Search Documents

By S C. Dominy

Gravity amenable gold ores are those that after comminution produce liberated particles, composites and/or carriers that can be recovered by gravity separation means. Recovery depends upon mineralisation type and the comminution and concentration method used. Any in situ ore with more than 20 per cent of gold greater than 100 µm in size is likely to have a strong gravity recoverable component. A less traditional approach is where the gold is sulfide-locked and the gold carrier plus any liberated gold is recovered via continuous gravity recovery following fine crushing. Specific tests are undertaken to determine the level of gravity amenable gold within a deposit. The principal methodology is the gravity recoverable gold (GRG) test, which consists of three sequential liberation and recovery stages. For continuous gravity recovery (CGR), the sample is fed over a laboratory Wilfley table to simulate continuous recovery of the gold. Tails from the feed can be progressively re-ground and re-tabled to develop a grade-recovery curve. Primary geology and gold particle size-distribution have a strong effect on the mass of sample required to provide representative results for both tests. Where low-grade ore contains very coarse gold, substantially larger sample masses are required. Experience has shown that GRG and CGR values can vary throughout an orebody, particularly within different geological-grade domains. A testing regime must consider sample frequency and support.

Sep 5, 2011

The South Wall Base Case Design for Mt Whaleback indicated that along portion of the South Wall a cigar shaped synclinal keel, contain- ing 14 800 m', of Dales Gorge Member ore, would be unkeyed and bed- ding undercut. The dry "ore lobe" slope would be 60m high, unbenched and approximately 170 m long. Stability analyses using specific design parameters established that artificial reinforcement could stabilise the slope and be economically justifiable. To implement the slope design reinforcement for such a complex geo- logical structure it was necessary that all functions pertaining to slope excavation be integrated and co-ordinated within the Mine Geotechnical Section. The objective being to minimise slope damage and thereby optimise the effect of design reinforcement. The successful excavation of the ore lobe in 1988, three years after the introduction of artificial reinforcement, was achieved by strictly main- taining the following parameters. 1. Accurate Geological Model 2. Controlled Perimeter Blasting 3. Controlled Excavation Techniques 4. Quality control -Reinforcement Installation 5. Additional Reinforcement.

Jan 1, 1989

By Vilela A. C F

In the present work, the process of dephosphorisation of stainless steel was developed in laboratory scale by adopting a high frequence induction furnace, using BaCO3 base flux. By using BaCO3 - CaO - BaC12 - Fe2O3 Flux of about 110 g/Kg-metal, 30 per cent dephosphorisation degree was obtained a stainless steel containing 18,8 per cent Cr and carbon between 0,08 and 2,0 per cent. In addition, a dessulfurisation degree of 89 per cent was achieved too.

Jan 1, 1991

By Dickson T. J

Slag cleaning is an important part of the pyrometallurgical operations at the Kalgoorlie Nickel Smelter. It is a complex system with many streams of different phases and composition. Some of these streams are very difficult to control and/or monitor. Through the use of a statistical computer package, called Minitab, key relationships affecting the economical operation of the slag cleaning process have been found. Data for the statistical analysis was collected from all possible variables around the appendage.

