design and execution of the operational elements or æwiringÆ of the organisation have fallen short and resulted in significant extra cost or opportunity cost (lost tonnage or quality) during start-up. When compared to the amount of planning and resources that have been poured into the capital side, the ledger on the æwiringÆ side is typically fairly sparse. This presentation outlines the importance of running a disciplined, rigorous process to prepare the human and wiring side of a start-up to ensure rapid start-ups and put the site on the pathway to high performance. It gives an outline of the rigorous process PIP has used with projects to ensure excellent start-ups.

Jan 1, 2006

By J Meikle

A projected image is not always a true representation of a situation, or indeed an industry. This is often the case of the mining and minerals industry, which has frequently been portrayed in a negative light with a male dominance stigma attached. However, these issues can be combated for both the industry and its future, current undergraduate students, through undergraduate industry experience. In particular, vacation work enables female students to dispel many myths surrounding the industry and realise that the mining and minerals field offers career development for both genders. This paper will discuss how vacation work enables students to make important career decisions even before they have graduated. Industry experience provides undergraduates with the opportunity to gain practical knowledge relevant to their field of study. Additionally it allows students to observe the nature of the industry and the sacrifices necessary to advance careers. The prior insights into an industry are relevant to all students, but particularly female students, who might otherwise be dissuaded from a career in mining. This paper is written from the perspective of two female undergraduate students studying Mining and Minerals Processing Engineering.

Jan 1, 2006

The control objectives and constraints for grinding circuits are ana- lysed, taking a single-stage ballmill-cyclone circuit as an example. The design of a hierarchical modular control system is described, for implemen- tation on modern microprocessor-based control systems. Product sizing measurement is identified as a problem area, and a new approach to product sizing inference, from on-line cyclone feed and overflow measure- ments, is presented. The procedure over-comes several practical difficulties of a previously proposed inferential method and is therefore expected to find application in more advanced grinding circuit control systems.

Jan 1, 1988

By K Sherry, N Shahbazi

Scope 3 emissions are a set of often overlooked indirect greenhouse gas emissions within a company’s value chain and represent the majority of emissions for many sectors. These emissions arise from activities conducted by entities beyond the reporting organisation’s ownership or direct control and are often challenging to calculate. Scope 3 emissions typically encompass purchasing goods and services, transportation and distribution, managing operational waste, downstream processing and utilising sold products. Within the mining sector, scope 3 emissions often constitute a significant portion of the overall carbon footprint. Therefore, these emissions are a significant aspect of the future of sustainable mining. As the journey towards a world committed to achieving Net Zero Emissions has started, the time to spark a transformative conversation in the mining industry has arrived. Consequently, a better knowledge of scope 3 footprints allows organisations to assess their emission mitigation projects against the total carbon impact of their operations and products.

Sep 1, 2024

By L I. Rozman

"There have always been development projects that fall short of expectations. In the last decade, we have seen more than the usual number of mining and oil/gas development projects taking significantly longer to develop and costing materially more than expected. The recent resource-equity market slump proves that investors are now far more cautious about investing new capital in the mineral and petroleum resources sector.What have we learned since 2005? Why have projects missed their targets? Why do investors often feel misled?Valuation of a project and the estimation of value is a more complex process than the evaluation of the merits of project development. The merit of project development can be clear from a prefeasibility evaluation, but this is no reason to skip the rigour of a feasibility study. The valuation of any project that is developed with any added risk should be discounted for this added risk.The development of a project impacts on other stakeholders, and the indirect cost of these impacts can have material implications for the cost structure, time and ultimate valuation of the project for its financial backers. The development of new projects (and thereby supply) can also have an impact on commodity prices, and therefore an impact on returns for financial backers.This paper will provide commentary on the author’s experiences and observations as a project developer and operator for 25 years, before becoming a project financier a decade ago.CITATION:Rozman, L I, 2016. Project evaluation and valuation – an investor’s golden rule, in Proceedings Project Evaluation 2016, pp 31–36 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

I have chosen this topic for my address with the intention of preserving a rather extraordinary record of recurrent additions of capital in the financing of one of the world's important silver-lead-zinc mines. The recitation of the trials and tribulations which fore-shadowed the rise of Mount Isa Mines to a position of relative prominence in the realm of non-ferrous mineral production may, I hope, be of assistance to some of the younger members of the Institute who may be called upon during their careers to meet similardevelopmental and financial problems.Mount Isa Mines Limited was incorporated in New South Wales in 1924 with an Authorised Capital of 40,000 shares of £20 each.In November 1925 the Company acquired the leases and water rights of the Mount Isa Proprietary Silver-Lead Limited for 6,250 fully paid £20 shares. Shortly thereafter, but in the same year, the £20 shares were split up into £1 shares, thus bringing the Authorised Capital to £800,000.The leases purchased consolidated and brought under one management the principal ore bodies of the Mount Isa area.Transportation facilities were indispensable to the economic future of the field, so the construction of a railway extending the Government line from Duchess, 54 ,miles to Mo.unt Isa, was assured by the passage of a bill in October 1925 by the Queensland Parliament. Under the provisions of the so-called Mount Isa Railway Act the Company was required to idemnify the Government against national loss on this branch line for a period of 10 years.

