Search Documents

By Lott JB, Scuffham JB

Until very recently the application of solvent extraction to. the recovery of metals has been considered only for ithose operations where no other process was available. In general, .these operations, have involved metals such as 'f uranium or the rare earths, where the value of metal recovered has been very high. As a result, the tendency has been to consider solvent extraction as a very specialised, high cost technique with minimal application in the base metal industry. Since the mid-1960's this attitude has had to be changed drastically with the development of solvents specifically designed for the selective extraction of individual metals such.ascopper. The result is that solvent extraction must now be regarded as a proven hydrometallurgical technique for the recovery of base metals, and in particular copper. The first significant event in the application of solvent extraction to base metals was the production by General M. Inc. of a compound, designated LIX-63 (R)(1), which was a specific extractant for copper from ammoniacal sns. This did not find a wide application, however, because copper solutions with a pH in the applicable range we more readily treated by conventional techniques.

Jan 1, 1970

Economic and technical reasons forced the mining industry all over the world to increase the unit size of mineral processing equipment. in large flotation cells, this development leads to problems in areas of air dispersion and keeping solids in suspension. Outokumpu, an operating mining company, designed and developed a mixing mechanism for large flotation cells at its own concentrators and also studied problems related to tank design. Ideal conditions for flotation can only be achieved if the flow pattern created by the mixing mechanism fits well into the tank configuration and the risk of short circuiting is minimized. In large deep flotation cells, four different zones can be found which improve the behaviour of large cells when compared to small cells. Selectivity is increased and in some cases final concentrate grades can be produced from the rougher cell. The largest units have also been used as final cleaners in some installations. When modernizing old plants by installing fewer larger flotation cells, immediate and substantial savings in power consumption are achieved. Additional power savings are made in pumping costs because of simpler circuit design and decreased circulating loads

Jan 1, 1978

By D Corley, J Moore, M Grant, A, W R

Resource estimates are the corner stone of technical and investment decision-making. Prior to mining, resource estimation uncertainty has the greatest potential to lead to poor investment decisions, despite a significant component of resource estimation uncertainty being unknowable at this critical stage in the mining cycle. This presents a conundrum to the resource geologist in terms of risk evaluation and resource classification. Ahead of mining, there is normally considerable focus on drill hole spacing analysis to determine the ‘optimal’ drill hole spacing, taking grade and geological continuity into account; cost-benefit analyses balance improved resource definition against cost; the law of diminishing returns and the exponential cost increases acting together as spacing is reduced. Typically, a lower limit to the drill hole spacing is identified. After completing the resource drilling to an agreed spacing, resource estimation is then undertaken. At this point it is common to attempt to bracket the resource estimation uncertainty. In many cases conditional simulation is used, based on a modelled, but largely assumed, variogram model. It is also assumed that the histogram of the available drill hole sample data is representative of the in-ground mineralisation. The purpose of this paper is not to diminish the importance of drill hole spacing and simulation studies, but rather to illuminate an important aspect of estimation uncertainty that, although previously recognised, is typically overlooked – the question of how representative the available data set is in characterising the true (but unknown) distribution of mineralisation. To do this, we lift the lid on one of OceanaGold’s former operations, the mined-out Globe Progress Mine, by resurrecting a high quality, close-spaced, reverse circulation (RC) grade control data set. The Globe Progress Mine is within the West Coast Region of New Zealand, it was closed and transitioned to rehabilitation in 2016 and is now known as the Reefton Restoration Project. The exhaustive Globe Progress grade control data was used to repeatedly ‘redrill’ the deposit by extracting 35 m × 35 m spaced subsets from the original 5 m × 5 m spaced grade control data. Utilising closely spaced grade control data removed the need for assumptions regarding short range continuity, which are necessary with forward-looking analyses that are based upon broader spaced resource drilling. The extraction process used a nearest neighbourhood algorithm, repeatedly moving the origin in 5 mE, or 5 mN increments. Individual resource estimates were then completed for each of the extracted drill hole data sets (49 in total) as well as a grade control estimate based upon the exhaustive data set. Whilst the data unpinning each of the 49 estimates changed, the geological assumptions, variography, and modelling parameters remained constant. This approach was taken to isolate the impact of changing the input data. The 49 estimates were then compared against each other and the grade control estimate. The mean of all 49 sensitivity estimates was close to that of the grade control estimate in terms of contained gold, tonnes and grade. Whilst it is acknowledged that the grade control estimate itself is subject to some degree of estimation uncertainty, the close match between the average of the 49 estimates and the grade control estimate suggests that the resource estimation methodology is reasonable and appropriate. Whilst this comparison is important, the focus of this study is on the component of estimation uncertainty related to the underlying data, and this is reflected in the spread across the estimates. The spread across the 49 global estimates (highest to lowest) for this particular Mineral Resource Estimation Conference 2023 | Perth, Australia | 24–25 May 2023 142 case study was found to be significant (approximately 20 per cent in grade and metal) and that is attributable solely to the underlying data. This exercise quantifies a component of the estimation uncertainty that is inherent to all drill hole data and is distinct from the uncertainties associated with modelling methodology choices, sample and subsample quality and drill hole spacing-related interpolation uncertainty. Importantly, this uncertainty is unknowable prior to mining; we can only directly compare the resource drill hole data against grade control data after mining has taken place. For the case study, approximately 65 per cent of the estimates fell within 5 per cent of the grade control estimate for contained-gold, suggesting that for many projects the histogram of drill hole data is unlikely to differ noticeably from that of the in-ground resource. However, about 15 per cent of the estimates in this study differed by more than 7.5 per cent, suggesting that a not-insignificant proportion of estimates will be materially compromised. Whether or not the available drill hole data is representative comes down to the ‘luck of the draw’ and cannot be known at the time of resource estimation. Given the challenge of attempting to evaluate forward-looking estimation uncertainty, a component of which that can only be quantified retrospectively, what should we do as resource geologists? What are the implications for risk evaluation, resource classification and reconciliation? Furthermore, without rigorous post-mining data checks, resource geologists may conflate suboptimal modelling with the shortcomings of the underlying data. An example of this problem is discussed in the following section.