Jan 1, 1991

By A Tawadrous, B Wheeler, D S. Preece, S A. Silling

The two key results of rock blasting are fragmentation and movement of geomaterials. Movement/flow of the blasted rock is often referred to as heave. Moving rock with explosives rather than mechanical equipment can improve mining efficiency. Such is the case with coalmine cast blasting. Controlling and directing rock movement through explosive deck delay timing can greatly improve ore recovery by segregating ore and waste. In both cases, understanding, predicting and controlling heave is an important element of successful blasting.Computer programs for predicting 2D blasting-induced heave have been used in mining for decades, helping to drive the innovation of new and more efficient mining methods, ie cast blasting. The past few years have seen the advent of 3D distinct element modelling of blast-induced heave. This is an important advancement because most blasting situations are three-dimensional in nature, especially when controlling the direction and intensity of rock movement through explosive deck delay timing.This paper documents the first full-scale blasting simulations in 3D with distinct element models that include hundreds of blastholes and in excess of a million particles, made possible with parallel processing. Surface mineral blasting is the focus of this study which treats the effect of blasthole delay timing on ore recovery. Ore waste and dilution resulting from typical row-on-row delay timing will be demonstrated. Also demonstrated will be the ore recovery possible with delay timing designs that significantly enhance ore/waste segregation. This type of high fidelity modelling and the use of electronic detonators makes possible the sculpting of rock blasting muck into separate piles of ore and waste.CITATION:Preece, D S, Tawadrous, A, Silling, S A and Wheeler, B, 2015. Modelling full-scale blast heave with three-dimensional distinct elements and parallel processing, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 127–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Conditional simulation can be used to determine the probabilities of block iron-grades being above selected cut-offs. However, there are much faster alternatives that can produce acceptable results. In this paper blasthole data from a selected area of Joffre Member hosted ore of the Brockman Iron Formation at the Mt Whaleback orebody is used as the basis of a case study to assess alternatives to simulation. Iron grade, in per cent, is interpolated from a blasthole dataset into a block model using ordinary kriging. Samples are then removed from this blasthole dataset to produce data subsets. A complete distribution of iron grades for points or blocks is obtained utilising the data subsets and the following techniques: conditional simulation, median indicator kriging, the probability from conditional expectation and confidence intervals attached to the estimation of blocks in the framework of the discrete Gaussian model. The complete blasthole dataset is considered to represent the true iron grades at sample point support while the ordinary kriging estimate derived from these samples is considered to represent the true block grades. The distributions obtained from point estimates, block estimates and simulations are compared to each other and to the true estimates of iron grades using graphs and statistics. The conditional expectation technique reproduced the results obtained from conditional simulation extremely well and it is a viable alternative to simulation at point support. At block support the confidence intervals technique reproduced the results of the conditional simulation more closely than the median indicator kriging and in the data subsets tested the confidence intervals technique actually reproduced the true grade distribution more closely than the conditional simulation.

Jan 1, 2005

By B Lumsden, R Smiles

Independence Group’s Jaguar Mine treats a polymetallic ore producing a copper concentrate and zinc concentrate. Effective separation of the sulfides requires relatively fine grinding with flotation feed P80 of about 75µm. Zn losses to final tails are greater than 60 per cent and <32 µm. When magnetic conditioning was first installed in 2010 it showed about an 8 per cent reduction of zinc in final tail and on some ores a similar benefit for silver as well. Current testwork is showing about a 12 per cent reduction in zinc and silver in final tail, consistent with the original testwork. Sizing of the final tail during the tests showed that the reduction of zinc and silver losses were only in the <32 µm fraction, as would be expected from an aggregation process. However, the most surprising result was about a 4 per cent reduction in zinc and silver in the plant feed with a >99 per cent statistical certainty. The reduction in zinc and silver in the feed is also only in the <32 µm fraction. Therefore, because the magnetic conditioning of Zn flotation feed cannot impact plant ore feed grade the hypothesis is that the magnetic conditioning is reducing the fine mineral from downstream processes, like filtering and thickening, returning to the plant feed in the recycled process water. This hypothesis is consistent with plant observation of dirty concentrate thickener overflow and measurements of solids in the overflow, as well as the average % Zn grade in cyclone overflow that correlates with the magnetic conditioning ON and OFF days. This paper presents these plant test results.CITATION:Smiles, R and Lumsden, B, 2018. Improving fine sulfide mineral recovery in Independence Group’s Jaguar Mine zinc circuit, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 433–440 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By D Kay, M Lovitt