Jan 1, 1953

By N Arrys, A Jani, S Shahin

Optimising pit slope stability and reducing strip ratio of a mining operation are two key tasks in geotechnical engineering. With a growing demand for minerals and an increasing cost associated with extraction, companies are constantly re-evaluating the viability of mineral deposits and challenging their geological understanding. Within Rio Tinto Iron Ore (RTIO), the Structural Geology (SG) team investigate and collect critical data, such as point based orientations, mapping and geological inferences from adjacent pits to remodel deposits where previous interpretations have failed to account for structurally controlled slope failures. This work outlines the key methods utilised by the Structural Geology team which form the foundations of informed orebody knowledge and subsequent geotechnical design recommendations. This publication utilises the results from a recent analysis to highlight the benefits of this methodology and how it has impacted the economics of an operation through optimisation of a pit wall ‘cutback’ and crest relocation.

Sep 1, 2024

By M Jara, R Nuñez

As the global interest in sustainable energy sources has increased, lithium has emerged as a vital resource, playing a crucial role in the transition towards a cleaner and more efficient economy, but with this comes important challenges, especially associated to health, safety, and environmental matters. So, it is imperative for the lithium industry to prioritise HSE measures to protect workers, environment and surrounding communities. Implementing robust safety protocols and technology helps ensure the sustainability of mining operations and contributes to the overall responsible development of the industry. In this work we present how the Chilean lithium mining industry becomes a safer and more compliant industry using digital transformation (Cochilco, 2018; Bradley et al, 2013; Cabello, 2022).

Apr 16, 2024

In sizing of wet coal by the horizontal vibrating screen, screen openings to be used is much restricted, because coal is sticky and its bulk density is little. The electrically heated screen and other various types of screen had been tried to screen raw coal and coal as raw materials at a few mm. However, they failed to realize satisfactory results. On the other hand, fine sizing of coal is requested by many fields. For example, raw coal is desired to be screened at the fine rate, before being fed to the coal preparation control system in order to transport undersizes as unprepared coal particles and to reduce load in coal preparation waste water treatment system.1) Coals fed to the fluidized bed boiler also should be sized at a few mm. Regardless of many requests on fine sizing of coal, it seems that there are many cases to omit the basic screening process, because the screening is very difficult on a industrial scale. Size control as pretreatment of coal as raw materials is presented as one of the basic screening processes. In 1979, Kinki Industrial Co., Ltd. and Nippon Steel Corporation jointly succeeded in developing the vertical centrifugal screen. Closed -circuit crushing system by the use of this screen has operated actually at N.S.C, Hirbhata .Works, and realized the anticipated result. Consequently, this system has established the position as the most basic technology in the coal preparation. 2), 3), 4) This system has been also introduced to Nakayama Steel Works, Ltd. in 1982. This system termed the CPC (Coal Preparation Control) Process has been operated smoothly in both N.S.C. and Nakayama. Reported herein is the practical application of the vertical centrifugal screen termed V3-Separator. (V3 means vertical, versatile and vibration.)

Jan 1, 1984

By Chung S

The problems associated with equating calculated and measured properties of explosives with blast results are examined. The results from six full-scale test blasts in a limestone quarry are described. The purpose of the full-scale trial was two-fold, i) assess the role of varying aluminum levels (10% maximum) in a given explosive in terms of blasting performance, and, ii) find correlation between calculated, as well as measured properties of explosives and the resulting blasting performance. Each blast consisted of 36 holes, initiated with short period detonators in a staggered 3-row 2.4 m x 2.7 m (burden x spacing) pattern. Each 75 mm diameter borehole with no subgrade contained on the average 22 kg of 65 mm diameter cartridged explosive. The bench height was 6.3 m, with an average collpr of 1.2 m. The calculated and mgasured properties of explosive included, strength, detonation and explosion pressure, VOD, plate-dent depth, underwater bubble and shock energy, and the total energy efficiency. Each blast was instrumented to measure detonation velocity, initiation sequence, muck pile motion by means of high-speed photography and blasting vibrations. The post-blast measurements included photogrammetric survey of muck pile for size distribution on surface, muck pile profile, as well as the extent of backbreak. The results showed that the overall blasting performance of the explosive in question was nearly commensurate with the level of aluminum in the explosive, and there was excellent correlation between the underwater test properties and the blast results. The study also exemplified the need for more extensive post-blast analysis than is usual practice, for quantitative assessment of blasting performance of explosives and providing the necessary data-base for calibration of blasting models.