May 24, 2023

The object of this paper is to give an insight into various metallurgical operations involved in the making and shaping of steel for shipbuilding at the Newcastle plants of the Broken Hill Proprietary Co. Ltd., Commonwealth Steel Co. Ltd. and the Port Kembla plant of Australian Iron and Steel Ltd. Whilst not steelmakers, inasmuch as their processes start with semi-finished. steel supplied by the Steelmaker, the plants of Stewarts and Lloyds (Aust.) Pty. Ltd. and their associate company, British Tube Mills, Rylands Bros. (Aust.) Pty. Ltd. and the Newcastle and Kembla plants of John Lysaghts (Aust.) Pty. Ltd. make substantial contributions to the Australian shipbuilding industry, principally by way of boiler tubing and wires for welding rods and sheet steel, including special silicon lamination sheet for electrical motors.THE MAKING OF STEELThe making of iron and steel began as an accident, slowly developed as an art and has not yet become an exact science. The iron age dawned on the day when, by chance, man's primitive ancestor built up the wall of his fire with ironstone. In the ashes of the fire he found pieces of sponge iron from which he hammered out the first sample' of wrought iron. For many centuries iron ·was manufactured in bloomeries and occasionally, when the temperature was excessive, the iron combined with some carbon and steel was produced. But it was not till '1740 that steel was manufactured under controlled conditions. In that year Huntsman invented the crucible process which held undisputed sway for over a 100 years until in 1856 the invention of the Bessemer process revolutionised the whole industry.From then on, rapid progress was made. The Siemens...