Mass Blasts are generally required at the completion of longhole stoping cycles to maximise the recovery of ore from a specific orebody. During the course of mining, the practice is to leave pillars of ore to support the opening left by extracted ore and to mitigate stresses from working areas of the stope. These pillars usually contain ore that has been included in the resource evaluation and is highly valuable to the mining operation. Due to their stressed nature, the removal of pillars by conventional blasting techniques, through small blasts, can result in pillars being reduced beyond their critical size and ultimately failing, rendering the ore unrecoverable. The AurionGold Kanowna Belle Gold Mine operates a Mine to Mill philosophy. This philosopy requires the fine tuning of blasting to provide the best possibe ore feed at the highest grade for mill productivity. This means that ore to the mill must be well fragmented from blasting that provides high extraction rates from draw points, with minimal dilution from overbreak or fall off, and sized to maximise SAG mill throughput. The AT04 Mass Blast contained significant ore reserves which were required to meet gold production targets. KBGB needed the AT04 Mass Blast to perform as well as if not better than conventional stope blasts to maintain mill production. This paper describes the circumstances, planning philosophy, techniques, including the use of Electronic Initiation Systems and Bulk Emulsion Explosives, and results that provided a highly successful outcome.

Jan 1, 2002

By Dobos K

The Clermont Goldfield, from which about 300,000 oz of bullion have been extracted, was one of the major gold producers in Queensland. This paper is derived from a systematic study of the mineralogy, geochemistry, and stable isotope geochemistry of the deposit, based on detailed field work and logging of 57 reverse-circulation percussion drilling holes at the Black Ridge Gold Deposit (Fig 1), aimed at addressing the long debated question of gold-ore genesis at Clermont, i.e., whether it is of fossil placer or hydrothermal origin.Detailed petrologic and mineralogical studies indicate the hydrothermal alteration at Black Ridge is dominated by extensive siderite (+rhodochrosite-ankerite) veinlets and stockworks, which are concentrated along the deformed unconformity between the Anakie Metamorphics and basal conglomerates of the early Permian Blair Athol Coal Measures. Siderite alteration is also moderately developed in all other rock units represented at Black Ridge, including the Tertiary basalt. Weak to moderate phyllosilicate alteration is common throughout the deposit, including chlorite-sericite along the shear zone of the unconformity, and sericite-clay in the conglomerates. A sulphide-oxides zonation also has occurred, including pyrite below the unconformity, (pyrite)-chalcopyrite-marcasite-(hematite) along the deformed unconformity, and marcasite (hematite, pyrite) in the conglomerates.

Jan 1, 1990

By A Scott, S Kanchibotla, J Segui

The æMine to MillÆ concept is not new. In fact, it is the underlying objective of every mine. Unfortunately, in many operations the management structure and reporting systems have created independent æbusinessesÆ within the overall mining enterprise. This has created incentives to optimise the performance of each component of the operation rather than the enterprise as a whole. The Mine to Mill Conference organised by The AusIMM in October 1998 documented a number of case studies where run of mine ore was not presented to the mill in the best possible form for subsequent stages of comminution and processing. A number of examples were quoted where modest expenditure in the mine had a very significant impact on downstream process efficiency and hence costs. Examples included:the minimisation of fines in the mining and handling of iron ore; the management of fines in blasting and crushing for a copper heap leach operation; the control of blast damage, mining recovery and dilution in open cut coal operations; and the optimisation of mine fragmentation to increase mill throughput in gold and copper operations. The latter topic has been trialed at a number of mines and is referred to as æMine to MillÆ fragmentation. A number of æMine to MillÆ type investigations have been reported in the literature including Pease et al, Simkus and Dance, Nielsen, Scott et al, Kojovic et al, Kanchibotla et al, Bulow et al and Hawkes from the 1998 Mine to Mill Conference. In addition, a number of studies are in progress or the results have yet to be published. These studies have demonstrated the feasibility of obtaining the data required to characterise the breakage behaviour of ores and to model the impact of changes to blasting practices on process efficiency. Characterising the breakage behaviour of ores is a vital step in the management of fragmentation and comminution in mines. The characteristics of importance to fragmentation fall outside the parameters conventionally required to describe the economic geology of a deposit. æMine to MillÆ optimisation of fragmentation means that the mining engineer needs information from the geologist in order to be able to help the metallurgist. Providing this information requires close interaction between these groups.