Jan 1, 1990

Sheaves are a critical safety component in a winding system and are expected to survive such extreme loading events as rope break. Sheave designs have often been developed and evolved empirically, consequently many existing sheaves are not necessarily subjected to the detailed analyses that are possible using todayÆs design tools. The design philosophy for sheaves is that the rope should be the weakest link in the system so that associated equipment can function safely for any load up to rope break. A number of failure mechanisms must be considered, but buckling is often prominent. During the course of investigating the feasibility of upgrading the hoisting capacity of a winding system, the capacity of all critical components was reviewed. The sheaves in the system were found to have insufficient spoke buckling capacity for the specified rope. A proposal to increase the spoke buckling capacity by connecting spokes together using a simple tie arrangement was evaluated and found ineffective. An alternative tie arrangement concept was developed and evaluated and shown to be adequate. This paper describes the finite element model, analysis approach and results for the original sheave and the two modifications. The contribution of the sheave rim to the total buckling capacity is evaluated. Some practical issues for spoke tie modifications are discussed.

Jan 1, 2005

Mobile mining equipment presents only a small portion (ten per cent mining project costs but the selected technology will determine to a large extent the mining performance and mine profitability. The actual performance of the selected mobile equipment technology will rely on the support functions, infrastructure, user interface and user acceptance. Optimising the technology to match the circumstances is an increasingly important phase in a mine feasibility study. Smartly done feasibility studies include the possible future needs of changing or building-up of the selected technology. In massive mining applications the machinery faces quite different challenges than in selective or small-scale mining applications. In massive mining applications the efficient and continuous move of large amounts of material has led to the use of increasing degree of automation. This higher degree of automation in a mining application, on the other hand, will be best applied to a smooth and streamlined mining process and operation. Mining methods like block caving support automated operation. Automated mobile equipment needs supportive infrastructure, monitoring and information transfer systems as well as well established working procedures. Too often the user interface and human factor is disregarded during the consideration of automation. Through the available supplier programming tools it is possible to see how much the selected technology provides flexibility in changing production or economical situations, when major rebuilds or replacements are necessary, and view the effects of all these on the mine economy. When adequate technology is available from various sources, the difference becomes from preparing for the future, managing costs and combining the best layout with the most suitable technological solutions.

Jan 1, 2000

By M E. Webb

Safety is a key value in most leading mining companies. Despite years of effort, and significant expense in ‘programs’, operating sites seem to have been left with no real improvement in either the elimination of fatalities or sustained reduction in injuries.Safety systems and processes have grown and evolved, often to the point where they have become overly complicated and marginally useful.MMG Limited, following the consolidation of its Australian operations under a single management structure, undertook a program to effect real and sustained change in its approach to managing safety. The program aimed at improving safety by better engaging its workforce and by making safety processes simple, useful and effective. It defined the role of the supervisor in creating safe work, the role of the people doing work and the role of safe work methods.A safety diagnostic tool was developed to assess site against safety-critical mindsets, behaviours, cultures and systems. The outcome of the diagnostic is considered by the organisation to be the true lead indicator of safety performance.While still a work-in-progress, the program at the Australian Operations of MMG Limited shows that challenging common paradigms in safety management can create real change in safety performance.CITATION:Webb, M E, 2016. Making safety simple, useful and effective, in Proceedings International Mine Management Conference, pp 217-223 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By Just J, Nguyen G, Dunn J. G, Graham J

A sample of pyritic gold concentrate was investigated by wet chemical and electron optical techniques. Sub-samples were roasted in a laboratory scale fluidized bed roaster in the temperature range 400-700¦C. The calcine was characterised, and cyanide-leached using a standard bottle rolling test. Gold extraction efficiencies varied with roasting temperature. At temperatures of 400 and 450¦C gold ex- tractions of less than 40% were achieved, but between 500-700¦C the extraction had increased to 93--98Z. The surface area of the calcine varied with roasting temperature, reaching a maximum at 500¦C. There was no correlation between the surface area of the calcine and the efficiency of gold extraction.