Jan 1, 1951

By Z Terzic, M Schult, D Chu, S Macklin

The East West Link road tunnels are proposed to provide a connection between the CityLink toll road and the Eastern Freeway north of the Melbourne CBD. The alignment passes from Moonee Ponds valley beneath the Upfield Line railway cutting, Royal Park, the historic Melbourne Cemetery and beneath Alexander Parade rising to an eastern portal at Hoddle Street. The western (Royal Park) part of the alignment passes through the folded and faulted Silurian Melbourne Formation, which has been subjected to deep weathering since the Triassic.The Melbourne Formation in the Royal Park area is mainly characterised by interbedded sequences of siltstone and fine-grained sandstone. The beds are often graded and a clear boundary between the siltstone and fine-grained sandstone rock can be difficult to distinguish. Variation in lithology and the presence of structural geological features such as folds and faults have resulted in an irregular weathering profile within the Silurian rock; nonetheless the formation typically becomes less weathered with depth.Due to difficulties in obtaining reliable laboratory strength and stiffness relationships with weathering grade, in situ testing methods such as downhole shear wave velocity and high-quality pressuremeter testing are a useful aid to assessing appropriate geotechnical parameters for design.This paper presents an analysis of the variation in shear modulus of the Melbourne Formation, determined at small-strain (from downhole seismic data) and at ‘engineering scale’ strain (from pressuremeter tests) for extremely weathered (XW), highly weathered (HW) and moderately weathered (MW) rock. Estimates of small strain shear modulus (Go) obtained a range between 400 to 3400 MPa for these weathering grades. By comparison against the pressuremeter test data, reduction factors to be applied to these Go values to estimate shear moduli at engineering strain levels typically range between 0.10 and 0.35.The downhole geophysics undertaken in the Royal Park boreholes also suggests that there is an inversion in velocity between approximately 15 and 27?m depth below the top of the formation. This is thought to be related to the effects deep Plio-Pleistocene weathering, iron cementation of joints and increasing frequency of ‘non-healed’ joints in the transition from MW to slightly weathered (SW) rock.CITATION:Macklin, S, Schult, M, Terzic, Z and Chu, D, 2014. Strain-dependent stiffness of the weathered Melbourne Formation, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 179–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Warner N. A

There is an inherent problem in producing simultaneously lead, zinc and copper as metals in a single polymetallic smelting furnace. It relates to the condensation of lead and zinc from the gas phase under vacuum conditions such that metals in bulk form, either solid or liquid, are obtained as products rather than a fume or dust containing both metallic and non-metallic components. To understand this phenomenon, it has been necessary to establish mathematical models with computer simulation to identify the process requirements for effecting the objective of maximum bulk metal production with minimum fog formation. The theoretical framework of simultaneous heat and mass transfer involved in condensation from gas mixtures containing a non-condensable gas has been extended to the high temperature and reduced pressure conditions. These apply to new technology for polymetallic smelting now being developed in a project currently funded jointly by the Commission of the European Communities and the Mineral Industry Research Organisation. Under the right conditions it is theoretically possible to condense out both lead and zinc with minimal fume formation, but in all practical cases it is anticipated that some circulating load for reversion back to the smelter will be needed.

Jan 1, 1989

By Phelan JM

Poor selectivity in the separation of two sulphides generally arises because the flotation characteristics of the coarse sizes of the valuable mineral and finer sizes of non-valuable minerals are identical. Separat- ing the pulp into two size fractions at a specifically determined cut size and conditioning each size fraction with its own optimum reagent addi- tion is known to be helpful in improving such selectivity problems. The performance of the zinc section of the complex ore circuit at Wood- lawn Mines has been analysed in detail. The selective recovery of zinc was found to be a problem in zinc/pyrite separation. However, atypi- cally, the separation problem was between coarse zinc and coarse, not finer, pyrite. In spite of this the use of separate conditioning has effected significant improvements in rougher concentrate. Selectivity (and hence grade), overall recovery and flotation rate have all been enhanced. Dis- appointingly, coarse zinc recovery was not increased but, with careful optimization, this might be achieved without sacrificing the gains already realized. The technique of separate conditioning clearly has general application in other circuits where selectivity is a significant problem.