Jan 1, 2000

By H Cifuentes, D J. Williams

Despite the recognised importance of tailings management, there remain little data on the potential benefits of biological treatments compared with physical and chemical treatments. The operation of the majority of tailings storage facilities (TSFs) continues to employ mainly physical solutions, such as sub-aerial tailings slurry deposition, with increasing adoption of thickening, paste and filtration to dewater the tailings involving the addition of chemicals such as flocculants and coagulants. However, with tailings production continuing to escalate rapidly due to the increasing demand for commodities and reducing ore grades, available technologies have not demonstrated cost-effective performance at high tailings production rates. This paper examines the emerging role of bacteria to better manage tailings, reducing risks and optimising storage capacity. Bacteria have the potential to enhance tailings dewatering, maintain their permeability, delay the onset of desiccation cracking, and improve their shear strength. Bacteria-treated tailings may be suitable for use as construction materials. Bacteria also have potential in limiting the dusting of tailings and facilitating rehabilitation on closure. The paper describes a series of laboratory involving the addition of harmless bacteria to a range of tailings. The bacteria form a compact material called calcite (a common and stable form of calcium carbonate), which immobilises the tailings particles, releases water, and cements the tailings in a stable and natural matrix. The water released can be recovered or evaporated, depending on site objectives. The bacterial reactions are linked to physical and chemical processes, providing the potential for an optimal mix of technologies for particular tailings and site conditions.CITATION:Cifuentes, H and Williams, D J, 2018. Potential improvement of tailings geotechnical behaviour using bacteria, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 228–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By A Hacket, M Haest, I Vitins

Infrared spectroscopy has the ability to accurately measure mineralogy of drill cores, allowing for better spatial characterisation of iron ore deposits and potentially improving the prediction of key mining and processing parameters at the deposit scale. BHP Billiton Iron Ore is using infrared spectroscopic drill core logging to provide fast and accurate mineralogy for diamond cores and reverse circulation (RC) samples.Mineralogy can be predicted from infrared spectroscopic drill core data with errors on estimates ranging from six to 12 weight per cent. The error on the clay estimates is significantly lower than for hematite and goethite content estimates. This manuscript presents the results from a study on a bedded iron ore deposit, hosted in the Brockman iron formation, for which infrared spectroscopic data were collected on all of the diamond and RC drilling. Results show that these mineralogy estimates improve drill core logs, the geology model and the metallurgical block model.CITATION:Haest, M, Vitins, I and Hacket, A, 2013. Infrared spectroscopic drill core logging - making inroads to deposit scale 3D mineralogy, in Proceedings Iron Ore 2013 , pp 251-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By N Takamatsu

The environments surrounding the iron and steel industry have changed greatly in recent years. Reported in this paper are the technologies adopted by the Japanese iron and steel industry to fititself to change in global steel demands, degradation of iron ore and coal, prolonging service life of the facilities and requirements of energy saving. In addition, innovative technologies for CO2 emission control in iron making processes are also discussed.

Jul 11, 2011

By J Arola, B Kettunen, W M. Bond

Separation of fine and coarse particles as separate streams prior to flotation, and their differential treatments, could substantially increase recovery and reduce collector consumption. A series of simulations was carried out to quantify the benefits from plant scale implementation of such a treatment at the Ispat Inland flotation circuit (Minorca mine). The study involved detailed plant sampling and sample analysis to generate the data needed for simulation studies. Samples were taken from all the streams from flotation feed to final concentrate, as well as cell lips and cell pulp. Sampling was repeated for the second ore blend that was processed by the plant during different periods of a year. Sample analysis involved sieve analysis and size by size chemical analysis for total iron, magnetic iron and silica. Raw data were mass balanced, and flow rates within the circuit were calculated. Mass balanced data were used to calculate model parameters representing the existing conditions. Usim Pac was used for both mass balancing and simulation studies. Available pilot and bench scale data were utilised to define the modified flow sheet and expected performance. The simulated flow sheet included classification of flotation circuit feed by hydrocyclones. While the coarse fraction followed the existing flow sheet, the fine fraction was sent to a magnetic separator. Magnetic and rougher flotation concentrates were combined to form the final concentrate. Two simulations for each blend were carried out. The first one assumed that there would be no change in size by size kinetic behaviours of both gangue and magnetite due to this modification. This was named as the worst case scenario, in which particles had a longer residence time due to reduced flow rates within the flotation cells. The second scenario anticipated that there would be an increase in recoveries of gangue and magnetite going into froth launder due to more efficient use of collector in absence of fines. Results showed that pre-classification of flotation feed could improve the flotation recovery by 0.3 - 0.5 per cent, with the major benefit being significant reduction (40 - 60 per cent) in the amount of collector used.