Jan 1, 1987

By R Winterberg

Concrete is a well established and reliable construction material for the permanent lining of tunnels, but shows some weak performance characteristics, which can be overcome by the addition of specialised fibre reinforcement. This paper addresses the particular performance design requirements of segmental linings, discussing the improvements of fi bres on concrete properties. Focus is made on the beneficial effects of fibre reinforcement on the cracking behaviour and the toughness performance, providing a safe and durable tunnel lining.Not only the mechanical performance of fibre reinforced concrete (FRC) for segmental linings, but also the durability of the linings has gained growing attention among the designers and consultants. Especially tunnel linings with exposure to media with corrosion potential, such as wastewater sewer tunnels or desalination plant outfall tunnels, have high requirements on their durability. The design of these structures must provide a comprehensive study of durability aspects. Fibre reinforcement can substantially improve the durability of concrete.Research has been carried out on the cracking behaviour of concrete. The beneficial effects of steel fibres on the cracking behaviour reduce the permeability by reducing the flow paths within the concrete. Crack bridging steel fibres create necking effects in bending cracks, leading to earlier closure of the cracks. Further, steel fibres create particular crack formations, which lead to a substantial reduction of the fl ow rates through separation cracks. The results also show that considerable cost savings can be achieved using FRC, as the thickness of the linings can be reduced.The durability design issues will be addressed and underlined by a case history on the Hobson Bay sewer tunnel in Auckland, New Zealand.

Mar 8, 2011

By Kagl J, Publlier M, Nekitel S, Arumba J, Rangin C, Mosusu N

Since the advent of plate tectonic modelling, the Ramu-Markham valley has been thought the site of a classical island-arc/conti- nent collision zone. In this interpretation the units south of the Markham Valley are held to be island are / micrcontinental mate- rial accreted to Australia and those north of the valley are thought to represent a separate Finisterre island-arc terrane. Recent remapping by the Geological Survey of Papua New Guinea shows: (1) there is no terrane boundary along the Ramu-Markham valley (2) the Finisterre Volcanics are probably part of either a fore-arc sequence or oceanic plateau obducted onto a microcontinent/ volcanic-arc composite terrane, accreted to the continental Australian plate. A new tectonic model is proposed for northern PNG and involves: (I) Eocene to Late Oligocene subduction below a microcontinent remote from Australia to produce the Sepik are and related intrusives, the Finisterre Volcanics (fore-arc or possible oce- anic plateau), together with the Alife blueschist. (2) obduction of the Sepik arc in Late Oligocene-Early Miocene times over the advancing Australian plate. This resulted in crustal melting, some of the products of which are the Mid- dle to Late Miocene Akuna and Bismarck intrusive complexes of the Maramuni arc. (3) obduction of the Finisterre Volcanics began in Early Pliocene times and continues today. (4) post-Middle Miocene mineralisation is the result of melting after obduction of the Sepik microcontinent.

Jan 1, 1997

By R H. Boffey

The Osborne copper-gold deposit was discovered in North-West Queensland in 1989. Underground production activities commenced at Osborne deposit in April 1996. This paper will examine technical and operational aspects of the underground mine during its development to a 1.2 Mtpa operation . Technical aspects discussed include geology, mine design and mining methods, equipment fleet selection and capital infrastructure. Operational aspects discussed include the evolution and performance of the integrated work teams that are utilised at Osborne to perform all mining and maintenance activities.

Jan 1, 1998

Peko Mines, a Division of Peko-Wallsend Operations Limited (PWOL) has operated several small underground mines in the Tennant Creek district of the Northern Territory supplying ore to a central treatment plant. The Argo Mine is the most recently developed by Peko Mines. A magnetic anomaly was identified from low level airborne magnetics in 1960 and drilling, which commenced on the site in 1969, was halted in 1974 and resumed in 1980 following the rise in the price of gold. By mid 1983 a resource of + 200 000 tonnes of 12 g/tonne Au had been outlined and a decision to develop the resource was taken following the drilling of three further diamond drill holes which did not significantly alter the value of the resource. The small size of the orebody could not support the full capital cost of two shafts and a single entry mine plan was developed to extract the ore at a rate of 15 000 tonnes per month and to provide all the safety features, ventilation systems and services of a two shaft mine. In December 1983 a contract was let to Allied Constructions Pty. Limited (Allied) to sink and equip a 4.8m shaft to a depth of 410m and to convert the headframe and winder, which are leased for the life of the mine by PWOL from Allied, from a sinking to a production configuration. Shaft equipment designed by Hardcastle & Richards Pty. Ltd. (H & R) in conjunction with PWOL includes a skip/cage, counter- weight, and an auxiliary cage on rope guides, a sealed ladderway and exhaust air ducts.

Jan 1, 1986