Jan 1, 1988

The title of my presentation is `Nursing One's Resources', words that fit a young organisation like Ross Mining and words we had to apply to reach our current level as a company. To get to where we are, we had to nurse, foster and treat carefully all our available resources in the widest sense of the word, namely: ò a stock or supply that can be drawn upon (funds, mineral resources, human resources); ò the means available to achieve an end; ò skills in devising expedients; and ò practical ingenuity. I do not claim that Ross Mining is now the perfect mining company. However, we have become a profitable, dividend- paying, gold mining and exploration company which is to our knowledge, currently the cheapest gold producer on the Australian continent. Nursing our resources got us where we are and will guide us in our future development. The words `nursing one's resources' are I feel particularly applicable to mining-as I like to argue that the extractive mining industry has a social responsibility to optimise the metal output and value from each orebody which is being exploited, and preferably leave no metal behind. Likewise, a modem company cannot survive into the future without maximising and optimising its human resource potential. In this presentation I would like to present a number of actual examples of nursing one's physical and human resources. Before I do that, I will give a brief background to Ross Mining. Ross Mining NL is a young Queensland-based company that gained its stock exchange listing in September 1987 and that poured its first gold in 1989 from its own developed Belyando Mine, located in Central Queensland. We have now reached the stage of a medium-size gold producer, producing approximately 70 000 ounces of gold per year, mainly from the Yandan Gold Mine, also in Central Queensland. Our production is set to increase to over 100 000 ounces in the near future. Recent increases in our resource base have secured us a future of ten to 15 years. As a young, newly listed company, we faced all the dangers that most new small floats do as a new entrant into an established industry. However, one advantage of being young and perhaps naive, is summed up by the following Zen Buddist saying: In the beginner's mind there are many possibilities, in the expert's mind there are few. A mining company's main assets are the sum of its resource base and the skills and talents of its people. Attempting to optimise both the physical and human resources within the company has been to-date the key to our success. The first example I would like to present is linked to the exploitation of the Belyando Gold Mine in Central Queensland.

Jan 1, 1995

By A Campbell

Open pit blasting at Ernest Henry Mining has the potential to cause damage to nearby underground workings. This paper is a case study of the blast vibration management project that was conducted to ensure open pit blasting did not adversely affect the stability of upper production levels or cause damage to the underground primary fan units. The two upper levels of the underground mine surround the lower portion of the open pit mine. The remaining underground mine workings are directly below the open pit mine. This paper details the process developed to prevent open pit blasting causing excess vibration in the underground mine. Measurement of test blasts combined with historic blast monitoring data was used to determine site specific blast vibration parameters. Threshold vibration levels for blast-induced damage to underground drives and the fan chambers were developed from benchmarking and non-linear numerical modelling. A Monte Carlo simulation model was used to predict vibration levels in critical underground areas. Blasts predicted to exceed maximum vibration levels could then be redesigned to avoid damage.A scale distance law for determining peak particle velocity (PPV) from the distance and charge weight of blasts was developed. Underground observations were used to develop a site-specific relationship between PPV and ground support/rock mass damage. A Monte Carlo superposition prediction model was developed and compared to measured data to refine input parameters. Standards for redesigning open pit blasts in order to reduce blast vibrations whilst minimising impacts on productivity are described. Non-linear numerical modelling was used to establish the dynamic capacity of the fan chambers, and set a PPV of 250 mm/s as a threshold for damage. The numerical model captured the full dynamic behaviour of the fan chambers and installed support, including transient stresses, strains and induced damage, when subjected to a simulated open pit blast.This case study also outlines a procedure for monitoring and predicting blast vibrations at other mine sites where open pit blasting has the potential to impact on a nearby underground mine.

Nov 8, 2011

By R Wynn, R A. Pax, S Mann, B Cornish

The semi-autogenous grinding (SAG) mill at the MMG Century operation has failing load cells that are essential to the control strategy used to stabilise the mill. Currently, mill-bearing pressure is used as a proxy for the load cells, but it has been found to be a noisy signal and lacking in useful sensitivity. It is also prone to variations and drift due to temperature. After consideration of a number of options, a non-contact acoustic array has been installed around the SAG mill to provide a more stable proxy load signal as well as other information about the internal operation of the?mill.The installation consists of 12 microphones to provide some detail into the operational differences that occur during normal operations at the MMG Century SAG mill. This acoustic approach acknowledges that operational grinding mills emit significant acoustic emissions that are a consequence of the dynamic environment prevailing inside them.Previous studies have attributed the acoustic noise to a range of events that occur inside these mills (Pax, 2011; 2012). Consequently, non-contact acoustic determinations of in-mill behaviour can provide powerful insights into the operation of the primary comminution tumbling mills. By measuring key microphone signal attributes at different positions around a mill, a holistic picture of mill internal operation can be developed.This paper will describe the installation of the 12 microphones and discuss the use of the acoustic load signals as a proxy for failing load cells. It will also present data from new observations of internal mill dynamics and the results of implementation of control using these acoustic signals. Key to the control approach has been the development of a logically coherent picture of the processes inside the mill.CITATION:Pax, R A, Wynn, R, Mann, S and Cornish, B, 2014. Implementation of acoustic arrays for semi-autogenous grinding mill?operation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 273–282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