Jan 1, 2005

By J Li, J Regan, D Payne

The Caval Ridge Mine is an open cut coalmine and located within the Bowen Basin region in Central Queensland, and commenced mining and processing operations in 2014. A number of geotechnical challenges for managing dragline bench and lowwall stabilities have been encountered in both southern and northern pits over the years. Southern Pits contain steep seam dips of up to 15° (27 per cent) whilst the northern pits also have shears below pit floors. Geotechnical guidelines to manage the risk of dragline bench failure and lowwall instability have been developed and improved since these geotechnical challenges were identified. The dragline guidelines include dragline tub offset distances from the 60° Line (SDL) or buttressing thickness for different seam dips greater than or equal to 8°. The low wall stabilisation guideline established floor disruption widths and depths depending on seam dips and presence of floor shears to known depths of up to 3 m. As mining operations advance, lowwalls have remained stable until floor disruptions were fired, then returned to stable soon after the shot. The maximum distance of lowwall cracking with blasting has been as far back as the second spoil peak (the prestrip truck dumps construction limit). These failures need to be eliminated to allow the operational flexibility and haulage benefit of constructing the prestrip truck dumps behind the first spoil peak, while maintaining no risk to personnel or equipment. The floor shear depth was verified by collaborating with the exploration teams and taking advantage of the already planned 8-inch coal quality core holes, drilling them an extra 5–10 m past the coal seam floor and locating the shear presence. With this continuous improvement effort, no lowwall failures have occurred during floor disruption firing from the second strip after the new floor disruption depth guidance have been applied. This paper documents the processes for developing these geotechnical guidelines, operational implementation, and outcomes. Operational applications over the years confirmed that these guidelines have effectively managed the dragline bench and lowwall failure risks related with the steep seam dips and floor shears in this open cut coalmine.

Nov 29, 2022

By J Janus, J Krawczyk

Local accumulation of methane in workings of a longwall is one of the most common causes of mining accidents. This gas has many sources: it may leak from goaf through permeable sealings, or through gaps between roof support sections. This stream is then mixed with ventilation air. In the case of auxiliary ventilation ducts, or free jet fans, we have to consider the propagation of a clean air stream in areas with an air-methane mixture. Therefore, modelling the mixing process of methane with ventilation air is important for determining the hazardous areas and thus to ensure safety. Computational fluid dynamics (CFD), specifically the finite volume method, provides tools for such modelling. However, this method requires validation. For this purpose, we have compared measurements with simulations for selected test cases having sufficient similarity to the present problems. In typical methane explosion hazard areas, such as a longwall, it is difficult to make measurements sufficiently to confirm credibility of 3D CFD simulations. As a relevant alternative, an injector methane drainage station placed in an underground gallery has been selected. The stream of drained goaf methane is entrained by compressed air powered injectors and then mixed with ventilation air. Research in this area does not interfere with mining operations, it can be performed safely in a repeatable way. Flow within the site has many similarities to conditions in mine drifts of the longwall area. Comparative research of measuring the methane concentration distribution in the mine drift downstream injector station, with simulations of propagation of the methane stream, was carried out. For measuring the methane concentration distribution in the mine drift a multipoint measurement velocity system developed at the Strata Mechanics Research Institute was used. For the simulation a finite volume method for turbulent flow of gas mixtures was applied. Preliminary results of comparison are shown as graphs and tables.CITATION:Janus, J and Krawczyk, J, 2013. An analysis of the mixing of air and methane in the stream produced by the mine injector station - Presenting preliminary results of measurements and modelling, in Proceedings The Australian Mine Ventilation Conference , pp 49-56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