Thank you and good morning. I am delighted to be here and to see so many of my colleagues and competitors. The general topic of this week's conference - World's Best Practice in Mining and Processing - suggests a focus on mining and processing. I am somewhat of a `jack of all trades and a master of none'. But I'm not even a jack when it comes to mining and processing technology and practices, and so I will leave those topics to speakers better 'qualified than I. Instead, what I would like to do is give you my thoughts on the best management practices of mining. You see, the times are changing for the mining business. There is great uncertainty in our industry. Anyone who received their education in an English-speaking school probably remembers the famous poem `Invictus' by William Ernest Henley. The two most famous lines from that poem are, if you remember, `I am the master of my fate; I am the captain of my soul'. The fact of the matter is that the metals industry, including the copper industry, is not the master of its fate. To a great extent we're at the mercy of forces over which we have little control, such as the world economy or political situations in individual countries. The copper industry is like a surfer at Manly - we can't influence where the wave is going; all we can do is stay in front of the curl and on our board. Historically, discovering, developing and processing ore reserves were the primary facets of our capital intensive business. To stay competitive today, we must invest equally in intellectual capital - our employees - in order to succeed in the face of economic, regulatory and political challenges and global competition (Schonberger, 1986). Everyone seems to have a different theory about being competitive. A lot of people use sports analogies when talking about competition. Others, like American businessman and former US presidential wanna-be Ross Perot, take a more interesting approach. In Mr Perot's hypothetical corporation, competition is a lot like having a snake in a factory. If someone sees a snake, the first thing they do is create a committee on snakes. Then, the committee on snakes meets and discusses the problem for a couple of years. The most likely course of action is nothing. Everyone figures that the snake hasn't bitten anyone yet, so they just let him crawl around the factory floor. Perhaps a vice president of serpentine affairs is appointed to continue watching the snake - making sure it doesn't grow. Ross Perot sees it a little differently. In his corporate world, business needs to build an environment where the first guy who sees the snake kills it. Of course in our industry, we better make sure the snake isn't on an Endangered Species List before we go after it! I am not going to talk about competition and competitive forces in terms of sports or snakes, but I would like to share some thoughts with you about how the mining industry can better utilise competitive thinking to get ahead and stay there. You may be wondering how an executive from a 160-year-old company could know much about competitive spirit, but the founding ancestors of Phelps Dodge were wizards at identifying

Jan 1, 1995

By D A. F Oliveira, C J. Parker

The role of the virgin in situ stress field in tunnelling projects is well known in the Sydney area. The effect of in situ stresses is mostly considered through the use of published relationships that describe the in situ stress conditions as a function of depth. Considering the significant scatter in the data, it is evident that by adopting such relationships, the designers are assuming an average distribution of stresses with depth that is generally a reasonable engineering approach; however, when building a geomechanical model, the tunnelling or geotechnical engineer needs to account for the interrelationship between ground conditions (rock mass quality – fracturing, strength and stiffness) and in situ stress, which may explain part of the stress data scatter. This paper presents an alternative approach for interpreting in situ stress conditions, valid for both Sydney sandstones and shales that focus on such interrelationship between in situ stress and ground conditions.CITATION:Oliveira, D A F and Parker, C J, 2014. An alternative approach for assessing in situ stresses in Sydney, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 189–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By D Teyhan, J Kirsch

Traditionally, most Australian iron ore mining operations have been surface-based. Processing plants were designed to handle dry ores. In recent years mining operations in the Pilbara have progressively moved below the water table exposing wet, sticky ores which have caused lost efficiency in screening operations as particles tend to agglomerate and adhere, blinding screening media. Miners and vibrating screen manufacturers have experimented with a shift from linear motion to elliptical motion screens. Elliptical motion conveys and lifts particles. Effective on flat deck (horizontal and inclined) or sloping decks it can be configured to provide a controlled transport rate, applying pressure in all directions to maximise screening efficiency. In practice, elliptical motion screens have proven to be effective in dislodging sticky particles from screening media, reducing blinding rates and improving screen efficiency. Moisture and clay content change during the life of a mine. These changes are sometimes the effect of seasonal rainfall, in other cases due to increased groundwater and clay content as mining operations go deeper. To compensate for such changes and optimise screen efficiency, changing the ‘shape’ of elliptical screen motion is required. This has traditionally required shutting down processing plants and making mechanical screen adjustments. Plant downtime is costly and machine adjustment has been a ‘trial and error’ practice. This paper will explore the results of a field trial that is currently underway in Brazil of a next generation elliptical motion screen design that allows operators to make changes to exciter rotational direction, speed and screen stroke angle, through electronic drive phase control. The machine’s electronic drive system synchronisation is enhanced for stability with a unique mechanical timing system. Operating at up to 6 g, screen adjustments can be made on the fly without stopping production. Early trial results are showing up to 50 per cent improvement in screen efficiency compared with traditional elliptical motion machines under certain feed conditions.

Nov 8, 2021

By O S. Maluleke

In some deposits valuable heavy mineral quality is poor due to increased mineral surface coatings from higher slimes and more competent sand orebodies. Mineral surface coating can include silica or aluminium rich clay minerals and iron based minerals that render the final product quality off-specification, in this case specifically ilmenite and zircon. Conventional physical beneficiation processes such as magnetic separation, electrostatic separation and gravity separation are not able to remove these surface coatings. Surface dependent separation techniques such as electrostatic separators are affected by these coatings which hinders the rejection of non-valuable mineral from product. Attrition scrubbing is the most commonly used technique to reduce surface coatings, using mechanically induced particle to particle interaction, abrasion and shearing.In many cases it is a challenge to measure the surface removal efficiency of these scrubbing units. Elemental analysis techniques (ie X-ray flourescence) (XRF) in a multi mineral environment are unable to measure surface impurity reduction with enough precision. Mineralogical analysis (in this case Qemscan®) has constraints in terms of sample preparation with highly coated particles being plucked out during block polishing. This paper suggests a combination of laboratory separation techniques coupled with elemental analysis to evaluate the surface removal efficiency. Three different types of feed materials were used to analyse the efficiency of surface removal using production attritioner scrubbers. This approach relates the downstream beneficiation plant’s expected performance with that of the attrition scrubber’s scrubbing efficiency.

Oct 5, 2011

At Renison Limited, on the West Coast of Tasmania, modern trackless decline mining is practised to exploit the various tin bearing sulphide deposits. With footwall accesses, one of three adaptations of horizontal mechanised cut and fill, 1. unsupported, 2. pillar supported,and 3. unsupported - resuing is used to stope each defined ore block. The stoping method is basically determined by the dip and true thickness of the ore with emphasis on high ore recovery. Extreme flexibility is possible by the selective mining of stope lifts, the consumption of development waste as fill and the utilisation of the same mobile equipment in all phases of production. This has resulted in high productivity and low cost per tonne of ore.

Jan 1, 1977

In 1556, Agricola noted that "a prudent owner, before he buys shares, ought to go to the mine and carefully examine the nature of the vein, for it is very important that he should be on his guard lest fraudulent sellers of shares should deceive him"(1). In today's world, the owner rarely has the opportunity to visit the mine and, instead of reading about the `nature of the vein' in annual reports, prospectuses, government publications, et cetera he sees the words `reserves' and `resources'. Unfortunately, the subject of reserves and resources has become increasingly complex and Canadians, along with their counterparts in Australia and elsewhere, are still struggling with definitions which will attempt to cover all conceivable circumstances from national or regional resource endowment to the material to be extracted next week from a given stope or open pit bench. The providers and recipients of reserve and resource data are: - Government agencies who are concerned with questions of national endowment, strategic use of raw materials and other questions of public policy. - Stockholders who have a vested interest in the basic assets of their companies. - Financiers who are concerned about the security of their loans. - Regulatory bodies whose function is to protect a frequently naive investor from unscrupulous practices. - Management, at head office and on-site, who need basic information for decision-making, whether it be to open up a new mine, expand or close an existing operation, acquire or merge with other entities, or, more mundanely, for routine mine planning. To satisfy their demands with unanimously accepted definitions is a formidable task but, it is my impression that, little by little, a concensus appears to be growing within the industry.