The past year has been a difficult one for the mining industry in this country, but an active and successful one for the Branch. Membership has continued to increase, albeit at a slower rate than last year, and with the increase almost all from student membership. I dwelt at some length last year on the continued increase in student membership, which I ascribed largely to deliberate policies adopted by the Branch to foster this area of membership. I don't propose to reiterate these, suffice it to say that as usual, the Otago School of Mines has been a prolific source of student members, and it will be a pity if this source dries up û more on this subject later. In fact, students form just on 29 per cent of the Branch's total membership û a far higher percentage than for any other Branch in the Institute, whose membership as a whole comprises only ten per cent students.

Jan 1, 1985

By Greg Brown

The underwriting of professional negligence has proved to be an evolving science. As with most insurance products coverage offered in the past was very broad but as legal precedent demonstrated to Insurers areas of unforeseen exposure policy documents per se have become more restrictive until today the insurance market through attrition have produced a basic policy structure with various purchasable extensions which together provide insuring professionals with coverage that has proved to be adequate for their needs. The basic policy provides indemnity and protection for fortuitous negligence. In a practical sense, however, professional indemnity policies are really a defence document in so far as policy holders are relying upon the expertise of Insurers to protect them in the event that a claim is made upon them. Whether damages are awarded is in many respects a secondary consideration, the most important factor is to ensure that policy holders are protected in terms of the legal defence mechanism. By way of illustration we are currently in the process of defending a large professional firm which purchased from us a policy with a limit of indemnity of $10M. The case has been running in a Supreme Court now for 14 months and the defence costs which we have incurred on their behalf are rising close to $8M as I put pen to paper. Defence costs of that magnitude would in effect terminally cripple all but the very largest professional operations in Australia. In more recent times coverage has been provided in Australia for breaches of the Trade Practices Act and similar legislation enacted in various States. No-one really appreciated the comprehensive impact which the Trade Practices Act would have on commerce in Australia. Most professionals thought that indeed they would be exempt from prosecution under this Act. The passage of time has clearly indicated that this is not the case and we have found that it is much more difficult to defend a claim involving breaches of the Trade Practices Act than it would be to defend a claim for breach of tortuous liability.

Jan 1, 1995

By R Linares

The efficient operation of any modern metallurgical facility depends on the accurate measurement and estimation of flow rates, inventories, and composition of their intermediate and final products. All of this information is subject to both statistical errors and gross errors, which can lead to poor estimation of efficiency, yields and specific energy consumption. The detection and the elimination of these errors require not only plant data, but also product transactions and the operational events. Once the gross errors have been eliminated, it is possible to estimate validated performance indicators, such as grade recovery or yields. This paper describes the methodology to implement a unification and gross error detection system using the available infrastructure of both information and data reconciliation system. It covers the different infrastructure layers, from the data collection layer to the data validation and reconciliation layer. In addition, the impact of these methodologies on the decision-making process is presented.

Jan 1, 2005

By R Gilbertson, N Freeman

Metallurgical accounting is key to the control and production planning process of any mining operation. This is even more crucial for complex operations involving mining, concentration, smelting, refining and marketing. The tracking of multiple metal product and contaminant components through the operation can improve process predictability and inventory management. Appropriate use can be made of æhigh quality dataÆ for strategic reserve utilisation, mining operations, milling operations, etc. This information enables the optimisation of all aspects of the mining and processing operations. This case study discusses a metal balance implementation for WMCÆs Olympic Dam operations; a large integrated mining, concentration and refining operation, which used an existing off the shelf statistical data reconciliation package developed for the oil industry. It was extended to track and balance the metal co-products across the entire integrated mining, mineral processing and refining plant. The key benefits discussed are tight integration with existing data collection systems, formalisation of previously informal processes, and leveraging the development and support available for a widely used package. The project provided a solution for the site metallurgical balance spanning the mine and processing plant. The solution facilitates a bridge between the planning and production worlds, using a common data model across the site.

Jan 1, 2002