Jan 1, 1987

By Robins R. G

The dissolution of metallic copper powder in aqueous solutions of cupric sulphate under the influence of ethylene gas was investigated. The dissolution reaction stoichiometry obtained was: Cue+(aq) + Cu(s) + 2C2H4(g) = 2(CuC2H4)+(aq) The rate of formation of the copper (I)-ethylene complex in the above reaction was studied in a laboratory autoclave and the effect pH, temperature, ethylene partial pressure and initial concentration on the dissolution rate was measured experimentally and expressed theoretically in terms of several simple conceptual kinetic models. The results led to the selection of optimum conditions for the reaction and the suggestion of an "ion-molecule reaction" mechanism to explain the very low activation energies for the reaction system. The area of application of this reaction lies in the direction of refining impure copper such as cement copper. Several experiments were performed in which an acidified solution of cupric sulphate under ethylene pressure was used to dissolve copper from the cement copper powder in the form of the copper (I)-ethylene complex, followed by the release of gas pressure to disproportionate the complex and precipitate a purer metallic copper.

Jan 1, 1987

By D Teyhan, J Kirsch

Traditionally, most Australian iron ore mining operations have been surface-based. Processing plants were designed to handle dry ores. In recent years mining operations in the Pilbara have progressively moved below the water table exposing wet, sticky ores which have caused lost efficiency in screening operations as particles tend to agglomerate and adhere, blinding screening media. Miners and vibrating screen manufacturers have experimented with a shift from linear motion to elliptical motion screens. Elliptical motion conveys and lifts particles. Effective on flat deck (horizontal and inclined) or sloping decks it can be configured to provide a controlled transport rate, applying pressure in all directions to maximise screening efficiency. In practice, elliptical motion screens have proven to be effective in dislodging sticky particles from screening media, reducing blinding rates and improving screen efficiency. Moisture and clay content change during the life of a mine. These changes are sometimes the effect of seasonal rainfall, in other cases due to increased groundwater and clay content as mining operations go deeper. To compensate for such changes and optimise screen efficiency, changing the ‘shape’ of elliptical screen motion is required. This has traditionally required shutting down processing plants and making mechanical screen adjustments. Plant downtime is costly and machine adjustment has been a ‘trial and error’ practice. This paper will explore the results of a field trial that is currently underway in Brazil of a next generation elliptical motion screen design that allows operators to make changes to exciter rotational direction, speed and screen stroke angle, through electronic drive phase control. The machine’s electronic drive system synchronisation is enhanced for stability with a unique mechanical timing system. Operating at up to 6 g, screen adjustments can be made on the fly without stopping production. Early trial results are showing up to 50 per cent improvement in screen efficiency compared with traditional elliptical motion machines under certain feed conditions.

Aug 24, 2022

The refractory industry in New Zealand is small, consisting of two main manufacturers - one at Huntly and the other at Kamo. Together these would have an annual refractory production of about 30 000 tonnes. The industries which use refractories include two steelworks, NewZealand Steel Limited and Pacific Steel Limited, the former is involved in continuous casting from sponge, iron and scrap steel and the latter is involved in ingot teaming from scrap steel and steel billets; One aluminium smelter, cement works, dairy companies, small foundries producing engineering requirements and many other small users. The New Zealand manufacturers produce refractories in thefire brick range, that is up to 50 per cent alumina content (ignited basis), based on indigenous raw materials and in the high alumina range up to 85 per cent alumina content (ignited basis) based on imported bauxites. All of the basic refractories high purity silica and high alumina low alkali refractories and many of the higher grade acid resisting refractories are imported.

Jan 1, 1976

By R. A. Frith, M D. Goodz

Ore-bearing minerals that are located along microfractures are always susceptible to loss during the breakage and sampling of the material. Further losses occur with on-site sample preparation and splitting prior to laboratory analysis. In these cases solid whole rock channel or core samples should be handled with due care to ensure all fines and loose particles are collected and included in the sample for total chemical analysis.Similarly open hole and reverse circulation drill methods are not usable in areas containing old mine workings, heavily fractured ground or highly degraded/oxidised mineral assemblages. Nor are these methods usable to assess a bulk mineable target where the enriched zones were peripheral to or between old mine cavities.

Jan 1, 1993